Because v4 and v6 families use separate inetpeer trees (respectively
net->ipv4.peers and net->ipv6.peers), inetpeer_addr_cmp(a, b) assumes
a & b share the same family.
tcp_metrics use a common hash table, where entries can have different
families.
We must therefore make sure to not call inetpeer_addr_cmp()
if the families do not match.
Fixes: d39d14ffa2 ("net: Add helper function to compare inetpeer addresses")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230802131500.1478140-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When both supported and previous version have the same major version,
and the firmwares are missing, the driver ends in a loop requesting the
same (previous) version over and over again:
[ 76.327413] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.1.img firmware, fall-back to previous 4.0 version
[ 76.339802] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.352162] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.364502] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.376848] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.389183] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.401522] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.413860] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.426199] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
...
Fix this by inverting the check to that we aren't yet at the previous
version, and also check the minor version.
This also catches the case where both versions are the same, as it was
after commit bb5dbf2cc6 ("net: marvell: prestera: add firmware v4.0
support").
With this fix applied:
[ 88.499622] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.1.img firmware, fall-back to previous 4.0 version
[ 88.511995] Prestera DX 0000:01:00.0: failed to request previous firmware: mrvl/prestera/mvsw_prestera_fw-v4.0.img
[ 88.522403] Prestera DX: probe of 0000:01:00.0 failed with error -2
Fixes: 47f26018a4 ("net: marvell: prestera: try to load previous fw version")
Signed-off-by: Jonas Gorski <jonas.gorski@bisdn.de>
Acked-by: Elad Nachman <enachman@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Taras Chornyi <taras.chornyi@plvision.eu>
Link: https://lore.kernel.org/r/20230802092357.163944-1-jonas.gorski@bisdn.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski says:
====================
docs: net: page_pool: sync dev and kdoc
Document PP_FLAG_DMA_SYNC_DEV based on recent conversation.
Use kdoc to document structs and functions, to avoid duplication.
Olek, this will conflict with your work, but I think that trying
to make progress in parallel is the best course of action...
Retargetting at net-next to make it a little less bad.
====================
Link: https://lore.kernel.org/r/20230802161821.3621985-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All struct members of the driver-facing APIs are documented twice,
in the code and under Documentation. This is a bit tedious.
I also get the feeling that a lot of developers will read the header
when coding, rather than the doc. Bring the two a little closer
together by using kdoc for structs and functions.
Using kdoc also gives us links (mentioning a function or struct
in the text gets replaced by a link to its doc).
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20230802161821.3621985-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull nfsd fix from Chuck Lever:
- Fix tmpfs splice read support
* tag 'nfsd-6.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
nfsd: Fix reading via splice
Pull erofs fixes from Gao Xiang:
- Fix data corruption caused by insufficient decompression on
deduplicated compressed extents
- Drop a useless s_magic checking in erofs_kill_sb()
* tag 'erofs-for-6.5-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: drop unnecessary WARN_ON() in erofs_kill_sb()
erofs: fix wrong primary bvec selection on deduplicated extents
Pull s390 fixes from Heiko Carstens:
- Split kernel large page mappings into 4k mappings in case debug
pagealloc is enabled again. This got accidentally removed by commit
bb1520d581 ("s390/mm: start kernel with DAT enabled")
- Fix error handling in KVM's sthyi handling
- Add missing include to s390's uapi ptrace.h
- Update defconfigs
* tag 's390-6.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ptrace: add missing linux/const.h include
KVM: s390: fix sthyi error handling
s390: update defconfigs
s390/vmem: split pages when debug pagealloc is enabled
Jakub Kicinski says:
====================
While poking at struct netdev_rx_queue I got annoyed by
the huge rebuild times. I split it out from netdevice.h
and then realized that it was the main reason we included
xdp.h in there. So I removed that dependency as well.
This gives us very pleasant build times for both xdp.h
and struct netdev_rx_queue changes.
I'm sending this for bpf-next because I think it'd be easiest
if it goes in there, and then bpf-next gets flushed soon after?
I can also make a branch on merge-base for net-next and bpf-next..
v2:
- build fix
- reorder some includes
v1: https://lore.kernel.org/all/20230802003246.2153774-1-kuba@kernel.org/
====================
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
xdp.h is far more specific and is included in only 67 other
files vs netdevice.h's 1538 include sites.
Make xdp.h include netdevice.h, instead of the other way around.
This decreases the incremental allmodconfig builds size when
xdp.h is touched from 5947 to 662 objects.
Move bpf_prog_run_xdp() to xdp.h, seems appropriate and filter.h
is a mega-header in its own right so it's nice to avoid xdp.h
getting included there as well.
The only unfortunate part is that the typedef for xdp_features_t
has to move to netdevice.h, since its embedded in struct netdevice.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20230803010230.1755386-4-kuba@kernel.org
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
struct netdev_rx_queue is touched in only a few places
and having it defined in netdevice.h brings in the dependency
on xdp.h, because struct xdp_rxq_info gets embedded in
struct netdev_rx_queue.
In prep for removal of xdp.h from netdevice.h move all
the netdev_rx_queue stuff to a new header.
We could technically break the new header up to avoid
the sysfs.h include but it's so rarely included it
doesn't seem to be worth it at this point.
Reviewed-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20230803010230.1755386-3-kuba@kernel.org
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
When setting ZT0 via ptrace we do not currently force a reload of the
floating point register state from memory, do that to ensure that the newly
set value gets loaded into the registers on next task execution.
The function was templated off the function for FPSIMD which due to our
providing the option of embedding a FPSIMD regset within the SVE regset
does not directly include the flush.
Fixes: f90b529bcb ("arm64/sme: Implement ZT0 ptrace support")
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230803-arm64-fix-ptrace-zt0-flush-v1-1-72e854eaf96e@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When setting SME vector lengths we clear TIF_SME to reenable SME traps,
doing a reallocation of the backing storage on next use. We do this using
clear_thread_flag() which operates on the current thread, meaning that when
setting the vector length via ptrace we may both not force traps for the
target task and force a spurious flush of any SME state that the tracing
task may have.
Clear the flag in the target task.
Fixes: e12310a0d3 ("arm64/sme: Implement ptrace support for streaming mode SVE registers")
Reported-by: David Spickett <David.Spickett@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230803-arm64-fix-ptrace-tif-sme-v1-1-88312fd6fbfd@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Aaron Conole says:
====================
selftests: openvswitch: add flow programming cases
The openvswitch selftests currently contain a few cases for managing the
datapath, which includes creating datapath instances, adding interfaces,
and doing some basic feature / upcall tests. This is useful to validate
the control path.
Add the ability to program some of the more common flows with actions. This
can be improved overtime to include regression testing, etc.
====================
Link: https://lore.kernel.org/r/20230801212226.909249-1-aconole@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Building on the previous work, add a very simplistic NAT case
using ipv4. This just tests dnat transformation
Signed-off-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Forwarding via ct() action is an important use case for openvswitch, but
generally would require using a full ovs-vswitchd to get working. Add a
ct action parser for basic ct test case.
Signed-off-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Adrian Moreno <amorenoz@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The default value for the mask actually depends on the value (e.g: if
the value is non-null, the default is full-mask), so change the convert
functions to accept the full, possibly masked string and let them figure
out how to parse the different values.
Also, implement size-aware int parsing.
With this patch we can now express flows such as the following:
"eth(src=0a:ca:fe:ca:fe:0a/ff:ff:00:00:ff:00)"
"eth(src=0a:ca:fe:ca:fe:0a)" -> mask = ff:ff:ff:ff:ff:ff
"ipv4(src=192.168.1.1)" -> mask = 255.255.255.255
"ipv4(src=192.168.1.1/24)"
"ipv4(src=192.168.1.1/255.255.255.0)"
"tcp(src=8080)" -> mask = 0xffff
"tcp(src=8080/0xf0f0)"
Signed-off-by: Adrian Moreno <amorenoz@redhat.com>
Acked-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The openvswitch self-tests can test much of the control side of
the module (ie: what a vswitchd implementation would process),
but the actual packet forwarding cases aren't supported, making
the testing of limited value.
Add some flow parsing and an initial ARP based test case using
arping utility. This lets us display flows, add some basic
output flows with simple matches, and test against a known good
forwarding case.
Signed-off-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Adrian Moreno <amorenoz@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
__ip6_append_data() can has a similar problem to __ip_append_data()[1] when
asked to splice into a partially-built UDP message that has more than the
frag-limit data and up to the MTU limit, but in the ipv6 case, it errors
out with EINVAL. This can be triggered with something like:
pipe(pfd);
sfd = socket(AF_INET6, SOCK_DGRAM, 0);
connect(sfd, ...);
send(sfd, buffer, 8137, MSG_CONFIRM|MSG_MORE);
write(pfd[1], buffer, 8);
splice(pfd[0], 0, sfd, 0, 0x4ffe0ul, 0);
where the amount of data given to send() is dependent on the MTU size (in
this instance an interface with an MTU of 8192).
The problem is that the calculation of the amount to copy in
__ip6_append_data() goes negative in two places, but a check has been put
in to give an error in this case.
This happens because when pagedlen > 0 (which happens for MSG_ZEROCOPY and
MSG_SPLICE_PAGES), the terms in:
copy = datalen - transhdrlen - fraggap - pagedlen;
then mostly cancel when pagedlen is substituted for, leaving just -fraggap.
Fix this by:
(1) Insert a note about the dodgy calculation of 'copy'.
(2) If MSG_SPLICE_PAGES, clear copy if it is negative from the above
equation, so that 'offset' isn't regressed and 'length' isn't
increased, which will mean that length and thus copy should match the
amount left in the iterator.
(3) When handling MSG_SPLICE_PAGES, give a warning and return -EIO if
we're asked to splice more than is in the iterator. It might be
better to not give the warning or even just give a 'short' write.
(4) If MSG_SPLICE_PAGES, override the copy<0 check.
[!] Note that this should also affect MSG_ZEROCOPY, but that will return
-EINVAL for the range of send sizes that requires the skbuff to be split.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: David Ahern <dsahern@kernel.org>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
cc: netdev@vger.kernel.org
Link: https://lore.kernel.org/r/000000000000881d0606004541d1@google.com/ [1]
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/1580952.1690961810@warthog.procyon.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix checkpatch warnings:
unaligned.c:475: ERROR: space required after that ','
Signed-off-by: Yu Han <hanyu001@208suo.com>
Signed-off-by: Helge Deller <deller@gmx.de>
This driver does not actually work with DMA mode, but still tries
to call ISA DMA interface functions that are stubbed out on
parisc, resulting in a W=1 build warning:
drivers/parport/parport_gsc.c: In function 'parport_remove_chip':
drivers/parport/parport_gsc.c:389:20: warning: suggest braces around empty body in an 'if' statement [-Wempty-body]
389 | free_dma(p->dma);
Remove the corresponding code as a prerequisite for turning on -Wempty-body
by default in all kernels.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Clearly, this code isn't needed, but it gives a false positive when
grepping the complete source tree for coherent_dma_mask.
Signed-off-by: Petr Tesarik <petr.tesarik.ext@huawei.com>
Signed-off-by: Helge Deller <deller@gmx.de>
WiFi 7 chips doesn't have static const tables defined in driver. If tables
aren't loaded properly from firmware file, driver can get NULL pointer
access exception. One way is to add the checking statements when trying to
access these tables, but I choose to check them right after loading
firmware elements from firmware file, so I don't need to add error handlers
everywhere.
Currently, the needed firmware elements of WiFi 6 chips are all zero, and
coming WiFi 7 chip will need at least BB MCU, parameters of BB and RF.
We will add them after 8922AE is verified.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-9-pkshih@realtek.com
The tables of BB and RF parameters are pairs of {addr, value}. Load them
and convert from little-endian to CPU order, and show the version to clear
which version we are using.
rtw89_8922ae 0000:03:00.0: Firmware element BB version: 00 04 00 00
rtw89_8922ae 0000:03:00.0: Firmware element radio A version: 00 13 00 00
rtw89_8922ae 0000:03:00.0: Firmware element NCTL version: 00 05 00 00
We use tables defined in firmware elements with higher priority than
original static const tables defined in driver, because WiFi 7 chips will
not define the tables in driver, and existing chips can possibly migrate to
the new design one by one.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-8-pkshih@realtek.com
In order to pack more data into firmware file, we introduce firmware
elements and append BB_MCU firmware first. The first part of new firmware
file is still unchanged firmware of WiFi CPU, so the new firmware format
can be backward compatible to old format. The new elements part consists
of ID and size basically, which can append more elements simply. To avoid
unaligned access in certain platform and be easy to read, headers of all
elements start at 16-byte aligned address.
+===========================================+
| original firmware |
| +-------------+
| | padding |
+===========================================+
| elm ID 1 | elm size | other header data |
+----------+----------+ |
| |
+-------------------------------------------+
| content (variable length) |
| +-------------+
| | padding |
+===========================================+
| elm ID 2 | elm size | other header data |
+----------+----------+ |
| |
+-------------------------------------------+
| content (variable length) |
| +-----------------------+
| | (no padding for the last one)
+===================+
More detail of element header is shown below. The additional fields
'version' and 'element_priv[]' are meta data of elements, so that we can
know element version easily, and element_priv[] provide specific fields
for certain element, such as RF path index for RF parameter tables.
+===========================================+
| elm ID | elm size | version | rsvd0 |
+----------+----------+----------+----------+
| rsvd1/2 | element_priv[] |
+-------------------------------------------+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-7-pkshih@realtek.com
For existing chips, firmware is only for WiFi CPU, but WiFi 7 chips add
new hardware component BB MCU that needs firmware as well. The firmwares of
BB MCU 0/1 are also downloaded via the same path like WiFi CPU firmware,
and use the same firmware header format, so add firmware suits to access
them commonly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-6-pkshih@realtek.com
A firmware with v1 format contains many sections to download. Add parser to
read section type, target address, length, checksum and so on, and then
download the section to WiFi CPU with proper location.
The additional dynamic header length named dynamic_hdr_len is used to
skip content of dynamic header containing compiler flags of firmware, which
can help to determine variant firmware build, but currently rtw89 only
use single one variant. So, just skip the content.
The layout of a WiFi CPU firmware with v1 format looks like:
+---------------------------------------+
| Header (12 words) |
+---------------------------------------+
| Section header 1 (4 words) |
| Section header 2 (4 words) |
| Section header 3 (4 words) |
| ... |
+---------------------------------------+
| Dynamic header (variable length) |
+---------------------------------------+
| Data used & pointed by section |
| ... |
+---------------------------------------+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-5-pkshih@realtek.com
New firmware header is used by upcoming WiFi 7 chips to have more
information, so use common field w3[31:24] to determine header version,
and then use corresponding function to read firmware version and commit ID:
rtw89_8852be 0000:03:00.0: Firmware version 0.29.29.1 (799134c3), cmd version 1, type 5
rtw89_8852be 0000:03:00.0: Firmware version 0.29.29.1 (799134c3), cmd version 1, type 3
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-4-pkshih@realtek.com
Original firmware log which is sent via C2H message bloats
code size of firmware and is also length-limited. So we put
some common log into format file, and firmware could use a
log ID and some variables in C2H message to map a formatted
text via pre-designed rule.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-3-pkshih@realtek.com
Commit d50ccc2d39 ("tipc: add 128-bit node identifier") declared but never
implemented tipc_node_id2hash().
Also commit 5c216e1d28 ("tipc: Allow run-time alteration of default link settings")
never implemented tipc_media_set_priority() and tipc_media_set_window(),
commit cad2929dc4 ("tipc: update a binding service via broadcast") only declared
tipc_named_bcast().
Since commit be07f05639 ("tipc: simplify the finalize work queue")
tipc_sched_net_finalize() is removed and declaration is unused.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230802034659.39840-1-yuehaibing@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Deadlock is easily happened while shutdown wlan interface such as run
"ifconfig wlan0 down".
The reason is because when ar->regd_update_work is ran, it will
call wiphy_lock(ar->hw->wiphy) in function ath12k_regd_update() which
is running in workqueue of ieee80211_local queued by ieee80211_queue_work().
Another thread from "ifconfig wlan0 down" will also accuqire the lock
by wiphy_lock(sdata->local->hw.wiphy) in function ieee80211_stop(), and
then it call ieee80211_stop_device() to flush_workqueue(local->workqueue),
this will wait the workqueue of ieee80211_local finished. Then deadlock
will happen easily if the two thread run meanwhile.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230718024724.29120-1-quic_wgong@quicinc.com
When wlan interface is up, and 11d scan is sent to the firmware, then
firmware needs to spend couple of seconds to complete the 11d scan. If
normal scan from user space arrives to ath12k at this moment, then the
normal scan request is also sent to the firmware, but the scan started
event will be reported to ath12k until the 11d scan complete. When timed
out for the scan started in ath12k, ath12k stops the normal scan and the
firmware reports WMI_SCAN_EVENT_DEQUEUED to ath12k for the normal scan.
ath12k has no handler for the event and then timed out for the scan
completed in ath12k_scan_stop(), and ath12k prints the following error
message.
[ 1491.604750] ath12k_pci 0000:02:00.0: failed to receive scan abort comple: timed out
[ 1491.604756] ath12k_pci 0000:02:00.0: failed to stop scan: -110
[ 1491.604758] ath12k_pci 0000:02:00.0: failed to start hw scan: -110
Add a handler for WMI_SCAN_EVENT_DEQUEUED and then complete the scan to
get rid of the above error message.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230717034457.22162-1-quic_wgong@quicinc.com
