diff --git a/lib/cable_holder.scad b/lib/cable_holder.scad
index 77a6be0..b7f22ff 100644
--- a/lib/cable_holder.scad
+++ b/lib/cable_holder.scad
@@ -37,9 +37,9 @@ module cableholder_spacer(length) {
     difference() {
         union() {
             translate([size[0]/2,size[0]/2,0]) rotate([0,0,90]) long_slot(size[0],size[1],size[2]);
-            translate([-length,5,3]) rotate([0,90,0]) cylinder(d=6, h=length+1);
+            translate([-length,5,3]) rotate([0,90,0]) cylinder(d=6, h=length+9.4);
         }
-        translate([-length-adj,5,3]) rotate([0,90,0]) cylinder(d=3.2, h=length+size[0]+adj);
+        translate([-length-adj,5,3]) rotate([0,90,0]) cylinder(d=3.2, h=length+size[0]+2*adj);
         translate([-1,8,-1]) cube([2,20,9]);
         translate([5,9.5,-1]) rotate([0,0,90]) long_slot(4.5,11,9);
         translate([3,20,-1]) rotate([0,0,45]) cube([2,6,9]);
diff --git a/mod/case_bottom.scad b/mod/case_bottom.scad
index c8eafc2..808f182 100644
--- a/mod/case_bottom.scad
+++ b/mod/case_bottom.scad
@@ -157,11 +157,11 @@ module case_bottom(case_design) {
                         // front panel
                         if(case_design == "tray_vu5" || case_design == "tray_vu7" || case_design == "tray_sides") {
                             translate([-wallthick-gap,depth-(2*wallthick)-gap,bottom_height-adj]) 
-                                rotate([0,0,0]) cube([width,wallthick,top_height]);
+                                cube([width,wallthick,top_height]);
                         }
                         else {
                             translate([-wallthick-gap,depth-(2*wallthick)-gap,bottom_height-adj]) 
-                                rotate([0,0,0]) cube([width,wallthick,top_height-floorthick]);
+                                cube([width,wallthick,top_height-floorthick]);
                         }
                         
                         // rear panel
@@ -236,21 +236,21 @@ module case_bottom(case_design) {
                         }
                         else {
                             difference() {
-                                translate([pcb_width/2,pcb_depth/2,bottom_height/2]) rotate([0,0,0]) 
+                                translate([pcb_width/2,pcb_depth/2,bottom_height/2]) 
                                     cylinder_fillet_inside(h=bottom_height, r=hex_diameter/2, 
                                         top=0, bottom=edge_fillet, $fn=6, fillet_fn=case_ffn, center=true);
-                                translate([pcb_width/2,pcb_depth/2,(bottom_height/2)+floorthick]) rotate([0,0,0]) 
+                                translate([pcb_width/2,pcb_depth/2,(bottom_height/2)+floorthick]) 
                                     cylinder_fillet_inside(h=bottom_height+adj,r=(hex_diameter/2)-lip/2,top=0, 
                                         bottom=edge_fillet-1,$fn=6,fillet_fn=case_ffn, center=true);
                                 difference() {
-                                    translate([pcb_width/2,pcb_depth/2,bottom_height-lip]) rotate([0,0,0]) 
+                                    translate([pcb_width/2,pcb_depth/2,bottom_height-lip]) 
                                         cylinder(h=lip+adj,r=(hex_diameter/2)+1, $fn=6);
-                                    translate([pcb_width/2,pcb_depth/2,bottom_height-lip]) rotate([0,0,0]) 
+                                    translate([pcb_width/2,pcb_depth/2,bottom_height-lip]) 
                                         cylinder(h=lip+2*adj,r=(hex_diameter/2)-lip/4, $fn=6);
                                 }
                             }
                             difference() {
-                                translate([pcb_width/2,pcb_depth/2,(bottom_height/2)+2*floorthick]) rotate([0,0,0]) 
+                                translate([pcb_width/2,pcb_depth/2,(bottom_height/2)+2*floorthick]) 
                                     cylinder_fillet_inside(h=bottom_height+adj+floorthick+lip,
                                         r=(hex_diameter/2)-lip/2,top=0, bottom=edge_fillet-1, $fn=6, 
                                             fillet_fn=case_ffn, center=true);
@@ -515,9 +515,11 @@ echo(pcb_depth+case_offset_y-10);
                 }
                 // bottom cover pattern
                 if(bottom_cover_pattern != "solid") {
+                    xvent8_adj = pcb_width > 100 ? width/5.5 : width/6;
                     if(bottom_cover_pattern == "hex_5mm") {
                         if(case_design == "panel_nas") { 
-                            translate([5,5,-floorthick]) vent_hex((width-10)/3.75,(depth-10)/7,floorthick+4,5,1.5,"horizontal");
+                            translate([6,5,-floorthick+adj]) 
+                                vent_hex((width-10)/3.75,(depth-10)/7,floorthick+4,5,1.5,"horizontal");
                         }
                         else {
                             translate([1,0,-floorthick]) vent_hex(width/3.75,depth/6,floorthick+4,5,1.5,"horizontal");
@@ -525,7 +527,7 @@ echo(pcb_depth+case_offset_y-10);
                     }
                     if(bottom_cover_pattern == "hex_8mm") {
                         if(case_design == "panel_nas") { 
-                            translate([5,6,-floorthick]) vent_hex(width/5.5,depth/9.5,floorthick+4,8,1.5,"horizontal");
+                            translate([-gap+5,6,-floorthick+adj]) vent_hex(xvent8_adj,depth/9.5,floorthick+4,8,1.5,"horizontal");
                         }
                         else {
                             translate([1,2,-floorthick]) vent_hex(width/5.5,depth/9.5,floorthick+4,8,1.5,"horizontal");
@@ -533,8 +535,8 @@ echo(pcb_depth+case_offset_y-10);
                     }
                     if(bottom_cover_pattern == "linear_vertical") {
                         if(case_design == "panel_nas") { 
-                            translate([6,5,-floorthick]) 
-                                vent(wallthick,depth-8*wallthick-gap,floorthick+4,1,1,(width-2*wallthick-gap)/4.5,"horizontal");
+                            translate([wallthick+gap,wallthick,-floorthick+adj]) 
+                                vent(wallthick,depth-6*wallthick-gap,floorthick+4,1,1,(width-2*(sidethick+gap))/5.35,"horizontal");
                         }
                         else {
                             translate([0,-gap,-floorthick])
@@ -543,8 +545,9 @@ echo(pcb_depth+case_offset_y-10);
                     }
                     if(bottom_cover_pattern == "linear_horizontal") {
                         if(case_design == "panel_nas") { 
-                            translate([6,5,-floorthick]) 
-                                vent(width-6*(sidethick+gap),wallthick,floorthick+4,1,(depth-2*wallthick-gap)/3.25,1,"horizontal");
+                            translate([wallthick+gap,wallthick,-floorthick+adj]) 
+                                vent(width-4*(sidethick+gap),wallthick,floorthick+4,1,
+                                    (depth-2*(wallthick-gap))/4.35,1,"horizontal");
                         }
                         else {
                             translate([-gap,-gap,-floorthick]) 
@@ -553,9 +556,10 @@ echo(pcb_depth+case_offset_y-10);
                     }
                     if(bottom_cover_pattern == "astroid") {
                         if(case_design == "panel_nas") { 
-                        for(c=[12:12:depth-16]) {
+                        xast_adj = pcb_width <= 100 ? 8 : 6;
+                        for(c=[xast_adj:12:depth-16]) {
                             for(r=[12:12:width-16]) {
-                                translate([r,c,-(2*floorthick)]) linear_extrude(floorthick+5) import("./dxf/astroid_8mm.dxf");
+                                translate([r,c,-floorthick]) linear_extrude(floorthick+5) import("./dxf/astroid_8mm.dxf");
                                 }
                             }
                         }
diff --git a/mod/case_side.scad b/mod/case_side.scad
index d6f94fd..040701b 100644
--- a/mod/case_side.scad
+++ b/mod/case_side.scad
@@ -131,6 +131,7 @@ module case_side(case_design, side) {
             if(case_design == "panel_nas") {
                 x_adj = pcb_width > 100 ? width-2*sidethick : width-2*(gap+sidethick);
                 xtab_adj = pcb_width > 100 ? width-gap-2*sidethick-adj : width-gap-2*(gap+sidethick)-adj;
+                xvent8_adj = pcb_width > 100 ? width/5.5 : width/6;
                 if(side == "rear") {
                     difference() {
                         union() {
@@ -208,38 +209,41 @@ module case_side(case_design, side) {
                         }
                         // front cover pattern
                         if(front_cover_pattern != "solid" && case_design == "panel_nas") {
+                            xvent_pos = pcb_width <= 100 ? -gap+3 : -gap+6;
                             if(front_cover_pattern == "hex_5mm" && hd_bays < 6) {
-                                translate([-gap+4,depth-3*(wallthick)+gap,hd_z_position])
-                                    vent_hex(width/3.85,hd_bays*(27.1+hd_space)/5.75,wallthick+4,5,1.5,"vertical");
+                                translate([xvent_pos,depth-3*(wallthick)+gap,hd_z_position-5])
+                                    vent_hex(round(width/3.85),round(hd_bays*(27.1+hd_space)/5.75),wallthick+4,5,1.5,"vertical");
                             }
                             if(front_cover_pattern == "hex_5mm" && hd_bays == 6) {
-                                translate([-gap+4,depth-3*(wallthick)+gap,hd_z_position])
-                                    vent_hex(width/3.85,hd_bays*(27.1+hd_space)/7,wallthick+4,5,1.5,"vertical");
+                                translate([xvent_pos,depth-3*(wallthick)+gap,hd_z_position])
+                                    vent_hex(round(width/3.85),round(hd_bays*(27.1+hd_space)/5.75),wallthick+4,5,1.5,"vertical");
                             }
                             if(front_cover_pattern == "hex_8mm") {
-                                translate([-gap+5,depth-3*(wallthick)+gap,5]) 
-                                    vent_hex(width/5.5,(case_z-6)/10,floorthick+4,8,1.5,"vertical");
+                                translate([-gap+4,depth-3*(wallthick)+gap,hd_z_position]) 
+                                    vent_hex(xvent8_adj,round(hd_bays*(27.1+hd_space)/5.75)-5,floorthick+4,8,1.5,"vertical");
                             }
                             if(front_cover_pattern == "linear_vertical") {
                                 translate([-gap+4,depth-3*(wallthick)+gap,hd_z_position]) 
                                     vent(wallthick,(case_z-2*(wallthick+gap)-20)/8,floorthick+4,1,1,
-                                        (width-2*(wallthick+gap+sidethick))/4.2,"vertical");
-                                translate([-gap+4,depth-3*(wallthick)+gap,case_z-(top_height+bottom_height+4*floorthick)]) 
+                                        (width-2*(sidethick+gap))/5.35,"vertical");
+                                translate([-gap+4,depth-3*(wallthick)+gap,case_z-(top_height+bottom_height+4*floorthick)-5]) 
                                     vent(wallthick,(case_z-2*(wallthick+gap)-20)/8,floorthick+4,1,1,
-                                        (width-2*(wallthick+gap+sidethick))/4.2,"vertical");
+                                        (width-2*(sidethick+gap))/5.35,"vertical");
                             }
                             if(front_cover_pattern == "linear_horizontal") {
-                                translate([-gap+4,depth-3*(wallthick)+gap,hd_z_position]) 
-                                    vent(width-2*(wallthick+gap+sidethick)-4,wallthick,floorthick+4,2,
-                                        (case_z-2*(wallthick+gap)-20)/20,1,"vertical");
-                                translate([-gap+4,depth-3*(wallthick)+gap,case_z-(top_height+bottom_height+4*floorthick)-20]) 
+                                translate([wallthick+gap,depth-3*(wallthick)+gap,hd_z_position]) 
                                     vent(width-2*(wallthick+gap+sidethick)-4,wallthick,floorthick+4,2,
                                         (case_z-2*(wallthick+gap)-20)/20,1,"vertical");
+                                translate([wallthick+gap,depth-3*(wallthick)+gap,
+                                    case_z-(top_height+bottom_height+4*floorthick)-20]) 
+                                        vent(width-4*(sidethick+gap),,wallthick,floorthick+4,2,
+                                            (case_z-2*(wallthick+gap)-20)/20,1,"vertical");
                             }
                             if(front_cover_pattern == "astroid") {
-                                for(c=[10:12:case_z-20]) {
-                                    for(r=[6:12:width-8]) {
-                                        translate([r,depth-wallthick,c]) rotate([90,0,0])
+                                xast_adj = pcb_width <= 100 ? 8 : 6;
+                                for(c=[xast_adj:12:case_z-20]) {
+                                    for(r=[8:12:width-8]) {
+                                        translate([r,depth-2*wallthick,c]) rotate([90,0,0])
                                             linear_extrude(wallthick+5) import("./dxf/astroid_8mm.dxf");
                                     }
                                 }   
@@ -287,13 +291,13 @@ module case_side(case_design, side) {
                             translate([width-3*sidethick+gap-adj,depth-(4*wallthick),(case_z/2)-5]) 
                                 cube([2*sidethick+2*adj,wallthick+tol,20]);
                             translate([width-3*sidethick+gap-adj,depth-(4*wallthick),(case_z/2)-5+10]) 
-                                cube([2*sidethick+(2*adj),2*wallthick,10+tol]);
+                                cube([2*sidethick+(2*adj),3*wallthick,10+tol]);
 
                             // rear edge middle tab openings
                             translate([width-3*sidethick+gap-adj,-2*wallthick+adj,(case_z/2)-5]) 
                                 cube([2*sidethick+2*adj,wallthick+tol,20]);
                             translate([width-3*sidethick+gap-adj,-(4*wallthick),(case_z/2)-5+10]) 
-                                cube([2*sidethick+(2*adj),2*wallthick,10+tol]);
+                                cube([2*sidethick+(2*adj),3*wallthick,10+tol]);
                         }
 
                         // hd holes for bays
@@ -350,13 +354,13 @@ module case_side(case_design, side) {
                         translate([-sidethick-gap-adj,-2*wallthick+adj,case_z-30]) 
                             cube([sidethick+2*adj,wallthick+tol,20]);
                         translate([-sidethick-gap-adj,-(4*wallthick),case_z-20-tol]) 
-                            cube([sidethick+(2*adj),2*wallthick,10+tol]);
+                            cube([sidethick+(2*adj),3*wallthick+adj,10+tol]);
 
-                        // rear edge botom tab openings
+                        // rear edge bottom tab openings
                         translate([-sidethick-gap-adj,-2*wallthick+adj,20]) 
                             cube([sidethick+2*adj,wallthick+tol,20]);
                         translate([-sidethick-gap-adj,-(4*wallthick),30-tol]) 
-                            cube([sidethick+(2*adj),2*wallthick,10+tol]);
+                            cube([sidethick+(2*adj),3*wallthick,10+tol]);
 
                         // front edge top tab openings
                         translate([-sidethick-gap-adj,depth-(4*wallthick),case_z-30])
@@ -375,7 +379,7 @@ module case_side(case_design, side) {
                         translate([-sidethick-gap-adj,-2*wallthick+adj,(case_z/2)-5]) 
                             cube([sidethick+2*adj,wallthick+tol,20]);
                         translate([-sidethick-gap-adj,-(4*wallthick),(case_z/2)-5+10]) 
-                            cube([sidethick+(2*adj),2*wallthick,10+tol]);
+                            cube([sidethick+(2*adj),3*wallthick,10+tol]);
 
                         // front edge middle tab openings
                         translate([-sidethick-gap-adj,depth-(4*wallthick),(case_z/2)-5]) 
@@ -388,7 +392,7 @@ module case_side(case_design, side) {
                         if(hd_reverse == false) {
                             for( i=[0:1:hd_bays-1]) {
                                 translate([-gap+adj,-(3*wallthick)-gap+hd_y_position,hd_z_position+(hd_space+27.1)*i]) 
-                                    rotate([0,0,0]) hd_holes(3.5, "portrait", "both", sidethick+2);
+                                    hd_holes(3.5, "portrait", "both", sidethick+2);
                             }
                         }
                         else {
diff --git a/mod/case_top.scad b/mod/case_top.scad
index 2179459..6332a97 100644
--- a/mod/case_top.scad
+++ b/mod/case_top.scad
@@ -111,8 +111,8 @@ module case_top(case_design) {
                                         bottom=[0,0,0,0], $fn=90);
                             translate([(width/2)-wallthick-gap,(depth/2)-wallthick-gap,(case_z/2)-floorthick+.25]) 
                                 cube_fillet_inside([width+1,depth+(wallthick*2),case_z], 
-                                    vertical=[corner_fillet-wallthick,corner_fillet-wallthick,corner_fillet-wallthick,corner_fillet-wallthick],
-                                        top=[0,0,0,0],bottom=[0,0,0,0], $fn=90);
+                                    vertical=[corner_fillet-wallthick,corner_fillet-wallthick,corner_fillet-wallthick,
+                                        corner_fillet-wallthick],top=[0,0,0,0],bottom=[0,0,0,0], $fn=90);
                             for (i=[1:11:len(sbc_data[s[0]])-2]) {
                                 class = sbc_data[s[0]][i+1];
                                 type = sbc_data[s[0]][i+2];
@@ -228,13 +228,13 @@ module case_top(case_design) {
                         }
                         else {
                             difference() {
-                                translate([pcb_width/2,pcb_depth/2,bottom_height+(top_height/2)-lip/2]) rotate([0,0,0]) 
+                                translate([pcb_width/2,pcb_depth/2,bottom_height+(top_height/2)-lip/2]) 
                                     cylinder_fillet_inside(h=top_height+lip, r=hex_diameter/2, 
                                         top=edge_fillet, bottom=0, $fn=6, fillet_fn=case_ffn, center=true);
                                 translate([pcb_width/2,pcb_depth/2,bottom_height+(top_height/2)-floorthick-lip/2])
-                                    rotate([0,0,0]) cylinder_fillet_inside(h=top_height+lip, r=(hex_diameter/2)-wallthick, 
+                                    cylinder_fillet_inside(h=top_height+lip, r=(hex_diameter/2)-wallthick, 
                                         top=edge_fillet-1, bottom=0, $fn=6, fillet_fn=case_ffn, center=true);
-                                translate([pcb_width/2,pcb_depth/2,bottom_height-adj-lip/2]) rotate([0,0,0]) 
+                                translate([pcb_width/2,pcb_depth/2,bottom_height-adj-lip/2]) 
                                     cylinder_fillet_inside(h=lip+2*adj, r=(hex_diameter/2)-wallthick/2+tol/2, 
                                         top=edge_fillet-1, bottom=0, $fn=6, fillet_fn=case_ffn, center=true);
                                 // io cutout
@@ -267,21 +267,22 @@ module case_top(case_design) {
                             
                             translate([(width/2)-wallthick-gap,(depth/2)-wallthick-gap,case_z-adj]) 
                                 cube_fillet_inside([width-(3*wallthick),depth-(3*wallthick),2*floorthick+1.5+adj], 
-                                    vertical=[corner_fillet-wallthick,corner_fillet-wallthick,corner_fillet-wallthick,corner_fillet-wallthick],top=[0,0,0,0],
-                                        bottom=[edge_fillet,edge_fillet,edge_fillet,edge_fillet,edge_fillet], $fn=90);
+                                    vertical=[corner_fillet-wallthick,corner_fillet-wallthick,corner_fillet-wallthick,
+                                        corner_fillet-wallthick],top=[0,0,0,0],
+                                            bottom=[edge_fillet,edge_fillet,edge_fillet,edge_fillet,edge_fillet], $fn=90);
                         }
                         // snap top outdent
                         difference() {
                             translate([-wallthick-gap+1.25+tol,(depth/2)-((depth*.75)/2)+2.5-gap-wallthick,case_z-.5]) 
                                 rotate([0,45,0]) cube([4,(depth*.75)-5,4]);
                             translate([-wallthick-gap+3,(depth/2)-((depth*.75)/2)+1.25-gap-wallthick,case_z+floorthick-5.75]) 
-                                rotate([0,0,0]) cube([6,(depth*.75)-2,6]);
+                                cube([6,(depth*.75)-2,6]);
                         }
                         difference() {
                             translate([width-wallthick-gap-6.8-tol,(depth/2)-((depth*.75)/2)+2.5-gap-wallthick,case_z-.5])
                                 rotate([0,45,0]) cube([4,(depth*.75)-5,4]);
-                            translate([width-wallthick-gap-8.5,(depth/2)-((depth*.75)/2)+1.25-gap-wallthick,case_z+floorthick-5.75])
-                                rotate([0,0,0]) cube([6,(depth*.75)-2,6]);
+                            translate([width-wallthick-gap-8.5,(depth/2)-((depth*.75)/2)+1.25-gap-wallthick,
+                                case_z+floorthick-5.75]) cube([6,(depth*.75)-2,6]);
                         }
                     }
                     if(case_design == "fitted") {
@@ -461,6 +462,7 @@ module case_top(case_design) {
                 }
                 // top cover pattern
                 if(top_cover_pattern != "solid") {
+                    xvent8_adj = pcb_width > 100 ? width/5.5 : width/6;
                     if(top_cover_pattern == "hex_5mm") {
                         if(case_design == "panel_nas") { 
                             translate([6,5,case_z-(2*floorthick)])
@@ -472,7 +474,7 @@ module case_top(case_design) {
                     }
                     if(top_cover_pattern == "hex_8mm") { 
                         if(case_design == "panel_nas") { 
-                            translate([5,6,case_z-(2*floorthick)]) vent_hex(width/5.5,depth/9.5,floorthick+4,8,1.5,"horizontal");
+                            translate([-gap+5,6,case_z-(2*floorthick)]) vent_hex(xvent8_adj,depth/9.5,floorthick+4,8,1.5,"horizontal");
                         }
                         else {
                             translate([1,2,case_z-(2*floorthick)]) vent_hex(width/5.5,depth/9.5,floorthick+4,8,1.5,"horizontal");
@@ -481,7 +483,7 @@ module case_top(case_design) {
                     if(top_cover_pattern == "linear_vertical") {
                         if(case_design == "panel_nas") { 
                             translate([wallthick+gap,wallthick,case_z-(2*floorthick)]) 
-                                vent(wallthick,depth-6*wallthick-gap,floorthick+4,1,1,(width-2*(sidethick+gap))/4.25,"horizontal");
+                                vent(wallthick,depth-6*wallthick-gap,floorthick+4,1,1,(width-2*(sidethick+gap))/5.35,"horizontal");
                         }
                         else {
                             translate([0,-gap,case_z-(2*floorthick)]) 
@@ -491,8 +493,8 @@ module case_top(case_design) {
                     if(top_cover_pattern == "linear_horizontal") {
                         if(case_design == "panel_nas") { 
                             translate([wallthick+gap,wallthick,case_z-(2*floorthick)]) 
-                                vent((width-4*(sidethick+gap)),wallthick,floorthick+4,1,
-                                    (depth-2*(wallthick-gap))/3.25,1,"horizontal");
+                                vent(width-4*(sidethick+gap),wallthick,floorthick+4,1,
+                                    (depth-2*(wallthick-gap))/4.35,1,"horizontal");
                         }
                         else {
                             translate([-gap,-gap,case_z-(2*floorthick)]) 
@@ -500,9 +502,10 @@ module case_top(case_design) {
                         }
                     }
                     if(top_cover_pattern == "astroid") {
+                        xast_adj = pcb_width <= 100 ? 8 : 6;
                         if(case_design == "panel_nas") { 
-                            for(c=[12:12:depth-16]) {
-                                for(r=[12:12:width-16]) {
+                            for(c=[xast_adj:12:depth-16]) {
+                                for(r=[8:12:width-16]) {
                                     translate([r,c,case_z-(2*floorthick)-adj]) 
                                         linear_extrude(floorthick+5) import("./dxf/astroid_8mm.dxf");
                                 }
diff --git a/sbc_case_builder.json b/sbc_case_builder.json
index 2098484..499ae11 100644
--- a/sbc_case_builder.json
+++ b/sbc_case_builder.json
@@ -3131,6 +3131,223 @@
             "view": "model",
             "wallthick": "2.5"
         },
+        "m1_panel_nas": {
+            "$fn": "90",
+            "access_panel_location": "[10, 15]",
+            "access_panel_orientation": "landscape",
+            "access_panel_rotation": "0",
+            "access_panel_size": "[70, 30]",
+            "accessory_highlight": "false",
+            "accessory_name": "none",
+            "adj": "0.01",
+            "bend_allowance": "1",
+            "bottom_access_panel_enable": "false",
+            "bottom_clearence": "3.5",
+            "bottom_cover_pattern": "solid",
+            "bottom_front_left_adjust": "0",
+            "bottom_front_left_enable": "true",
+            "bottom_front_left_support": "front",
+            "bottom_front_right_adjust": "0",
+            "bottom_front_right_enable": "true",
+            "bottom_front_right_support": "front",
+            "bottom_rear_left_adjust": "0",
+            "bottom_rear_left_enable": "true",
+            "bottom_rear_left_support": "rear",
+            "bottom_rear_right_adjust": "0",
+            "bottom_rear_right_enable": "true",
+            "bottom_rear_right_support": "rear",
+            "bottom_sidewall_support": "false",
+            "bottom_standoff_diameter": "5.75",
+            "bottom_standoff_hole_size": "3.4",
+            "bottom_standoff_insert": "false",
+            "bottom_standoff_insert_dia": "4.2",
+            "bottom_standoff_insert_height": "5.1",
+            "bottom_standoff_pillar": "hex",
+            "bottom_standoff_reverse": "false",
+            "bottom_standoff_size": "m3",
+            "bottom_standoff_support_height": "4",
+            "bottom_standoff_support_size": "10",
+            "bottom_standoff_type": "countersunk",
+            "case_design": "panel_nas",
+            "case_offset_bz": "-5",
+            "case_offset_tz": "-15",
+            "case_offset_x": "10",
+            "case_offset_y": "20",
+            "cooling": "open",
+            "corner_fillet": "3",
+            "edge_fillet": "0",
+            "ext_bottom_front_left_adjust": "0",
+            "ext_bottom_front_left_enable": "true",
+            "ext_bottom_front_left_support": "front",
+            "ext_bottom_front_right_adjust": "0",
+            "ext_bottom_front_right_enable": "true",
+            "ext_bottom_front_right_support": "front",
+            "ext_bottom_rear_left_adjust": "0",
+            "ext_bottom_rear_left_enable": "true",
+            "ext_bottom_rear_left_support": "rear",
+            "ext_bottom_rear_right_adjust": "0",
+            "ext_bottom_rear_right_enable": "true",
+            "ext_bottom_rear_right_support": "rear",
+            "ext_bottom_sidewall_support": "true",
+            "ext_bottom_standoff_diameter": "5.75",
+            "ext_bottom_standoff_hole_size": "3.4",
+            "ext_bottom_standoff_insert": "false",
+            "ext_bottom_standoff_insert_dia": "4.2",
+            "ext_bottom_standoff_insert_height": "5.1",
+            "ext_bottom_standoff_pillar": "hex",
+            "ext_bottom_standoff_reverse": "false",
+            "ext_bottom_standoff_size": "m3",
+            "ext_bottom_standoff_support_height": "4",
+            "ext_bottom_standoff_support_size": "10",
+            "ext_bottom_standoff_type": "countersunk",
+            "ext_bottom_standoffs": "false",
+            "ext_top_front_left_adjust": "0",
+            "ext_top_front_left_enable": "true",
+            "ext_top_front_left_support": "front",
+            "ext_top_front_right_adjust": "0",
+            "ext_top_front_right_enable": "true",
+            "ext_top_front_right_support": "front",
+            "ext_top_rear_left_adjust": "0",
+            "ext_top_rear_left_enable": "true",
+            "ext_top_rear_left_support": "rear",
+            "ext_top_rear_right_adjust": "0",
+            "ext_top_rear_right_enable": "true",
+            "ext_top_rear_right_support": "rear",
+            "ext_top_sidewall_support": "true",
+            "ext_top_standoff_diameter": "5.75",
+            "ext_top_standoff_hole_size": "2.75",
+            "ext_top_standoff_insert": "false",
+            "ext_top_standoff_insert_dia": "4.2",
+            "ext_top_standoff_insert_height": "5.1",
+            "ext_top_standoff_pillar": "hex",
+            "ext_top_standoff_reverse": "true",
+            "ext_top_standoff_size": "m3",
+            "ext_top_standoff_support_height": "4",
+            "ext_top_standoff_support_size": "10",
+            "ext_top_standoff_type": "blind",
+            "ext_top_standoffs": "false",
+            "fan_size": "0",
+            "flat_blank_section": "false",
+            "floorthick": "3",
+            "front_cover_pattern": "hex_5mm",
+            "gap": "1",
+            "gpio_opening": "default",
+            "hd_bays": "1",
+            "hd_center": "false",
+            "hd_reverse": "true",
+            "hd_space": "10",
+            "hd_y_position": "25",
+            "hd_z_position": "45",
+            "indents": "true",
+            "individual_part": "bottom",
+            "lower_bottom": "0",
+            "material_thickness": "0.5",
+            "move_front": "0",
+            "move_leftside": "0",
+            "move_rear": "0",
+            "move_rightside": "0",
+            "multipcb_bottom_front_left_adjust": "0",
+            "multipcb_bottom_front_left_enable": "true",
+            "multipcb_bottom_front_left_support": "front",
+            "multipcb_bottom_front_right_adjust": "0",
+            "multipcb_bottom_front_right_enable": "true",
+            "multipcb_bottom_front_right_support": "front",
+            "multipcb_bottom_rear_left_adjust": "0",
+            "multipcb_bottom_rear_left_enable": "true",
+            "multipcb_bottom_rear_left_support": "rear",
+            "multipcb_bottom_rear_right_adjust": "0",
+            "multipcb_bottom_rear_right_enable": "true",
+            "multipcb_bottom_rear_right_support": "rear",
+            "multipcb_bottom_sidewall_support": "false",
+            "multipcb_bottom_standoff_diameter": "5.75",
+            "multipcb_bottom_standoff_hole_size": "3.4",
+            "multipcb_bottom_standoff_insert": "false",
+            "multipcb_bottom_standoff_insert_dia": "4.2",
+            "multipcb_bottom_standoff_insert_height": "5.1",
+            "multipcb_bottom_standoff_pillar": "hex",
+            "multipcb_bottom_standoff_reverse": "false",
+            "multipcb_bottom_standoff_size": "m2.5",
+            "multipcb_bottom_standoff_support_height": "4",
+            "multipcb_bottom_standoff_support_size": "7",
+            "multipcb_bottom_standoff_type": "countersunk",
+            "multipcb_bottom_standoffs": "false",
+            "multipcb_top_front_left_adjust": "0",
+            "multipcb_top_front_left_enable": "true",
+            "multipcb_top_front_left_support": "front",
+            "multipcb_top_front_right_adjust": "0",
+            "multipcb_top_front_right_enable": "true",
+            "multipcb_top_front_right_support": "front",
+            "multipcb_top_rear_left_adjust": "0",
+            "multipcb_top_rear_left_enable": "true",
+            "multipcb_top_rear_left_support": "rear",
+            "multipcb_top_rear_right_adjust": "0",
+            "multipcb_top_rear_right_enable": "true",
+            "multipcb_top_rear_right_support": "rear",
+            "multipcb_top_sidewall_support": "false",
+            "multipcb_top_standoff_diameter": "5.75",
+            "multipcb_top_standoff_hole_size": "2.75",
+            "multipcb_top_standoff_insert": "false",
+            "multipcb_top_standoff_insert_dia": "4.2",
+            "multipcb_top_standoff_insert_height": "5.1",
+            "multipcb_top_standoff_pillar": "hex",
+            "multipcb_top_standoff_reverse": "true",
+            "multipcb_top_standoff_size": "m2.5",
+            "multipcb_top_standoff_support_height": "4",
+            "multipcb_top_standoff_support_size": "7",
+            "multipcb_top_standoff_type": "blind",
+            "multipcb_top_standoffs": "false",
+            "nas_sbc_location": "bottom",
+            "pcb_loc_x": "9",
+            "pcb_loc_y": "2",
+            "pcb_loc_z": "0",
+            "raise_top": "0",
+            "rear_cooling": "fan_hex",
+            "rear_dualfan_spacing": "6",
+            "rear_fan": "1",
+            "rear_fan_center": "false",
+            "rear_fan_position": "30",
+            "rear_fan_size": "60",
+            "rear_io_shield": "false",
+            "sbc_bottom_standoffs": "false",
+            "sbc_highlight": "false",
+            "sbc_information": "false",
+            "sbc_model": "m1",
+            "sbc_off": "false",
+            "sbc_top_standoffs": "false",
+            "sidethick": "4",
+            "standard_motherboard_thickness": "0",
+            "text_color": "Green",
+            "text_font": "Nimbus Mono PS",
+            "tol": "0.25",
+            "top_cover_pattern": "solid",
+            "top_front_left_adjust": "0",
+            "top_front_left_enable": "true",
+            "top_front_left_support": "front",
+            "top_front_right_adjust": "0",
+            "top_front_right_enable": "true",
+            "top_front_right_support": "front",
+            "top_rear_left_adjust": "0",
+            "top_rear_left_enable": "true",
+            "top_rear_left_support": "rear",
+            "top_rear_right_adjust": "0",
+            "top_rear_right_enable": "true",
+            "top_rear_right_support": "rear",
+            "top_sidewall_support": "false",
+            "top_standoff_diameter": "5.75",
+            "top_standoff_hole_size": "2.75",
+            "top_standoff_insert": "false",
+            "top_standoff_insert_dia": "4.2",
+            "top_standoff_insert_height": "5.1",
+            "top_standoff_pillar": "hex",
+            "top_standoff_reverse": "true",
+            "top_standoff_size": "m3",
+            "top_standoff_support_height": "4",
+            "top_standoff_support_size": "10",
+            "top_standoff_type": "countersunk",
+            "uart_opening": "none",
+            "view": "model",
+            "wallthick": "2"
+        },
         "m1s_shell_nvme": {
             "$fn": "90",
             "access_panel_location": "[0, 28]",
@@ -5017,223 +5234,6 @@
             "view": "model",
             "wallthick": "2"
         },
-        "h3_panel_nas": {
-            "$fn": "90",
-            "access_panel_location": "[10, 15]",
-            "access_panel_orientation": "landscape",
-            "access_panel_rotation": "0",
-            "access_panel_size": "[70, 30]",
-            "accessory_highlight": "false",
-            "accessory_name": "h3_panel_nas",
-            "adj": "0.01",
-            "bend_allowance": "1",
-            "bottom_access_panel_enable": "false",
-            "bottom_clearence": "3.5",
-            "bottom_cover_pattern": "solid",
-            "bottom_front_left_adjust": "0",
-            "bottom_front_left_enable": "true",
-            "bottom_front_left_support": "front",
-            "bottom_front_right_adjust": "0",
-            "bottom_front_right_enable": "true",
-            "bottom_front_right_support": "front",
-            "bottom_rear_left_adjust": "0",
-            "bottom_rear_left_enable": "true",
-            "bottom_rear_left_support": "rear",
-            "bottom_rear_right_adjust": "0",
-            "bottom_rear_right_enable": "true",
-            "bottom_rear_right_support": "rear",
-            "bottom_sidewall_support": "false",
-            "bottom_standoff_diameter": "5.75",
-            "bottom_standoff_hole_size": "3.4",
-            "bottom_standoff_insert": "false",
-            "bottom_standoff_insert_dia": "4.2",
-            "bottom_standoff_insert_height": "5.1",
-            "bottom_standoff_pillar": "hex",
-            "bottom_standoff_reverse": "false",
-            "bottom_standoff_size": "m3",
-            "bottom_standoff_support_height": "4",
-            "bottom_standoff_support_size": "10",
-            "bottom_standoff_type": "countersunk",
-            "case_design": "panel_nas",
-            "case_offset_bz": "0",
-            "case_offset_tz": "0",
-            "case_offset_x": "0",
-            "case_offset_y": "25",
-            "cooling": "fan_hex",
-            "corner_fillet": "3",
-            "edge_fillet": "0",
-            "ext_bottom_front_left_adjust": "0",
-            "ext_bottom_front_left_enable": "true",
-            "ext_bottom_front_left_support": "front",
-            "ext_bottom_front_right_adjust": "0",
-            "ext_bottom_front_right_enable": "true",
-            "ext_bottom_front_right_support": "front",
-            "ext_bottom_rear_left_adjust": "0",
-            "ext_bottom_rear_left_enable": "true",
-            "ext_bottom_rear_left_support": "rear",
-            "ext_bottom_rear_right_adjust": "0",
-            "ext_bottom_rear_right_enable": "true",
-            "ext_bottom_rear_right_support": "rear",
-            "ext_bottom_sidewall_support": "true",
-            "ext_bottom_standoff_diameter": "5.75",
-            "ext_bottom_standoff_hole_size": "3.4",
-            "ext_bottom_standoff_insert": "false",
-            "ext_bottom_standoff_insert_dia": "4.2",
-            "ext_bottom_standoff_insert_height": "5.1",
-            "ext_bottom_standoff_pillar": "hex",
-            "ext_bottom_standoff_reverse": "false",
-            "ext_bottom_standoff_size": "m3",
-            "ext_bottom_standoff_support_height": "4",
-            "ext_bottom_standoff_support_size": "10",
-            "ext_bottom_standoff_type": "countersunk",
-            "ext_bottom_standoffs": "false",
-            "ext_top_front_left_adjust": "0",
-            "ext_top_front_left_enable": "true",
-            "ext_top_front_left_support": "front",
-            "ext_top_front_right_adjust": "0",
-            "ext_top_front_right_enable": "true",
-            "ext_top_front_right_support": "front",
-            "ext_top_rear_left_adjust": "0",
-            "ext_top_rear_left_enable": "true",
-            "ext_top_rear_left_support": "rear",
-            "ext_top_rear_right_adjust": "0",
-            "ext_top_rear_right_enable": "true",
-            "ext_top_rear_right_support": "rear",
-            "ext_top_sidewall_support": "true",
-            "ext_top_standoff_diameter": "5.75",
-            "ext_top_standoff_hole_size": "2.75",
-            "ext_top_standoff_insert": "false",
-            "ext_top_standoff_insert_dia": "4.2",
-            "ext_top_standoff_insert_height": "5.1",
-            "ext_top_standoff_pillar": "hex",
-            "ext_top_standoff_reverse": "true",
-            "ext_top_standoff_size": "m3",
-            "ext_top_standoff_support_height": "4",
-            "ext_top_standoff_support_size": "10",
-            "ext_top_standoff_type": "blind",
-            "ext_top_standoffs": "false",
-            "fan_size": "80",
-            "flat_blank_section": "false",
-            "floorthick": "3",
-            "front_cover_pattern": "hex_5mm",
-            "gap": "1",
-            "gpio_opening": "none",
-            "hd_bays": "2",
-            "hd_center": "false",
-            "hd_reverse": "true",
-            "hd_space": "10",
-            "hd_y_position": "20",
-            "hd_z_position": "7",
-            "indents": "false",
-            "individual_part": "bottom",
-            "lower_bottom": "0",
-            "material_thickness": "0.5",
-            "move_front": "0",
-            "move_leftside": "0",
-            "move_rear": "0",
-            "move_rightside": "0",
-            "multipcb_bottom_front_left_adjust": "0",
-            "multipcb_bottom_front_left_enable": "true",
-            "multipcb_bottom_front_left_support": "front",
-            "multipcb_bottom_front_right_adjust": "0",
-            "multipcb_bottom_front_right_enable": "true",
-            "multipcb_bottom_front_right_support": "front",
-            "multipcb_bottom_rear_left_adjust": "0",
-            "multipcb_bottom_rear_left_enable": "true",
-            "multipcb_bottom_rear_left_support": "rear",
-            "multipcb_bottom_rear_right_adjust": "0",
-            "multipcb_bottom_rear_right_enable": "true",
-            "multipcb_bottom_rear_right_support": "rear",
-            "multipcb_bottom_sidewall_support": "false",
-            "multipcb_bottom_standoff_diameter": "5.75",
-            "multipcb_bottom_standoff_hole_size": "3.4",
-            "multipcb_bottom_standoff_insert": "false",
-            "multipcb_bottom_standoff_insert_dia": "4.2",
-            "multipcb_bottom_standoff_insert_height": "5.1",
-            "multipcb_bottom_standoff_pillar": "hex",
-            "multipcb_bottom_standoff_reverse": "false",
-            "multipcb_bottom_standoff_size": "m2.5",
-            "multipcb_bottom_standoff_support_height": "4",
-            "multipcb_bottom_standoff_support_size": "7",
-            "multipcb_bottom_standoff_type": "countersunk",
-            "multipcb_bottom_standoffs": "false",
-            "multipcb_top_front_left_adjust": "0",
-            "multipcb_top_front_left_enable": "true",
-            "multipcb_top_front_left_support": "front",
-            "multipcb_top_front_right_adjust": "0",
-            "multipcb_top_front_right_enable": "true",
-            "multipcb_top_front_right_support": "front",
-            "multipcb_top_rear_left_adjust": "0",
-            "multipcb_top_rear_left_enable": "true",
-            "multipcb_top_rear_left_support": "rear",
-            "multipcb_top_rear_right_adjust": "0",
-            "multipcb_top_rear_right_enable": "true",
-            "multipcb_top_rear_right_support": "rear",
-            "multipcb_top_sidewall_support": "false",
-            "multipcb_top_standoff_diameter": "5.75",
-            "multipcb_top_standoff_hole_size": "2.75",
-            "multipcb_top_standoff_insert": "false",
-            "multipcb_top_standoff_insert_dia": "4.2",
-            "multipcb_top_standoff_insert_height": "5.1",
-            "multipcb_top_standoff_pillar": "hex",
-            "multipcb_top_standoff_reverse": "true",
-            "multipcb_top_standoff_size": "m2.5",
-            "multipcb_top_standoff_support_height": "4",
-            "multipcb_top_standoff_support_size": "7",
-            "multipcb_top_standoff_type": "blind",
-            "multipcb_top_standoffs": "false",
-            "nas_sbc_location": "top",
-            "pcb_loc_x": "0",
-            "pcb_loc_y": "0",
-            "pcb_loc_z": "0",
-            "raise_top": "0",
-            "rear_cooling": "fan_hex",
-            "rear_dualfan_spacing": "6",
-            "rear_fan": "1",
-            "rear_fan_center": "false",
-            "rear_fan_position": "4",
-            "rear_fan_size": "80",
-            "rear_io_shield": "false",
-            "sbc_bottom_standoffs": "false",
-            "sbc_highlight": "false",
-            "sbc_information": "false",
-            "sbc_model": "h3+",
-            "sbc_off": "false",
-            "sbc_top_standoffs": "true",
-            "sidethick": "4",
-            "standard_motherboard_thickness": "0",
-            "text_color": "Green",
-            "text_font": "Nimbus Mono PS",
-            "tol": "0.25",
-            "top_cover_pattern": "solid",
-            "top_front_left_adjust": "0",
-            "top_front_left_enable": "true",
-            "top_front_left_support": "front",
-            "top_front_right_adjust": "0",
-            "top_front_right_enable": "true",
-            "top_front_right_support": "front",
-            "top_rear_left_adjust": "0",
-            "top_rear_left_enable": "true",
-            "top_rear_left_support": "rear",
-            "top_rear_right_adjust": "0",
-            "top_rear_right_enable": "true",
-            "top_rear_right_support": "rear",
-            "top_sidewall_support": "false",
-            "top_standoff_diameter": "5.75",
-            "top_standoff_hole_size": "2.75",
-            "top_standoff_insert": "false",
-            "top_standoff_insert_dia": "4.2",
-            "top_standoff_insert_height": "5.1",
-            "top_standoff_pillar": "hex",
-            "top_standoff_reverse": "true",
-            "top_standoff_size": "m3",
-            "top_standoff_support_height": "25",
-            "top_standoff_support_size": "10",
-            "top_standoff_type": "recessed",
-            "uart_opening": "default",
-            "view": "model",
-            "wallthick": "3"
-        },
         "h3_ultimate": {
             "$fn": "90",
             "access_panel_location": "[5, 30]",
@@ -5540,6 +5540,223 @@
             "view": "model",
             "wallthick": "2.5"
         },
+        "h3_panel_nas": {
+            "$fn": "90",
+            "access_panel_location": "[10, 15]",
+            "access_panel_orientation": "landscape",
+            "access_panel_rotation": "0",
+            "access_panel_size": "[70, 30]",
+            "accessory_highlight": "false",
+            "accessory_name": "h3_panel_nas",
+            "adj": "0.01",
+            "bend_allowance": "1",
+            "bottom_access_panel_enable": "false",
+            "bottom_clearence": "3.5",
+            "bottom_cover_pattern": "solid",
+            "bottom_front_left_adjust": "0",
+            "bottom_front_left_enable": "true",
+            "bottom_front_left_support": "front",
+            "bottom_front_right_adjust": "0",
+            "bottom_front_right_enable": "true",
+            "bottom_front_right_support": "front",
+            "bottom_rear_left_adjust": "0",
+            "bottom_rear_left_enable": "true",
+            "bottom_rear_left_support": "rear",
+            "bottom_rear_right_adjust": "0",
+            "bottom_rear_right_enable": "true",
+            "bottom_rear_right_support": "rear",
+            "bottom_sidewall_support": "false",
+            "bottom_standoff_diameter": "5.75",
+            "bottom_standoff_hole_size": "3.4",
+            "bottom_standoff_insert": "false",
+            "bottom_standoff_insert_dia": "4.2",
+            "bottom_standoff_insert_height": "5.1",
+            "bottom_standoff_pillar": "hex",
+            "bottom_standoff_reverse": "false",
+            "bottom_standoff_size": "m3",
+            "bottom_standoff_support_height": "4",
+            "bottom_standoff_support_size": "10",
+            "bottom_standoff_type": "countersunk",
+            "case_design": "panel_nas",
+            "case_offset_bz": "0",
+            "case_offset_tz": "0",
+            "case_offset_x": "0",
+            "case_offset_y": "25",
+            "cooling": "fan_hex",
+            "corner_fillet": "3",
+            "edge_fillet": "0",
+            "ext_bottom_front_left_adjust": "0",
+            "ext_bottom_front_left_enable": "true",
+            "ext_bottom_front_left_support": "front",
+            "ext_bottom_front_right_adjust": "0",
+            "ext_bottom_front_right_enable": "true",
+            "ext_bottom_front_right_support": "front",
+            "ext_bottom_rear_left_adjust": "0",
+            "ext_bottom_rear_left_enable": "true",
+            "ext_bottom_rear_left_support": "rear",
+            "ext_bottom_rear_right_adjust": "0",
+            "ext_bottom_rear_right_enable": "true",
+            "ext_bottom_rear_right_support": "rear",
+            "ext_bottom_sidewall_support": "true",
+            "ext_bottom_standoff_diameter": "5.75",
+            "ext_bottom_standoff_hole_size": "3.4",
+            "ext_bottom_standoff_insert": "false",
+            "ext_bottom_standoff_insert_dia": "4.2",
+            "ext_bottom_standoff_insert_height": "5.1",
+            "ext_bottom_standoff_pillar": "hex",
+            "ext_bottom_standoff_reverse": "false",
+            "ext_bottom_standoff_size": "m3",
+            "ext_bottom_standoff_support_height": "4",
+            "ext_bottom_standoff_support_size": "10",
+            "ext_bottom_standoff_type": "countersunk",
+            "ext_bottom_standoffs": "false",
+            "ext_top_front_left_adjust": "0",
+            "ext_top_front_left_enable": "true",
+            "ext_top_front_left_support": "front",
+            "ext_top_front_right_adjust": "0",
+            "ext_top_front_right_enable": "true",
+            "ext_top_front_right_support": "front",
+            "ext_top_rear_left_adjust": "0",
+            "ext_top_rear_left_enable": "true",
+            "ext_top_rear_left_support": "rear",
+            "ext_top_rear_right_adjust": "0",
+            "ext_top_rear_right_enable": "true",
+            "ext_top_rear_right_support": "rear",
+            "ext_top_sidewall_support": "true",
+            "ext_top_standoff_diameter": "5.75",
+            "ext_top_standoff_hole_size": "2.75",
+            "ext_top_standoff_insert": "false",
+            "ext_top_standoff_insert_dia": "4.2",
+            "ext_top_standoff_insert_height": "5.1",
+            "ext_top_standoff_pillar": "hex",
+            "ext_top_standoff_reverse": "true",
+            "ext_top_standoff_size": "m3",
+            "ext_top_standoff_support_height": "4",
+            "ext_top_standoff_support_size": "10",
+            "ext_top_standoff_type": "blind",
+            "ext_top_standoffs": "false",
+            "fan_size": "80",
+            "flat_blank_section": "false",
+            "floorthick": "3",
+            "front_cover_pattern": "hex_5mm",
+            "gap": "1",
+            "gpio_opening": "none",
+            "hd_bays": "2",
+            "hd_center": "false",
+            "hd_reverse": "true",
+            "hd_space": "10",
+            "hd_y_position": "20",
+            "hd_z_position": "10",
+            "indents": "false",
+            "individual_part": "bottom",
+            "lower_bottom": "0",
+            "material_thickness": "0.5",
+            "move_front": "0",
+            "move_leftside": "0",
+            "move_rear": "0",
+            "move_rightside": "0",
+            "multipcb_bottom_front_left_adjust": "0",
+            "multipcb_bottom_front_left_enable": "true",
+            "multipcb_bottom_front_left_support": "front",
+            "multipcb_bottom_front_right_adjust": "0",
+            "multipcb_bottom_front_right_enable": "true",
+            "multipcb_bottom_front_right_support": "front",
+            "multipcb_bottom_rear_left_adjust": "0",
+            "multipcb_bottom_rear_left_enable": "true",
+            "multipcb_bottom_rear_left_support": "rear",
+            "multipcb_bottom_rear_right_adjust": "0",
+            "multipcb_bottom_rear_right_enable": "true",
+            "multipcb_bottom_rear_right_support": "rear",
+            "multipcb_bottom_sidewall_support": "false",
+            "multipcb_bottom_standoff_diameter": "5.75",
+            "multipcb_bottom_standoff_hole_size": "3.4",
+            "multipcb_bottom_standoff_insert": "false",
+            "multipcb_bottom_standoff_insert_dia": "4.2",
+            "multipcb_bottom_standoff_insert_height": "5.1",
+            "multipcb_bottom_standoff_pillar": "hex",
+            "multipcb_bottom_standoff_reverse": "false",
+            "multipcb_bottom_standoff_size": "m2.5",
+            "multipcb_bottom_standoff_support_height": "4",
+            "multipcb_bottom_standoff_support_size": "7",
+            "multipcb_bottom_standoff_type": "countersunk",
+            "multipcb_bottom_standoffs": "false",
+            "multipcb_top_front_left_adjust": "0",
+            "multipcb_top_front_left_enable": "true",
+            "multipcb_top_front_left_support": "front",
+            "multipcb_top_front_right_adjust": "0",
+            "multipcb_top_front_right_enable": "true",
+            "multipcb_top_front_right_support": "front",
+            "multipcb_top_rear_left_adjust": "0",
+            "multipcb_top_rear_left_enable": "true",
+            "multipcb_top_rear_left_support": "rear",
+            "multipcb_top_rear_right_adjust": "0",
+            "multipcb_top_rear_right_enable": "true",
+            "multipcb_top_rear_right_support": "rear",
+            "multipcb_top_sidewall_support": "false",
+            "multipcb_top_standoff_diameter": "5.75",
+            "multipcb_top_standoff_hole_size": "2.75",
+            "multipcb_top_standoff_insert": "false",
+            "multipcb_top_standoff_insert_dia": "4.2",
+            "multipcb_top_standoff_insert_height": "5.1",
+            "multipcb_top_standoff_pillar": "hex",
+            "multipcb_top_standoff_reverse": "true",
+            "multipcb_top_standoff_size": "m2.5",
+            "multipcb_top_standoff_support_height": "4",
+            "multipcb_top_standoff_support_size": "7",
+            "multipcb_top_standoff_type": "blind",
+            "multipcb_top_standoffs": "false",
+            "nas_sbc_location": "top",
+            "pcb_loc_x": "0",
+            "pcb_loc_y": "0",
+            "pcb_loc_z": "0",
+            "raise_top": "0",
+            "rear_cooling": "fan_hex",
+            "rear_dualfan_spacing": "6",
+            "rear_fan": "1",
+            "rear_fan_center": "false",
+            "rear_fan_position": "4",
+            "rear_fan_size": "80",
+            "rear_io_shield": "false",
+            "sbc_bottom_standoffs": "false",
+            "sbc_highlight": "false",
+            "sbc_information": "false",
+            "sbc_model": "h3+",
+            "sbc_off": "false",
+            "sbc_top_standoffs": "true",
+            "sidethick": "4",
+            "standard_motherboard_thickness": "0",
+            "text_color": "Green",
+            "text_font": "Nimbus Mono PS",
+            "tol": "0.25",
+            "top_cover_pattern": "solid",
+            "top_front_left_adjust": "0",
+            "top_front_left_enable": "true",
+            "top_front_left_support": "front",
+            "top_front_right_adjust": "0",
+            "top_front_right_enable": "true",
+            "top_front_right_support": "front",
+            "top_rear_left_adjust": "0",
+            "top_rear_left_enable": "true",
+            "top_rear_left_support": "rear",
+            "top_rear_right_adjust": "0",
+            "top_rear_right_enable": "true",
+            "top_rear_right_support": "rear",
+            "top_sidewall_support": "false",
+            "top_standoff_diameter": "5.75",
+            "top_standoff_hole_size": "2.75",
+            "top_standoff_insert": "false",
+            "top_standoff_insert_dia": "4.2",
+            "top_standoff_insert_height": "5.1",
+            "top_standoff_pillar": "hex",
+            "top_standoff_reverse": "true",
+            "top_standoff_size": "m3",
+            "top_standoff_support_height": "25",
+            "top_standoff_support_size": "10",
+            "top_standoff_type": "recessed",
+            "uart_opening": "default",
+            "view": "model",
+            "wallthick": "3"
+        },
         "h4_panel_nas": {
             "$fn": "90",
             "access_panel_location": "[10, 15]",
diff --git a/sbc_case_builder.scad b/sbc_case_builder.scad
index bf42770..e47b616 100644
--- a/sbc_case_builder.scad
+++ b/sbc_case_builder.scad
@@ -83,9 +83,9 @@ case_offset_x = 0; //[0:.01:300]
 // additional y axis case size
 case_offset_y = 0; //[0:.01:300]
 // additional z axis case top size
-case_offset_tz = 0; //[-30:.01:300]
+case_offset_tz = 0; //[-50:.01:300]
 // additional z axis case bottom size
-case_offset_bz = 0; //[0:.01:300]
+case_offset_bz = 0; //[-50:.01:300]
 // case wall thickness
 wallthick = 2; //[1:.25:5]
 // case floor and ceiling thickness
@@ -497,7 +497,7 @@ if (view == "platter") {
         translate([-20,0,-gap]) rotate([0,90,90]) 
             case_side(case_design,"left");
         // nas hd spacers
-        if(case_design == "panel_nas" && (pcb_width > 100 || width > 101.6)) {
+        if(case_design == "panel_nas" && (pcb_width > 100 || width > 112)) {
             if(hd_center == false) {
                 translate([0,-35,0]) rotate([270,0,0]) cableholder_spacer(hd_spacer-9.4);
             }
@@ -699,7 +699,7 @@ if (view == "model") {
                     if(hd_center == false) {
                         translate([-gap,-(3*wallthick)-gap+hd_y_position,hd_z_position+(hd_space+27.1)*i]) 
                             hd35("portrait", [false,0,0,"default"]);
-                        if(pcb_width > 100 || width > 101.6) {
+                        if(pcb_width > 100 || width-2*(sidethick+gap) > 101.6) {
                             translate([101.6-gap+hd_spacer-9.4,
                                 28.5-(3*wallthick)-gap+hd_y_position+101.6,
                                     hd_z_position+6+(hd_space+27.1)*i]) 
@@ -720,7 +720,7 @@ if (view == "model") {
                         translate([-gap+hd_spacer/2,
                             -(3*wallthick)-gap+hd_y_position,hd_z_position+(hd_space+27.1)*i]) 
                                 hd35("portrait", [false,0,0,"default"]);
-                        if(pcb_width > 100 || width > 101.6) {
+                        if(pcb_width > 100 || width-2*(sidethick+gap) > 101.6) {
                             // right side spacers
                             translate([101.6-gap+hd_spacer-9.4,
                                 28.5-(3*wallthick)-gap+hd_y_position+101.6,
@@ -759,7 +759,7 @@ if (view == "model") {
                         translate([101.6-gap,-(3*wallthick)-gap+hd_y_position+147,
                             hd_z_position+(hd_space+27.1)*i]) 
                                 rotate([0,0,180]) hd35("portrait", [false,0,0,"default"]);
-                        if(pcb_width > 100 || width > 101.6) {
+                        if(pcb_width > 100 || width-2*(sidethick+gap) > 101.6) {
                             translate([101.6-gap+hd_spacer-9.4,
                                 17-(3*wallthick)-gap+hd_y_position+101.6,
                                     hd_z_position+6.5+(hd_space+27.1)*i]) 
@@ -780,7 +780,7 @@ if (view == "model") {
                             -(3*wallthick)-gap+hd_y_position+147,
                                 hd_z_position+(hd_space+27.1)*i]) 
                                     rotate([0,0,180]) hd35("portrait", [false,0,0,"default"]);
-                        if(pcb_width > 100 || width > 101.6) {
+                        if(pcb_width > 100 || width-2*(sidethick+gap) > 101.6) {
                             // right side spacers
                             translate([101.6-gap+hd_spacer-9.4,
                                 17-(3*wallthick)-gap+hd_y_position+101.6,
diff --git a/sbc_case_builder_accessories.cfg b/sbc_case_builder_accessories.cfg
index f733bcb..7a7e177 100644
--- a/sbc_case_builder_accessories.cfg
+++ b/sbc_case_builder_accessories.cfg
@@ -468,7 +468,7 @@ accessory_data = [
 
      // Odroid-H4
      ["h4_panel_nas",
-     "model","hk_pwr_button",20,175,206,"top",[0,0,0],["sbc-case_z",true,true,true],[0,0,0],[0],[true,10,2,"default"]],
+     "model","hk_pwr_button",20,175,206,"top",[0,0,0],["case",true,true,true],[0,0,0],[0],[true,10,2,"default"]],
 
      ["show2_shell",
      "model","hk_wb2",6.25,24.675,16,"bottom",[0,0,180],["sbc",true,true,true],[0,0,0],[0],[false,10,2,"default"],