Merge 5.15.121 into android14-5.15-lts

Changes in 5.15.121 netfilter: nf_tables: drop map element references from preparation phase fs: pipe: reveal missing function protoypes x86/resctrl: Only show tasks' pid in current pid namespace blk-iocost: use spin_lock_irqsave in adjust_inuse_and_calc_cost md/raid10: check slab-out-of-bounds in md_bitmap_get_counter md/raid10: fix overflow of md/safe_mode_delay md/raid10: fix wrong setting of max_corr_read_errors md/raid10: fix null-ptr-deref of mreplace in raid10_sync_request md/raid10: fix io loss while replacement replace rdev irqchip/jcore-aic: Fix missing allocation of IRQ descriptors svcrdma: Prevent page release when nothing was received posix-timers: Prevent RT livelock in itimer_delete() tracing/timer: Add missing hrtimer modes to decode_hrtimer_mode(). clocksource/drivers/cadence-ttc: Fix memory leak in ttc_timer_probe PM: domains: fix integer overflow issues in genpd_parse_state() perf/arm-cmn: Fix DTC reset powercap: RAPL: Fix CONFIG_IOSF_MBI dependency ARM: 9303/1: kprobes: avoid missing-declaration warnings cpufreq: intel_pstate: Fix energy_performance_preference for passive thermal/drivers/sun8i: Fix some error handling paths in sun8i_ths_probe() rcutorture: Correct name of use_softirq module parameter rcuscale: Always log error message rcuscale: Move shutdown from wait_event() to wait_event_idle() rcu/rcuscale: Move rcu_scale_*() after kfree_scale_cleanup() rcu/rcuscale: Stop kfree_scale_thread thread(s) after unloading rcuscale kselftest: vDSO: Fix accumulation of uninitialized ret when CLOCK_REALTIME is undefined perf/ibs: Fix interface via core pmu events x86/mm: Fix __swp_entry_to_pte() for Xen PV guests locking/atomic: arm: fix sync ops evm: Complete description of evm_inode_setattr() evm: Fix build warnings ima: Fix build warnings pstore/ram: Add check for kstrdup igc: Enable and fix RX hash usage by netstack wifi: ath9k: fix AR9003 mac hardware hang check register offset calculation wifi: ath9k: avoid referencing uninit memory in ath9k_wmi_ctrl_rx libbpf: btf_dump_type_data_check_overflow needs to consider BTF_MEMBER_BITFIELD_SIZE samples/bpf: Fix buffer overflow in tcp_basertt spi: spi-geni-qcom: Correct CS_TOGGLE bit in SPI_TRANS_CFG wifi: wilc1000: fix for absent RSN capabilities WFA testcase wifi: mwifiex: Fix the size of a memory allocation in mwifiex_ret_802_11_scan() sctp: add bpf_bypass_getsockopt proto callback libbpf: fix offsetof() and container_of() to work with CO-RE bpf: Don't EFAULT for {g,s}setsockopt with wrong optlen spi: dw: Round of n_bytes to power of 2 nfc: llcp: fix possible use of uninitialized variable in nfc_llcp_send_connect() bpftool: JIT limited misreported as negative value on aarch64 regulator: core: Fix more error checking for debugfs_create_dir() regulator: core: Streamline debugfs operations wifi: orinoco: Fix an error handling path in spectrum_cs_probe() wifi: orinoco: Fix an error handling path in orinoco_cs_probe() wifi: atmel: Fix an error handling path in atmel_probe() wl3501_cs: use eth_hw_addr_set() wifi: wl3501_cs: Fix an error handling path in wl3501_probe() wifi: ray_cs: Utilize strnlen() in parse_addr() wifi: ray_cs: Drop useless status variable in parse_addr() wifi: ray_cs: Fix an error handling path in ray_probe() wifi: ath9k: don't allow to overwrite ENDPOINT0 attributes selftests/bpf: Fix check_mtu using wrong variable type wifi: rsi: Do not configure WoWlan in shutdown hook if not enabled wifi: rsi: Do not set MMC_PM_KEEP_POWER in shutdown watchdog/perf: define dummy watchdog_update_hrtimer_threshold() on correct config watchdog/perf: more properly prevent false positives with turbo modes kexec: fix a memory leak in crash_shrink_memory() memstick r592: make memstick_debug_get_tpc_name() static wifi: ath9k: Fix possible stall on ath9k_txq_list_has_key() rtnetlink: extend RTEXT_FILTER_SKIP_STATS to IFLA_VF_INFO wifi: iwlwifi: pull from TXQs with softirqs disabled iwlwifi: don't dump_stack() when we get an unexpected interrupt wifi: iwlwifi: pcie: fix NULL pointer dereference in iwl_pcie_irq_rx_msix_handler() wifi: cfg80211: rewrite merging of inherited elements wifi: iwlwifi: mvm: indicate HW decrypt for beacon protection wifi: ath9k: convert msecs to jiffies where needed bpf: Omit superfluous address family check in __bpf_skc_lookup bpf: Factor out socket lookup functions for the TC hookpoint. bpf: Call __bpf_sk_lookup()/__bpf_skc_lookup() directly via TC hookpoint bpf: Fix bpf socket lookup from tc/xdp to respect socket VRF bindings can: length: fix bitstuffing count igc: Fix race condition in PTP tx code net: stmmac: fix double serdes powerdown netlink: fix potential deadlock in netlink_set_err() netlink: do not hard code device address lenth in fdb dumps bonding: do not assume skb mac_header is set selftests: rtnetlink: remove netdevsim device after ipsec offload test gtp: Fix use-after-free in __gtp_encap_destroy(). net: axienet: Move reset before 64-bit DMA detection sfc: fix crash when reading stats while NIC is resetting nfc: llcp: simplify llcp_sock_connect() error paths net: nfc: Fix use-after-free caused by nfc_llcp_find_local lib/ts_bm: reset initial match offset for every block of text netfilter: conntrack: dccp: copy entire header to stack buffer, not just basic one netfilter: nf_conntrack_sip: fix the ct_sip_parse_numerical_param() return value. ipvlan: Fix return value of ipvlan_queue_xmit() netlink: Add __sock_i_ino() for __netlink_diag_dump(). drm/amd/display: Add logging for display MALL refresh setting radeon: avoid double free in ci_dpm_init() drm/amd/display: Explicitly specify update type per plane info change Input: drv260x - sleep between polling GO bit drm/bridge: tc358768: always enable HS video mode drm/bridge: tc358768: fix PLL parameters computation drm/bridge: tc358768: fix PLL target frequency drm/bridge: tc358768: fix TCLK_ZEROCNT computation drm/bridge: tc358768: Add atomic_get_input_bus_fmts() implementation drm/bridge: tc358768: fix TCLK_TRAILCNT computation drm/bridge: tc358768: fix THS_ZEROCNT computation drm/bridge: tc358768: fix TXTAGOCNT computation drm/bridge: tc358768: fix THS_TRAILCNT computation drm/vram-helper: fix function names in vram helper doc ARM: dts: BCM5301X: Drop "clock-names" from the SPI node ARM: dts: meson8b: correct uart_B and uart_C clock references Input: adxl34x - do not hardcode interrupt trigger type drm: sun4i_tcon: use devm_clk_get_enabled in `sun4i_tcon_init_clocks` drm/panel: sharp-ls043t1le01: adjust mode settings ARM: dts: stm32: Move ethernet MAC EEPROM from SoM to carrier boards bus: ti-sysc: Fix dispc quirk masking bool variables arm64: dts: microchip: sparx5: do not use PSCI on reference boards clk: imx: scu: use _safe list iterator to avoid a use after free RDMA/bnxt_re: Disable/kill tasklet only if it is enabled RDMA/bnxt_re: Fix to remove unnecessary return labels RDMA/bnxt_re: Use unique names while registering interrupts RDMA/bnxt_re: Remove a redundant check inside bnxt_re_update_gid RDMA/bnxt_re: Fix to remove an unnecessary log drm/msm/dsi: don't allow enabling 14nm VCO with unprogrammed rate drm/msm/disp/dpu: get timing engine status from intf status register drm/msm/dpu: Set DPU_DATA_HCTL_EN for in INTF_SC7180_MASK ARM: dts: gta04: Move model property out of pinctrl node arm64: dts: qcom: msm8916: correct camss unit address arm64: dts: qcom: msm8994: correct SPMI unit address arm64: dts: qcom: msm8996: correct camss unit address arm64: dts: qcom: sdm630: correct camss unit address arm64: dts: qcom: sdm845: correct camss unit address arm64: dts: qcom: db820c: Move blsp1_uart2 pin states to msm8996.dtsi arm64: dts: qcom: apq8016-sbc: Update modem and WiFi firmware path arm64: dts: qcom: apq8016-sbc: Clarify firmware-names arm64: dts: qcom: apq8016-sbc: fix mpps state names arm64: dts: qcom: Drop unneeded extra device-specific includes arm64: dts: qcom: apq8016-sbc: Fix regulator constraints arm64: dts: qcom: apq8016-sbc: Fix 1.8V power rail on LS expansion drm/panel: simple: fix active size for Ampire AM-480272H3TMQW-T01H ARM: ep93xx: fix missing-prototype warnings ARM: omap2: fix missing tick_broadcast() prototype arm64: dts: qcom: apq8096: fix fixed regulator name property arm64: dts: mediatek: mt8183: Add mediatek,broken-save-restore-fw to kukui ARM: dts: stm32: Shorten the AV96 HDMI sound card name memory: brcmstb_dpfe: fix testing array offset after use ASoC: es8316: Increment max value for ALC Capture Target Volume control ASoC: es8316: Do not set rate constraints for unsupported MCLKs ARM: dts: meson8: correct uart_B and uart_C clock references soc/fsl/qe: fix usb.c build errors RDMA/irdma: avoid fortify-string warning in irdma_clr_wqes IB/hfi1: Use bitmap_zalloc() when applicable IB/hfi1: Fix wrong mmu_node used for user SDMA packet after invalidate RDMA/hns: Fix hns_roce_table_get return value ARM: dts: iwg20d-q7-common: Fix backlight pwm specifier arm64: dts: renesas: ulcb-kf: Remove flow control for SCIF1 fbdev: omapfb: lcd_mipid: Fix an error handling path in mipid_spi_probe() arm64: dts: ti: k3-j7200: Fix physical address of pin ARM: dts: stm32: Fix audio routing on STM32MP15xx DHCOM PDK2 ARM: dts: stm32: fix i2s endpoint format property for stm32mp15xx-dkx hwmon: (gsc-hwmon) fix fan pwm temperature scaling hwmon: (adm1275) Allow setting sample averaging hwmon: (pmbus/adm1275) Fix problems with temperature monitoring on ADM1272 ARM: dts: BCM5301X: fix duplex-full => full-duplex drm/amdkfd: Fix potential deallocation of previously deallocated memory. drm/amd/display: Fix artifacting on eDP panels when engaging freesync video mode drm/radeon: fix possible division-by-zero errors amdgpu: validate offset_in_bo of drm_amdgpu_gem_va drm/msm/a5xx: really check for A510 in a5xx_gpu_init RDMA/bnxt_re: wraparound mbox producer index RDMA/bnxt_re: Avoid calling wake_up threads from spin_lock context clk: imx: clk-imx8mn: fix memory leak in imx8mn_clocks_probe clk: imx: clk-imx8mp: improve error handling in imx8mp_clocks_probe() arm64: dts: qcom: sm8250-edo: Panel framebuffer is 2.5k instead of 4k clk: clocking-wizard: Fix Oops in clk_wzrd_register_divider() clk: tegra: tegra124-emc: Fix potential memory leak ALSA: ac97: Fix possible NULL dereference in snd_ac97_mixer drm/msm/dpu: do not enable color-management if DSPPs are not available drm/msm/dp: Free resources after unregistering them arm64: dts: mediatek: Add cpufreq nodes for MT8192 arm64: dts: mediatek: mt8192: Fix CPUs capacity-dmips-mhz drm/msm/dpu: correct MERGE_3D length clk: vc5: check memory returned by kasprintf() clk: cdce925: check return value of kasprintf() clk: si5341: return error if one synth clock registration fails clk: si5341: check return value of {devm_}kasprintf() clk: si5341: free unused memory on probe failure clk: keystone: sci-clk: check return value of kasprintf() clk: ti: clkctrl: check return value of kasprintf() drivers: meson: secure-pwrc: always enable DMA domain ovl: update of dentry revalidate flags after copy up ASoC: imx-audmix: check return value of devm_kasprintf() clk: Fix memory leak in devm_clk_notifier_register() PCI: cadence: Fix Gen2 Link Retraining process PCI: vmd: Reset VMD config register between soft reboots scsi: qedf: Fix NULL dereference in error handling pinctrl: bcm2835: Handle gpiochip_add_pin_range() errors PCI/ASPM: Disable ASPM on MFD function removal to avoid use-after-free scsi: 3w-xxxx: Add error handling for initialization failure in tw_probe() PCI: pciehp: Cancel bringup sequence if card is not present PCI: ftpci100: Release the clock resources PCI: Add pci_clear_master() stub for non-CONFIG_PCI perf bench: Use unbuffered output when pipe/tee'ing to a file perf bench: Add missing setlocale() call to allow usage of %'d style formatting pinctrl: cherryview: Return correct value if pin in push-pull mode kcsan: Don't expect 64 bits atomic builtins from 32 bits architectures powerpc/interrupt: Don't read MSR from interrupt_exit_kernel_prepare() powerpc/signal32: Force inlining of __unsafe_save_user_regs() and save_tm_user_regs_unsafe() perf script: Fix allocation of evsel->priv related to per-event dump files perf dwarf-aux: Fix off-by-one in die_get_varname() powerpc/64s: Fix VAS mm use after free pinctrl: microchip-sgpio: check return value of devm_kasprintf() pinctrl: at91-pio4: check return value of devm_kasprintf() powerpc/powernv/sriov: perform null check on iov before dereferencing iov powerpc: simplify ppc_save_regs powerpc: update ppc_save_regs to save current r1 in pt_regs riscv: uprobes: Restore thread.bad_cause powerpc/book3s64/mm: Fix DirectMap stats in /proc/meminfo powerpc/mm/dax: Fix the condition when checking if altmap vmemap can cross-boundary hwrng: virtio - add an internal buffer hwrng: virtio - don't wait on cleanup hwrng: virtio - don't waste entropy hwrng: virtio - always add a pending request hwrng: virtio - Fix race on data_avail and actual data modpost: remove broken calculation of exception_table_entry size crypto: nx - fix build warnings when DEBUG_FS is not enabled modpost: fix section mismatch message for R_ARM_ABS32 modpost: fix section mismatch message for R_ARM_{PC24,CALL,JUMP24} crypto: marvell/cesa - Fix type mismatch warning modpost: fix off by one in is_executable_section() ARC: define ASM_NL and __ALIGN(_STR) outside #ifdef __ASSEMBLY__ guard crypto: qat - honor CRYPTO_TFM_REQ_MAY_SLEEP flag crypto: qat - replace get_current_node() with numa_node_id() crypto: qat - use reference to structure in dma_map_single() crypto: kpp - Add helper to set reqsize crypto: qat - Use helper to set reqsize crypto: qat - unmap buffer before free for DH crypto: qat - unmap buffers before free for RSA NFSv4.1: freeze the session table upon receiving NFS4ERR_BADSESSION SMB3: Do not send lease break acknowledgment if all file handles have been closed dax: Fix dax_mapping_release() use after free dax: Introduce alloc_dev_dax_id() dax/kmem: Pass valid argument to memory_group_register_static hwrng: st - keep clock enabled while hwrng is registered kbuild: Disable GCOV for *.mod.o efi/libstub: Disable PCI DMA before grabbing the EFI memory map ksmbd: avoid field overflow warning ACPI: utils: Fix acpi_evaluate_dsm_typed() redefinition error bootmem: remove the vmemmap pages from kmemleak in free_bootmem_page io_uring: ensure IOPOLL locks around deferred work USB: serial: option: add LARA-R6 01B PIDs usb: dwc3: gadget: Propagate core init errors to UDC during pullup phy: tegra: xusb: Clear the driver reference in usb-phy dev iio: adc: ad7192: Fix null ad7192_state pointer access iio: adc: ad7192: Fix internal/external clock selection iio: accel: fxls8962af: errata bug only applicable for FXLS8962AF iio: accel: fxls8962af: fixup buffer scan element type ALSA: hda/realtek: Add quirk for Clevo NPx0SNx ALSA: jack: Fix mutex call in snd_jack_report() block: fix signed int overflow in Amiga partition support block: add overflow checks for Amiga partition support block: change all __u32 annotations to __be32 in affs_hardblocks.h block: increment diskseq on all media change events SUNRPC: Fix UAF in svc_tcp_listen_data_ready() w1: w1_therm: fix locking behavior in convert_t w1: fix loop in w1_fini() sh: j2: Use ioremap() to translate device tree address into kernel memory usb: dwc2: platform: Improve error reporting for problems during .remove() usb: dwc2: Fix some error handling paths serial: 8250: omap: Fix freeing of resources on failed register clk: qcom: camcc-sc7180: Add parent dependency to all camera GDSCs clk: qcom: gcc-ipq6018: Use floor ops for sdcc clocks media: usb: Check az6007_read() return value media: videodev2.h: Fix struct v4l2_input tuner index comment media: usb: siano: Fix warning due to null work_func_t function pointer media: i2c: Correct format propagation for st-mipid02 clk: qcom: reset: Allow specifying custom reset delay clk: qcom: reset: support resetting multiple bits clk: qcom: ipq6018: fix networking resets usb: dwc3: qcom: Fix potential memory leak usb: gadget: u_serial: Add null pointer check in gserial_suspend extcon: Fix kernel doc of property fields to avoid warnings extcon: Fix kernel doc of property capability fields to avoid warnings usb: phy: phy-tahvo: fix memory leak in tahvo_usb_probe() usb: hide unused usbfs_notify_suspend/resume functions serial: 8250: lock port for stop_rx() in omap8250_irq() serial: 8250: lock port for UART_IER access in omap8250_irq() kernfs: fix missing kernfs_idr_lock to remove an ID from the IDR coresight: Fix loss of connection info when a module is unloaded mfd: rt5033: Drop rt5033-battery sub-device media: venus: helpers: Fix ALIGN() of non power of two media: atomisp: gmin_platform: fix out_len in gmin_get_config_dsm_var() KVM: s390: fix KVM_S390_GET_CMMA_BITS for GFNs in memslot holes usb: dwc3: qcom: Release the correct resources in dwc3_qcom_remove() usb: dwc3: qcom: Fix an error handling path in dwc3_qcom_probe() usb: common: usb-conn-gpio: Set last role to unknown before initial detection usb: dwc3-meson-g12a: Fix an error handling path in dwc3_meson_g12a_probe() mfd: intel-lpss: Add missing check for platform_get_resource Revert "usb: common: usb-conn-gpio: Set last role to unknown before initial detection" serial: 8250_omap: Use force_suspend and resume for system suspend test_firmware: return ENOMEM instead of ENOSPC on failed memory allocation nvmem: rmem: Use NVMEM_DEVID_AUTO mfd: stmfx: Fix error path in stmfx_chip_init mfd: stmfx: Nullify stmfx->vdd in case of error KVM: s390: vsie: fix the length of APCB bitmap KVM: s390/diag: fix racy access of physical cpu number in diag 9c handler mfd: stmpe: Only disable the regulators if they are enabled phy: tegra: xusb: check return value of devm_kzalloc() pwm: imx-tpm: force 'real_period' to be zero in suspend pwm: sysfs: Do not apply state to already disabled PWMs pwm: ab8500: Fix error code in probe() pwm: mtk_disp: Fix the disable flow of disp_pwm md/raid10: fix the condition to call bio_end_io_acct() rtc: st-lpc: Release some resources in st_rtc_probe() in case of error drm/i915/psr: Use hw.adjusted mode when calculating io/fast wake times media: cec: i2c: ch7322: also select REGMAP sctp: fix potential deadlock on &net->sctp.addr_wq_lock net/sched: act_ipt: add sanity checks on table name and hook locations Add MODULE_FIRMWARE() for FIRMWARE_TG357766. ibmvnic: Do not reset dql stats on NON_FATAL err net: dsa: vsc73xx: fix MTU configuration spi: bcm-qspi: return error if neither hif_mspi nor mspi is available mailbox: ti-msgmgr: Fill non-message tx data fields with 0x0 f2fs: fix error path handling in truncate_dnode() octeontx2-af: Fix mapping for NIX block from CGX connection octeontx2-af: Add validation before accessing cgx and lmac ntfs: Fix panic about slab-out-of-bounds caused by ntfs_listxattr() powerpc: allow PPC_EARLY_DEBUG_CPM only when SERIAL_CPM=y net: bridge: keep ports without IFF_UNICAST_FLT in BR_PROMISC mode tcp: annotate data races in __tcp_oow_rate_limited() xsk: Honor SO_BINDTODEVICE on bind net/sched: act_pedit: Add size check for TCA_PEDIT_PARMS_EX riscv: move memblock_allow_resize() after linear mapping is ready pptp: Fix fib lookup calls. net: dsa: tag_sja1105: fix MAC DA patching from meta frames octeontx-af: fix hardware timestamp configuration s390/qeth: Fix vipa deletion sh: dma: Fix DMA channel offset calculation apparmor: fix missing error check for rhashtable_insert_fast i2c: xiic: Defer xiic_wakeup() and __xiic_start_xfer() in xiic_process() i2c: xiic: Don't try to handle more interrupt events after error extcon: usbc-tusb320: Convert to i2c's .probe_new() btrfs: do not BUG_ON() on tree mod log failure at balance_level() i2c: qup: Add missing unwind goto in qup_i2c_probe() NFSD: add encoding of op_recall flag for write delegation io_uring: wait interruptibly for request completions on exit mmc: core: disable TRIM on Kingston EMMC04G-M627 mmc: core: disable TRIM on Micron MTFC4GACAJCN-1M mmc: mmci: Set PROBE_PREFER_ASYNCHRONOUS mmc: sdhci: fix DMA configure compatibility issue when 64bit DMA mode is used. bcache: fixup btree_cache_wait list damage bcache: Remove unnecessary NULL point check in node allocations bcache: Fix __bch_btree_node_alloc to make the failure behavior consistent um: Use HOST_DIR for mrproper integrity: Fix possible multiple allocation in integrity_inode_get() autofs: use flexible array in ioctl structure shmem: use ramfs_kill_sb() for kill_sb method of ramfs-based tmpfs ext4: Remove ext4 locking of moved directory Revert "f2fs: fix potential corruption when moving a directory" fs: Establish locking order for unrelated directories fs: Lock moved directories ipvs: increase ip_vs_conn_tab_bits range for 64BIT jffs2: reduce stack usage in jffs2_build_xattr_subsystem() fs: avoid empty option when generating legacy mount string btrfs: add handling for RAID1C23/DUP to btrfs_reduce_alloc_profile btrfs: delete unused BGs while reclaiming BGs btrfs: bail out reclaim process if filesystem is read-only btrfs: reinsert BGs failed to reclaim btrfs: fix race when deleting quota root from the dirty cow roots list btrfs: fix extent buffer leak after tree mod log failure at split_node() btrfs: do not BUG_ON() on tree mod log failure at __btrfs_cow_block() ASoC: mediatek: mt8173: Fix irq error path ASoC: mediatek: mt8173: Fix snd_soc_component_initialize error path ARM: dts: qcom: ipq4019: fix broken NAND controller properties override ARM: orion5x: fix d2net gpio initialization leds: trigger: netdev: Recheck NETDEV_LED_MODE_LINKUP on dev rename fs: no need to check source ovl: fix null pointer dereference in ovl_get_acl_rcu() fanotify: disallow mount/sb marks on kernel internal pseudo fs netfilter: nf_tables: unbind non-anonymous set if rule construction fails netfilter: conntrack: Avoid nf_ct_helper_hash uses after free netfilter: nf_tables: do not ignore genmask when looking up chain by id netfilter: nf_tables: prevent OOB access in nft_byteorder_eval wireguard: queueing: use saner cpu selection wrapping wireguard: netlink: send staged packets when setting initial private key tty: serial: fsl_lpuart: add earlycon for imx8ulp platform block/partition: fix signedness issue for Amiga partitions io_uring: Use io_schedule* in cqring wait io_uring: add reschedule point to handle_tw_list() net: lan743x: Don't sleep in atomic context workqueue: clean up WORK_* constant types, clarify masking ksmbd: use ksmbd_req_buf_next() in ksmbd_smb2_check_message() ksmbd: validate command payload size ksmbd: fix out-of-bound read in smb2_write ksmbd: validate session id and tree id in the compound request drm/panel: simple: Add connector_type for innolux_at043tn24 drm/bridge: ti-sn65dsi86: Fix auxiliary bus lifetime drm/panel: simple: Add Powertip PH800480T013 drm_display_mode flags igc: Remove delay during TX ring configuration net/mlx5e: fix double free in mlx5e_destroy_flow_table net/mlx5e: fix memory leak in mlx5e_ptp_open net/mlx5e: Check for NOT_READY flag state after locking igc: set TP bit in 'supported' and 'advertising' fields of ethtool_link_ksettings igc: Handle PPS start time programming for past time values scsi: qla2xxx: Fix error code in qla2x00_start_sp() bpf: Fix max stack depth check for async callbacks net: mvneta: fix txq_map in case of txq_number==1 net/sched: cls_fw: Fix improper refcount update leads to use-after-free gve: Set default duplex configuration to full ionic: remove WARN_ON to prevent panic_on_warn net: bgmac: postpone turning IRQs off to avoid SoC hangs net: prevent skb corruption on frag list segmentation icmp6: Fix null-ptr-deref of ip6_null_entry->rt6i_idev in icmp6_dev(). udp6: fix udp6_ehashfn() typo ntb: idt: Fix error handling in idt_pci_driver_init() NTB: amd: Fix error handling in amd_ntb_pci_driver_init() ntb: intel: Fix error handling in intel_ntb_pci_driver_init() NTB: ntb_transport: fix possible memory leak while device_register() fails NTB: ntb_tool: Add check for devm_kcalloc ipv6/addrconf: fix a potential refcount underflow for idev platform/x86: wmi: remove unnecessary argument platform/x86: wmi: use guid_t and guid_equal() platform/x86: wmi: move variables platform/x86: wmi: Break possible infinite loop when parsing GUID kernel/trace: Fix cleanup logic of enable_trace_eprobe igc: Fix launchtime before start of cycle igc: Fix inserting of empty frame for launchtime bpf, riscv: Support riscv jit to provide bpf_line_info riscv, bpf: Fix inconsistent JIT image generation drm/i915: Fix one wrong caching mode enum usage octeontx2-pf: Add additional check for MCAM rules erofs: avoid infinite loop in z_erofs_do_read_page() when reading beyond EOF erofs: decouple basic mount options from fs_context erofs: fix fsdax unavailability for chunk-based regular files wifi: airo: avoid uninitialized warning in airo_get_rate() bpf: cpumap: Fix memory leak in cpu_map_update_elem net/sched: flower: Ensure both minimum and maximum ports are specified riscv: mm: fix truncation warning on RV32 netdevsim: fix uninitialized data in nsim_dev_trap_fa_cookie_write() net/sched: make psched_mtu() RTNL-less safe net/sched: sch_qfq: refactor parsing of netlink parameters net/sched: sch_qfq: account for stab overhead in qfq_enqueue nvme-pci: remove nvme_queue from nvme_iod nvme-pci: fix DMA direction of unmapping integrity data fs/ntfs3: Check fields while reading f2fs: fix to avoid NULL pointer dereference f2fs_write_end_io() pinctrl: amd: Fix mistake in handling clearing pins at startup pinctrl: amd: Detect internal GPIO0 debounce handling pinctrl: amd: Detect and mask spurious interrupts pinctrl: amd: Only use special debounce behavior for GPIO 0 tpm: tpm_vtpm_proxy: fix a race condition in /dev/vtpmx creation mtd: rawnand: meson: fix unaligned DMA buffers handling net: bcmgenet: Ensure MDIO unregistration has clocks enabled mm/damon/ops-common: atomically test and clear young on ptes and pmds powerpc: Fail build if using recordmcount with binutils v2.37 misc: fastrpc: Create fastrpc scalar with correct buffer count powerpc/security: Fix Speculation_Store_Bypass reporting on Power10 arm64: errata: Add detection for TRBE overwrite in FILL mode erofs: fix compact 4B support for 16k block size MIPS: Loongson: Fix cpu_probe_loongson() again MIPS: KVM: Fix NULL pointer dereference ext4: Fix reusing stale buffer heads from last failed mounting ext4: fix wrong unit use in ext4_mb_clear_bb ext4: get block from bh in ext4_free_blocks for fast commit replay ext4: fix wrong unit use in ext4_mb_new_blocks ext4: fix to check return value of freeze_bdev() in ext4_shutdown() ext4: turn quotas off if mount failed after enabling quotas ext4: only update i_reserved_data_blocks on successful block allocation jfs: jfs_dmap: Validate db_l2nbperpage while mounting hwrng: imx-rngc - fix the timeout for init and self check dm integrity: reduce vmalloc space footprint on 32-bit architectures PCI/PM: Avoid putting EloPOS E2/S2/H2 PCIe Ports in D3cold PCI: Add function 1 DMA alias quirk for Marvell 88SE9235 PCI: qcom: Disable write access to read only registers for IP v2.3.3 PCI: rockchip: Assert PCI Configuration Enable bit after probe PCI: rockchip: Write PCI Device ID to correct register PCI: rockchip: Add poll and timeout to wait for PHY PLLs to be locked PCI: rockchip: Fix legacy IRQ generation for RK3399 PCIe endpoint core PCI: rockchip: Use u32 variable to access 32-bit registers PCI: rockchip: Set address alignment for endpoint mode misc: pci_endpoint_test: Free IRQs before removing the device misc: pci_endpoint_test: Re-init completion for every test mfd: pm8008: Fix module autoloading md/raid0: add discard support for the 'original' layout dm init: add dm-mod.waitfor to wait for asynchronously probed block devices fs: dlm: return positive pid value for F_GETLK drm/atomic: Allow vblank-enabled + self-refresh "disable" drm/rockchip: vop: Leave vblank enabled in self-refresh drm/amdgpu: fix clearing mappings for BOs that are always valid in VM drm/amd/display: Correct `DMUB_FW_VERSION` macro drm/amdgpu: avoid restore process run into dead loop. drm/ttm: Don't leak a resource on swapout move error serial: atmel: don't enable IRQs prematurely tty: serial: samsung_tty: Fix a memory leak in s3c24xx_serial_getclk() in case of error tty: serial: samsung_tty: Fix a memory leak in s3c24xx_serial_getclk() when iterating clk tty: serial: imx: fix rs485 rx after tx firmware: stratix10-svc: Fix a potential resource leak in svc_create_memory_pool() libceph: harden msgr2.1 frame segment length checks ceph: don't let check_caps skip sending responses for revoke msgs xhci: Fix resume issue of some ZHAOXIN hosts xhci: Fix TRB prefetch issue of ZHAOXIN hosts xhci: Show ZHAOXIN xHCI root hub speed correctly meson saradc: fix clock divider mask length opp: Fix use-after-free in lazy_opp_tables after probe deferral soundwire: qcom: fix storing port config out-of-bounds Revert "8250: add support for ASIX devices with a FIFO bug" bus: ixp4xx: fix IXP4XX_EXP_T1_MASK s390/decompressor: fix misaligned symbol build error tracing/histograms: Add histograms to hist_vars if they have referenced variables tracing: Fix memory leak of iter->temp when reading trace_pipe samples: ftrace: Save required argument registers in sample trampolines net: ena: fix shift-out-of-bounds in exponential backoff ring-buffer: Fix deadloop issue on reading trace_pipe ftrace: Fix possible warning on checking all pages used in ftrace_process_locs() xtensa: ISS: fix call to split_if_spec tracing: Fix null pointer dereference in tracing_err_log_open() selftests: mptcp: sockopt: return error if wrong mark selftests: mptcp: depend on SYN_COOKIES tracing/probes: Fix not to count error code to total length tracing/probes: Fix to update dynamic data counter if fetcharg uses it scsi: qla2xxx: Wait for io return on terminate rport scsi: qla2xxx: Array index may go out of bound scsi: qla2xxx: Avoid fcport pointer dereference scsi: qla2xxx: Fix buffer overrun scsi: qla2xxx: Fix potential NULL pointer dereference scsi: qla2xxx: Check valid rport returned by fc_bsg_to_rport() scsi: qla2xxx: Correct the index of array scsi: qla2xxx: Pointer may be dereferenced scsi: qla2xxx: Remove unused nvme_ls_waitq wait queue MIPS: kvm: Fix build error with KVM_MIPS_DEBUG_COP0_COUNTERS enabled net/sched: sch_qfq: reintroduce lmax bound check for MTU drm/atomic: Fix potential use-after-free in nonblocking commits Linux 5.15.121 Note, this merges away commit e4e7f67cc1 ("arm64: errata: Add detection for TRBE overwrite in FILL mode") as it causes ABI issues. If that is to be needed for this branch, it can come back later in an ABI-safe way. It also merges away commit 7eeed3ed1a ("mm/damon/ops-common: atomically test and clear young on ptes and pmds") as it had too many merge conflicts. If that is needed in a future release it needs to be added as a proper BACKPORT. Change-Id: Ie91971a85cbb2672e9d2ef1d90814817697ca7b3 Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
2026-03-25 20:10:23 +09:00 · 2023-08-03 18:15:58 +00:00
parent ab76251526 cdd3cdb682
commit 9f5bde3ccf
441 changed files with 5730 additions and 3989 deletions
--- a/Documentation/admin-guide/device-mapper/dm-init.rst
+++ b/Documentation/admin-guide/device-mapper/dm-init.rst
@@ -123,3 +123,11 @@ Other examples (per target):
    0 1638400 verity 1 8:1 8:2 4096 4096 204800 1 sha256
    fb1a5a0f00deb908d8b53cb270858975e76cf64105d412ce764225d53b8f3cfd
    51934789604d1b92399c52e7cb149d1b3a1b74bbbcb103b2a0aaacbed5c08584
+
+For setups using device-mapper on top of asynchronously probed block
+devices (MMC, USB, ..), it may be necessary to tell dm-init to
+explicitly wait for them to become available before setting up the
+device-mapper tables. This can be done with the "dm-mod.waitfor="
+module parameter, which takes a list of devices to wait for::
+
+  dm-mod.waitfor=<device1>[,..,<deviceN>]
--- a/Documentation/filesystems/autofs-mount-control.rst
+++ b/Documentation/filesystems/autofs-mount-control.rst
@@ -196,7 +196,7 @@ information and return operation results::
 		    struct args_ismountpoint	ismountpoint;
 	    };

-	    char path[0];
+	    char path[];
    };

 The ioctlfd field is a mount point file descriptor of an autofs mount
--- a/Documentation/filesystems/autofs.rst
+++ b/Documentation/filesystems/autofs.rst
@@ -467,7 +467,7 @@ Each ioctl is passed a pointer to an `autofs_dev_ioctl` structure::
 			struct args_ismountpoint	ismountpoint;
 		};

-                char path[0];
+                char path[];
        };

 For the **OPEN_MOUNT** and **IS_MOUNTPOINT** commands, the target
--- a/Documentation/filesystems/directory-locking.rst
+++ b/Documentation/filesystems/directory-locking.rst
@@ -22,12 +22,11 @@ exclusive.
 3) object removal.  Locking rules: caller locks parent, finds victim,
 locks victim and calls the method.  Locks are exclusive.

-4) rename() that is _not_ cross-directory.  Locking rules: caller locks
-the parent and finds source and target.  In case of exchange (with
-RENAME_EXCHANGE in flags argument) lock both.  In any case,
-if the target already exists, lock it.  If the source is a non-directory,
-lock it.  If we need to lock both, lock them in inode pointer order.
-Then call the method.  All locks are exclusive.
+4) rename() that is _not_ cross-directory.  Locking rules: caller locks the
+parent and finds source and target.  We lock both (provided they exist).  If we
+need to lock two inodes of different type (dir vs non-dir), we lock directory
+first.  If we need to lock two inodes of the same type, lock them in inode
+pointer order.  Then call the method.  All locks are exclusive.
 NB: we might get away with locking the source (and target in exchange
 case) shared.

@@ -44,15 +43,17 @@ All locks are exclusive.
 rules:

 	* lock the filesystem
-	* lock parents in "ancestors first" order.
+	* lock parents in "ancestors first" order. If one is not ancestor of
+	  the other, lock them in inode pointer order.
 	* find source and target.
 	* if old parent is equal to or is a descendent of target
 	  fail with -ENOTEMPTY
 	* if new parent is equal to or is a descendent of source
 	  fail with -ELOOP
-	* If it's an exchange, lock both the source and the target.
-	* If the target exists, lock it.  If the source is a non-directory,
-	  lock it.  If we need to lock both, do so in inode pointer order.
+	* Lock both the source and the target provided they exist. If we
+	  need to lock two inodes of different type (dir vs non-dir), we lock
+	  the directory first. If we need to lock two inodes of the same type,
+	  lock them in inode pointer order.
 	* call the method.

 All ->i_rwsem are taken exclusive.  Again, we might get away with locking
@@ -66,8 +67,9 @@ If no directory is its own ancestor, the scheme above is deadlock-free.

 Proof:

-	First of all, at any moment we have a partial ordering of the
-	objects - A < B iff A is an ancestor of B.
+	First of all, at any moment we have a linear ordering of the
+	objects - A < B iff (A is an ancestor of B) or (B is not an ancestor
+        of A and ptr(A) < ptr(B)).

 	That ordering can change.  However, the following is true:

--- a/Documentation/networking/af_xdp.rst
+++ b/Documentation/networking/af_xdp.rst
@@ -433,6 +433,15 @@ start N bytes into the buffer leaving the first N bytes for the
 application to use. The final option is the flags field, but it will
 be dealt with in separate sections for each UMEM flag.

+SO_BINDTODEVICE setsockopt
+--------------------------
+
+This is a generic SOL_SOCKET option that can be used to tie AF_XDP
+socket to a particular network interface.  It is useful when a socket
+is created by a privileged process and passed to a non-privileged one.
+Once the option is set, kernel will refuse attempts to bind that socket
+to a different interface.  Updating the value requires CAP_NET_RAW.
+
 XDP_STATISTICS getsockopt
 -------------------------

--- a/2
+++ b/2
@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 VERSION = 5
 PATCHLEVEL = 15
-SUBLEVEL = 120
+SUBLEVEL = 121
 EXTRAVERSION =
 NAME = Trick or Treat

--- a/arch/arc/include/asm/linkage.h
+++ b/arch/arc/include/asm/linkage.h
@@ -8,6 +8,10 @@

 #include <asm/dwarf.h>

+#define ASM_NL		 `	/* use '`' to mark new line in macro */
+#define __ALIGN		.align 4
+#define __ALIGN_STR	__stringify(__ALIGN)
+
 #ifdef __ASSEMBLY__

 .macro ST2 e, o, off
@@ -28,10 +32,6 @@
 #endif
 .endm

-#define ASM_NL		 `	/* use '`' to mark new line in macro */
-#define __ALIGN		.align 4
-#define __ALIGN_STR	__stringify(__ALIGN)
-
 /* annotation for data we want in DCCM - if enabled in .config */
 .macro ARCFP_DATA nm
 #ifdef CONFIG_ARC_HAS_DCCM
--- a/arch/arm/boot/dts/bcm53015-meraki-mr26.dts
+++ b/arch/arm/boot/dts/bcm53015-meraki-mr26.dts
@@ -128,7 +128,7 @@

 			fixed-link {
 				speed = <1000>;
-				duplex-full;
+				full-duplex;
 			};
 		};
 	};
--- a/arch/arm/boot/dts/bcm53016-meraki-mr32.dts
+++ b/arch/arm/boot/dts/bcm53016-meraki-mr32.dts
@@ -212,7 +212,7 @@

 			fixed-link {
 				speed = <1000>;
-				duplex-full;
+				full-duplex;
 			};
 		};
 	};
--- a/arch/arm/boot/dts/bcm5301x.dtsi
+++ b/arch/arm/boot/dts/bcm5301x.dtsi
@@ -542,7 +542,6 @@
 				  "spi_lr_session_done",
 				  "spi_lr_overread";
 		clocks = <&iprocmed>;
-		clock-names = "iprocmed";
 		num-cs = <2>;
 		#address-cells = <1>;
 		#size-cells = <0>;
--- a/arch/arm/boot/dts/iwg20d-q7-common.dtsi
+++ b/arch/arm/boot/dts/iwg20d-q7-common.dtsi
@@ -49,7 +49,7 @@
 	lcd_backlight: backlight {
 		compatible = "pwm-backlight";

-		pwms = <&pwm3 0 5000000 0>;
+		pwms = <&pwm3 0 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		enable-gpios = <&gpio5 14 GPIO_ACTIVE_HIGH>;
--- a/arch/arm/boot/dts/meson8.dtsi
+++ b/arch/arm/boot/dts/meson8.dtsi
@@ -749,13 +749,13 @@

 &uart_B {
 	compatible = "amlogic,meson8-uart";
-	clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>;
+	clocks = <&xtal>, <&clkc CLKID_UART1>, <&clkc CLKID_CLK81>;
 	clock-names = "xtal", "pclk", "baud";
 };

 &uart_C {
 	compatible = "amlogic,meson8-uart";
-	clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>;
+	clocks = <&xtal>, <&clkc CLKID_UART2>, <&clkc CLKID_CLK81>;
 	clock-names = "xtal", "pclk", "baud";
 };

--- a/arch/arm/boot/dts/meson8b.dtsi
+++ b/arch/arm/boot/dts/meson8b.dtsi
@@ -737,13 +737,13 @@

 &uart_B {
 	compatible = "amlogic,meson8b-uart";
-	clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>;
+	clocks = <&xtal>, <&clkc CLKID_UART1>, <&clkc CLKID_CLK81>;
 	clock-names = "xtal", "pclk", "baud";
 };

 &uart_C {
 	compatible = "amlogic,meson8b-uart";
-	clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>;
+	clocks = <&xtal>, <&clkc CLKID_UART2>, <&clkc CLKID_CLK81>;
 	clock-names = "xtal", "pclk", "baud";
 };

--- a/arch/arm/boot/dts/omap3-gta04a5one.dts
+++ b/arch/arm/boot/dts/omap3-gta04a5one.dts
@@ -5,9 +5,11 @@

 #include "omap3-gta04a5.dts"

-&omap3_pmx_core {
+/ {
 	model = "Goldelico GTA04A5/Letux 2804 with OneNAND";
+};

+&omap3_pmx_core {
 	gpmc_pins: pinmux_gpmc_pins {
 		pinctrl-single,pins = <

--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts
+++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts
@@ -11,9 +11,9 @@
 		dma@7984000 {
 			status = "okay";
 		};
-
-		qpic-nand@79b0000 {
-			status = "okay";
-		};
 	};
 };
+
+&nand {
+	status = "okay";
+};
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi
@@ -102,10 +102,10 @@
 			status = "okay";
 			perst-gpio = <&tlmm 38 0x1>;
 		};
-
-		qpic-nand@79b0000 {
-			pinctrl-0 = <&nand_pins>;
-			pinctrl-names = "default";
-		};
 	};
 };
+
+&nand {
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+};
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi
@@ -65,11 +65,11 @@
 		dma@7984000 {
 			status = "okay";
 		};
-
-		qpic-nand@79b0000 {
-			pinctrl-0 = <&nand_pins>;
-			pinctrl-names = "default";
-			status = "okay";
-		};
 	};
 };
+
+&nand {
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
@@ -137,10 +137,13 @@

 	sound {
 		compatible = "audio-graph-card";
-		routing =
-			"MIC_IN", "Capture",
-			"Capture", "Mic Bias",
-			"Playback", "HP_OUT";
+		widgets = "Headphone", "Headphone Jack",
+			  "Line", "Line In Jack",
+			  "Microphone", "Microphone Jack";
+		routing = "Headphone Jack", "HP_OUT",
+			  "LINE_IN", "Line In Jack",
+			  "MIC_IN", "Microphone Jack",
+			  "Microphone Jack", "Mic Bias";
 		dais = <&sai2a_port &sai2b_port>;
 		status = "okay";
 	};
--- a/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
@@ -88,7 +88,7 @@

 	sound {
 		compatible = "audio-graph-card";
-		label = "STM32MP1-AV96-HDMI";
+		label = "STM32-AV96-HDMI";
 		dais = <&sai2a_port>;
 		status = "okay";
 	};
@@ -267,6 +267,12 @@
 			};
 		};
 	};
+
+	dh_mac_eeprom: eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
 };

 &ltdc {
--- a/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
@@ -171,12 +171,6 @@
 			status = "disabled";
 		};
 	};
-
-	eeprom@53 {
-		compatible = "atmel,24c02";
-		reg = <0x53>;
-		pagesize = <16>;
-	};
 };

 &iwdg2 {
--- a/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi
@@ -438,7 +438,7 @@
 	i2s2_port: port {
 		i2s2_endpoint: endpoint {
 			remote-endpoint = <&sii9022_tx_endpoint>;
-			format = "i2s";
+			dai-format = "i2s";
 			mclk-fs = <256>;
 		};
 	};
--- a/arch/arm/mach-ep93xx/timer-ep93xx.c
+++ b/arch/arm/mach-ep93xx/timer-ep93xx.c
@@ -9,6 +9,7 @@
 #include <linux/io.h>
 #include <asm/mach/time.h>
 #include "soc.h"
+#include "platform.h"

 /*************************************************************************
 * Timer handling for EP93xx
@@ -60,7 +61,7 @@ static u64 notrace ep93xx_read_sched_clock(void)
 	return ret;
 }

-u64 ep93xx_clocksource_read(struct clocksource *c)
+static u64 ep93xx_clocksource_read(struct clocksource *c)
 {
 	u64 ret;

--- a/arch/arm/mach-omap2/board-generic.c
+++ b/arch/arm/mach-omap2/board-generic.c
@@ -13,6 +13,7 @@
 #include <linux/of_platform.h>
 #include <linux/irqdomain.h>
 #include <linux/clocksource.h>
+#include <linux/clockchips.h>

 #include <asm/setup.h>
 #include <asm/mach/arch.h>
--- a/arch/arm/mach-orion5x/board-dt.c
+++ b/arch/arm/mach-orion5x/board-dt.c
@@ -63,6 +63,9 @@ static void __init orion5x_dt_init(void)
 	if (of_machine_is_compatible("maxtor,shared-storage-2"))
 		mss2_init();

+	if (of_machine_is_compatible("lacie,d2-network"))
+		d2net_init();
+
 	of_platform_default_populate(NULL, orion5x_auxdata_lookup, NULL);
 }

--- a/arch/arm/mach-orion5x/common.h
+++ b/arch/arm/mach-orion5x/common.h
@@ -75,6 +75,12 @@ extern void mss2_init(void);
 static inline void mss2_init(void) {}
 #endif

+#ifdef CONFIG_MACH_D2NET_DT
+void d2net_init(void);
+#else
+static inline void d2net_init(void) {}
+#endif
+
 /*****************************************************************************
 * Helpers to access Orion registers
 ****************************************************************************/
--- a/arch/arm64/Kconfig
+++ b/arch/arm64/Kconfig
@@ -871,6 +871,47 @@ config ARM64_ERRATUM_2457168

 	  If unsure, say Y.

+config ARM64_WORKAROUND_TRBE_OVERWRITE_FILL_MODE
+	bool
+
+config ARM64_ERRATUM_2119858
+	bool "Cortex-A710: 2119858: workaround TRBE overwriting trace data in FILL mode"
+	default y
+	depends on COMPILE_TEST # Until the CoreSight TRBE driver changes are in
+	depends on CORESIGHT_TRBE
+	select ARM64_WORKAROUND_TRBE_OVERWRITE_FILL_MODE
+	help
+	  This option adds the workaround for ARM Cortex-A710 erratum 2119858.
+
+	  Affected Cortex-A710 cores could overwrite up to 3 cache lines of trace
+	  data at the base of the buffer (pointed to by TRBASER_EL1) in FILL mode in
+	  the event of a WRAP event.
+
+	  Work around the issue by always making sure we move the TRBPTR_EL1 by
+	  256 bytes before enabling the buffer and filling the first 256 bytes of
+	  the buffer with ETM ignore packets upon disabling.
+
+	  If unsure, say Y.
+
+config ARM64_ERRATUM_2139208
+	bool "Neoverse-N2: 2139208: workaround TRBE overwriting trace data in FILL mode"
+	default y
+	depends on COMPILE_TEST # Until the CoreSight TRBE driver changes are in
+	depends on CORESIGHT_TRBE
+	select ARM64_WORKAROUND_TRBE_OVERWRITE_FILL_MODE
+	help
+	  This option adds the workaround for ARM Neoverse-N2 erratum 2139208.
+
+	  Affected Neoverse-N2 cores could overwrite up to 3 cache lines of trace
+	  data at the base of the buffer (pointed to by TRBASER_EL1) in FILL mode in
+	  the event of a WRAP event.
+
+	  Work around the issue by always making sure we move the TRBPTR_EL1 by
+	  256 bytes before enabling the buffer and filling the first 256 bytes of
+	  the buffer with ETM ignore packets upon disabling.
+
+	  If unsure, say Y.
+
 config CAVIUM_ERRATUM_22375
 	bool "Cavium erratum 22375, 24313"
 	default y
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
@@ -281,6 +281,10 @@
 	};
 };

+&gic {
+	mediatek,broken-save-restore-fw;
+};
+
 &gpu {
 	mali-supply = <&mt6358_vgpu_reg>;
 	sram-supply = <&mt6358_vsram_gpu_reg>;
--- a/arch/arm64/boot/dts/mediatek/mt8192.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8192.dtsi
@@ -41,7 +41,8 @@
 			clock-frequency = <1701000000>;
 			cpu-idle-states = <&cpu_sleep_l &cluster_sleep_l>;
 			next-level-cache = <&l2_0>;
-			capacity-dmips-mhz = <530>;
+			performance-domains = <&performance 0>;
+			capacity-dmips-mhz = <427>;
 		};

 		cpu1: cpu@100 {
@@ -52,7 +53,8 @@
 			clock-frequency = <1701000000>;
 			cpu-idle-states = <&cpu_sleep_l &cluster_sleep_l>;
 			next-level-cache = <&l2_0>;
-			capacity-dmips-mhz = <530>;
+			performance-domains = <&performance 0>;
+			capacity-dmips-mhz = <427>;
 		};

 		cpu2: cpu@200 {
@@ -63,7 +65,8 @@
 			clock-frequency = <1701000000>;
 			cpu-idle-states = <&cpu_sleep_l &cluster_sleep_l>;
 			next-level-cache = <&l2_0>;
-			capacity-dmips-mhz = <530>;
+			performance-domains = <&performance 0>;
+			capacity-dmips-mhz = <427>;
 		};

 		cpu3: cpu@300 {
@@ -74,7 +77,8 @@
 			clock-frequency = <1701000000>;
 			cpu-idle-states = <&cpu_sleep_l &cluster_sleep_l>;
 			next-level-cache = <&l2_0>;
-			capacity-dmips-mhz = <530>;
+			performance-domains = <&performance 0>;
+			capacity-dmips-mhz = <427>;
 		};

 		cpu4: cpu@400 {
@@ -85,6 +89,7 @@
 			clock-frequency = <2171000000>;
 			cpu-idle-states = <&cpu_sleep_b &cluster_sleep_b>;
 			next-level-cache = <&l2_1>;
+			performance-domains = <&performance 1>;
 			capacity-dmips-mhz = <1024>;
 		};

@@ -96,6 +101,7 @@
 			clock-frequency = <2171000000>;
 			cpu-idle-states = <&cpu_sleep_b &cluster_sleep_b>;
 			next-level-cache = <&l2_1>;
+			performance-domains = <&performance 1>;
 			capacity-dmips-mhz = <1024>;
 		};

@@ -107,6 +113,7 @@
 			clock-frequency = <2171000000>;
 			cpu-idle-states = <&cpu_sleep_b &cluster_sleep_b>;
 			next-level-cache = <&l2_1>;
+			performance-domains = <&performance 1>;
 			capacity-dmips-mhz = <1024>;
 		};

@@ -118,6 +125,7 @@
 			clock-frequency = <2171000000>;
 			cpu-idle-states = <&cpu_sleep_b &cluster_sleep_b>;
 			next-level-cache = <&l2_1>;
+			performance-domains = <&performance 1>;
 			capacity-dmips-mhz = <1024>;
 		};

@@ -234,6 +242,12 @@
 		compatible = "simple-bus";
 		ranges;

+		performance: performance-controller@11bc10 {
+			compatible = "mediatek,cpufreq-hw";
+			reg = <0 0x0011bc10 0 0x120>, <0 0x0011bd30 0 0x120>;
+			#performance-domain-cells = <1>;
+		};
+
 		gic: interrupt-controller@c000000 {
 			compatible = "arm,gic-v3";
 			#interrupt-cells = <4>;
--- a/arch/arm64/boot/dts/microchip/sparx5.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5.dtsi
@@ -61,7 +61,7 @@
 		interrupt-affinity = <&cpu0>, <&cpu1>;
 	};

-	psci {
+	psci: psci {
 		compatible = "arm,psci-0.2";
 		method = "smc";
 	};
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb_common.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb_common.dtsi
@@ -6,6 +6,18 @@
 /dts-v1/;
 #include "sparx5.dtsi"

+&psci {
+	status = "disabled";
+};
+
+&cpu0 {
+	enable-method = "spin-table";
+};
+
+&cpu1 {
+	enable-method = "spin-table";
+};
+
 &uart0 {
 	status = "okay";
 };
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dts
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dts
@@ -5,9 +5,847 @@

 /dts-v1/;

-#include "apq8016-sbc.dtsi"
+#include "msm8916-pm8916.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+#include <dt-bindings/sound/apq8016-lpass.h>

 / {
 	model = "Qualcomm Technologies, Inc. APQ 8016 SBC";
 	compatible = "qcom,apq8016-sbc", "qcom,apq8016";
+
+	aliases {
+		serial0 = &blsp1_uart2;
+		serial1 = &blsp1_uart1;
+		usid0 = &pm8916_0;
+		i2c0	= &blsp_i2c2;
+		i2c1	= &blsp_i2c6;
+		i2c3	= &blsp_i2c4;
+		spi0	= &blsp_spi5;
+		spi1	= &blsp_spi3;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	camera_vdddo_1v8: camera-vdddo-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "camera_vdddo";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	camera_vdda_2v8: camera-vdda-2v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "camera_vdda";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		regulator-always-on;
+	};
+
+	camera_vddd_1v5: camera-vddd-1v5 {
+		compatible = "regulator-fixed";
+		regulator-name = "camera_vddd";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+	};
+
+	reserved-memory {
+		ramoops@bff00000 {
+			compatible = "ramoops";
+			reg = <0x0 0xbff00000 0x0 0x100000>;
+
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			ftrace-size = <0x20000>;
+		};
+	};
+
+	usb2513 {
+		compatible = "smsc,usb3503";
+		reset-gpios = <&pm8916_gpios 3 GPIO_ACTIVE_LOW>;
+		initial-mode = <1>;
+	};
+
+	usb_id: usb-id {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&msmgpio 121 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_id_default>;
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&adv7533_out>;
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&msm_key_volp_n_default>;
+
+		button@0 {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&msmgpio_leds>,
+			    <&pm8916_gpios_leds>,
+			    <&pm8916_mpps_leds>;
+
+		compatible = "gpio-leds";
+
+		led@1 {
+			label = "apq8016-sbc:green:user1";
+			gpios = <&msmgpio 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led@2 {
+			label = "apq8016-sbc:green:user2";
+			gpios = <&msmgpio 120 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		led@3 {
+			label = "apq8016-sbc:green:user3";
+			gpios = <&pm8916_gpios 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc1";
+			default-state = "off";
+		};
+
+		led@4 {
+			label = "apq8016-sbc:green:user4";
+			gpios = <&pm8916_gpios 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "none";
+			panic-indicator;
+			default-state = "off";
+		};
+
+		led@5 {
+			label = "apq8016-sbc:yellow:wlan";
+			gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy0tx";
+			default-state = "off";
+		};
+
+		led@6 {
+			label = "apq8016-sbc:blue:bt";
+			gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "bluetooth-power";
+			default-state = "off";
+		};
+	};
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp_i2c2 {
+	/* On Low speed expansion */
+	status = "okay";
+	label = "LS-I2C0";
+};
+
+&blsp_i2c4 {
+	/* On High speed expansion */
+	status = "okay";
+	label = "HS-I2C2";
+
+	adv_bridge: bridge@39 {
+		status = "okay";
+
+		compatible = "adi,adv7533";
+		reg = <0x39>;
+
+		interrupt-parent = <&msmgpio>;
+		interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+
+		adi,dsi-lanes = <4>;
+		clocks = <&rpmcc RPM_SMD_BB_CLK2>;
+		clock-names = "cec";
+
+		pd-gpios = <&msmgpio 32 GPIO_ACTIVE_HIGH>;
+
+		avdd-supply = <&pm8916_l6>;
+		v1p2-supply = <&pm8916_l6>;
+		v3p3-supply = <&pm8916_l17>;
+
+		pinctrl-names = "default","sleep";
+		pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
+		pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
+		#sound-dai-cells = <1>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7533_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				adv7533_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+		};
+	};
+};
+
+&blsp_i2c6 {
+	/* On Low speed expansion */
+	status = "okay";
+	label = "LS-I2C1";
+};
+
+&blsp_spi3 {
+	/* On High speed expansion */
+	status = "okay";
+	label = "HS-SPI1";
+};
+
+&blsp_spi5 {
+	/* On Low speed expansion */
+	status = "okay";
+	label = "LS-SPI0";
+};
+
+&blsp1_uart1 {
+	status = "okay";
+	label = "LS-UART0";
+};
+
+&blsp1_uart2 {
+	status = "okay";
+	label = "LS-UART1";
+};
+
+&camss {
+	status = "okay";
+	ports {
+		port@0 {
+			reg = <0>;
+			csiphy0_ep: endpoint {
+				clock-lanes = <1>;
+				data-lanes = <0 2>;
+				remote-endpoint = <&ov5640_ep>;
+				status = "okay";
+			};
+		};
+	};
+};
+
+&cci {
+	status = "okay";
+};
+
+&cci_i2c0 {
+	camera_rear@3b {
+		compatible = "ovti,ov5640";
+		reg = <0x3b>;
+
+		enable-gpios = <&msmgpio 34 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&camera_rear_default>;
+
+		clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+		clock-names = "xclk";
+		clock-frequency = <23880000>;
+
+		vdddo-supply = <&camera_vdddo_1v8>;
+		vdda-supply = <&camera_vdda_2v8>;
+		vddd-supply = <&camera_vddd_1v5>;
+
+		/* No camera mezzanine by default */
+		status = "disabled";
+
+		port {
+			ov5640_ep: endpoint {
+				clock-lanes = <1>;
+				data-lanes = <0 2>;
+				remote-endpoint = <&csiphy0_ep>;
+			};
+		};
+	};
+};
+
+&dsi0_out {
+	data-lanes = <0 1 2 3>;
+	remote-endpoint = <&adv7533_in>;
+};
+
+&lpass {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mpss {
+	status = "okay";
+
+	firmware-name = "qcom/apq8016/mba.mbn", "qcom/apq8016/modem.mbn";
+};
+
+&pm8916_resin {
+	status = "okay";
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&pronto {
+	status = "okay";
+
+	firmware-name = "qcom/apq8016/wcnss.mbn";
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
+	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
+	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+
+	cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>;
+};
+
+&sound {
+	status = "okay";
+
+	pinctrl-0 = <&cdc_pdm_lines_act &ext_sec_tlmm_lines_act &ext_mclk_tlmm_lines_act>;
+	pinctrl-1 = <&cdc_pdm_lines_sus &ext_sec_tlmm_lines_sus &ext_mclk_tlmm_lines_sus>;
+	pinctrl-names = "default", "sleep";
+	qcom,model = "DB410c";
+	qcom,audio-routing =
+		"AMIC2", "MIC BIAS Internal2",
+		"AMIC3", "MIC BIAS External1";
+
+	external-dai-link@0 {
+		link-name = "ADV7533";
+		cpu {
+			sound-dai = <&lpass MI2S_QUATERNARY>;
+		};
+		codec {
+			sound-dai = <&adv_bridge 0>;
+		};
+	};
+
+	internal-codec-playback-dai-link@0 {
+		link-name = "WCD";
+		cpu {
+			sound-dai = <&lpass MI2S_PRIMARY>;
+		};
+		codec {
+			sound-dai = <&lpass_codec 0>, <&wcd_codec 0>;
+		};
+	};
+
+	internal-codec-capture-dai-link@0 {
+		link-name = "WCD-Capture";
+		cpu {
+			sound-dai = <&lpass MI2S_TERTIARY>;
+		};
+		codec {
+			sound-dai = <&lpass_codec 1>, <&wcd_codec 1>;
+		};
+	};
+};
+
+&usb {
+	status = "okay";
+	extcon = <&usb_id>, <&usb_id>;
+
+	pinctrl-names = "default", "device";
+	pinctrl-0 = <&usb_sw_sel_pm &usb_hub_reset_pm>;
+	pinctrl-1 = <&usb_sw_sel_pm_device &usb_hub_reset_pm_device>;
+};
+
+&usb_hs_phy {
+	extcon = <&usb_id>;
+};
+
+&wcd_codec {
+	clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>;
+	clock-names = "mclk";
+	qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
+	qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
+};
+
+&wcnss_ctrl {
+	firmware-name = "qcom/apq8016/WCNSS_qcom_wlan_nv_sbc.bin";
+};
+
+/* Enable CoreSight */
+&cti0 { status = "okay"; };
+&cti1 { status = "okay"; };
+&cti12 { status = "okay"; };
+&cti13 { status = "okay"; };
+&cti14 { status = "okay"; };
+&cti15 { status = "okay"; };
+&debug0 { status = "okay"; };
+&debug1 { status = "okay"; };
+&debug2 { status = "okay"; };
+&debug3 { status = "okay"; };
+&etf { status = "okay"; };
+&etm0 { status = "okay"; };
+&etm1 { status = "okay"; };
+&etm2 { status = "okay"; };
+&etm3 { status = "okay"; };
+&etr { status = "okay"; };
+&funnel0 { status = "okay"; };
+&funnel1 { status = "okay"; };
+&replicator { status = "okay"; };
+&stm { status = "okay"; };
+&tpiu { status = "okay"; };
+
+&smd_rpm_regulators {
+	vdd_l1_l2_l3-supply = <&pm8916_s3>;
+	vdd_l4_l5_l6-supply = <&pm8916_s4>;
+	vdd_l7-supply = <&pm8916_s4>;
+
+	s3 {
+		regulator-min-microvolt = <1250000>;
+		regulator-max-microvolt = <1350000>;
+	};
+
+	s4 {
+		regulator-min-microvolt = <1850000>;
+		regulator-max-microvolt = <2150000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	l1 {
+		regulator-min-microvolt = <1225000>;
+		regulator-max-microvolt = <1225000>;
+	};
+
+	l2 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+	};
+
+	l4 {
+		regulator-min-microvolt = <2050000>;
+		regulator-max-microvolt = <2050000>;
+	};
+
+	l5 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l6 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l7 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l8 {
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+	};
+
+	l9 {
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l10 {
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+	};
+
+	l11 {
+		regulator-min-microvolt = <2950000>;
+		regulator-max-microvolt = <2950000>;
+		regulator-allow-set-load;
+		regulator-system-load = <200000>;
+	};
+
+	l12 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2950000>;
+	};
+
+	l13 {
+		regulator-min-microvolt = <3075000>;
+		regulator-max-microvolt = <3075000>;
+	};
+
+	l14 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	/*
+	 * The 96Boards specification expects a 1.8V power rail on the low-speed
+	 * expansion connector that is able to provide at least 0.18W / 100 mA.
+	 * L15/L16 are connected in parallel to provide 55 mA each. A minimum load
+	 * must be specified to ensure the regulators are not put in LPM where they
+	 * would only provide 5 mA.
+	 */
+	l15 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-system-load = <50000>;
+		regulator-allow-set-load;
+		regulator-always-on;
+	};
+
+	l16 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-system-load = <50000>;
+		regulator-allow-set-load;
+		regulator-always-on;
+	};
+
+	l17 {
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l18 {
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2700000>;
+	};
+};
+
+/*
+ * 2mA drive strength is not enough when connecting multiple
+ * I2C devices with different pull up resistors.
+ */
+&i2c2_default {
+	drive-strength = <16>;
+};
+
+&i2c4_default {
+	drive-strength = <16>;
+};
+
+&i2c6_default {
+	drive-strength = <16>;
+};
+
+/*
+ * GPIO name legend: proper name = the GPIO line is used as GPIO
+ *         NC = not connected (pin out but not routed from the chip to
+ *              anything the board)
+ *         "[PER]" = pin is muxed for [peripheral] (not GPIO)
+ *         LSEC = Low Speed External Connector
+ *         HSEC = High Speed External Connector
+ *
+ * Line names are taken from the schematic "DragonBoard410c"
+ * dated monday, august 31, 2015. Page 5 in particular.
+ *
+ * For the lines routed to the external connectors the
+ * lines are named after the 96Boards CE Specification 1.0,
+ * Appendix "Expansion Connector Signal Description".
+ *
+ * When the 96Board naming of a line and the schematic name of
+ * the same line are in conflict, the 96Board specification
+ * takes precedence, which means that the external UART on the
+ * LSEC is named UART0 while the schematic and SoC names this
+ * UART3. This is only for the informational lines i.e. "[FOO]",
+ * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
+ * ones actually used for GPIO.
+ */
+
+&msmgpio {
+	gpio-line-names =
+		"[UART0_TX]", /* GPIO_0, LSEC pin 5 */
+		"[UART0_RX]", /* GPIO_1, LSEC pin 7 */
+		"[UART0_CTS_N]", /* GPIO_2, LSEC pin 3 */
+		"[UART0_RTS_N]", /* GPIO_3, LSEC pin 9 */
+		"[UART1_TX]", /* GPIO_4, LSEC pin 11 */
+		"[UART1_RX]", /* GPIO_5, LSEC pin 13 */
+		"[I2C0_SDA]", /* GPIO_8, LSEC pin 17 */
+		"[I2C0_SCL]", /* GPIO_7, LSEC pin 15 */
+		"[SPI1_DOUT]", /* SPI1_MOSI, HSEC pin 1 */
+		"[SPI1_DIN]", /* SPI1_MISO, HSEC pin 11 */
+		"[SPI1_CS]", /* SPI1_CS_N, HSEC pin 7 */
+		"[SPI1_SCLK]", /* SPI1_CLK, HSEC pin 9 */
+		"GPIO-B", /* LS_EXP_GPIO_B, LSEC pin 24 */
+		"GPIO-C", /* LS_EXP_GPIO_C, LSEC pin 25 */
+		"[I2C3_SDA]", /* HSEC pin 38 */
+		"[I2C3_SCL]", /* HSEC pin 36 */
+		"[SPI0_MOSI]", /* LSEC pin 14 */
+		"[SPI0_MISO]", /* LSEC pin 10 */
+		"[SPI0_CS_N]", /* LSEC pin 12 */
+		"[SPI0_CLK]", /* LSEC pin 8 */
+		"HDMI_HPD_N", /* GPIO 20 */
+		"USR_LED_1_CTRL",
+		"[I2C1_SDA]", /* GPIO_22, LSEC pin 21 */
+		"[I2C1_SCL]", /* GPIO_23, LSEC pin 19 */
+		"GPIO-G", /* LS_EXP_GPIO_G, LSEC pin 29 */
+		"GPIO-H", /* LS_EXP_GPIO_H, LSEC pin 30 */
+		"[CSI0_MCLK]", /* HSEC pin 15 */
+		"[CSI1_MCLK]", /* HSEC pin 17 */
+		"GPIO-K", /* LS_EXP_GPIO_K, LSEC pin 33 */
+		"[I2C2_SDA]", /* HSEC pin 34 */
+		"[I2C2_SCL]", /* HSEC pin 32 */
+		"DSI2HDMI_INT_N",
+		"DSI_SW_SEL_APQ",
+		"GPIO-L", /* LS_EXP_GPIO_L, LSEC pin 34 */
+		"GPIO-J", /* LS_EXP_GPIO_J, LSEC pin 32 */
+		"GPIO-I", /* LS_EXP_GPIO_I, LSEC pin 31 */
+		"GPIO-A", /* LS_EXP_GPIO_A, LSEC pin 23 */
+		"FORCED_USB_BOOT",
+		"SD_CARD_DET_N",
+		"[WCSS_BT_SSBI]",
+		"[WCSS_WLAN_DATA_2]", /* GPIO 40 */
+		"[WCSS_WLAN_DATA_1]",
+		"[WCSS_WLAN_DATA_0]",
+		"[WCSS_WLAN_SET]",
+		"[WCSS_WLAN_CLK]",
+		"[WCSS_FM_SSBI]",
+		"[WCSS_FM_SDI]",
+		"[WCSS_BT_DAT_CTL]",
+		"[WCSS_BT_DAT_STB]",
+		"NC",
+		"NC", /* GPIO 50 */
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC", /* GPIO 60 */
+		"NC",
+		"NC",
+		"[CDC_PDM0_CLK]",
+		"[CDC_PDM0_SYNC]",
+		"[CDC_PDM0_TX0]",
+		"[CDC_PDM0_RX0]",
+		"[CDC_PDM0_RX1]",
+		"[CDC_PDM0_RX2]",
+		"GPIO-D", /* LS_EXP_GPIO_D, LSEC pin 26 */
+		"NC", /* GPIO 70 */
+		"NC",
+		"NC",
+		"NC",
+		"NC", /* GPIO 74 */
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"BOOT_CONFIG_0", /* GPIO 80 */
+		"BOOT_CONFIG_1",
+		"BOOT_CONFIG_2",
+		"BOOT_CONFIG_3",
+		"NC",
+		"NC",
+		"BOOT_CONFIG_5",
+		"NC",
+		"NC",
+		"NC",
+		"NC", /* GPIO 90 */
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC", /* GPIO 100 */
+		"NC",
+		"NC",
+		"NC",
+		"SSBI_GPS",
+		"NC",
+		"NC",
+		"KEY_VOLP_N",
+		"NC",
+		"NC",
+		"[LS_EXP_MI2S_WS]", /* GPIO 110 */
+		"NC",
+		"NC",
+		"[LS_EXP_MI2S_SCK]",
+		"[LS_EXP_MI2S_DATA0]",
+		"GPIO-E", /* LS_EXP_GPIO_E, LSEC pin 27 */
+		"NC",
+		"[DSI2HDMI_MI2S_WS]",
+		"[DSI2HDMI_MI2S_SCK]",
+		"[DSI2HDMI_MI2S_DATA0]",
+		"USR_LED_2_CTRL", /* GPIO 120 */
+		"SB_HS_ID";
+
+	msmgpio_leds: msmgpio-leds {
+		pins = "gpio21", "gpio120";
+		function = "gpio";
+
+		output-low;
+	};
+
+	usb_id_default: usb-id-default {
+		pins = "gpio121";
+		function = "gpio";
+
+		drive-strength = <8>;
+		input-enable;
+		bias-pull-up;
+	};
+
+	adv7533_int_active: adv533-int-active {
+		pins = "gpio31";
+		function = "gpio";
+
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	adv7533_int_suspend: adv7533-int-suspend {
+		pins = "gpio31";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	adv7533_switch_active: adv7533-switch-active {
+		pins = "gpio32";
+		function = "gpio";
+
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	adv7533_switch_suspend: adv7533-switch-suspend {
+		pins = "gpio32";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	msm_key_volp_n_default: msm-key-volp-n-default {
+		pins = "gpio107";
+		function = "gpio";
+
+		drive-strength = <8>;
+		input-enable;
+		bias-pull-up;
+	};
+};
+
+&pm8916_gpios {
+	gpio-line-names =
+		"USR_LED_3_CTRL",
+		"USR_LED_4_CTRL",
+		"USB_HUB_RESET_N_PM",
+		"USB_SW_SEL_PM";
+
+	usb_hub_reset_pm: usb-hub-reset-pm {
+		pins = "gpio3";
+		function = PMIC_GPIO_FUNC_NORMAL;
+
+		input-disable;
+		output-high;
+	};
+
+	usb_hub_reset_pm_device: usb-hub-reset-pm-device {
+		pins = "gpio3";
+		function = PMIC_GPIO_FUNC_NORMAL;
+
+		output-low;
+	};
+
+	usb_sw_sel_pm: usb-sw-sel-pm {
+		pins = "gpio4";
+		function = PMIC_GPIO_FUNC_NORMAL;
+
+		power-source = <PM8916_GPIO_VPH>;
+		input-disable;
+		output-high;
+	};
+
+	usb_sw_sel_pm_device: usb-sw-sel-pm-device {
+		pins = "gpio4";
+		function = PMIC_GPIO_FUNC_NORMAL;
+
+		power-source = <PM8916_GPIO_VPH>;
+		input-disable;
+		output-low;
+	};
+
+	pm8916_gpios_leds: pm8916-gpios-leds {
+		pins = "gpio1", "gpio2";
+		function = PMIC_GPIO_FUNC_NORMAL;
+
+		output-low;
+	};
+};
+
+&pm8916_mpps {
+	gpio-line-names =
+		"VDD_PX_BIAS",
+		"WLAN_LED_CTRL",
+		"BT_LED_CTRL",
+		"GPIO-F"; /* LS_EXP_GPIO_F, LSEC pin 28 */
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&ls_exp_gpio_f>;
+
+	ls_exp_gpio_f: pm8916-mpp4-state {
+		pins = "mpp4";
+		function = "digital";
+
+		output-low;
+		power-source = <PM8916_MPP_L5>;	// 1.8V
+	};
+
+	pm8916_mpps_leds: pm8916-mpps-state {
+		pins = "mpp2", "mpp3";
+		function = "digital";
+
+		output-low;
+	};
 };
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
@@ -1,826 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (c) 2015, The Linux Foundation. All rights reserved.
- */
-
-#include "msm8916-pm8916.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
-#include <dt-bindings/sound/apq8016-lpass.h>
-
-/ {
-	aliases {
-		serial0 = &blsp1_uart2;
-		serial1 = &blsp1_uart1;
-		usid0 = &pm8916_0;
-		i2c0	= &blsp_i2c2;
-		i2c1	= &blsp_i2c6;
-		i2c3	= &blsp_i2c4;
-		spi0	= &blsp_spi5;
-		spi1	= &blsp_spi3;
-	};
-
-	chosen {
-		stdout-path = "serial0";
-	};
-
-	camera_vdddo_1v8: camera-vdddo-1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "camera_vdddo";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-always-on;
-	};
-
-	camera_vdda_2v8: camera-vdda-2v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "camera_vdda";
-		regulator-min-microvolt = <2800000>;
-		regulator-max-microvolt = <2800000>;
-		regulator-always-on;
-	};
-
-	camera_vddd_1v5: camera-vddd-1v5 {
-		compatible = "regulator-fixed";
-		regulator-name = "camera_vddd";
-		regulator-min-microvolt = <1500000>;
-		regulator-max-microvolt = <1500000>;
-		regulator-always-on;
-	};
-
-	reserved-memory {
-		ramoops@bff00000 {
-			compatible = "ramoops";
-			reg = <0x0 0xbff00000 0x0 0x100000>;
-
-			record-size = <0x20000>;
-			console-size = <0x20000>;
-			ftrace-size = <0x20000>;
-		};
-	};
-
-	usb2513 {
-		compatible = "smsc,usb3503";
-		reset-gpios = <&pm8916_gpios 3 GPIO_ACTIVE_LOW>;
-		initial-mode = <1>;
-	};
-
-	usb_id: usb-id {
-		compatible = "linux,extcon-usb-gpio";
-		id-gpio = <&msmgpio 121 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&usb_id_default>;
-	};
-
-	hdmi-out {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_con: endpoint {
-				remote-endpoint = <&adv7533_out>;
-			};
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		autorepeat;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&msm_key_volp_n_default>;
-
-		button@0 {
-			label = "Volume Up";
-			linux,code = <KEY_VOLUMEUP>;
-			gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	leds {
-		pinctrl-names = "default";
-		pinctrl-0 = <&msmgpio_leds>,
-			    <&pm8916_gpios_leds>,
-			    <&pm8916_mpps_leds>;
-
-		compatible = "gpio-leds";
-
-		led@1 {
-			label = "apq8016-sbc:green:user1";
-			gpios = <&msmgpio 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-			default-state = "off";
-		};
-
-		led@2 {
-			label = "apq8016-sbc:green:user2";
-			gpios = <&msmgpio 120 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc0";
-			default-state = "off";
-		};
-
-		led@3 {
-			label = "apq8016-sbc:green:user3";
-			gpios = <&pm8916_gpios 1 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc1";
-			default-state = "off";
-		};
-
-		led@4 {
-			label = "apq8016-sbc:green:user4";
-			gpios = <&pm8916_gpios 2 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "none";
-			panic-indicator;
-			default-state = "off";
-		};
-
-		led@5 {
-			label = "apq8016-sbc:yellow:wlan";
-			gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "phy0tx";
-			default-state = "off";
-		};
-
-		led@6 {
-			label = "apq8016-sbc:blue:bt";
-			gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "bluetooth-power";
-			default-state = "off";
-		};
-	};
-};
-
-&blsp_dma {
-	status = "okay";
-};
-
-&blsp_i2c2 {
-	/* On Low speed expansion */
-	status = "okay";
-	label = "LS-I2C0";
-};
-
-&blsp_i2c4 {
-	/* On High speed expansion */
-	status = "okay";
-	label = "HS-I2C2";
-
-	adv_bridge: bridge@39 {
-		status = "okay";
-
-		compatible = "adi,adv7533";
-		reg = <0x39>;
-
-		interrupt-parent = <&msmgpio>;
-		interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
-
-		adi,dsi-lanes = <4>;
-		clocks = <&rpmcc RPM_SMD_BB_CLK2>;
-		clock-names = "cec";
-
-		pd-gpios = <&msmgpio 32 GPIO_ACTIVE_HIGH>;
-
-		avdd-supply = <&pm8916_l6>;
-		v1p2-supply = <&pm8916_l6>;
-		v3p3-supply = <&pm8916_l17>;
-
-		pinctrl-names = "default","sleep";
-		pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
-		pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
-		#sound-dai-cells = <1>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				adv7533_in: endpoint {
-					remote-endpoint = <&dsi0_out>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-				adv7533_out: endpoint {
-					remote-endpoint = <&hdmi_con>;
-				};
-			};
-		};
-	};
-};
-
-&blsp_i2c6 {
-	/* On Low speed expansion */
-	status = "okay";
-	label = "LS-I2C1";
-};
-
-&blsp_spi3 {
-	/* On High speed expansion */
-	status = "okay";
-	label = "HS-SPI1";
-};
-
-&blsp_spi5 {
-	/* On Low speed expansion */
-	status = "okay";
-	label = "LS-SPI0";
-};
-
-&blsp1_uart1 {
-	status = "okay";
-	label = "LS-UART0";
-};
-
-&blsp1_uart2 {
-	status = "okay";
-	label = "LS-UART1";
-};
-
-&camss {
-	status = "okay";
-	ports {
-		port@0 {
-			reg = <0>;
-			csiphy0_ep: endpoint {
-				clock-lanes = <1>;
-				data-lanes = <0 2>;
-				remote-endpoint = <&ov5640_ep>;
-				status = "okay";
-			};
-		};
-	};
-};
-
-&cci {
-	status = "okay";
-};
-
-&cci_i2c0 {
-	camera_rear@3b {
-		compatible = "ovti,ov5640";
-		reg = <0x3b>;
-
-		enable-gpios = <&msmgpio 34 GPIO_ACTIVE_HIGH>;
-		reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&camera_rear_default>;
-
-		clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
-		clock-names = "xclk";
-		clock-frequency = <23880000>;
-
-		vdddo-supply = <&camera_vdddo_1v8>;
-		vdda-supply = <&camera_vdda_2v8>;
-		vddd-supply = <&camera_vddd_1v5>;
-
-		/* No camera mezzanine by default */
-		status = "disabled";
-
-		port {
-			ov5640_ep: endpoint {
-				clock-lanes = <1>;
-				data-lanes = <0 2>;
-				remote-endpoint = <&csiphy0_ep>;
-			};
-		};
-	};
-};
-
-&dsi0_out {
-	data-lanes = <0 1 2 3>;
-	remote-endpoint = <&adv7533_in>;
-};
-
-&lpass {
-	status = "okay";
-};
-
-&mdss {
-	status = "okay";
-};
-
-&pm8916_resin {
-	status = "okay";
-	linux,code = <KEY_VOLUMEDOWN>;
-};
-
-&pronto {
-	status = "okay";
-};
-
-&sdhc_1 {
-	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
-	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
-};
-
-&sdhc_2 {
-	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
-	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
-
-	cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>;
-};
-
-&sound {
-	status = "okay";
-
-	pinctrl-0 = <&cdc_pdm_lines_act &ext_sec_tlmm_lines_act &ext_mclk_tlmm_lines_act>;
-	pinctrl-1 = <&cdc_pdm_lines_sus &ext_sec_tlmm_lines_sus &ext_mclk_tlmm_lines_sus>;
-	pinctrl-names = "default", "sleep";
-	qcom,model = "DB410c";
-	qcom,audio-routing =
-		"AMIC2", "MIC BIAS Internal2",
-		"AMIC3", "MIC BIAS External1";
-
-	external-dai-link@0 {
-		link-name = "ADV7533";
-		cpu {
-			sound-dai = <&lpass MI2S_QUATERNARY>;
-		};
-		codec {
-			sound-dai = <&adv_bridge 0>;
-		};
-	};
-
-	internal-codec-playback-dai-link@0 {
-		link-name = "WCD";
-		cpu {
-			sound-dai = <&lpass MI2S_PRIMARY>;
-		};
-		codec {
-			sound-dai = <&lpass_codec 0>, <&wcd_codec 0>;
-		};
-	};
-
-	internal-codec-capture-dai-link@0 {
-		link-name = "WCD-Capture";
-		cpu {
-			sound-dai = <&lpass MI2S_TERTIARY>;
-		};
-		codec {
-			sound-dai = <&lpass_codec 1>, <&wcd_codec 1>;
-		};
-	};
-};
-
-&usb {
-	status = "okay";
-	extcon = <&usb_id>, <&usb_id>;
-
-	pinctrl-names = "default", "device";
-	pinctrl-0 = <&usb_sw_sel_pm &usb_hub_reset_pm>;
-	pinctrl-1 = <&usb_sw_sel_pm_device &usb_hub_reset_pm_device>;
-};
-
-&usb_hs_phy {
-	extcon = <&usb_id>;
-};
-
-&wcd_codec {
-	clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>;
-	clock-names = "mclk";
-	qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
-	qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
-};
-
-/* Enable CoreSight */
-&cti0 { status = "okay"; };
-&cti1 { status = "okay"; };
-&cti12 { status = "okay"; };
-&cti13 { status = "okay"; };
-&cti14 { status = "okay"; };
-&cti15 { status = "okay"; };
-&debug0 { status = "okay"; };
-&debug1 { status = "okay"; };
-&debug2 { status = "okay"; };
-&debug3 { status = "okay"; };
-&etf { status = "okay"; };
-&etm0 { status = "okay"; };
-&etm1 { status = "okay"; };
-&etm2 { status = "okay"; };
-&etm3 { status = "okay"; };
-&etr { status = "okay"; };
-&funnel0 { status = "okay"; };
-&funnel1 { status = "okay"; };
-&replicator { status = "okay"; };
-&stm { status = "okay"; };
-&tpiu { status = "okay"; };
-
-&smd_rpm_regulators {
-	vdd_l1_l2_l3-supply = <&pm8916_s3>;
-	vdd_l4_l5_l6-supply = <&pm8916_s4>;
-	vdd_l7-supply = <&pm8916_s4>;
-
-	s3 {
-		regulator-min-microvolt = <375000>;
-		regulator-max-microvolt = <1562000>;
-	};
-
-	s4 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-
-		regulator-always-on;
-		regulator-boot-on;
-	};
-
-	l1 {
-		regulator-min-microvolt = <375000>;
-		regulator-max-microvolt = <1525000>;
-	};
-
-	l2 {
-		regulator-min-microvolt = <1200000>;
-		regulator-max-microvolt = <1200000>;
-	};
-
-	l4 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	l5 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	l6 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-	};
-
-	l7 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	l8 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	l9 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	l10 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	l11 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-		regulator-allow-set-load;
-		regulator-system-load = <200000>;
-	};
-
-	l12 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	l13 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	l14 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	/**
-	 * 1.8v required on LS expansion
-	 * for mezzanine boards
-	 */
-	l15 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-		regulator-always-on;
-	};
-
-	l16 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	l17 {
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	l18 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-};
-
-/*
- * 2mA drive strength is not enough when connecting multiple
- * I2C devices with different pull up resistors.
- */
-&i2c2_default {
-	drive-strength = <16>;
-};
-
-&i2c4_default {
-	drive-strength = <16>;
-};
-
-&i2c6_default {
-	drive-strength = <16>;
-};
-
-/*
- * GPIO name legend: proper name = the GPIO line is used as GPIO
- *         NC = not connected (pin out but not routed from the chip to
- *              anything the board)
- *         "[PER]" = pin is muxed for [peripheral] (not GPIO)
- *         LSEC = Low Speed External Connector
- *         HSEC = High Speed External Connector
- *
- * Line names are taken from the schematic "DragonBoard410c"
- * dated monday, august 31, 2015. Page 5 in particular.
- *
- * For the lines routed to the external connectors the
- * lines are named after the 96Boards CE Specification 1.0,
- * Appendix "Expansion Connector Signal Description".
- *
- * When the 96Board naming of a line and the schematic name of
- * the same line are in conflict, the 96Board specification
- * takes precedence, which means that the external UART on the
- * LSEC is named UART0 while the schematic and SoC names this
- * UART3. This is only for the informational lines i.e. "[FOO]",
- * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
- * ones actually used for GPIO.
- */
-
-&msmgpio {
-	gpio-line-names =
-		"[UART0_TX]", /* GPIO_0, LSEC pin 5 */
-		"[UART0_RX]", /* GPIO_1, LSEC pin 7 */
-		"[UART0_CTS_N]", /* GPIO_2, LSEC pin 3 */
-		"[UART0_RTS_N]", /* GPIO_3, LSEC pin 9 */
-		"[UART1_TX]", /* GPIO_4, LSEC pin 11 */
-		"[UART1_RX]", /* GPIO_5, LSEC pin 13 */
-		"[I2C0_SDA]", /* GPIO_8, LSEC pin 17 */
-		"[I2C0_SCL]", /* GPIO_7, LSEC pin 15 */
-		"[SPI1_DOUT]", /* SPI1_MOSI, HSEC pin 1 */
-		"[SPI1_DIN]", /* SPI1_MISO, HSEC pin 11 */
-		"[SPI1_CS]", /* SPI1_CS_N, HSEC pin 7 */
-		"[SPI1_SCLK]", /* SPI1_CLK, HSEC pin 9 */
-		"GPIO-B", /* LS_EXP_GPIO_B, LSEC pin 24 */
-		"GPIO-C", /* LS_EXP_GPIO_C, LSEC pin 25 */
-		"[I2C3_SDA]", /* HSEC pin 38 */
-		"[I2C3_SCL]", /* HSEC pin 36 */
-		"[SPI0_MOSI]", /* LSEC pin 14 */
-		"[SPI0_MISO]", /* LSEC pin 10 */
-		"[SPI0_CS_N]", /* LSEC pin 12 */
-		"[SPI0_CLK]", /* LSEC pin 8 */
-		"HDMI_HPD_N", /* GPIO 20 */
-		"USR_LED_1_CTRL",
-		"[I2C1_SDA]", /* GPIO_22, LSEC pin 21 */
-		"[I2C1_SCL]", /* GPIO_23, LSEC pin 19 */
-		"GPIO-G", /* LS_EXP_GPIO_G, LSEC pin 29 */
-		"GPIO-H", /* LS_EXP_GPIO_H, LSEC pin 30 */
-		"[CSI0_MCLK]", /* HSEC pin 15 */
-		"[CSI1_MCLK]", /* HSEC pin 17 */
-		"GPIO-K", /* LS_EXP_GPIO_K, LSEC pin 33 */
-		"[I2C2_SDA]", /* HSEC pin 34 */
-		"[I2C2_SCL]", /* HSEC pin 32 */
-		"DSI2HDMI_INT_N",
-		"DSI_SW_SEL_APQ",
-		"GPIO-L", /* LS_EXP_GPIO_L, LSEC pin 34 */
-		"GPIO-J", /* LS_EXP_GPIO_J, LSEC pin 32 */
-		"GPIO-I", /* LS_EXP_GPIO_I, LSEC pin 31 */
-		"GPIO-A", /* LS_EXP_GPIO_A, LSEC pin 23 */
-		"FORCED_USB_BOOT",
-		"SD_CARD_DET_N",
-		"[WCSS_BT_SSBI]",
-		"[WCSS_WLAN_DATA_2]", /* GPIO 40 */
-		"[WCSS_WLAN_DATA_1]",
-		"[WCSS_WLAN_DATA_0]",
-		"[WCSS_WLAN_SET]",
-		"[WCSS_WLAN_CLK]",
-		"[WCSS_FM_SSBI]",
-		"[WCSS_FM_SDI]",
-		"[WCSS_BT_DAT_CTL]",
-		"[WCSS_BT_DAT_STB]",
-		"NC",
-		"NC", /* GPIO 50 */
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC", /* GPIO 60 */
-		"NC",
-		"NC",
-		"[CDC_PDM0_CLK]",
-		"[CDC_PDM0_SYNC]",
-		"[CDC_PDM0_TX0]",
-		"[CDC_PDM0_RX0]",
-		"[CDC_PDM0_RX1]",
-		"[CDC_PDM0_RX2]",
-		"GPIO-D", /* LS_EXP_GPIO_D, LSEC pin 26 */
-		"NC", /* GPIO 70 */
-		"NC",
-		"NC",
-		"NC",
-		"NC", /* GPIO 74 */
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"BOOT_CONFIG_0", /* GPIO 80 */
-		"BOOT_CONFIG_1",
-		"BOOT_CONFIG_2",
-		"BOOT_CONFIG_3",
-		"NC",
-		"NC",
-		"BOOT_CONFIG_5",
-		"NC",
-		"NC",
-		"NC",
-		"NC", /* GPIO 90 */
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC", /* GPIO 100 */
-		"NC",
-		"NC",
-		"NC",
-		"SSBI_GPS",
-		"NC",
-		"NC",
-		"KEY_VOLP_N",
-		"NC",
-		"NC",
-		"[LS_EXP_MI2S_WS]", /* GPIO 110 */
-		"NC",
-		"NC",
-		"[LS_EXP_MI2S_SCK]",
-		"[LS_EXP_MI2S_DATA0]",
-		"GPIO-E", /* LS_EXP_GPIO_E, LSEC pin 27 */
-		"NC",
-		"[DSI2HDMI_MI2S_WS]",
-		"[DSI2HDMI_MI2S_SCK]",
-		"[DSI2HDMI_MI2S_DATA0]",
-		"USR_LED_2_CTRL", /* GPIO 120 */
-		"SB_HS_ID";
-
-	msmgpio_leds: msmgpio-leds {
-		pins = "gpio21", "gpio120";
-		function = "gpio";
-
-		output-low;
-	};
-
-	usb_id_default: usb-id-default {
-		pins = "gpio121";
-		function = "gpio";
-
-		drive-strength = <8>;
-		input-enable;
-		bias-pull-up;
-	};
-
-	adv7533_int_active: adv533-int-active {
-		pins = "gpio31";
-		function = "gpio";
-
-		drive-strength = <16>;
-		bias-disable;
-	};
-
-	adv7533_int_suspend: adv7533-int-suspend {
-		pins = "gpio31";
-		function = "gpio";
-
-		drive-strength = <2>;
-		bias-disable;
-	};
-
-	adv7533_switch_active: adv7533-switch-active {
-		pins = "gpio32";
-		function = "gpio";
-
-		drive-strength = <16>;
-		bias-disable;
-	};
-
-	adv7533_switch_suspend: adv7533-switch-suspend {
-		pins = "gpio32";
-		function = "gpio";
-
-		drive-strength = <2>;
-		bias-disable;
-	};
-
-	msm_key_volp_n_default: msm-key-volp-n-default {
-		pins = "gpio107";
-		function = "gpio";
-
-		drive-strength = <8>;
-		input-enable;
-		bias-pull-up;
-	};
-};
-
-&pm8916_gpios {
-	gpio-line-names =
-		"USR_LED_3_CTRL",
-		"USR_LED_4_CTRL",
-		"USB_HUB_RESET_N_PM",
-		"USB_SW_SEL_PM";
-
-	usb_hub_reset_pm: usb-hub-reset-pm {
-		pins = "gpio3";
-		function = PMIC_GPIO_FUNC_NORMAL;
-
-		input-disable;
-		output-high;
-	};
-
-	usb_hub_reset_pm_device: usb-hub-reset-pm-device {
-		pins = "gpio3";
-		function = PMIC_GPIO_FUNC_NORMAL;
-
-		output-low;
-	};
-
-	usb_sw_sel_pm: usb-sw-sel-pm {
-		pins = "gpio4";
-		function = PMIC_GPIO_FUNC_NORMAL;
-
-		power-source = <PM8916_GPIO_VPH>;
-		input-disable;
-		output-high;
-	};
-
-	usb_sw_sel_pm_device: usb-sw-sel-pm-device {
-		pins = "gpio4";
-		function = PMIC_GPIO_FUNC_NORMAL;
-
-		power-source = <PM8916_GPIO_VPH>;
-		input-disable;
-		output-low;
-	};
-
-	pm8916_gpios_leds: pm8916-gpios-leds {
-		pins = "gpio1", "gpio2";
-		function = PMIC_GPIO_FUNC_NORMAL;
-
-		output-low;
-	};
-};
-
-&pm8916_mpps {
-	gpio-line-names =
-		"VDD_PX_BIAS",
-		"WLAN_LED_CTRL",
-		"BT_LED_CTRL",
-		"GPIO-F"; /* LS_EXP_GPIO_F, LSEC pin 28 */
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&ls_exp_gpio_f>;
-
-	ls_exp_gpio_f: pm8916-mpp4 {
-		pins = "mpp4";
-		function = "digital";
-
-		output-low;
-		power-source = <PM8916_MPP_L5>;	// 1.8V
-	};
-
-	pm8916_mpps_leds: pm8916-mpps-leds {
-		pins = "mpp2", "mpp3";
-		function = "digital";
-
-		output-low;
-	};
-};
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
--- a/arch/arm64/boot/dts/qcom/apq8096-ifc6640.dts
+++ b/arch/arm64/boot/dts/qcom/apq8096-ifc6640.dts
@@ -26,7 +26,7 @@

 	v1p05: v1p05-regulator {
 		compatible = "regulator-fixed";
-		reglator-name = "v1p05";
+		regulator-name = "v1p05";
 		regulator-always-on;
 		regulator-boot-on;

@@ -38,7 +38,7 @@

 	v12_poe: v12-poe-regulator {
 		compatible = "regulator-fixed";
-		reglator-name = "v12_poe";
+		regulator-name = "v12_poe";
 		regulator-always-on;
 		regulator-boot-on;

--- a/arch/arm64/boot/dts/qcom/msm8916-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-mtp.dts
@@ -5,9 +5,22 @@

 /dts-v1/;

-#include "msm8916-mtp.dtsi"
+#include "msm8916-pm8916.dtsi"

 / {
 	model = "Qualcomm Technologies, Inc. MSM 8916 MTP";
 	compatible = "qcom,msm8916-mtp", "qcom,msm8916-mtp/1", "qcom,msm8916";
+
+	aliases {
+		serial0 = &blsp1_uart2;
+		usid0 = &pm8916_0;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
 };
--- a/arch/arm64/boot/dts/qcom/msm8916-mtp.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916-mtp.dtsi
@@ -1,21 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (c) 2014-2015, The Linux Foundation. All rights reserved.
- */
-
-#include "msm8916-pm8916.dtsi"
-
-/ {
-	aliases {
-		serial0 = &blsp1_uart2;
-		usid0 = &pm8916_0;
-	};
-
-	chosen {
-		stdout-path = "serial0";
-	};
-};
-
-&blsp1_uart2 {
-	status = "okay";
-};
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -1064,7 +1064,7 @@
 			};
 		};

-		camss: camss@1b00000 {
+		camss: camss@1b0ac00 {
 			compatible = "qcom,msm8916-camss";
 			reg = <0x01b0ac00 0x200>,
 				<0x01b00030 0x4>,
@@ -1771,7 +1771,7 @@

 				label = "pronto";

-				wcnss {
+				wcnss_ctrl: wcnss {
 					compatible = "qcom,wcnss";
 					qcom,smd-channels = "WCNSS_CTRL";

--- a/arch/arm64/boot/dts/qcom/msm8994.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi
@@ -725,7 +725,7 @@
 			reg = <0xfc4ab000 0x4>;
 		};

-		spmi_bus: spmi@fc4c0000 {
+		spmi_bus: spmi@fc4cf000 {
 			compatible = "qcom,spmi-pmic-arb";
 			reg = <0xfc4cf000 0x1000>,
 			      <0xfc4cb000 0x1000>,
--- a/arch/arm64/boot/dts/qcom/msm8996-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/msm8996-mtp.dts
@@ -5,9 +5,31 @@

 /dts-v1/;

-#include "msm8996-mtp.dtsi"
+#include "msm8996.dtsi"

 / {
 	model = "Qualcomm Technologies, Inc. MSM 8996 MTP";
 	compatible = "qcom,msm8996-mtp";
+
+	aliases {
+		serial0 = &blsp2_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	soc {
+		serial@75b0000 {
+			status = "okay";
+		};
+	};
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_phy {
+	status = "okay";
 };
--- a/arch/arm64/boot/dts/qcom/msm8996-mtp.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996-mtp.dtsi
@@ -1,30 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (c) 2014-2015, The Linux Foundation. All rights reserved.
- */
-
-#include "msm8996.dtsi"
-
-/ {
-	aliases {
-		serial0 = &blsp2_uart2;
-	};
-
-	chosen {
-		stdout-path = "serial0";
-	};
-
-	soc {
-		serial@75b0000 {
-			status = "okay";
-		};
-	};
-};
-
-&hdmi {
-	status = "okay";
-};
-
-&hdmi_phy {
-	status = "okay";
-};
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -1228,6 +1228,20 @@
 				};
 			};

+			blsp1_uart2_default: blsp1-uart2-default {
+				pins = "gpio41", "gpio42", "gpio43", "gpio44";
+				function = "blsp_uart2";
+				drive-strength = <16>;
+				bias-disable;
+			};
+
+			blsp1_uart2_sleep: blsp1-uart2-sleep {
+				pins = "gpio41", "gpio42", "gpio43", "gpio44";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
 			blsp1_i2c3_default: blsp1-i2c2-default {
 				pins = "gpio47", "gpio48";
 				function = "blsp_i2c3";
@@ -1771,7 +1785,7 @@
 			};
 		};

-		camss: camss@a00000 {
+		camss: camss@a34000 {
 			compatible = "qcom,msm8996-camss";
 			reg = <0x00a34000 0x1000>,
 			      <0x00a00030 0x4>,
@@ -2724,6 +2738,9 @@
 			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_uart2_default>;
+			pinctrl-1 = <&blsp1_uart2_sleep>;
 			dmas = <&blsp1_dma 2>, <&blsp1_dma 3>;
 			dma-names = "tx", "rx";
 			status = "disabled";
--- a/arch/arm64/boot/dts/qcom/sdm630.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm630.dtsi
@@ -1834,7 +1834,7 @@
 			};
 		};

-		camss: camss@ca00000 {
+		camss: camss@ca00020 {
 			compatible = "qcom,sdm660-camss";
 			reg = <0x0c824000 0x1000>,
 			      <0x0ca00120 0x4>,
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -3921,7 +3921,7 @@
 			#reset-cells = <1>;
 		};

-		camss: camss@a00000 {
+		camss: camss@acb3000 {
 			compatible = "qcom,sdm845-camss";

 			reg = <0 0xacb3000 0 0x1000>,
--- a/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi
@@ -26,9 +26,10 @@
 		framebuffer: framebuffer@9c000000 {
 			compatible = "simple-framebuffer";
 			reg = <0 0x9c000000 0 0x2300000>;
-			width = <1644>;
-			height = <3840>;
-			stride = <(1644 * 4)>;
+			/* pdx203 BL initializes in 2.5k mode, not 4k */
+			width = <1096>;
+			height = <2560>;
+			stride = <(1096 * 4)>;
 			format = "a8r8g8b8";
 			/*
 			 * That's a lot of clocks, but it's necessary due
--- a/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi
+++ b/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi
@@ -270,7 +270,7 @@
 	};

 	scif1_pins: scif1 {
-		groups = "scif1_data_b", "scif1_ctrl";
+		groups = "scif1_data_b";
 		function = "scif1";
 	};

@@ -330,7 +330,6 @@
 &scif1 {
 	pinctrl-0 = <&scif1_pins>;
 	pinctrl-names = "default";
-	uart-has-rtscts;

 	status = "okay";
 };
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -80,25 +80,25 @@
 &wkup_pmx2 {
 	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
 		pinctrl-single,pins = <
-			J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
-			J721E_WKUP_IOPAD(0x006c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
-			J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
-			J721E_WKUP_IOPAD(0x0074, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
-			J721E_WKUP_IOPAD(0x0078, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
-			J721E_WKUP_IOPAD(0x007c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
-			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
-			J721E_WKUP_IOPAD(0x008c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
-			J721E_WKUP_IOPAD(0x0090, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
-			J721E_WKUP_IOPAD(0x0094, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
-			J721E_WKUP_IOPAD(0x0080, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
-			J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
+			J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
+			J721E_WKUP_IOPAD(0x0004, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
+			J721E_WKUP_IOPAD(0x0008, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
+			J721E_WKUP_IOPAD(0x000c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
+			J721E_WKUP_IOPAD(0x0010, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
+			J721E_WKUP_IOPAD(0x0014, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
+			J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
+			J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
+			J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
+			J721E_WKUP_IOPAD(0x002c, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
+			J721E_WKUP_IOPAD(0x0018, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
+			J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
 		>;
 	};

 	mcu_mdio_pins_default: mcu-mdio1-pins-default {
 		pinctrl-single,pins = <
-			J721E_WKUP_IOPAD(0x009c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
-			J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
+			J721E_WKUP_IOPAD(0x0034, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
+			J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
 		>;
 	};
 };
--- a/arch/mips/include/asm/kvm_host.h
+++ b/arch/mips/include/asm/kvm_host.h
@@ -318,7 +318,7 @@ struct kvm_vcpu_arch {
 	unsigned int aux_inuse;

 	/* COP0 State */
-	struct mips_coproc *cop0;
+	struct mips_coproc cop0;

 	/* Resume PC after MMIO completion */
 	unsigned long io_pc;
@@ -699,7 +699,7 @@ static inline bool kvm_mips_guest_can_have_fpu(struct kvm_vcpu_arch *vcpu)
 static inline bool kvm_mips_guest_has_fpu(struct kvm_vcpu_arch *vcpu)
 {
 	return kvm_mips_guest_can_have_fpu(vcpu) &&
-		kvm_read_c0_guest_config1(vcpu->cop0) & MIPS_CONF1_FP;
+		kvm_read_c0_guest_config1(&vcpu->cop0) & MIPS_CONF1_FP;
 }

 static inline bool kvm_mips_guest_can_have_msa(struct kvm_vcpu_arch *vcpu)
@@ -711,7 +711,7 @@ static inline bool kvm_mips_guest_can_have_msa(struct kvm_vcpu_arch *vcpu)
 static inline bool kvm_mips_guest_has_msa(struct kvm_vcpu_arch *vcpu)
 {
 	return kvm_mips_guest_can_have_msa(vcpu) &&
-		kvm_read_c0_guest_config3(vcpu->cop0) & MIPS_CONF3_MSA;
+		kvm_read_c0_guest_config3(&vcpu->cop0) & MIPS_CONF3_MSA;
 }

 struct kvm_mips_callbacks {
--- a/arch/mips/kernel/cpu-probe.c
+++ b/arch/mips/kernel/cpu-probe.c
@@ -1734,7 +1734,10 @@ static inline void decode_cpucfg(struct cpuinfo_mips *c)

 static inline void cpu_probe_loongson(struct cpuinfo_mips *c, unsigned int cpu)
 {
+	c->cputype = CPU_LOONGSON64;
+
 	/* All Loongson processors covered here define ExcCode 16 as GSExc. */
+	decode_configs(c);
 	c->options |= MIPS_CPU_GSEXCEX;

 	switch (c->processor_id & PRID_IMP_MASK) {
@@ -1744,7 +1747,6 @@ static inline void cpu_probe_loongson(struct cpuinfo_mips *c, unsigned int cpu)
 		case PRID_REV_LOONGSON2K_R1_1:
 		case PRID_REV_LOONGSON2K_R1_2:
 		case PRID_REV_LOONGSON2K_R1_3:
-			c->cputype = CPU_LOONGSON64;
 			__cpu_name[cpu] = "Loongson-2K";
 			set_elf_platform(cpu, "gs264e");
 			set_isa(c, MIPS_CPU_ISA_M64R2);
@@ -1757,14 +1759,12 @@ static inline void cpu_probe_loongson(struct cpuinfo_mips *c, unsigned int cpu)
 		switch (c->processor_id & PRID_REV_MASK) {
 		case PRID_REV_LOONGSON3A_R2_0:
 		case PRID_REV_LOONGSON3A_R2_1:
-			c->cputype = CPU_LOONGSON64;
 			__cpu_name[cpu] = "ICT Loongson-3";
 			set_elf_platform(cpu, "loongson3a");
 			set_isa(c, MIPS_CPU_ISA_M64R2);
 			break;
 		case PRID_REV_LOONGSON3A_R3_0:
 		case PRID_REV_LOONGSON3A_R3_1:
-			c->cputype = CPU_LOONGSON64;
 			__cpu_name[cpu] = "ICT Loongson-3";
 			set_elf_platform(cpu, "loongson3a");
 			set_isa(c, MIPS_CPU_ISA_M64R2);
@@ -1784,7 +1784,6 @@ static inline void cpu_probe_loongson(struct cpuinfo_mips *c, unsigned int cpu)
 		c->ases &= ~MIPS_ASE_VZ; /* VZ of Loongson-3A2000/3000 is incomplete */
 		break;
 	case PRID_IMP_LOONGSON_64G:
-		c->cputype = CPU_LOONGSON64;
 		__cpu_name[cpu] = "ICT Loongson-3";
 		set_elf_platform(cpu, "loongson3a");
 		set_isa(c, MIPS_CPU_ISA_M64R2);
@@ -1794,8 +1793,6 @@ static inline void cpu_probe_loongson(struct cpuinfo_mips *c, unsigned int cpu)
 		panic("Unknown Loongson Processor ID!");
 		break;
 	}
-
-	decode_configs(c);
 }
 #else
 static inline void cpu_probe_loongson(struct cpuinfo_mips *c, unsigned int cpu) { }
--- a/arch/mips/kvm/emulate.c
+++ b/arch/mips/kvm/emulate.c
@@ -312,7 +312,7 @@ int kvm_get_badinstrp(u32 *opc, struct kvm_vcpu *vcpu, u32 *out)
 */
 int kvm_mips_count_disabled(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;

 	return	(vcpu->arch.count_ctl & KVM_REG_MIPS_COUNT_CTL_DC) ||
 		(kvm_read_c0_guest_cause(cop0) & CAUSEF_DC);
@@ -384,7 +384,7 @@ static inline ktime_t kvm_mips_count_time(struct kvm_vcpu *vcpu)
 */
 static u32 kvm_mips_read_count_running(struct kvm_vcpu *vcpu, ktime_t now)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	ktime_t expires, threshold;
 	u32 count, compare;
 	int running;
@@ -444,7 +444,7 @@ static u32 kvm_mips_read_count_running(struct kvm_vcpu *vcpu, ktime_t now)
 */
 u32 kvm_mips_read_count(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;

 	/* If count disabled just read static copy of count */
 	if (kvm_mips_count_disabled(vcpu))
@@ -502,7 +502,7 @@ ktime_t kvm_mips_freeze_hrtimer(struct kvm_vcpu *vcpu, u32 *count)
 static void kvm_mips_resume_hrtimer(struct kvm_vcpu *vcpu,
 				    ktime_t now, u32 count)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	u32 compare;
 	u64 delta;
 	ktime_t expire;
@@ -603,7 +603,7 @@ resume:
 */
 void kvm_mips_write_count(struct kvm_vcpu *vcpu, u32 count)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	ktime_t now;

 	/* Calculate bias */
@@ -649,7 +649,7 @@ void kvm_mips_init_count(struct kvm_vcpu *vcpu, unsigned long count_hz)
 */
 int kvm_mips_set_count_hz(struct kvm_vcpu *vcpu, s64 count_hz)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	int dc;
 	ktime_t now;
 	u32 count;
@@ -696,7 +696,7 @@ int kvm_mips_set_count_hz(struct kvm_vcpu *vcpu, s64 count_hz)
 */
 void kvm_mips_write_compare(struct kvm_vcpu *vcpu, u32 compare, bool ack)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	int dc;
 	u32 old_compare = kvm_read_c0_guest_compare(cop0);
 	s32 delta = compare - old_compare;
@@ -779,7 +779,7 @@ void kvm_mips_write_compare(struct kvm_vcpu *vcpu, u32 compare, bool ack)
 */
 static ktime_t kvm_mips_count_disable(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	u32 count;
 	ktime_t now;

@@ -806,7 +806,7 @@ static ktime_t kvm_mips_count_disable(struct kvm_vcpu *vcpu)
 */
 void kvm_mips_count_disable_cause(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;

 	kvm_set_c0_guest_cause(cop0, CAUSEF_DC);
 	if (!(vcpu->arch.count_ctl & KVM_REG_MIPS_COUNT_CTL_DC))
@@ -826,7 +826,7 @@ void kvm_mips_count_disable_cause(struct kvm_vcpu *vcpu)
 */
 void kvm_mips_count_enable_cause(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	u32 count;

 	kvm_clear_c0_guest_cause(cop0, CAUSEF_DC);
@@ -852,7 +852,7 @@ void kvm_mips_count_enable_cause(struct kvm_vcpu *vcpu)
 */
 int kvm_mips_set_count_ctl(struct kvm_vcpu *vcpu, s64 count_ctl)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	s64 changed = count_ctl ^ vcpu->arch.count_ctl;
 	s64 delta;
 	ktime_t expire, now;
--- a/arch/mips/kvm/mips.c
+++ b/arch/mips/kvm/mips.c
@@ -633,7 +633,7 @@ static int kvm_mips_copy_reg_indices(struct kvm_vcpu *vcpu, u64 __user *indices)
 static int kvm_mips_get_reg(struct kvm_vcpu *vcpu,
 			    const struct kvm_one_reg *reg)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	struct mips_fpu_struct *fpu = &vcpu->arch.fpu;
 	int ret;
 	s64 v;
@@ -745,7 +745,7 @@ static int kvm_mips_get_reg(struct kvm_vcpu *vcpu,
 static int kvm_mips_set_reg(struct kvm_vcpu *vcpu,
 			    const struct kvm_one_reg *reg)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	struct mips_fpu_struct *fpu = &vcpu->arch.fpu;
 	s64 v;
 	s64 vs[2];
@@ -1085,7 +1085,7 @@ int kvm_vm_ioctl_check_extension(struct kvm *kvm, long ext)
 int kvm_cpu_has_pending_timer(struct kvm_vcpu *vcpu)
 {
 	return kvm_mips_pending_timer(vcpu) ||
-		kvm_read_c0_guest_cause(vcpu->arch.cop0) & C_TI;
+		kvm_read_c0_guest_cause(&vcpu->arch.cop0) & C_TI;
 }

 int kvm_arch_vcpu_dump_regs(struct kvm_vcpu *vcpu)
@@ -1109,7 +1109,7 @@ int kvm_arch_vcpu_dump_regs(struct kvm_vcpu *vcpu)
 	kvm_debug("\thi: 0x%08lx\n", vcpu->arch.hi);
 	kvm_debug("\tlo: 0x%08lx\n", vcpu->arch.lo);

-	cop0 = vcpu->arch.cop0;
+	cop0 = &vcpu->arch.cop0;
 	kvm_debug("\tStatus: 0x%08x, Cause: 0x%08x\n",
 		  kvm_read_c0_guest_status(cop0),
 		  kvm_read_c0_guest_cause(cop0));
@@ -1231,7 +1231,7 @@ int kvm_mips_handle_exit(struct kvm_vcpu *vcpu)

 	case EXCCODE_TLBS:
 		kvm_debug("TLB ST fault:  cause %#x, status %#x, PC: %p, BadVaddr: %#lx\n",
-			  cause, kvm_read_c0_guest_status(vcpu->arch.cop0), opc,
+			  cause, kvm_read_c0_guest_status(&vcpu->arch.cop0), opc,
 			  badvaddr);

 		++vcpu->stat.tlbmiss_st_exits;
@@ -1303,7 +1303,7 @@ int kvm_mips_handle_exit(struct kvm_vcpu *vcpu)
 		kvm_get_badinstr(opc, vcpu, &inst);
 		kvm_err("Exception Code: %d, not yet handled, @ PC: %p, inst: 0x%08x  BadVaddr: %#lx Status: %#x\n",
 			exccode, opc, inst, badvaddr,
-			kvm_read_c0_guest_status(vcpu->arch.cop0));
+			kvm_read_c0_guest_status(&vcpu->arch.cop0));
 		kvm_arch_vcpu_dump_regs(vcpu);
 		run->exit_reason = KVM_EXIT_INTERNAL_ERROR;
 		ret = RESUME_HOST;
@@ -1365,7 +1365,7 @@ int kvm_mips_handle_exit(struct kvm_vcpu *vcpu)
 /* Enable FPU for guest and restore context */
 void kvm_own_fpu(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	unsigned int sr, cfg5;

 	preempt_disable();
@@ -1409,7 +1409,7 @@ void kvm_own_fpu(struct kvm_vcpu *vcpu)
 /* Enable MSA for guest and restore context */
 void kvm_own_msa(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	unsigned int sr, cfg5;

 	preempt_disable();
--- a/arch/mips/kvm/stats.c
+++ b/arch/mips/kvm/stats.c
@@ -54,9 +54,9 @@ void kvm_mips_dump_stats(struct kvm_vcpu *vcpu)
 	kvm_info("\nKVM VCPU[%d] COP0 Access Profile:\n", vcpu->vcpu_id);
 	for (i = 0; i < N_MIPS_COPROC_REGS; i++) {
 		for (j = 0; j < N_MIPS_COPROC_SEL; j++) {
-			if (vcpu->arch.cop0->stat[i][j])
+			if (vcpu->arch.cop0.stat[i][j])
 				kvm_info("%s[%d]: %lu\n", kvm_cop0_str[i], j,
-					 vcpu->arch.cop0->stat[i][j]);
+					 vcpu->arch.cop0.stat[i][j]);
 		}
 	}
 #endif
--- a/arch/mips/kvm/trace.h
+++ b/arch/mips/kvm/trace.h
@@ -322,11 +322,11 @@ TRACE_EVENT_FN(kvm_guest_mode_change,
 	    ),

 	    TP_fast_assign(
-			__entry->epc = kvm_read_c0_guest_epc(vcpu->arch.cop0);
+			__entry->epc = kvm_read_c0_guest_epc(&vcpu->arch.cop0);
 			__entry->pc = vcpu->arch.pc;
-			__entry->badvaddr = kvm_read_c0_guest_badvaddr(vcpu->arch.cop0);
-			__entry->status = kvm_read_c0_guest_status(vcpu->arch.cop0);
-			__entry->cause = kvm_read_c0_guest_cause(vcpu->arch.cop0);
+			__entry->badvaddr = kvm_read_c0_guest_badvaddr(&vcpu->arch.cop0);
+			__entry->status = kvm_read_c0_guest_status(&vcpu->arch.cop0);
+			__entry->cause = kvm_read_c0_guest_cause(&vcpu->arch.cop0);
 	    ),

 	    TP_printk("EPC: 0x%08lx PC: 0x%08lx Status: 0x%08x Cause: 0x%08x BadVAddr: 0x%08lx",
--- a/arch/mips/kvm/vz.c
+++ b/arch/mips/kvm/vz.c
@@ -422,7 +422,7 @@ static void _kvm_vz_restore_htimer(struct kvm_vcpu *vcpu,
 */
 static void kvm_vz_restore_timer(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	u32 cause, compare;

 	compare = kvm_read_sw_gc0_compare(cop0);
@@ -517,7 +517,7 @@ static void _kvm_vz_save_htimer(struct kvm_vcpu *vcpu,
 */
 static void kvm_vz_save_timer(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	u32 gctl0, compare, cause;

 	gctl0 = read_c0_guestctl0();
@@ -863,7 +863,7 @@ static unsigned long mips_process_maar(unsigned int op, unsigned long val)

 static void kvm_write_maari(struct kvm_vcpu *vcpu, unsigned long val)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;

 	val &= MIPS_MAARI_INDEX;
 	if (val == MIPS_MAARI_INDEX)
@@ -876,7 +876,7 @@ static enum emulation_result kvm_vz_gpsi_cop0(union mips_instruction inst,
 					      u32 *opc, u32 cause,
 					      struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	enum emulation_result er = EMULATE_DONE;
 	u32 rt, rd, sel;
 	unsigned long curr_pc;
@@ -1905,7 +1905,7 @@ static int kvm_vz_get_one_reg(struct kvm_vcpu *vcpu,
 			      const struct kvm_one_reg *reg,
 			      s64 *v)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	unsigned int idx;

 	switch (reg->id) {
@@ -2075,7 +2075,7 @@ static int kvm_vz_get_one_reg(struct kvm_vcpu *vcpu,
 	case KVM_REG_MIPS_CP0_MAARI:
 		if (!cpu_guest_has_maar || cpu_guest_has_dyn_maar)
 			return -EINVAL;
-		*v = kvm_read_sw_gc0_maari(vcpu->arch.cop0);
+		*v = kvm_read_sw_gc0_maari(&vcpu->arch.cop0);
 		break;
 #ifdef CONFIG_64BIT
 	case KVM_REG_MIPS_CP0_XCONTEXT:
@@ -2129,7 +2129,7 @@ static int kvm_vz_set_one_reg(struct kvm_vcpu *vcpu,
 			      const struct kvm_one_reg *reg,
 			      s64 v)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	unsigned int idx;
 	int ret = 0;
 	unsigned int cur, change;
@@ -2556,7 +2556,7 @@ static void kvm_vz_vcpu_load_tlb(struct kvm_vcpu *vcpu, int cpu)

 static int kvm_vz_vcpu_load(struct kvm_vcpu *vcpu, int cpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	bool migrated, all;

 	/*
@@ -2698,7 +2698,7 @@ static int kvm_vz_vcpu_load(struct kvm_vcpu *vcpu, int cpu)

 static int kvm_vz_vcpu_put(struct kvm_vcpu *vcpu, int cpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;

 	if (current->flags & PF_VCPU)
 		kvm_vz_vcpu_save_wired(vcpu);
@@ -3070,7 +3070,7 @@ static void kvm_vz_vcpu_uninit(struct kvm_vcpu *vcpu)

 static int kvm_vz_vcpu_setup(struct kvm_vcpu *vcpu)
 {
-	struct mips_coproc *cop0 = vcpu->arch.cop0;
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
 	unsigned long count_hz = 100*1000*1000; /* default to 100 MHz */

 	/*
--- a/arch/powerpc/Kconfig.debug
+++ b/arch/powerpc/Kconfig.debug
@@ -240,7 +240,7 @@ config PPC_EARLY_DEBUG_40x

 config PPC_EARLY_DEBUG_CPM
 	bool "Early serial debugging for Freescale CPM-based serial ports"
-	depends on SERIAL_CPM
+	depends on SERIAL_CPM=y
 	help
 	  Select this to enable early debugging for Freescale chips
 	  using a CPM-based serial port.  This assumes that the bootwrapper
--- a/arch/powerpc/Makefile
+++ b/arch/powerpc/Makefile
@@ -444,3 +444,11 @@ checkbin:
 		echo -n '*** Please use a different binutils version.' ; \
 		false ; \
 	fi
+	@if test "x${CONFIG_FTRACE_MCOUNT_USE_RECORDMCOUNT}" = "xy" -a \
+		"x${CONFIG_LD_IS_BFD}" = "xy" -a \
+		"${CONFIG_LD_VERSION}" = "23700" ; then \
+		echo -n '*** binutils 2.37 drops unused section symbols, which recordmcount ' ; \
+		echo 'is unable to handle.' ; \
+		echo '*** Please use a different binutils version.' ; \
+		false ; \
+	fi
--- a/arch/powerpc/kernel/interrupt.c
+++ b/arch/powerpc/kernel/interrupt.c
@@ -531,7 +531,6 @@ void preempt_schedule_irq(void);

 notrace unsigned long interrupt_exit_kernel_prepare(struct pt_regs *regs)
 {
-	unsigned long flags;
 	unsigned long ret = 0;
 	unsigned long kuap;
 	bool stack_store = current_thread_info()->flags &
@@ -548,7 +547,7 @@ notrace unsigned long interrupt_exit_kernel_prepare(struct pt_regs *regs)

 	kuap = kuap_get_and_assert_locked();

-	local_irq_save(flags);
+	local_irq_disable();

 	if (!arch_irq_disabled_regs(regs)) {
 		/* Returning to a kernel context with local irqs enabled. */
--- a/arch/powerpc/kernel/ppc_save_regs.S
+++ b/arch/powerpc/kernel/ppc_save_regs.S
@@ -21,60 +21,33 @@
 * different ABIs, though).
 */
 _GLOBAL(ppc_save_regs)
-	PPC_STL	r0,0*SZL(r3)
+	/* This allows stack frame accessor macros and offsets to be used */
+	subi	r3,r3,STACK_FRAME_OVERHEAD
+	PPC_STL	r0,GPR0(r3)
 #ifdef CONFIG_PPC32
-	stmw	r2, 2*SZL(r3)
+	stmw	r2,GPR2(r3)
 #else
-	PPC_STL	r2,2*SZL(r3)
-	PPC_STL	r3,3*SZL(r3)
-	PPC_STL	r4,4*SZL(r3)
-	PPC_STL	r5,5*SZL(r3)
-	PPC_STL	r6,6*SZL(r3)
-	PPC_STL	r7,7*SZL(r3)
-	PPC_STL	r8,8*SZL(r3)
-	PPC_STL	r9,9*SZL(r3)
-	PPC_STL	r10,10*SZL(r3)
-	PPC_STL	r11,11*SZL(r3)
-	PPC_STL	r12,12*SZL(r3)
-	PPC_STL	r13,13*SZL(r3)
-	PPC_STL	r14,14*SZL(r3)
-	PPC_STL	r15,15*SZL(r3)
-	PPC_STL	r16,16*SZL(r3)
-	PPC_STL	r17,17*SZL(r3)
-	PPC_STL	r18,18*SZL(r3)
-	PPC_STL	r19,19*SZL(r3)
-	PPC_STL	r20,20*SZL(r3)
-	PPC_STL	r21,21*SZL(r3)
-	PPC_STL	r22,22*SZL(r3)
-	PPC_STL	r23,23*SZL(r3)
-	PPC_STL	r24,24*SZL(r3)
-	PPC_STL	r25,25*SZL(r3)
-	PPC_STL	r26,26*SZL(r3)
-	PPC_STL	r27,27*SZL(r3)
-	PPC_STL	r28,28*SZL(r3)
-	PPC_STL	r29,29*SZL(r3)
-	PPC_STL	r30,30*SZL(r3)
-	PPC_STL	r31,31*SZL(r3)
+	SAVE_GPRS(2, 31, r3)
 	lbz	r0,PACAIRQSOFTMASK(r13)
-	PPC_STL	r0,SOFTE-STACK_FRAME_OVERHEAD(r3)
+	PPC_STL	r0,SOFTE(r3)
 #endif
-	/* go up one stack frame for SP */
-	PPC_LL	r4,0(r1)
-	PPC_STL	r4,1*SZL(r3)
+	/* store current SP */
+	PPC_STL	r1,GPR1(r3)
 	/* get caller's LR */
+	PPC_LL	r4,0(r1)
 	PPC_LL	r0,LRSAVE(r4)
-	PPC_STL	r0,_LINK-STACK_FRAME_OVERHEAD(r3)
+	PPC_STL	r0,_LINK(r3)
 	mflr	r0
-	PPC_STL	r0,_NIP-STACK_FRAME_OVERHEAD(r3)
+	PPC_STL	r0,_NIP(r3)
 	mfmsr	r0
-	PPC_STL	r0,_MSR-STACK_FRAME_OVERHEAD(r3)
+	PPC_STL	r0,_MSR(r3)
 	mfctr	r0
-	PPC_STL	r0,_CTR-STACK_FRAME_OVERHEAD(r3)
+	PPC_STL	r0,_CTR(r3)
 	mfxer	r0
-	PPC_STL	r0,_XER-STACK_FRAME_OVERHEAD(r3)
+	PPC_STL	r0,_XER(r3)
 	mfcr	r0
-	PPC_STL	r0,_CCR-STACK_FRAME_OVERHEAD(r3)
+	PPC_STL	r0,_CCR(r3)
 	li	r0,0
-	PPC_STL	r0,_TRAP-STACK_FRAME_OVERHEAD(r3)
-	PPC_STL	r0,ORIG_GPR3-STACK_FRAME_OVERHEAD(r3)
+	PPC_STL	r0,_TRAP(r3)
+	PPC_STL	r0,ORIG_GPR3(r3)
 	blr
--- a/arch/powerpc/kernel/security.c
+++ b/arch/powerpc/kernel/security.c
@@ -363,26 +363,27 @@ ssize_t cpu_show_spec_store_bypass(struct device *dev, struct device_attribute *

 static int ssb_prctl_get(struct task_struct *task)
 {
-	if (stf_enabled_flush_types == STF_BARRIER_NONE)
-		/*
-		 * We don't have an explicit signal from firmware that we're
-		 * vulnerable or not, we only have certain CPU revisions that
-		 * are known to be vulnerable.
-		 *
-		 * We assume that if we're on another CPU, where the barrier is
-		 * NONE, then we are not vulnerable.
-		 */
+	/*
+	 * The STF_BARRIER feature is on by default, so if it's off that means
+	 * firmware has explicitly said the CPU is not vulnerable via either
+	 * the hypercall or device tree.
+	 */
+	if (!security_ftr_enabled(SEC_FTR_STF_BARRIER))
 		return PR_SPEC_NOT_AFFECTED;
-	else
-		/*
-		 * If we do have a barrier type then we are vulnerable. The
-		 * barrier is not a global or per-process mitigation, so the
-		 * only value we can report here is PR_SPEC_ENABLE, which
-		 * appears as "vulnerable" in /proc.
-		 */
-		return PR_SPEC_ENABLE;

-	return -EINVAL;
+	/*
+	 * If the system's CPU has no known barrier (see setup_stf_barrier())
+	 * then assume that the CPU is not vulnerable.
+	 */
+	if (stf_enabled_flush_types == STF_BARRIER_NONE)
+		return PR_SPEC_NOT_AFFECTED;
+
+	/*
+	 * Otherwise the CPU is vulnerable. The barrier is not a global or
+	 * per-process mitigation, so the only value that can be reported here
+	 * is PR_SPEC_ENABLE, which appears as "vulnerable" in /proc.
+	 */
+	return PR_SPEC_ENABLE;
 }

 int arch_prctl_spec_ctrl_get(struct task_struct *task, unsigned long which)
--- a/arch/powerpc/kernel/signal_32.c
+++ b/arch/powerpc/kernel/signal_32.c
@@ -258,8 +258,9 @@ static void prepare_save_user_regs(int ctx_has_vsx_region)
 #endif
 }

-static int __unsafe_save_user_regs(struct pt_regs *regs, struct mcontext __user *frame,
-				   struct mcontext __user *tm_frame, int ctx_has_vsx_region)
+static __always_inline int
+__unsafe_save_user_regs(struct pt_regs *regs, struct mcontext __user *frame,
+			struct mcontext __user *tm_frame, int ctx_has_vsx_region)
 {
 	unsigned long msr = regs->msr;

@@ -358,8 +359,9 @@ static void prepare_save_tm_user_regs(void)
 		current->thread.ckvrsave = mfspr(SPRN_VRSAVE);
 }

-static int save_tm_user_regs_unsafe(struct pt_regs *regs, struct mcontext __user *frame,
-				    struct mcontext __user *tm_frame, unsigned long msr)
+static __always_inline int
+save_tm_user_regs_unsafe(struct pt_regs *regs, struct mcontext __user *frame,
+			 struct mcontext __user *tm_frame, unsigned long msr)
 {
 	/* Save both sets of general registers */
 	unsafe_save_general_regs(&current->thread.ckpt_regs, frame, failed);
@@ -438,8 +440,9 @@ failed:
 #else
 static void prepare_save_tm_user_regs(void) { }

-static int save_tm_user_regs_unsafe(struct pt_regs *regs, struct mcontext __user *frame,
-				    struct mcontext __user *tm_frame, unsigned long msr)
+static __always_inline int
+save_tm_user_regs_unsafe(struct pt_regs *regs, struct mcontext __user *frame,
+			 struct mcontext __user *tm_frame, unsigned long msr)
 {
 	return 0;
 }
--- a/arch/powerpc/mm/book3s64/radix_pgtable.c
+++ b/arch/powerpc/mm/book3s64/radix_pgtable.c
@@ -764,9 +764,9 @@ static void free_pud_table(pud_t *pud_start, p4d_t *p4d)
 }

 static void remove_pte_table(pte_t *pte_start, unsigned long addr,
-			     unsigned long end)
+			     unsigned long end, bool direct)
 {
-	unsigned long next;
+	unsigned long next, pages = 0;
 	pte_t *pte;

 	pte = pte_start + pte_index(addr);
@@ -788,13 +788,16 @@ static void remove_pte_table(pte_t *pte_start, unsigned long addr,
 		}

 		pte_clear(&init_mm, addr, pte);
+		pages++;
 	}
+	if (direct)
+		update_page_count(mmu_virtual_psize, -pages);
 }

 static void __meminit remove_pmd_table(pmd_t *pmd_start, unsigned long addr,
-			     unsigned long end)
+				       unsigned long end, bool direct)
 {
-	unsigned long next;
+	unsigned long next, pages = 0;
 	pte_t *pte_base;
 	pmd_t *pmd;

@@ -812,19 +815,22 @@ static void __meminit remove_pmd_table(pmd_t *pmd_start, unsigned long addr,
 				continue;
 			}
 			pte_clear(&init_mm, addr, (pte_t *)pmd);
+			pages++;
 			continue;
 		}

 		pte_base = (pte_t *)pmd_page_vaddr(*pmd);
-		remove_pte_table(pte_base, addr, next);
+		remove_pte_table(pte_base, addr, next, direct);
 		free_pte_table(pte_base, pmd);
 	}
+	if (direct)
+		update_page_count(MMU_PAGE_2M, -pages);
 }

 static void __meminit remove_pud_table(pud_t *pud_start, unsigned long addr,
-			     unsigned long end)
+				       unsigned long end, bool direct)
 {
-	unsigned long next;
+	unsigned long next, pages = 0;
 	pmd_t *pmd_base;
 	pud_t *pud;

@@ -842,16 +848,20 @@ static void __meminit remove_pud_table(pud_t *pud_start, unsigned long addr,
 				continue;
 			}
 			pte_clear(&init_mm, addr, (pte_t *)pud);
+			pages++;
 			continue;
 		}

 		pmd_base = pud_pgtable(*pud);
-		remove_pmd_table(pmd_base, addr, next);
+		remove_pmd_table(pmd_base, addr, next, direct);
 		free_pmd_table(pmd_base, pud);
 	}
+	if (direct)
+		update_page_count(MMU_PAGE_1G, -pages);
 }

-static void __meminit remove_pagetable(unsigned long start, unsigned long end)
+static void __meminit remove_pagetable(unsigned long start, unsigned long end,
+				       bool direct)
 {
 	unsigned long addr, next;
 	pud_t *pud_base;
@@ -880,7 +890,7 @@ static void __meminit remove_pagetable(unsigned long start, unsigned long end)
 		}

 		pud_base = p4d_pgtable(*p4d);
-		remove_pud_table(pud_base, addr, next);
+		remove_pud_table(pud_base, addr, next, direct);
 		free_pud_table(pud_base, p4d);
 	}

@@ -903,7 +913,7 @@ int __meminit radix__create_section_mapping(unsigned long start,

 int __meminit radix__remove_section_mapping(unsigned long start, unsigned long end)
 {
-	remove_pagetable(start, end);
+	remove_pagetable(start, end, true);
 	return 0;
 }
 #endif /* CONFIG_MEMORY_HOTPLUG */
@@ -939,7 +949,7 @@ int __meminit radix__vmemmap_create_mapping(unsigned long start,
 #ifdef CONFIG_MEMORY_HOTPLUG
 void __meminit radix__vmemmap_remove_mapping(unsigned long start, unsigned long page_size)
 {
-	remove_pagetable(start, start + page_size);
+	remove_pagetable(start, start + page_size, false);
 }
 #endif
 #endif
--- a/arch/powerpc/mm/init_64.c
+++ b/arch/powerpc/mm/init_64.c
@@ -188,7 +188,7 @@ static bool altmap_cross_boundary(struct vmem_altmap *altmap, unsigned long star
 	unsigned long nr_pfn = page_size / sizeof(struct page);
 	unsigned long start_pfn = page_to_pfn((struct page *)start);

-	if ((start_pfn + nr_pfn) > altmap->end_pfn)
+	if ((start_pfn + nr_pfn - 1) > altmap->end_pfn)
 		return true;

 	if (start_pfn < altmap->base_pfn)
--- a/arch/powerpc/platforms/powernv/pci-sriov.c
+++ b/arch/powerpc/platforms/powernv/pci-sriov.c
@@ -600,12 +600,12 @@ static void pnv_pci_sriov_disable(struct pci_dev *pdev)
 	struct pnv_iov_data   *iov;

 	iov = pnv_iov_get(pdev);
-	num_vfs = iov->num_vfs;
-	base_pe = iov->vf_pe_arr[0].pe_number;
-
 	if (WARN_ON(!iov))
 		return;

+	num_vfs = iov->num_vfs;
+	base_pe = iov->vf_pe_arr[0].pe_number;
+
 	/* Release VF PEs */
 	pnv_ioda_release_vf_PE(pdev);

--- a/arch/powerpc/platforms/powernv/vas-window.c
+++ b/arch/powerpc/platforms/powernv/vas-window.c
@@ -1310,8 +1310,8 @@ int vas_win_close(struct vas_window *vwin)
 	/* if send window, drop reference to matching receive window */
 	if (window->tx_win) {
 		if (window->user_win) {
-			put_vas_user_win_ref(&vwin->task_ref);
 			mm_context_remove_vas_window(vwin->task_ref.mm);
+			put_vas_user_win_ref(&vwin->task_ref);
 		}
 		put_rx_win(window->rxwin);
 	}
--- a/arch/powerpc/platforms/pseries/vas.c
+++ b/arch/powerpc/platforms/pseries/vas.c
@@ -441,8 +441,8 @@ static int vas_deallocate_window(struct vas_window *vwin)
 	atomic_dec(&caps->used_lpar_creds);
 	mutex_unlock(&vas_pseries_mutex);

-	put_vas_user_win_ref(&vwin->task_ref);
 	mm_context_remove_vas_window(vwin->task_ref.mm);
+	put_vas_user_win_ref(&vwin->task_ref);

 	kfree(win);
 	return 0;
--- a/arch/riscv/kernel/probes/uprobes.c
+++ b/arch/riscv/kernel/probes/uprobes.c
@@ -67,6 +67,7 @@ int arch_uprobe_post_xol(struct arch_uprobe *auprobe, struct pt_regs *regs)
 	struct uprobe_task *utask = current->utask;

 	WARN_ON_ONCE(current->thread.bad_cause != UPROBE_TRAP_NR);
+	current->thread.bad_cause = utask->autask.saved_cause;

 	instruction_pointer_set(regs, utask->vaddr + auprobe->insn_size);

@@ -102,6 +103,7 @@ void arch_uprobe_abort_xol(struct arch_uprobe *auprobe, struct pt_regs *regs)
 {
 	struct uprobe_task *utask = current->utask;

+	current->thread.bad_cause = utask->autask.saved_cause;
 	/*
 	 * Task has received a fatal signal, so reset back to probbed
 	 * address.
--- a/arch/riscv/mm/init.c
+++ b/arch/riscv/mm/init.c
@@ -235,7 +235,6 @@ static void __init setup_bootmem(void)
 	dma_contiguous_reserve(dma32_phys_limit);
 	if (IS_ENABLED(CONFIG_64BIT))
 		hugetlb_cma_reserve(PUD_SHIFT - PAGE_SHIFT);
-	memblock_allow_resize();
 }

 #ifdef CONFIG_MMU
@@ -844,7 +843,7 @@ static void __init reserve_crashkernel(void)
 	 */
 	crash_base = memblock_phys_alloc_range(crash_size, PMD_SIZE,
 					       search_start,
-					       min(search_end, (unsigned long) SZ_4G));
+					       min(search_end, (unsigned long)(SZ_4G - 1)));
 	if (crash_base == 0) {
 		/* Try again without restricting region to 32bit addressible memory */
 		crash_base = memblock_phys_alloc_range(crash_size, PMD_SIZE,
@@ -868,6 +867,9 @@ void __init paging_init(void)
 {
 	setup_bootmem();
 	setup_vm_final();
+
+	/* Depend on that Linear Mapping is ready */
+	memblock_allow_resize();
 }

 void __init misc_mem_init(void)
--- a/arch/riscv/net/bpf_jit.h
+++ b/arch/riscv/net/bpf_jit.h
@@ -69,6 +69,7 @@ struct rv_jit_context {
 	struct bpf_prog *prog;
 	u16 *insns;		/* RV insns */
 	int ninsns;
+	int prologue_len;
 	int epilogue_offset;
 	int *offset;		/* BPF to RV */
 	unsigned long flags;
@@ -214,8 +215,8 @@ static inline int rv_offset(int insn, int off, struct rv_jit_context *ctx)
 	int from, to;

 	off++; /* BPF branch is from PC+1, RV is from PC */
-	from = (insn > 0) ? ctx->offset[insn - 1] : 0;
-	to = (insn + off > 0) ? ctx->offset[insn + off - 1] : 0;
+	from = (insn > 0) ? ctx->offset[insn - 1] : ctx->prologue_len;
+	to = (insn + off > 0) ? ctx->offset[insn + off - 1] : ctx->prologue_len;
 	return ninsns_rvoff(to - from);
 }

--- a/arch/riscv/net/bpf_jit_core.c
+++ b/arch/riscv/net/bpf_jit_core.c
@@ -83,6 +83,12 @@ struct bpf_prog *bpf_int_jit_compile(struct bpf_prog *prog)
 		prog = orig_prog;
 		goto out_offset;
 	}
+
+	if (build_body(ctx, extra_pass, NULL)) {
+		prog = orig_prog;
+		goto out_offset;
+	}
+
 	for (i = 0; i < prog->len; i++) {
 		prev_ninsns += 32;
 		ctx->offset[i] = prev_ninsns;
@@ -91,11 +97,15 @@ struct bpf_prog *bpf_int_jit_compile(struct bpf_prog *prog)
 	for (i = 0; i < NR_JIT_ITERATIONS; i++) {
 		pass++;
 		ctx->ninsns = 0;
+
+		bpf_jit_build_prologue(ctx);
+		ctx->prologue_len = ctx->ninsns;
+
 		if (build_body(ctx, extra_pass, ctx->offset)) {
 			prog = orig_prog;
 			goto out_offset;
 		}
-		bpf_jit_build_prologue(ctx);
+
 		ctx->epilogue_offset = ctx->ninsns;
 		bpf_jit_build_epilogue(ctx);

@@ -154,6 +164,9 @@ skip_init_ctx:

 	if (!prog->is_func || extra_pass) {
 		bpf_jit_binary_lock_ro(jit_data->header);
+		for (i = 0; i < prog->len; i++)
+			ctx->offset[i] = ninsns_rvoff(ctx->offset[i]);
+		bpf_prog_fill_jited_linfo(prog, ctx->offset);
 out_offset:
 		kfree(ctx->offset);
 		kfree(jit_data);
--- a/arch/s390/Makefile
+++ b/arch/s390/Makefile
@@ -29,6 +29,7 @@ KBUILD_CFLAGS_DECOMPRESSOR += -fno-delete-null-pointer-checks -msoft-float -mbac
 KBUILD_CFLAGS_DECOMPRESSOR += -fno-asynchronous-unwind-tables
 KBUILD_CFLAGS_DECOMPRESSOR += -ffreestanding
 KBUILD_CFLAGS_DECOMPRESSOR += -fno-stack-protector
+KBUILD_CFLAGS_DECOMPRESSOR += -fPIE
 KBUILD_CFLAGS_DECOMPRESSOR += $(call cc-disable-warning, address-of-packed-member)
 KBUILD_CFLAGS_DECOMPRESSOR += $(if $(CONFIG_DEBUG_INFO),-g)
 KBUILD_CFLAGS_DECOMPRESSOR += $(if $(CONFIG_DEBUG_INFO_DWARF4), $(call cc-option, -gdwarf-4,))
--- a/arch/s390/kvm/diag.c
+++ b/arch/s390/kvm/diag.c
@@ -166,6 +166,7 @@ static int diag9c_forwarding_overrun(void)
 static int __diag_time_slice_end_directed(struct kvm_vcpu *vcpu)
 {
 	struct kvm_vcpu *tcpu;
+	int tcpu_cpu;
 	int tid;

 	tid = vcpu->run->s.regs.gprs[(vcpu->arch.sie_block->ipa & 0xf0) >> 4];
@@ -181,14 +182,15 @@ static int __diag_time_slice_end_directed(struct kvm_vcpu *vcpu)
 		goto no_yield;

 	/* target guest VCPU already running */
-	if (READ_ONCE(tcpu->cpu) >= 0) {
+	tcpu_cpu = READ_ONCE(tcpu->cpu);
+	if (tcpu_cpu >= 0) {
 		if (!diag9c_forwarding_hz || diag9c_forwarding_overrun())
 			goto no_yield;

 		/* target host CPU already running */
-		if (!vcpu_is_preempted(tcpu->cpu))
+		if (!vcpu_is_preempted(tcpu_cpu))
 			goto no_yield;
-		smp_yield_cpu(tcpu->cpu);
+		smp_yield_cpu(tcpu_cpu);
 		VCPU_EVENT(vcpu, 5,
 			   "diag time slice end directed to %d: yield forwarded",
 			   tid);
--- a/arch/s390/kvm/kvm-s390.c
+++ b/arch/s390/kvm/kvm-s390.c
@@ -2030,6 +2030,10 @@ static unsigned long kvm_s390_next_dirty_cmma(struct kvm_memslots *slots,
 		ms = slots->memslots + slotidx;
 		ofs = 0;
 	}
+
+	if (cur_gfn < ms->base_gfn)
+		ofs = 0;
+
 	ofs = find_next_bit(kvm_second_dirty_bitmap(ms), ms->npages, ofs);
 	while ((slotidx > 0) && (ofs >= ms->npages)) {
 		slotidx--;
--- a/arch/s390/kvm/vsie.c
+++ b/arch/s390/kvm/vsie.c
@@ -169,7 +169,8 @@ static int setup_apcb00(struct kvm_vcpu *vcpu, unsigned long *apcb_s,
 			    sizeof(struct kvm_s390_apcb0)))
 		return -EFAULT;

-	bitmap_and(apcb_s, apcb_s, apcb_h, sizeof(struct kvm_s390_apcb0));
+	bitmap_and(apcb_s, apcb_s, apcb_h,
+		   BITS_PER_BYTE * sizeof(struct kvm_s390_apcb0));

 	return 0;
 }
@@ -191,7 +192,8 @@ static int setup_apcb11(struct kvm_vcpu *vcpu, unsigned long *apcb_s,
 			    sizeof(struct kvm_s390_apcb1)))
 		return -EFAULT;

-	bitmap_and(apcb_s, apcb_s, apcb_h, sizeof(struct kvm_s390_apcb1));
+	bitmap_and(apcb_s, apcb_s, apcb_h,
+		   BITS_PER_BYTE * sizeof(struct kvm_s390_apcb1));

 	return 0;
 }
--- a/arch/sh/drivers/dma/dma-sh.c
+++ b/arch/sh/drivers/dma/dma-sh.c
@@ -18,6 +18,18 @@
 #include <cpu/dma-register.h>
 #include <cpu/dma.h>

+/*
+ * Some of the SoCs feature two DMAC modules. In such a case, the channels are
+ * distributed equally among them.
+ */
+#ifdef	SH_DMAC_BASE1
+#define	SH_DMAC_NR_MD_CH	(CONFIG_NR_ONCHIP_DMA_CHANNELS / 2)
+#else
+#define	SH_DMAC_NR_MD_CH	CONFIG_NR_ONCHIP_DMA_CHANNELS
+#endif
+
+#define	SH_DMAC_CH_SZ		0x10
+
 /*
 * Define the default configuration for dual address memory-memory transfer.
 * The 0x400 value represents auto-request, external->external.
@@ -29,7 +41,7 @@ static unsigned long dma_find_base(unsigned int chan)
 	unsigned long base = SH_DMAC_BASE0;

 #ifdef SH_DMAC_BASE1
-	if (chan >= 6)
+	if (chan >= SH_DMAC_NR_MD_CH)
 		base = SH_DMAC_BASE1;
 #endif

@@ -40,13 +52,13 @@ static unsigned long dma_base_addr(unsigned int chan)
 {
 	unsigned long base = dma_find_base(chan);

-	/* Normalize offset calculation */
-	if (chan >= 9)
-		chan -= 6;
-	if (chan >= 4)
-		base += 0x10;
+	chan = (chan % SH_DMAC_NR_MD_CH) * SH_DMAC_CH_SZ;

-	return base + (chan * 0x10);
+	/* DMAOR is placed inside the channel register space. Step over it. */
+	if (chan >= DMAOR)
+		base += SH_DMAC_CH_SZ;
+
+	return base + chan;
 }

 #ifdef CONFIG_SH_DMA_IRQ_MULTI
@@ -250,12 +262,11 @@ static int sh_dmac_get_dma_residue(struct dma_channel *chan)
 #define NR_DMAOR	1
 #endif

-/*
- * DMAOR bases are broken out amongst channel groups. DMAOR0 manages
- * channels 0 - 5, DMAOR1 6 - 11 (optional).
- */
-#define dmaor_read_reg(n)		__raw_readw(dma_find_base((n)*6))
-#define dmaor_write_reg(n, data)	__raw_writew(data, dma_find_base(n)*6)
+#define dmaor_read_reg(n)		__raw_readw(dma_find_base((n) * \
+						    SH_DMAC_NR_MD_CH) + DMAOR)
+#define dmaor_write_reg(n, data)	__raw_writew(data, \
+						     dma_find_base((n) * \
+						     SH_DMAC_NR_MD_CH) + DMAOR)

 static inline int dmaor_reset(int no)
 {
--- a/arch/sh/kernel/cpu/sh2/probe.c
+++ b/arch/sh/kernel/cpu/sh2/probe.c
@@ -21,7 +21,7 @@ static int __init scan_cache(unsigned long node, const char *uname,
 	if (!of_flat_dt_is_compatible(node, "jcore,cache"))
 		return 0;

-	j2_ccr_base = (u32 __iomem *)of_flat_dt_translate_address(node);
+	j2_ccr_base = ioremap(of_flat_dt_translate_address(node), 4);

 	return 1;
 }
--- a/arch/um/Makefile
+++ b/arch/um/Makefile
@@ -148,7 +148,7 @@ export LDFLAGS_vmlinux := $(LDFLAGS_EXECSTACK)
 # When cleaning we don't include .config, so we don't include
 # TT or skas makefiles and don't clean skas_ptregs.h.
 CLEAN_FILES += linux x.i gmon.out
-MRPROPER_FILES += arch/$(SUBARCH)/include/generated
+MRPROPER_FILES += $(HOST_DIR)/include/generated

 archclean:
 	@find . \( -name '*.bb' -o -name '*.bbg' -o -name '*.da' \
--- a/arch/xtensa/platforms/iss/network.c
+++ b/arch/xtensa/platforms/iss/network.c
@@ -231,7 +231,7 @@ static int tuntap_probe(struct iss_net_private *lp, int index, char *init)

 	init += sizeof(TRANSPORT_TUNTAP_NAME) - 1;
 	if (*init == ',') {
-		rem = split_if_spec(init + 1, &mac_str, &dev_name);
+		rem = split_if_spec(init + 1, &mac_str, &dev_name, NULL);
 		if (rem != NULL) {
 			pr_err("%s: extra garbage on specification : '%s'\n",
 			       dev->name, rem);
--- a/block/disk-events.c
+++ b/block/disk-events.c
@@ -307,6 +307,7 @@ bool disk_force_media_change(struct gendisk *disk, unsigned int events)
 	if (!(events & DISK_EVENT_MEDIA_CHANGE))
 		return false;

+	inc_diskseq(disk);
 	if (__invalidate_device(disk->part0, true))
 		pr_warn("VFS: busy inodes on changed media %s\n",
 			disk->disk_name);
--- a/block/partitions/amiga.c
+++ b/block/partitions/amiga.c
@@ -11,10 +11,18 @@
 #define pr_fmt(fmt) fmt

 #include <linux/types.h>
+#include <linux/mm_types.h>
+#include <linux/overflow.h>
 #include <linux/affs_hardblocks.h>

 #include "check.h"

+/* magic offsets in partition DosEnvVec */
+#define NR_HD	3
+#define NR_SECT	5
+#define LO_CYL	9
+#define HI_CYL	10
+
 static __inline__ u32
 checksum_block(__be32 *m, int size)
 {
@@ -31,8 +39,12 @@ int amiga_partition(struct parsed_partitions *state)
 	unsigned char *data;
 	struct RigidDiskBlock *rdb;
 	struct PartitionBlock *pb;
-	int start_sect, nr_sects, blk, part, res = 0;
-	int blksize = 1;	/* Multiplier for disk block size */
+	u64 start_sect, nr_sects;
+	sector_t blk, end_sect;
+	u32 cylblk;		/* rdb_CylBlocks = nr_heads*sect_per_track */
+	u32 nr_hd, nr_sect, lo_cyl, hi_cyl;
+	int part, res = 0;
+	unsigned int blksize = 1;	/* Multiplier for disk block size */
 	int slot = 1;

 	for (blk = 0; ; blk++, put_dev_sector(sect)) {
@@ -40,7 +52,7 @@ int amiga_partition(struct parsed_partitions *state)
 			goto rdb_done;
 		data = read_part_sector(state, blk, &sect);
 		if (!data) {
-			pr_err("Dev %s: unable to read RDB block %d\n",
+			pr_err("Dev %s: unable to read RDB block %llu\n",
 			       state->disk->disk_name, blk);
 			res = -1;
 			goto rdb_done;
@@ -57,12 +69,12 @@ int amiga_partition(struct parsed_partitions *state)
 		*(__be32 *)(data+0xdc) = 0;
 		if (checksum_block((__be32 *)data,
 				be32_to_cpu(rdb->rdb_SummedLongs) & 0x7F)==0) {
-			pr_err("Trashed word at 0xd0 in block %d ignored in checksum calculation\n",
+			pr_err("Trashed word at 0xd0 in block %llu ignored in checksum calculation\n",
 			       blk);
 			break;
 		}

-		pr_err("Dev %s: RDB in block %d has bad checksum\n",
+		pr_err("Dev %s: RDB in block %llu has bad checksum\n",
 		       state->disk->disk_name, blk);
 	}

@@ -78,11 +90,16 @@ int amiga_partition(struct parsed_partitions *state)
 	}
 	blk = be32_to_cpu(rdb->rdb_PartitionList);
 	put_dev_sector(sect);
-	for (part = 1; blk>0 && part<=16; part++, put_dev_sector(sect)) {
-		blk *= blksize;	/* Read in terms partition table understands */
+	for (part = 1; (s32) blk>0 && part<=16; part++, put_dev_sector(sect)) {
+		/* Read in terms partition table understands */
+		if (check_mul_overflow(blk, (sector_t) blksize, &blk)) {
+			pr_err("Dev %s: overflow calculating partition block %llu! Skipping partitions %u and beyond\n",
+				state->disk->disk_name, blk, part);
+			break;
+		}
 		data = read_part_sector(state, blk, &sect);
 		if (!data) {
-			pr_err("Dev %s: unable to read partition block %d\n",
+			pr_err("Dev %s: unable to read partition block %llu\n",
 			       state->disk->disk_name, blk);
 			res = -1;
 			goto rdb_done;
@@ -94,19 +111,70 @@ int amiga_partition(struct parsed_partitions *state)
 		if (checksum_block((__be32 *)pb, be32_to_cpu(pb->pb_SummedLongs) & 0x7F) != 0 )
 			continue;

-		/* Tell Kernel about it */
+		/* RDB gives us more than enough rope to hang ourselves with,
+		 * many times over (2^128 bytes if all fields max out).
+		 * Some careful checks are in order, so check for potential
+		 * overflows.
+		 * We are multiplying four 32 bit numbers to one sector_t!
+		 */
+
+		nr_hd   = be32_to_cpu(pb->pb_Environment[NR_HD]);
+		nr_sect = be32_to_cpu(pb->pb_Environment[NR_SECT]);
+
+		/* CylBlocks is total number of blocks per cylinder */
+		if (check_mul_overflow(nr_hd, nr_sect, &cylblk)) {
+			pr_err("Dev %s: heads*sects %u overflows u32, skipping partition!\n",
+				state->disk->disk_name, cylblk);
+			continue;
+		}
+
+		/* check for consistency with RDB defined CylBlocks */
+		if (cylblk > be32_to_cpu(rdb->rdb_CylBlocks)) {
+			pr_warn("Dev %s: cylblk %u > rdb_CylBlocks %u!\n",
+				state->disk->disk_name, cylblk,
+				be32_to_cpu(rdb->rdb_CylBlocks));
+		}
+
+		/* RDB allows for variable logical block size -
+		 * normalize to 512 byte blocks and check result.
+		 */
+
+		if (check_mul_overflow(cylblk, blksize, &cylblk)) {
+			pr_err("Dev %s: partition %u bytes per cyl. overflows u32, skipping partition!\n",
+				state->disk->disk_name, part);
+			continue;
+		}
+
+		/* Calculate partition start and end. Limit of 32 bit on cylblk
+		 * guarantees no overflow occurs if LBD support is enabled.
+		 */
+
+		lo_cyl = be32_to_cpu(pb->pb_Environment[LO_CYL]);
+		start_sect = ((u64) lo_cyl * cylblk);
+
+		hi_cyl = be32_to_cpu(pb->pb_Environment[HI_CYL]);
+		nr_sects = (((u64) hi_cyl - lo_cyl + 1) * cylblk);

-		nr_sects = (be32_to_cpu(pb->pb_Environment[10]) + 1 -
-			    be32_to_cpu(pb->pb_Environment[9])) *
-			   be32_to_cpu(pb->pb_Environment[3]) *
-			   be32_to_cpu(pb->pb_Environment[5]) *
-			   blksize;
 		if (!nr_sects)
 			continue;
-		start_sect = be32_to_cpu(pb->pb_Environment[9]) *
-			     be32_to_cpu(pb->pb_Environment[3]) *
-			     be32_to_cpu(pb->pb_Environment[5]) *
-			     blksize;
+
+		/* Warn user if partition end overflows u32 (AmigaDOS limit) */
+
+		if ((start_sect + nr_sects) > UINT_MAX) {
+			pr_warn("Dev %s: partition %u (%llu-%llu) needs 64 bit device support!\n",
+				state->disk->disk_name, part,
+				start_sect, start_sect + nr_sects);
+		}
+
+		if (check_add_overflow(start_sect, nr_sects, &end_sect)) {
+			pr_err("Dev %s: partition %u (%llu-%llu) needs LBD device support, skipping partition!\n",
+				state->disk->disk_name, part,
+				start_sect, end_sect);
+			continue;
+		}
+
+		/* Tell Kernel about it */
+
 		put_partition(state,slot++,start_sect,nr_sects);
 		{
 			/* Be even more informative to aid mounting */
--- a/drivers/bus/intel-ixp4xx-eb.c
+++ b/drivers/bus/intel-ixp4xx-eb.c
@@ -33,7 +33,7 @@
 #define IXP4XX_EXP_TIMING_STRIDE	0x04
 #define IXP4XX_EXP_CS_EN		BIT(31)
 #define IXP456_EXP_PAR_EN		BIT(30) /* Only on IXP45x and IXP46x */
-#define IXP4XX_EXP_T1_MASK		GENMASK(28, 27)
+#define IXP4XX_EXP_T1_MASK		GENMASK(29, 28)
 #define IXP4XX_EXP_T1_SHIFT		28
 #define IXP4XX_EXP_T2_MASK		GENMASK(27, 26)
 #define IXP4XX_EXP_T2_SHIFT		26
--- a/drivers/bus/ti-sysc.c
+++ b/drivers/bus/ti-sysc.c
@@ -1759,7 +1759,7 @@ static u32 sysc_quirk_dispc(struct sysc *ddata, int dispc_offset,
 	if (!ddata->module_va)
 		return -EIO;

-	/* DISP_CONTROL */
+	/* DISP_CONTROL, shut down lcd and digit on disable if enabled */
 	val = sysc_read(ddata, dispc_offset + 0x40);
 	lcd_en = val & lcd_en_mask;
 	digit_en = val & digit_en_mask;
@@ -1771,7 +1771,7 @@ static u32 sysc_quirk_dispc(struct sysc *ddata, int dispc_offset,
 		else
 			irq_mask |= BIT(2) | BIT(3);	/* EVSYNC bits */
 	}
-	if (disable & (lcd_en | digit_en))
+	if (disable && (lcd_en || digit_en))
 		sysc_write(ddata, dispc_offset + 0x40,
 			   val & ~(lcd_en_mask | digit_en_mask));

--- a/drivers/char/hw_random/imx-rngc.c
+++ b/drivers/char/hw_random/imx-rngc.c
@@ -110,7 +110,7 @@ static int imx_rngc_self_test(struct imx_rngc *rngc)
 	cmd = readl(rngc->base + RNGC_COMMAND);
 	writel(cmd | RNGC_CMD_SELF_TEST, rngc->base + RNGC_COMMAND);

-	ret = wait_for_completion_timeout(&rngc->rng_op_done, RNGC_TIMEOUT);
+	ret = wait_for_completion_timeout(&rngc->rng_op_done, msecs_to_jiffies(RNGC_TIMEOUT));
 	imx_rngc_irq_mask_clear(rngc);
 	if (!ret)
 		return -ETIMEDOUT;
@@ -187,9 +187,7 @@ static int imx_rngc_init(struct hwrng *rng)
 		cmd = readl(rngc->base + RNGC_COMMAND);
 		writel(cmd | RNGC_CMD_SEED, rngc->base + RNGC_COMMAND);

-		ret = wait_for_completion_timeout(&rngc->rng_op_done,
-				RNGC_TIMEOUT);
-
+		ret = wait_for_completion_timeout(&rngc->rng_op_done, msecs_to_jiffies(RNGC_TIMEOUT));
 		if (!ret) {
 			ret = -ETIMEDOUT;
 			goto err;
--- a/drivers/char/hw_random/st-rng.c
+++ b/drivers/char/hw_random/st-rng.c
@@ -42,7 +42,6 @@

 struct st_rng_data {
 	void __iomem	*base;
-	struct clk	*clk;
 	struct hwrng	ops;
 };

@@ -85,26 +84,18 @@ static int st_rng_probe(struct platform_device *pdev)
 	if (IS_ERR(base))
 		return PTR_ERR(base);

-	clk = devm_clk_get(&pdev->dev, NULL);
+	clk = devm_clk_get_enabled(&pdev->dev, NULL);
 	if (IS_ERR(clk))
 		return PTR_ERR(clk);

-	ret = clk_prepare_enable(clk);
-	if (ret)
-		return ret;
-
 	ddata->ops.priv	= (unsigned long)ddata;
 	ddata->ops.read	= st_rng_read;
 	ddata->ops.name	= pdev->name;
 	ddata->base	= base;
-	ddata->clk	= clk;
-
-	dev_set_drvdata(&pdev->dev, ddata);

 	ret = devm_hwrng_register(&pdev->dev, &ddata->ops);
 	if (ret) {
 		dev_err(&pdev->dev, "Failed to register HW RNG\n");
-		clk_disable_unprepare(clk);
 		return ret;
 	}

@@ -113,15 +104,6 @@ static int st_rng_probe(struct platform_device *pdev)
 	return 0;
 }

-static int st_rng_remove(struct platform_device *pdev)
-{
-	struct st_rng_data *ddata = dev_get_drvdata(&pdev->dev);
-
-	clk_disable_unprepare(ddata->clk);
-
-	return 0;
-}
-
 static const struct of_device_id st_rng_match[] __maybe_unused = {
 	{ .compatible = "st,rng" },
 	{},
@@ -134,7 +116,6 @@ static struct platform_driver st_rng_driver = {
 		.of_match_table = of_match_ptr(st_rng_match),
 	},
 	.probe = st_rng_probe,
-	.remove = st_rng_remove
 };

 module_platform_driver(st_rng_driver);
--- a/drivers/char/hw_random/virtio-rng.c
+++ b/drivers/char/hw_random/virtio-rng.c
@@ -4,6 +4,7 @@
 *  Copyright (C) 2007, 2008 Rusty Russell IBM Corporation
 */

+#include <asm/barrier.h>
 #include <linux/err.h>
 #include <linux/hw_random.h>
 #include <linux/scatterlist.h>
@@ -20,12 +21,12 @@ struct virtrng_info {
 	struct virtqueue *vq;
 	char name[25];
 	int index;
-	bool busy;
 	bool hwrng_register_done;
 	bool hwrng_removed;
 	/* data transfer */
 	struct completion have_data;
 	unsigned int data_avail;
+	unsigned int data_idx;
 	/* minimal size returned by rng_buffer_size() */
 #if SMP_CACHE_BYTES < 32
 	u8 data[32];
@@ -37,19 +38,23 @@ struct virtrng_info {
 static void random_recv_done(struct virtqueue *vq)
 {
 	struct virtrng_info *vi = vq->vdev->priv;
+	unsigned int len;

 	/* We can get spurious callbacks, e.g. shared IRQs + virtio_pci. */
-	if (!virtqueue_get_buf(vi->vq, &vi->data_avail))
+	if (!virtqueue_get_buf(vi->vq, &len))
 		return;

+	smp_store_release(&vi->data_avail, len);
 	complete(&vi->have_data);
 }

-/* The host will fill any buffer we give it with sweet, sweet randomness. */
-static void register_buffer(struct virtrng_info *vi)
+static void request_entropy(struct virtrng_info *vi)
 {
 	struct scatterlist sg;

+	reinit_completion(&vi->have_data);
+	vi->data_idx = 0;
+
 	sg_init_one(&sg, vi->data, sizeof(vi->data));

 	/* There should always be room for one buffer. */
@@ -58,6 +63,18 @@ static void register_buffer(struct virtrng_info *vi)
 	virtqueue_kick(vi->vq);
 }

+static unsigned int copy_data(struct virtrng_info *vi, void *buf,
+			      unsigned int size)
+{
+	size = min_t(unsigned int, size, vi->data_avail);
+	memcpy(buf, vi->data + vi->data_idx, size);
+	vi->data_idx += size;
+	vi->data_avail -= size;
+	if (vi->data_avail == 0)
+		request_entropy(vi);
+	return size;
+}
+
 static int virtio_read(struct hwrng *rng, void *buf, size_t size, bool wait)
 {
 	int ret;
@@ -68,35 +85,37 @@ static int virtio_read(struct hwrng *rng, void *buf, size_t size, bool wait)
 	if (vi->hwrng_removed)
 		return -ENODEV;

-	if (!vi->busy) {
-		vi->busy = true;
-		reinit_completion(&vi->have_data);
-		register_buffer(vi);
+	read = 0;
+
+	/* copy available data */
+	if (smp_load_acquire(&vi->data_avail)) {
+		chunk = copy_data(vi, buf, size);
+		size -= chunk;
+		read += chunk;
 	}

 	if (!wait)
-		return 0;
+		return read;

-	read = 0;
+	/* We have already copied available entropy,
+	 * so either size is 0 or data_avail is 0
+	 */
 	while (size != 0) {
+		/* data_avail is 0 but a request is pending */
 		ret = wait_for_completion_killable(&vi->have_data);
 		if (ret < 0)
 			return ret;
+		/* if vi->data_avail is 0, we have been interrupted
+		 * by a cleanup, but buffer stays in the queue
+		 */
+		if (vi->data_avail == 0)
+			return read;

-		chunk = min_t(unsigned int, size, vi->data_avail);
-		memcpy(buf + read, vi->data, chunk);
-		read += chunk;
+		chunk = copy_data(vi, buf + read, size);
 		size -= chunk;
-		vi->data_avail = 0;
-
-		if (size != 0) {
-			reinit_completion(&vi->have_data);
-			register_buffer(vi);
-		}
+		read += chunk;
 	}

-	vi->busy = false;
-
 	return read;
 }

@@ -104,8 +123,7 @@ static void virtio_cleanup(struct hwrng *rng)
 {
 	struct virtrng_info *vi = (struct virtrng_info *)rng->priv;

-	if (vi->busy)
-		wait_for_completion(&vi->have_data);
+	complete(&vi->have_data);
 }

 static int probe_common(struct virtio_device *vdev)
@@ -141,6 +159,9 @@ static int probe_common(struct virtio_device *vdev)
 		goto err_find;
 	}

+	/* we always have a pending entropy request */
+	request_entropy(vi);
+
 	return 0;

 err_find:
@@ -156,9 +177,9 @@ static void remove_common(struct virtio_device *vdev)

 	vi->hwrng_removed = true;
 	vi->data_avail = 0;
+	vi->data_idx = 0;
 	complete(&vi->have_data);
 	vdev->config->reset(vdev);
-	vi->busy = false;
 	if (vi->hwrng_register_done)
 		hwrng_unregister(&vi->hwrng);
 	vdev->config->del_vqs(vdev);
--- a/drivers/char/tpm/tpm_vtpm_proxy.c
+++ b/drivers/char/tpm/tpm_vtpm_proxy.c
@@ -683,37 +683,21 @@ static struct miscdevice vtpmx_miscdev = {
 	.fops = &vtpmx_fops,
 };

-static int vtpmx_init(void)
-{
-	return misc_register(&vtpmx_miscdev);
-}
-
-static void vtpmx_cleanup(void)
-{
-	misc_deregister(&vtpmx_miscdev);
-}
-
 static int __init vtpm_module_init(void)
 {
 	int rc;

-	rc = vtpmx_init();
-	if (rc) {
-		pr_err("couldn't create vtpmx device\n");
-		return rc;
-	}
-
 	workqueue = create_workqueue("tpm-vtpm");
 	if (!workqueue) {
 		pr_err("couldn't create workqueue\n");
-		rc = -ENOMEM;
-		goto err_vtpmx_cleanup;
+		return -ENOMEM;
 	}

-	return 0;
-
-err_vtpmx_cleanup:
-	vtpmx_cleanup();
+	rc = misc_register(&vtpmx_miscdev);
+	if (rc) {
+		pr_err("couldn't create vtpmx device\n");
+		destroy_workqueue(workqueue);
+	}

 	return rc;
 }
@@ -721,7 +705,7 @@ err_vtpmx_cleanup:
 static void __exit vtpm_module_exit(void)
 {
 	destroy_workqueue(workqueue);
-	vtpmx_cleanup();
+	misc_deregister(&vtpmx_miscdev);
 }

 module_init(vtpm_module_init);
--- a/drivers/clk/clk-cdce925.c
+++ b/drivers/clk/clk-cdce925.c
@@ -705,6 +705,10 @@ static int cdce925_probe(struct i2c_client *client,
 	for (i = 0; i < data->chip_info->num_plls; ++i) {
 		pll_clk_name[i] = kasprintf(GFP_KERNEL, "%pOFn.pll%d",
 			client->dev.of_node, i);
+		if (!pll_clk_name[i]) {
+			err = -ENOMEM;
+			goto error;
+		}
 		init.name = pll_clk_name[i];
 		data->pll[i].chip = data;
 		data->pll[i].hw.init = &init;
@@ -746,6 +750,10 @@ static int cdce925_probe(struct i2c_client *client,
 	init.num_parents = 1;
 	init.parent_names = &parent_name; /* Mux Y1 to input */
 	init.name = kasprintf(GFP_KERNEL, "%pOFn.Y1", client->dev.of_node);
+	if (!init.name) {
+		err = -ENOMEM;
+		goto error;
+	}
 	data->clk[0].chip = data;
 	data->clk[0].hw.init = &init;
 	data->clk[0].index = 0;
@@ -764,6 +772,10 @@ static int cdce925_probe(struct i2c_client *client,
 	for (i = 1; i < data->chip_info->num_outputs; ++i) {
 		init.name = kasprintf(GFP_KERNEL, "%pOFn.Y%d",
 			client->dev.of_node, i+1);
+		if (!init.name) {
+			err = -ENOMEM;
+			goto error;
+		}
 		data->clk[i].chip = data;
 		data->clk[i].hw.init = &init;
 		data->clk[i].index = i;
--- a/drivers/clk/clk-si5341.c
+++ b/drivers/clk/clk-si5341.c
@@ -1554,7 +1554,7 @@ static int si5341_probe(struct i2c_client *client,
 	struct clk_init_data init;
 	struct clk *input;
 	const char *root_clock_name;
-	const char *synth_clock_names[SI5341_NUM_SYNTH];
+	const char *synth_clock_names[SI5341_NUM_SYNTH] = { NULL };
 	int err;
 	unsigned int i;
 	struct clk_si5341_output_config config[SI5341_MAX_NUM_OUTPUTS];
@@ -1698,6 +1698,10 @@ static int si5341_probe(struct i2c_client *client,
 	for (i = 0; i < data->num_synth; ++i) {
 		synth_clock_names[i] = devm_kasprintf(&client->dev, GFP_KERNEL,
 				"%s.N%u", client->dev.of_node->name, i);
+		if (!synth_clock_names[i]) {
+			err = -ENOMEM;
+			goto free_clk_names;
+		}
 		init.name = synth_clock_names[i];
 		data->synth[i].index = i;
 		data->synth[i].data = data;
@@ -1706,6 +1710,7 @@ static int si5341_probe(struct i2c_client *client,
 		if (err) {
 			dev_err(&client->dev,
 				"synth N%u registration failed\n", i);
+			goto free_clk_names;
 		}
 	}

@@ -1715,6 +1720,10 @@ static int si5341_probe(struct i2c_client *client,
 	for (i = 0; i < data->num_outputs; ++i) {
 		init.name = kasprintf(GFP_KERNEL, "%s.%d",
 			client->dev.of_node->name, i);
+		if (!init.name) {
+			err = -ENOMEM;
+			goto free_clk_names;
+		}
 		init.flags = config[i].synth_master ? CLK_SET_RATE_PARENT : 0;
 		data->clk[i].index = i;
 		data->clk[i].data = data;
@@ -1736,7 +1745,7 @@ static int si5341_probe(struct i2c_client *client,
 		if (err) {
 			dev_err(&client->dev,
 				"output %u registration failed\n", i);
-			goto cleanup;
+			goto free_clk_names;
 		}
 		if (config[i].always_on)
 			clk_prepare(data->clk[i].hw.clk);
@@ -1746,7 +1755,7 @@ static int si5341_probe(struct i2c_client *client,
 			data);
 	if (err) {
 		dev_err(&client->dev, "unable to add clk provider\n");
-		goto cleanup;
+		goto free_clk_names;
 	}

 	if (initialization_required) {
@@ -1754,11 +1763,11 @@ static int si5341_probe(struct i2c_client *client,
 		regcache_cache_only(data->regmap, false);
 		err = regcache_sync(data->regmap);
 		if (err < 0)
-			goto cleanup;
+			goto free_clk_names;

 		err = si5341_finalize_defaults(data);
 		if (err < 0)
-			goto cleanup;
+			goto free_clk_names;
 	}

 	/* wait for device to report input clock present and PLL lock */
@@ -1767,32 +1776,31 @@ static int si5341_probe(struct i2c_client *client,
 	       10000, 250000);
 	if (err) {
 		dev_err(&client->dev, "Error waiting for input clock or PLL lock\n");
-		goto cleanup;
+		goto free_clk_names;
 	}

 	/* clear sticky alarm bits from initialization */
 	err = regmap_write(data->regmap, SI5341_STATUS_STICKY, 0);
 	if (err) {
 		dev_err(&client->dev, "unable to clear sticky status\n");
-		goto cleanup;
+		goto free_clk_names;
 	}

 	err = sysfs_create_files(&client->dev.kobj, si5341_attributes);
-	if (err) {
+	if (err)
 		dev_err(&client->dev, "unable to create sysfs files\n");
-		goto cleanup;
-	}

+free_clk_names:
 	/* Free the names, clk framework makes copies */
 	for (i = 0; i < data->num_synth; ++i)
 		 devm_kfree(&client->dev, (void *)synth_clock_names[i]);

-	return 0;
-
 cleanup:
-	for (i = 0; i < SI5341_MAX_NUM_OUTPUTS; ++i) {
-		if (data->clk[i].vddo_reg)
-			regulator_disable(data->clk[i].vddo_reg);
+	if (err) {
+		for (i = 0; i < SI5341_MAX_NUM_OUTPUTS; ++i) {
+			if (data->clk[i].vddo_reg)
+				regulator_disable(data->clk[i].vddo_reg);
+		}
 	}
 	return err;
 }
--- a/drivers/clk/clk-versaclock5.c
+++ b/drivers/clk/clk-versaclock5.c
@@ -992,6 +992,11 @@ static int vc5_probe(struct i2c_client *client, const struct i2c_device_id *id)
 	}

 	init.name = kasprintf(GFP_KERNEL, "%pOFn.mux", client->dev.of_node);
+	if (!init.name) {
+		ret = -ENOMEM;
+		goto err_clk;
+	}
+
 	init.ops = &vc5_mux_ops;
 	init.flags = 0;
 	init.parent_names = parent_names;
@@ -1006,6 +1011,10 @@ static int vc5_probe(struct i2c_client *client, const struct i2c_device_id *id)
 		memset(&init, 0, sizeof(init));
 		init.name = kasprintf(GFP_KERNEL, "%pOFn.dbl",
 				      client->dev.of_node);
+		if (!init.name) {
+			ret = -ENOMEM;
+			goto err_clk;
+		}
 		init.ops = &vc5_dbl_ops;
 		init.flags = CLK_SET_RATE_PARENT;
 		init.parent_names = parent_names;
@@ -1021,6 +1030,10 @@ static int vc5_probe(struct i2c_client *client, const struct i2c_device_id *id)
 	/* Register PFD */
 	memset(&init, 0, sizeof(init));
 	init.name = kasprintf(GFP_KERNEL, "%pOFn.pfd", client->dev.of_node);
+	if (!init.name) {
+		ret = -ENOMEM;
+		goto err_clk;
+	}
 	init.ops = &vc5_pfd_ops;
 	init.flags = CLK_SET_RATE_PARENT;
 	init.parent_names = parent_names;
@@ -1038,6 +1051,10 @@ static int vc5_probe(struct i2c_client *client, const struct i2c_device_id *id)
 	/* Register PLL */
 	memset(&init, 0, sizeof(init));
 	init.name = kasprintf(GFP_KERNEL, "%pOFn.pll", client->dev.of_node);
+	if (!init.name) {
+		ret = -ENOMEM;
+		goto err_clk;
+	}
 	init.ops = &vc5_pll_ops;
 	init.flags = CLK_SET_RATE_PARENT;
 	init.parent_names = parent_names;
@@ -1057,6 +1074,10 @@ static int vc5_probe(struct i2c_client *client, const struct i2c_device_id *id)
 		memset(&init, 0, sizeof(init));
 		init.name = kasprintf(GFP_KERNEL, "%pOFn.fod%d",
 				      client->dev.of_node, idx);
+		if (!init.name) {
+			ret = -ENOMEM;
+			goto err_clk;
+		}
 		init.ops = &vc5_fod_ops;
 		init.flags = CLK_SET_RATE_PARENT;
 		init.parent_names = parent_names;
@@ -1075,6 +1096,10 @@ static int vc5_probe(struct i2c_client *client, const struct i2c_device_id *id)
 	memset(&init, 0, sizeof(init));
 	init.name = kasprintf(GFP_KERNEL, "%pOFn.out0_sel_i2cb",
 			      client->dev.of_node);
+	if (!init.name) {
+		ret = -ENOMEM;
+		goto err_clk;
+	}
 	init.ops = &vc5_clk_out_ops;
 	init.flags = CLK_SET_RATE_PARENT;
 	init.parent_names = parent_names;
@@ -1101,6 +1126,10 @@ static int vc5_probe(struct i2c_client *client, const struct i2c_device_id *id)
 		memset(&init, 0, sizeof(init));
 		init.name = kasprintf(GFP_KERNEL, "%pOFn.out%d",
 				      client->dev.of_node, idx + 1);
+		if (!init.name) {
+			ret = -ENOMEM;
+			goto err_clk;
+		}
 		init.ops = &vc5_clk_out_ops;
 		init.flags = CLK_SET_RATE_PARENT;
 		init.parent_names = parent_names;
--- a/drivers/clk/clk.c
+++ b/drivers/clk/clk.c
@@ -4569,6 +4569,7 @@ int devm_clk_notifier_register(struct device *dev, struct clk *clk,
 	if (!ret) {
 		devres->clk = clk;
 		devres->nb = nb;
+		devres_add(dev, devres);
 	} else {
 		devres_free(devres);
 	}
--- a/drivers/clk/imx/clk-imx8mn.c
+++ b/drivers/clk/imx/clk-imx8mn.c
@@ -299,7 +299,7 @@ static int imx8mn_clocks_probe(struct platform_device *pdev)
 	void __iomem *base;
 	int ret;

-	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws,
+	clk_hw_data = devm_kzalloc(dev, struct_size(clk_hw_data, hws,
 					  IMX8MN_CLK_END), GFP_KERNEL);
 	if (WARN_ON(!clk_hw_data))
 		return -ENOMEM;
@@ -316,10 +316,10 @@ static int imx8mn_clocks_probe(struct platform_device *pdev)
 	hws[IMX8MN_CLK_EXT4] = imx_obtain_fixed_clk_hw(np, "clk_ext4");

 	np = of_find_compatible_node(NULL, NULL, "fsl,imx8mn-anatop");
-	base = of_iomap(np, 0);
+	base = devm_of_iomap(dev, np, 0, NULL);
 	of_node_put(np);
-	if (WARN_ON(!base)) {
-		ret = -ENOMEM;
+	if (WARN_ON(IS_ERR(base))) {
+		ret = PTR_ERR(base);
 		goto unregister_hws;
 	}

--- a/drivers/clk/imx/clk-imx8mp.c
+++ b/drivers/clk/imx/clk-imx8mp.c
@@ -407,25 +407,22 @@ static int imx8mp_clocks_probe(struct platform_device *pdev)
 	struct device *dev = &pdev->dev;
 	struct device_node *np;
 	void __iomem *anatop_base, *ccm_base;
+	int err;

 	np = of_find_compatible_node(NULL, NULL, "fsl,imx8mp-anatop");
-	anatop_base = of_iomap(np, 0);
+	anatop_base = devm_of_iomap(dev, np, 0, NULL);
 	of_node_put(np);
-	if (WARN_ON(!anatop_base))
-		return -ENOMEM;
+	if (WARN_ON(IS_ERR(anatop_base)))
+		return PTR_ERR(anatop_base);

 	np = dev->of_node;
 	ccm_base = devm_platform_ioremap_resource(pdev, 0);
-	if (WARN_ON(IS_ERR(ccm_base))) {
-		iounmap(anatop_base);
+	if (WARN_ON(IS_ERR(ccm_base)))
 		return PTR_ERR(ccm_base);
-	}

-	clk_hw_data = kzalloc(struct_size(clk_hw_data, hws, IMX8MP_CLK_END), GFP_KERNEL);
-	if (WARN_ON(!clk_hw_data)) {
-		iounmap(anatop_base);
+	clk_hw_data = devm_kzalloc(dev, struct_size(clk_hw_data, hws, IMX8MP_CLK_END), GFP_KERNEL);
+	if (WARN_ON(!clk_hw_data))
 		return -ENOMEM;
-	}

 	clk_hw_data->num = IMX8MP_CLK_END;
 	hws = clk_hw_data->hws;
@@ -710,7 +707,12 @@ static int imx8mp_clocks_probe(struct platform_device *pdev)

 	imx_check_clk_hws(hws, IMX8MP_CLK_END);

-	of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_hw_data);
+	err = of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_hw_data);
+	if (err < 0) {
+		dev_err(dev, "failed to register hws for i.MX8MP\n");
+		imx_unregister_hw_clocks(hws, IMX8MP_CLK_END);
+		return err;
+	}

 	imx_register_uart_clocks(4);

--- a/drivers/clk/imx/clk-scu.c
+++ b/drivers/clk/imx/clk-scu.c
@@ -702,11 +702,11 @@ struct clk_hw *imx_clk_scu_alloc_dev(const char *name,

 void imx_clk_scu_unregister(void)
 {
-	struct imx_scu_clk_node *clk;
+	struct imx_scu_clk_node *clk, *n;
 	int i;

 	for (i = 0; i < IMX_SC_R_LAST; i++) {
-		list_for_each_entry(clk, &imx_scu_clks[i], node) {
+		list_for_each_entry_safe(clk, n, &imx_scu_clks[i], node) {
 			clk_hw_unregister(clk->hw);
 			kfree(clk);
 		}
--- a/drivers/clk/keystone/sci-clk.c
+++ b/drivers/clk/keystone/sci-clk.c
@@ -302,6 +302,8 @@ static int _sci_clk_build(struct sci_clk_provider *provider,

 	name = kasprintf(GFP_KERNEL, "clk:%d:%d", sci_clk->dev_id,
 			 sci_clk->clk_id);
+	if (!name)
+		return -ENOMEM;

 	init.name = name;

--- a/drivers/clk/qcom/camcc-sc7180.c
+++ b/drivers/clk/qcom/camcc-sc7180.c
@@ -1493,12 +1493,21 @@ static struct clk_branch cam_cc_sys_tmr_clk = {
 	},
 };

+static struct gdsc titan_top_gdsc = {
+	.gdscr = 0xb134,
+	.pd = {
+		.name = "titan_top_gdsc",
+	},
+	.pwrsts = PWRSTS_OFF_ON,
+};
+
 static struct gdsc bps_gdsc = {
 	.gdscr = 0x6004,
 	.pd = {
 		.name = "bps_gdsc",
 	},
 	.pwrsts = PWRSTS_OFF_ON,
+	.parent = &titan_top_gdsc.pd,
 	.flags = HW_CTRL,
 };

@@ -1508,6 +1517,7 @@ static struct gdsc ife_0_gdsc = {
 		.name = "ife_0_gdsc",
 	},
 	.pwrsts = PWRSTS_OFF_ON,
+	.parent = &titan_top_gdsc.pd,
 };

 static struct gdsc ife_1_gdsc = {
@@ -1516,6 +1526,7 @@ static struct gdsc ife_1_gdsc = {
 		.name = "ife_1_gdsc",
 	},
 	.pwrsts = PWRSTS_OFF_ON,
+	.parent = &titan_top_gdsc.pd,
 };

 static struct gdsc ipe_0_gdsc = {
@@ -1525,15 +1536,9 @@ static struct gdsc ipe_0_gdsc = {
 	},
 	.pwrsts = PWRSTS_OFF_ON,
 	.flags = HW_CTRL,
+	.parent = &titan_top_gdsc.pd,
 };

-static struct gdsc titan_top_gdsc = {
-	.gdscr = 0xb134,
-	.pd = {
-		.name = "titan_top_gdsc",
-	},
-	.pwrsts = PWRSTS_OFF_ON,
-};

 static struct clk_hw *cam_cc_sc7180_hws[] = {
 	[CAM_CC_PLL2_OUT_EARLY] = &cam_cc_pll2_out_early.hw,
--- a/drivers/clk/qcom/gcc-ipq6018.c
+++ b/drivers/clk/qcom/gcc-ipq6018.c
@@ -1654,7 +1654,7 @@ static struct clk_rcg2 sdcc1_apps_clk_src = {
 		.name = "sdcc1_apps_clk_src",
 		.parent_data = gcc_xo_gpll0_gpll2_gpll0_out_main_div2,
 		.num_parents = 4,
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_floor_ops,
 	},
 };

@@ -4517,24 +4517,24 @@ static const struct qcom_reset_map gcc_ipq6018_resets[] = {
 	[GCC_PCIE0_AHB_ARES] = { 0x75040, 5 },
 	[GCC_PCIE0_AXI_MASTER_STICKY_ARES] = { 0x75040, 6 },
 	[GCC_PCIE0_AXI_SLAVE_STICKY_ARES] = { 0x75040, 7 },
-	[GCC_PPE_FULL_RESET] = { 0x68014, 0 },
-	[GCC_UNIPHY0_SOFT_RESET] = { 0x56004, 0 },
+	[GCC_PPE_FULL_RESET] = { .reg = 0x68014, .bitmask = 0xf0000 },
+	[GCC_UNIPHY0_SOFT_RESET] = { .reg = 0x56004, .bitmask = 0x3ff2 },
 	[GCC_UNIPHY0_XPCS_RESET] = { 0x56004, 2 },
-	[GCC_UNIPHY1_SOFT_RESET] = { 0x56104, 0 },
+	[GCC_UNIPHY1_SOFT_RESET] = { .reg = 0x56104, .bitmask = 0x32 },
 	[GCC_UNIPHY1_XPCS_RESET] = { 0x56104, 2 },
-	[GCC_EDMA_HW_RESET] = { 0x68014, 0 },
-	[GCC_NSSPORT1_RESET] = { 0x68014, 0 },
-	[GCC_NSSPORT2_RESET] = { 0x68014, 0 },
-	[GCC_NSSPORT3_RESET] = { 0x68014, 0 },
-	[GCC_NSSPORT4_RESET] = { 0x68014, 0 },
-	[GCC_NSSPORT5_RESET] = { 0x68014, 0 },
-	[GCC_UNIPHY0_PORT1_ARES] = { 0x56004, 0 },
-	[GCC_UNIPHY0_PORT2_ARES] = { 0x56004, 0 },
-	[GCC_UNIPHY0_PORT3_ARES] = { 0x56004, 0 },
-	[GCC_UNIPHY0_PORT4_ARES] = { 0x56004, 0 },
-	[GCC_UNIPHY0_PORT5_ARES] = { 0x56004, 0 },
-	[GCC_UNIPHY0_PORT_4_5_RESET] = { 0x56004, 0 },
-	[GCC_UNIPHY0_PORT_4_RESET] = { 0x56004, 0 },
+	[GCC_EDMA_HW_RESET] = { .reg = 0x68014, .bitmask = 0x300000 },
+	[GCC_NSSPORT1_RESET] = { .reg = 0x68014, .bitmask = 0x1000003 },
+	[GCC_NSSPORT2_RESET] = { .reg = 0x68014, .bitmask = 0x200000c },
+	[GCC_NSSPORT3_RESET] = { .reg = 0x68014, .bitmask = 0x4000030 },
+	[GCC_NSSPORT4_RESET] = { .reg = 0x68014, .bitmask = 0x8000300 },
+	[GCC_NSSPORT5_RESET] = { .reg = 0x68014, .bitmask = 0x10000c00 },
+	[GCC_UNIPHY0_PORT1_ARES] = { .reg = 0x56004, .bitmask = 0x30 },
+	[GCC_UNIPHY0_PORT2_ARES] = { .reg = 0x56004, .bitmask = 0xc0 },
+	[GCC_UNIPHY0_PORT3_ARES] = { .reg = 0x56004, .bitmask = 0x300 },
+	[GCC_UNIPHY0_PORT4_ARES] = { .reg = 0x56004, .bitmask = 0xc00 },
+	[GCC_UNIPHY0_PORT5_ARES] = { .reg = 0x56004, .bitmask = 0x3000 },
+	[GCC_UNIPHY0_PORT_4_5_RESET] = { .reg = 0x56004, .bitmask = 0x3c02 },
+	[GCC_UNIPHY0_PORT_4_RESET] = { .reg = 0x56004, .bitmask = 0xc02 },
 	[GCC_LPASS_BCR] = {0x1F000, 0},
 	[GCC_UBI32_TBU_BCR] = {0x65000, 0},
 	[GCC_LPASS_TBU_BCR] = {0x6C000, 0},
--- a/drivers/clk/qcom/reset.c
+++ b/drivers/clk/qcom/reset.c
@@ -13,8 +13,10 @@

 static int qcom_reset(struct reset_controller_dev *rcdev, unsigned long id)
 {
+	struct qcom_reset_controller *rst = to_qcom_reset_controller(rcdev);
+
 	rcdev->ops->assert(rcdev, id);
-	udelay(1);
+	udelay(rst->reset_map[id].udelay ?: 1); /* use 1 us as default */
 	rcdev->ops->deassert(rcdev, id);
 	return 0;
 }
@@ -28,7 +30,7 @@ qcom_reset_assert(struct reset_controller_dev *rcdev, unsigned long id)

 	rst = to_qcom_reset_controller(rcdev);
 	map = &rst->reset_map[id];
-	mask = BIT(map->bit);
+	mask = map->bitmask ? map->bitmask : BIT(map->bit);

 	return regmap_update_bits(rst->regmap, map->reg, mask, mask);
 }
@@ -42,7 +44,7 @@ qcom_reset_deassert(struct reset_controller_dev *rcdev, unsigned long id)

 	rst = to_qcom_reset_controller(rcdev);
 	map = &rst->reset_map[id];
-	mask = BIT(map->bit);
+	mask = map->bitmask ? map->bitmask : BIT(map->bit);

 	return regmap_update_bits(rst->regmap, map->reg, mask, 0);
 }
--- a/drivers/clk/qcom/reset.h
+++ b/drivers/clk/qcom/reset.h
@@ -11,6 +11,8 @@
 struct qcom_reset_map {
 	unsigned int reg;
 	u8 bit;
+	u8 udelay;
+	u32 bitmask;
 };

 struct regmap;
--- a/drivers/clk/tegra/clk-tegra124-emc.c
+++ b/drivers/clk/tegra/clk-tegra124-emc.c
@@ -464,6 +464,7 @@ static int load_timings_from_dt(struct tegra_clk_emc *tegra,
 		err = load_one_timing_from_dt(tegra, timing, child);
 		if (err) {
 			of_node_put(child);
+			kfree(tegra->timings);
 			return err;
 		}

@@ -515,6 +516,7 @@ struct clk *tegra124_clk_register_emc(void __iomem *base, struct device_node *np
 		err = load_timings_from_dt(tegra, node, node_ram_code);
 		if (err) {
 			of_node_put(node);
+			kfree(tegra);
 			return ERR_PTR(err);
 		}
 	}
--- a/drivers/clk/ti/clkctrl.c
+++ b/drivers/clk/ti/clkctrl.c
@@ -267,6 +267,9 @@ static const char * __init clkctrl_get_clock_name(struct device_node *np,
 	if (clkctrl_name && !legacy_naming) {
 		clock_name = kasprintf(GFP_KERNEL, "%s-clkctrl:%04x:%d",
 				       clkctrl_name, offset, index);
+		if (!clock_name)
+			return NULL;
+
 		strreplace(clock_name, '_', '-');

 		return clock_name;
@@ -598,6 +601,10 @@ static void __init _ti_omap4_clkctrl_setup(struct device_node *node)
 	if (clkctrl_name) {
 		provider->clkdm_name = kasprintf(GFP_KERNEL,
 						 "%s_clkdm", clkctrl_name);
+		if (!provider->clkdm_name) {
+			kfree(provider);
+			return;
+		}
 		goto clkdm_found;
 	}

--- a/drivers/crypto/marvell/cesa/cipher.c
+++ b/drivers/crypto/marvell/cesa/cipher.c
@@ -297,7 +297,7 @@ static int mv_cesa_des_setkey(struct crypto_skcipher *cipher, const u8 *key,
 static int mv_cesa_des3_ede_setkey(struct crypto_skcipher *cipher,
 				   const u8 *key, unsigned int len)
 {
-	struct mv_cesa_des_ctx *ctx = crypto_skcipher_ctx(cipher);
+	struct mv_cesa_des3_ctx *ctx = crypto_skcipher_ctx(cipher);
 	int err;

 	err = verify_skcipher_des3_key(cipher, key);
--- a/Show More
+++ b/Show More