mirror of
git://soft.sys114.com/klipper
synced 2026-02-04 13:10:36 +09:00
262 lines
4.9 KiB
INI
262 lines
4.9 KiB
INI
# Copyright (C) 2025 Hardkernel Co., Ltd
|
|
#
|
|
# This program is free software: you can redistribute it and/or modify
|
|
# it under the terms of the GNU General Public License as published by
|
|
# the Free Software Foundation, either version 3 of the License, or
|
|
# (at your option) any later version.
|
|
#
|
|
# This program is distributed in the hope that it will be useful,
|
|
# but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
# GNU General Public License for more details.
|
|
#
|
|
# You should have received a copy of the GNU General Public License
|
|
# along with this program. If not, see <http://www.gnu.org/licenses/>
|
|
|
|
# This file contains common pin mappings for the m1s with board_stepper
|
|
# To use this config, the firmware should be compiled for the
|
|
# Linux process.
|
|
|
|
[mcu]
|
|
serial: /tmp/klipper_host_mcu
|
|
|
|
[mcu EBBCan] # based on EBB42 CAN V1.0
|
|
canbus_uuid: 1e8ea3b32c8a
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 500
|
|
max_accel: 5000
|
|
#max_accel: 7000
|
|
#max_accel_to_decel: 3500
|
|
max_z_velocity: 25
|
|
max_z_accel: 100
|
|
|
|
[stepper_x]
|
|
step_pin: gpiochip0/gpio31
|
|
dir_pin: gpiochip0/gpio30
|
|
enable_pin: !gpiochip0/gpio50
|
|
endstop_pin: gpiochip0/gpio51
|
|
homing_retract_dist: 2
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: gpiochip0/gpio28
|
|
dir_pin: gpiochip0/gpio41
|
|
enable_pin: !gpiochip0/gpio66
|
|
endstop_pin: gpiochip0/gpio49
|
|
homing_retract_dist: 2
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: gpiochip0/gpio55
|
|
dir_pin: !gpiochip0/gpio62
|
|
enable_pin: !gpiochip0/gpio26
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: probe: z_virtual_endstop
|
|
position_min: -4.0
|
|
position_max: 300
|
|
|
|
[stepper_z1]
|
|
step_pin: gpiochip0/gpio54
|
|
dir_pin: !gpiochip0/gpio40
|
|
enable_pin: !gpiochip0/gpio27
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
|
|
[extruder]
|
|
step_pin: EBBCan: PA9
|
|
dir_pin: EBBCan: PA8
|
|
enable_pin: !EBBCan: PA10
|
|
microsteps: 16
|
|
rotation_distance: 7.703694208
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: EBBCan:PB1
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: EBBCan:PA0
|
|
control: pid
|
|
pid_Kp: 21.527
|
|
pid_Ki: 1.063
|
|
pid_Kd: 108.982
|
|
min_temp: 0
|
|
max_temp: 240
|
|
min_extrude_temp: 0
|
|
|
|
[heater_fan nozzle_fan]
|
|
pin: EBBCan:PA2
|
|
heater: extruder
|
|
heater_temp: 50.0
|
|
|
|
[heater_bed]
|
|
heater_pin: gpiochip0/gpio65
|
|
sensor_type: ATC Semitec 104GT-2
|
|
sensor_pin: analog0
|
|
control: pid
|
|
pid_Kp: 21.527
|
|
pid_Ki: 1.063
|
|
pid_Kd: 108.982
|
|
min_temp: 0
|
|
max_temp: 85
|
|
|
|
[z_tilt]
|
|
z_positions:
|
|
260, 130# -55,-7
|
|
-30, 130# -55,320
|
|
points:
|
|
20,130
|
|
180,130
|
|
retries: 5
|
|
retry_tolerance: 0.002
|
|
|
|
[fan]
|
|
pin: EBBCan:PA1
|
|
|
|
[verify_heater extruder]
|
|
max_error: 200
|
|
check_gain_time: 60
|
|
heating_gain: 1
|
|
|
|
[tmc2209 stepper_x]
|
|
uart_pin: gpiochip0/gpio61
|
|
tx_pin: gpiochip0/gpio60
|
|
uart_address: 1
|
|
run_current: 0.800
|
|
hold_current: 0.500
|
|
stealthchop_threshold: 250
|
|
|
|
[tmc2209 stepper_y]
|
|
uart_pin: gpiochip0/gpio61
|
|
tx_pin: gpiochip0/gpio60
|
|
uart_address: 2
|
|
run_current: 0.800
|
|
hold_current: 0.500
|
|
stealthchop_threshold: 250
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: gpiochip0/gpio61
|
|
tx_pin: gpiochip0/gpio60
|
|
uart_address: 3
|
|
run_current: 1.000
|
|
hold_current: 0.500
|
|
stealthchop_threshold: 30
|
|
|
|
[tmc2209 stepper_z1]
|
|
uart_pin: gpiochip0/gpio61
|
|
tx_pin: gpiochip0/gpio60
|
|
uart_address: 0
|
|
run_current: 1.000
|
|
hold_current: 0.500
|
|
stealthchop_threshold: 30
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: EBBCan:PA13
|
|
run_current: 0.800
|
|
hold_current: 0.500
|
|
stealthchop_threshold: 250
|
|
|
|
[probe]
|
|
pin: !EBBCan:PA5
|
|
x_offset: -42.0
|
|
y_offset: -4.0
|
|
speed: 5.0
|
|
|
|
[bed_mesh]
|
|
speed: 80
|
|
mesh_min: 0,0
|
|
mesh_max: 150,150
|
|
probe_count: 5,5
|
|
|
|
[bed_screws]
|
|
screw1: 30,25
|
|
screw2: 200,25
|
|
screw3: 200,200
|
|
screw4: 30, 200
|
|
|
|
[input_shaper]
|
|
shaper_freq_x: 39.4
|
|
shaper_type_x: mzv
|
|
shaper_freq_y: 25.0
|
|
shaper_type_y: mzv
|
|
|
|
[virtual_sdcard]
|
|
path: /var/printer_data/gcodes
|
|
|
|
[pause_resume]
|
|
|
|
[display_status]
|
|
|
|
[homing_override]
|
|
set_position_z: 0
|
|
axes: z
|
|
gcode:
|
|
G1 Z10 F600
|
|
G28 X Y
|
|
G1 X142 Y150 F3000 # (100 + 42, 150 + 4)
|
|
G28 Z
|
|
|
|
[gcode_macro PRINT_END]
|
|
gcode:
|
|
# Move Z +25
|
|
SAVE_GCODE_STATE NAME=_ui_movement
|
|
G91
|
|
G1 Z+25 F1500
|
|
RESTORE_GCODE_STATE NAME=_ui_movement
|
|
|
|
# Retract filament
|
|
SAVE_GCODE_STATE NAME=_ui_extrude
|
|
M83
|
|
G1 E-5 F300
|
|
RESTORE_GCODE_STATE NAME=_ui_extrude
|
|
|
|
# Move X and Y to 0
|
|
G28 X
|
|
G28 Y
|
|
|
|
[gcode_macro START_PRINT]
|
|
gcode:
|
|
G28
|
|
|
|
[gcode_macro PAUSE]
|
|
rename_existing: BASE_PAUSE
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=PAUSE_state
|
|
BASE_PAUSE
|
|
G91
|
|
G1 E-{E} F2100
|
|
G1 Z{Z}
|
|
G90
|
|
G1 X{X} Y{Y} F6000
|
|
|
|
[gcode_macro RESUME]
|
|
rename_existing: BASE_RESUME
|
|
gcode:
|
|
G91
|
|
G1 E{E} F2100
|
|
G90
|
|
RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1
|
|
BASE_RESUME
|
|
|
|
[gcode_macro CANCEL_PRINT]
|
|
rename_existing: BASE_CANCEL_PRINT
|
|
gcode:
|
|
TURN_OFF_HEATERS
|
|
CLEAR_PAUSE
|
|
SDCARD_RESET_FILE
|
|
BASE_CANCEL_PRINT
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [probe]
|
|
#*# z_offset = 0.34
|