Adjusted Tronxy X5s settings

Signed-off-by: Arkadiusz Gluszyk <agluszyk@cs.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

config/printer-tronxy-x5s-2018.cfg

@@ -0,0 +1,100 @@
+# This file contains pin mappings for the Tronxy X5S (circa 2017). To
+# use this config, the firmware should be compiled for the AVR
+# atmega1284p.
+
+# UPDATE 2018
+# Newest Tronxy's are coming with bootloader present, so follow
+# klipper install instructions but instead of "make flash FLASH_DEVICE=/dev/ttyACM0"
+# use:
+# avrdude -p atmega1284p -c arduino -b 57600 -P /dev/ttyUSB0 -U out/klipper.elf.hex
+
+# Note, a number of Melzi boards are shipped without a bootloader. In
+# that case, an external programmer will be needed to flash a
+# bootloader to the board (for example, see
+# http://www.instructables.com/id/Flashing-a-Bootloader-to-the-CR-10/
+# ). Once that is done, one should be able to use the standard "make
+# flash" command to flash Klipper.
+
+# See the example.cfg file for a description of available parameters.
+
+[stepper_x]
+step_pin: PD7
+dir_pin: !PC5
+enable_pin: !PD6
+step_distance: .0125
+endstop_pin: ^!PC2
+position_endstop: 0
+position_max: 330
+homing_speed: 50
+
+[stepper_y]
+step_pin: PC6
+dir_pin: !PC7
+enable_pin: !PD6
+step_distance: .0125
+endstop_pin: ^!PC3
+position_endstop: 0
+position_max: 310
+homing_speed: 50
+
+[stepper_z]
+step_pin: PB3
+dir_pin: PB2
+enable_pin: !PD6
+step_distance: .0025
+endstop_pin: ^!PC4
+position_endstop: 0.5
+position_max: 400
+
+[extruder]
+step_pin: PB1
+dir_pin: PB0
+enable_pin: !PD6
+step_distance: .0111
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PD5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PA7
+control: pid
+pid_Kp: 22.2
+pid_Ki: 1.08
+pid_Kd: 114
+min_temp: 0
+max_temp: 275
+
+[heater_bed]
+heater_pin: PD4
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PA6
+control: watermark
+min_temp: 0
+max_temp: 150
+
+[verify_heater heater_bed]
+# adjust for personal bed setup, this prevents stock heated bed from issuing
+# false positive heating errors due to slow temperature increase
+check_gain_time: 600
+
+[fan]
+pin: PB4
+
+[mcu]
+serial: /dev/ttyUSB0
+
+[printer]
+kinematics: corexy
+max_velocity: 300
+max_accel: 1000
+max_z_velocity: 20
+max_z_accel: 100
+
+[display]
+lcd_type: st7920
+cs_pin: PA1
+sclk_pin: PC0
+sid_pin: PA3
+
+# buttons are:
+# PD2, PD3: encoder
+# PA5: click