[ Upstream commit 7c7b1be19b228b450c2945ec379d7fc6bfef9852 ]
As the driver supports more devices over time the single MODULE_ALIAS
is complete and raises several warnings:
SPI driver ads7846 has no spi_device_id for ti,tsc2046
SPI driver ads7846 has no spi_device_id for ti,ads7843
SPI driver ads7846 has no spi_device_id for ti,ads7845
SPI driver ads7846 has no spi_device_id for ti,ads7873
Fix this by adding a spi_device_id table and removing the manual
MODULE_ALIAS.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240619122703.2081476-1-alexander.stein@ew.tq-group.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a69ce592cbe0417664bc5a075205aa75c2ec1273 ]
The Lenovo N24 on resume becomes stuck in a state where it
sends incorrect packets, causing elantech_packet_check_v4 to fail.
The only way for the device to resume sending the correct packets is for
it to be disabled and then re-enabled.
This change adds a dmi check to trigger this behavior on resume.
Signed-off-by: Jonathan Denose <jdenose@google.com>
Link: https://lore.kernel.org/r/20240503155020.v2.1.Ifa0e25ebf968d8f307f58d678036944141ab17e6@changeid
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38a38f5a36da9820680d413972cb733349400532 ]
When support for Silead touchscreens was orginal added some touchscreens
with older firmware versions only supported 5 fingers and this was made
the default requiring the setting of a "silead,max-fingers=10" uint32
device-property for all touchscreen models which do support 10 fingers.
There are very few models with the old 5 finger fw, so in practice the
setting of the "silead,max-fingers=10" is boilerplate which needs to
be copy and pasted to every touchscreen config.
Reporting that 10 fingers are supported on devices which only support
5 fingers doesn't cause any problems for userspace in practice, since
at max 4 finger gestures are supported anyways. Drop the max_fingers
configuration and simply always assume 10 fingers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20240525193854.39130-2-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b4e0b39182cf5e677c1fc092a3ec40e621c25b6 ]
Grab input->mutex during suspend/resume functions like it is done in
other input drivers. This fixes the following warning during system
suspend/resume cycle on Samsung Exynos5250-based Snow Chromebook:
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1680 at drivers/input/input.c:2291 input_device_enabled+0x68/0x6c
Modules linked in: ...
CPU: 1 PID: 1680 Comm: kworker/u4:12 Tainted: G W 6.6.0-rc5-next-20231009 #14109
Hardware name: Samsung Exynos (Flattened Device Tree)
Workqueue: events_unbound async_run_entry_fn
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x58/0x70
dump_stack_lvl from __warn+0x1a8/0x1cc
__warn from warn_slowpath_fmt+0x18c/0x1b4
warn_slowpath_fmt from input_device_enabled+0x68/0x6c
input_device_enabled from cyapa_gen3_set_power_mode+0x13c/0x1dc
cyapa_gen3_set_power_mode from cyapa_reinitialize+0x10c/0x15c
cyapa_reinitialize from cyapa_resume+0x48/0x98
cyapa_resume from dpm_run_callback+0x90/0x298
dpm_run_callback from device_resume+0xb4/0x258
device_resume from async_resume+0x20/0x64
async_resume from async_run_entry_fn+0x40/0x15c
async_run_entry_fn from process_scheduled_works+0xbc/0x6a8
process_scheduled_works from worker_thread+0x188/0x454
worker_thread from kthread+0x108/0x140
kthread from ret_from_fork+0x14/0x28
Exception stack(0xf1625fb0 to 0xf1625ff8)
...
---[ end trace 0000000000000000 ]---
...
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1680 at drivers/input/input.c:2291 input_device_enabled+0x68/0x6c
Modules linked in: ...
CPU: 1 PID: 1680 Comm: kworker/u4:12 Tainted: G W 6.6.0-rc5-next-20231009 #14109
Hardware name: Samsung Exynos (Flattened Device Tree)
Workqueue: events_unbound async_run_entry_fn
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x58/0x70
dump_stack_lvl from __warn+0x1a8/0x1cc
__warn from warn_slowpath_fmt+0x18c/0x1b4
warn_slowpath_fmt from input_device_enabled+0x68/0x6c
input_device_enabled from cyapa_gen3_set_power_mode+0x13c/0x1dc
cyapa_gen3_set_power_mode from cyapa_reinitialize+0x10c/0x15c
cyapa_reinitialize from cyapa_resume+0x48/0x98
cyapa_resume from dpm_run_callback+0x90/0x298
dpm_run_callback from device_resume+0xb4/0x258
device_resume from async_resume+0x20/0x64
async_resume from async_run_entry_fn+0x40/0x15c
async_run_entry_fn from process_scheduled_works+0xbc/0x6a8
process_scheduled_works from worker_thread+0x188/0x454
worker_thread from kthread+0x108/0x140
kthread from ret_from_fork+0x14/0x28
Exception stack(0xf1625fb0 to 0xf1625ff8)
...
---[ end trace 0000000000000000 ]---
Fixes: d69f0a43c6 ("Input: use input_device_enabled()")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Link: https://lore.kernel.org/r/20231009121018.1075318-1-m.szyprowski@samsung.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf32bceedd0453c70d9d022e2e29f98e446d7161 ]
clang warns about a string overflow in this driver
drivers/input/misc/ims-pcu.c:1802:2: error: 'snprintf' will always be truncated; specified size is 10, but format string expands to at least 12 [-Werror,-Wformat-truncation]
drivers/input/misc/ims-pcu.c:1814:2: error: 'snprintf' will always be truncated; specified size is 10, but format string expands to at least 12 [-Werror,-Wformat-truncation]
Make the buffer a little longer to ensure it always fits.
Fixes: 628329d524 ("Input: add IMS Passenger Control Unit driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240326223825.4084412-7-arnd@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c748a6d77c06a78651030e17da6beb278a1c9470 ]
In order to introduce a pwm api which can be used from atomic context,
we will need two functions for applying pwm changes:
int pwm_apply_might_sleep(struct pwm *, struct pwm_state *);
int pwm_apply_atomic(struct pwm *, struct pwm_state *);
This commit just deals with renaming pwm_apply_state(), a following
commit will introduce the pwm_apply_atomic() function.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> # for input
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Stable-dep-of: 974afccd3794 ("leds: pwm: Disable PWM when going to suspend")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0774d19038c496f0c3602fb505c43e1b2d8eed85 upstream.
If an input device declares too many capability bits then modalias
string for such device may become too long and not fit into uevent
buffer, resulting in failure of sending said uevent. This, in turn,
may prevent userspace from recognizing existence of such devices.
This is typically not a concern for real hardware devices as they have
limited number of keys, but happen with synthetic devices such as
ones created by xen-kbdfront driver, which creates devices as being
capable of delivering all possible keys, since it doesn't know what
keys the backend may produce.
To deal with such devices input core will attempt to trim key data,
in the hope that the rest of modalias string will fit in the given
buffer. When trimming key data it will indicate that it is not
complete by placing "+," sign, resulting in conversions like this:
old: k71,72,73,74,78,7A,7B,7C,7D,8E,9E,A4,AD,E0,E1,E4,F8,174,
new: k71,72,73,74,78,7A,7B,7C,+,
This should allow existing udev rules continue to work with existing
devices, and will also allow writing more complex rules that would
recognize trimmed modalias and check input device characteristics by
other means (for example by parsing KEY= data in uevent or parsing
input device sysfs attributes).
Note that the driver core may try adding more uevent environment
variables once input core is done adding its own, so when forming
modalias we can not use the entire available buffer, so we reduce
it by somewhat an arbitrary amount (96 bytes).
Reported-by: Jason Andryuk <jandryuk@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Tested-by: Jason Andryuk <jandryuk@gmail.com>
Link: https://lore.kernel.org/r/ZjAWMQCJdrxZkvkB@google.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4255447ad34c5c3785fcdcf76cfa0271d6e5ed39 ]
Another Fujitsu-related patch.
In the initial boot stage the integrated keyboard of Fujitsu Lifebook U728
refuses to work and it's not possible to type for example a dm-crypt
passphrase without the help of an external keyboard.
i8042.nomux kernel parameter resolves this issue but using that a PS/2
mouse is detected. This input device is unused even when the i2c-hid-acpi
kernel module is blacklisted making the integrated ELAN touchpad
(04F3:3092) not working at all.
So this notebook uses a hid-over-i2c touchpad which is managed by the
i2c_designware input driver. Since you can't find a PS/2 mouse port on this
computer and you can't connect a PS/2 mouse to it even with an official
port replicator I think it's safe to not use the PS/2 mouse port at all.
Signed-off-by: Szilard Fabian <szfabian@bluemarch.art>
Link: https://lore.kernel.org/r/20240103014717.127307-2-szfabian@bluemarch.art
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80441f76ee67002437db61f3b317ed80cce085d2 ]
The Lenovo Legion Go is a handheld gaming system, similar to a Steam Deck.
It has a gamepad (including rear paddles), 3 gyroscopes, a trackpad,
volume buttons, a power button, and 2 LED ring lights.
The Legion Go firmware presents these controls as a USB hub with various
devices attached. In its default state, the gamepad is presented as an
Xbox controller connected to this hub. (By holding a combination of
buttons, it can be changed to use the older DirectInput API.)
This patch teaches the existing Xbox controller module `xpad` to bind to
the controller in the Legion Go, which enables support for the:
- directional pad,
- analog sticks (including clicks),
- X, Y, A, B,
- start and select (or menu and capture),
- shoulder buttons, and
- rumble.
The trackpad, touchscreen, volume controls, and power button are already
supported via existing kernel modules. Two of the face buttons, the
gyroscopes, rear paddles, and LEDs are not.
After this patch lands, the Legion Go will be mostly functional in Linux,
out-of-the-box. The various components of the USB hub can be synthesized
into a single logical controller (including the additional buttons) in
userspace with [Handheld Daemon](https://github.com/hhd-dev/hhd), which
makes the Go fully functional.
Signed-off-by: Brenton Simpson <appsforartists@google.com>
Link: https://lore.kernel.org/r/20240118183546.418064-1-appsforartists@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 180a8f12c21f41740fee09ca7f7aa98ff5bb99f8 ]
Some devices list 3 Gpio resources in the ACPI resource list for
the touchscreen:
1. GpioInt resource pointing to the GPIO used for the interrupt
2. GpioIo resource pointing to the reset GPIO
3. GpioIo resource pointing to the GPIO used for the interrupt
Note how the third extra GpioIo resource really is a duplicate
of the GpioInt provided info.
Ignore this extra GPIO, treating this setup the same as gpio_count == 2 &&
gpio_int_idx == 0 fixes the touchscreen not working on the Thunderbook
Colossus W803 rugged tablet and likely also on the CyberBook_T116K.
Reported-by: Maarten van der Schrieck
Closes: https://gitlab.com/AdyaAdya/goodix-touchscreen-linux-driver/-/issues/22
Suggested-by: Maarten van der Schrieck
Tested-by: Maarten van der Schrieck
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231223141650.10679-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a60e6c3918d20848906ffcdfcf72ca6a8cfbcf2e upstream.
When closing the laptop lid with an external screen connected, the mouse
pointer has a constant movement to the lower right corner. Opening the
lid again stops this movement, but after that the touchpad does no longer
register clicks.
The touchpad is connected both via i2c-hid and PS/2, the predecessor of
this device (NS70MU) has the same layout in this regard and also strange
behaviour caused by the psmouse and the i2c-hid driver fighting over
touchpad control. This fix is reusing the same workaround by just
disabling the PS/2 aux port, that is only used by the touchpad, to give the
i2c-hid driver the lone control over the touchpad.
v2: Rebased on current master
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231205163602.16106-1-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c1f342f35f820b33390571293498c3e2e9bc77ec ]
Observed on dmesg of my laptop I see the following
output:
[ 19.898700] psmouse serio1: synaptics: queried max coordinates: x [..5678], y [..4694]
[ 19.936057] psmouse serio1: synaptics: queried min coordinates: x [1266..], y [1162..]
[ 19.936076] psmouse serio1: synaptics: Your touchpad (PNP: LEN0411 PNP0f13) says it can support a different bus. If i2c-hid and hid-rmi are not used, you might want to try setting psmouse.synaptics_intertouch to 1 and report this to linux-input@vger.kernel.org.
[ 20.008901] psmouse serio1: synaptics: Touchpad model: 1, fw: 10.32, id: 0x1e2a1, caps: 0xf014a3/0x940300/0x12e800/0x500000, board id: 3471, fw id: 2909640
[ 20.008925] psmouse serio1: synaptics: serio: Synaptics pass-through port at isa0060/serio1/input0
[ 20.053344] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7
[ 20.397608] mousedev: PS/2 mouse device common for all mice
This patch will add its pnp id to the smbus list to
produce the setup of intertouch for the device.
Signed-off-by: José Pekkarinen <jose.pekkarinen@foxhound.fi>
Link: https://lore.kernel.org/r/20231114063607.71772-1-jose.pekkarinen@foxhound.fi
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ea3715941a9b7d816a1e9096ac0577900af2a69e upstream.
This add a mapping for the airplane mode button on the TUXEDO Pulse Gen3.
While it is physically a key it behaves more like a switch, sending a key
down on first press and a key up on 2nd press. Therefor the switch event
is used here. Besides this behaviour it uses the HID usage-id 0xc6
(Wireless Radio Button) and not 0xc8 (Wireless Radio Slider Switch), but
since neither 0xc6 nor 0xc8 are currently implemented at all in
soc_button_array this not to standard behaviour is not put behind a quirk
for the moment.
Signed-off-by: Christoffer Sandberg <cs@tuxedo.de>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Link: https://lore.kernel.org/r/20231215171718.80229-1-wse@tuxedocomputers.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 59b6a747e2d39227ac2325c5e29d6ab3bb070c2a ]
Check the return value of i2c_add_adapter. Static analysis revealed that
the function did not properly handle potential failures of
i2c_add_adapter, which could lead to partial initialization of the I2C
adapter and unstable operation.
Signed-off-by: Haoran Liu <liuhaoran14@163.com>
Link: https://lore.kernel.org/r/20231203164653.38983-1-liuhaoran14@163.com
Fixes: d7535ffa42 ("Input: driver for microcontroller keys on the iPaq h3xxx")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pull input fixes from Dmitry Torokhov:
- a reworked way for handling reset delay on SMBus-connected Synaptics
touchpads (the original one, while being correct, uncovered an old
bug in fallback to PS/2 code that was fixed separately; the new one
however avoids having delay in serio port "fast" resume, and instead
has the wait in the RMI4 code)
- a fix for potential crashes when devices with Elan controllers (and
Synaptics) fall back to PS/2 code. Can't be hit without the original
patch above, but still good to have it fixed
- a couple new device IDs in xpad Xbox driver
- another quirk for Goodix driver to deal with stuff vendors put in
ACPI tables
- a fix for use-after-free on disconnect for powermate driver
- a quirk to not initialize PS/2 mouse port on Fujitsu Lifebook E5411
laptop as it makes keyboard not usable and the device uses
hid-over-i2c touchpad anyways
* tag 'input-for-v6.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: powermate - fix use-after-free in powermate_config_complete
Input: xpad - add PXN V900 support
Input: synaptics-rmi4 - handle reset delay when using SMBus trsnsport
Input: psmouse - fix fast_reconnect function for PS/2 mode
Revert "Input: psmouse - add delay when deactivating for SMBus mode"
Input: goodix - ensure int GPIO is in input for gpio_count == 1 && gpio_int_idx == 0 case
Input: i8042 - add Fujitsu Lifebook E5411 to i8042 quirk table
Input: xpad - add HyperX Clutch Gladiate Support
Touch controllers need some time after receiving reset command for the
firmware to finish re-initializing and be ready to respond to commands
from the host. The driver already had handling for the post-reset delay
for I2C and SPI transports, this change adds the handling to
SMBus-connected devices.
SMBus devices are peculiar because they implement legacy PS/2
compatibility mode, so reset is actually issued by psmouse driver on the
associated serio port, after which the control is passed to the RMI4
driver with SMBus companion device.
Note that originally the delay was added to psmouse driver in
92e24e0e57 ("Input: psmouse - add delay when deactivating for SMBus
mode"), but that resulted in an unwanted delay in "fast" reconnect
handler for the serio port, so it was decided to revert the patch and
have the delay being handled in the RMI4 driver, similar to the other
transports.
Tested-by: Jeffery Miller <jefferymiller@google.com>
Link: https://lore.kernel.org/r/ZR1yUFJ8a9Zt606N@penguin
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When the SMBus connection is attempted psmouse_smbus_init() sets
the fast_reconnect pointer to psmouse_smbus_reconnecti(). If SMBus
initialization fails, elantech_setup_ps2() and synaptics_init_ps2() will
fallback to PS/2 mode, replacing the psmouse private data. This can cause
issues on resume, since psmouse_smbus_reconnect() expects to find an
instance of struct psmouse_smbus_dev in psmouse->private.
The issue was uncovered when in 92e24e0e57 ("Input: psmouse - add
delay when deactivating for SMBus mode") psmouse_smbus_reconnect()
started attempting to use more of the data structure. The commit was
since reverted, not because it was at fault, but because there was found
a better way of doing what it was attempting to do.
Fix the problem by resetting the fast_reconnect pointer in psmouse
structure in elantech_setup_ps2() and synaptics_init_ps2() when the PS/2
mode is used.
Reported-by: Thorsten Leemhuis <linux@leemhuis.info>
Tested-by: Thorsten Leemhuis <linux@leemhuis.info>
Signed-off-by: Jeffery Miller <jefferymiller@google.com>
Fixes: bf232e460a ("Input: psmouse-smbus - allow to control psmouse_deactivate")
Link: https://lore.kernel.org/r/20231005002249.554877-1-jefferymiller@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit 92e24e0e57.
While the patch itself is correct, it uncovered an issue with fallback
to PS/2 mode, where we were leaving psmouse->fast_reconnect handler set
to psmouse_smbus_reconnect(), which caused crashes.
While discussing various approaches to fix the issue it was noted that
this patch ass undesired delay in the "fast" resume path of PS/2 device,
and it would be better to actually use "reset_delay" option defined in
struct rmi_device_platform_data and have RMI code handle it for SMBus
transport as well. So this patch is being reverted to deal with crashes
and a better solution will be merged shortly.
Reported-by: Thorsten Leemhuis <linux@leemhuis.info>
Closes: https://lore.kernel.org/all/ca0109fa-c64b-43c1-a651-75b294d750a1@leemhuis.info/
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add a special case for gpio_count == 1 && gpio_int_idx == 0 to
goodix_add_acpi_gpio_mappings().
It seems that on newer x86/ACPI devices the reset and irq GPIOs are no
longer listed as GPIO resources instead there is only 1 GpioInt resource
and _PS0 does the whole reset sequence for us.
This means that we must call acpi_device_fix_up_power() on these devices
to ensure that the chip is reset before we try to use it.
This part was already fixed in commit 3de93e6ed2 ("Input: goodix - call
acpi_device_fix_up_power() in some cases") by adding a call to
acpi_device_fix_up_power() to the generic "Unexpected ACPI resources"
catch all.
But it turns out that this case on some hw needs some more special
handling. Specifically the firmware may bootup with the IRQ pin in
output mode. The reset sequence from ACPI _PS0 (executed by
acpi_device_fix_up_power()) should put the pin in input mode,
but the GPIO subsystem has cached the direction at bootup, causing
request_irq() to fail due to gpiochip_lock_as_irq() failure:
[ 9.119864] Goodix-TS i2c-GDIX1002:00: Unexpected ACPI resources: gpio_count 1, gpio_int_idx 0
[ 9.317443] Goodix-TS i2c-GDIX1002:00: ID 911, version: 1060
[ 9.321902] input: Goodix Capacitive TouchScreen as /devices/pci0000:00/0000:00:17.0/i2c_designware.4/i2c-5/i2c-GDIX1002:00/input/input8
[ 9.327840] gpio gpiochip0: (INT3453:00): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
[ 9.327856] gpio gpiochip0: (INT3453:00): unable to lock HW IRQ 26 for IRQ
[ 9.327861] genirq: Failed to request resources for GDIX1002:00 (irq 131) on irqchip intel-gpio
[ 9.327912] Goodix-TS i2c-GDIX1002:00: request IRQ failed: -5
Fix this by adding a special case for gpio_count == 1 && gpio_int_idx == 0
which adds an ACPI GPIO lookup table for the int GPIO even though we cannot
use it for reset purposes (as there is no reset GPIO).
Adding the lookup will make the gpiod_int = gpiod_get(..., GPIOD_IN) call
succeed, which will explicitly set the direction to input fixing the issue.
Note this re-uses the acpi_goodix_int_first_gpios[] lookup table, since
there is only 1 GPIO in the ACPI resources the reset entry in that
lookup table will amount to a no-op.
Reported-and-tested-by: Michael Smith <1973.mjsmith@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231003215144.69527-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In the initial boot stage the integrated keyboard of Fujitsu Lifebook E5411
refuses to work and it's not possible to type for example a dm-crypt
passphrase without the help of an external keyboard.
i8042.nomux kernel parameter resolves this issue but using that a PS/2
mouse is detected. This input device is unused even when the i2c-hid-acpi
kernel module is blacklisted making the integrated ELAN touchpad
(04F3:308A) not working at all.
Since the integrated touchpad is managed by the i2c_designware input
driver in the Linux kernel and you can't find a PS/2 mouse port on the
computer I think it's safe to not use the PS/2 mouse port at all.
Signed-off-by: Szilard Fabian <szfabian@bluemarch.art>
Link: https://lore.kernel.org/r/20231004011749.101789-1-szfabian@bluemarch.art
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- a new driver for Azoteq IQS7210A/7211A/E touch controllers
- support for Azoteq IQS7222D variant added to iqs7222 driver
- support for touch keys functionality added to Melfas MMS114 driver
- new hardware IDs added to exc3000 and Goodix drivers
- xpad driver gained support for GameSir T4 Kaleid Controller
- a fix for xpad driver to properly support some third-party
controllers that need a magic packet to start properly
- a fix for psmouse driver to more reliably switch to RMI4 mode on
devices that use native RMI4/SMbus protocol
- a quirk for i8042 for TUXEDO Gemini 17 Gen1/Clevo PD70PN laptops
- multiple drivers have been updated to make use of devm and other
newer APIs such as dev_err_probe(), devm_regulator_get_enable(), and
others.
* tag 'input-for-v6.6-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (83 commits)
Input: goodix - add support for ACPI ID GDX9110
Input: rpckbd - fix the return value handle for platform_get_irq()
Input: tca6416-keypad - switch to using input core's polling features
Input: tca6416-keypad - convert to use devm_* api
Input: tca6416-keypad - fix interrupt enable disbalance
Input: tca6416-keypad - rely on I2C core to set up suspend/resume
Input: tca6416-keypad - always expect proper IRQ number in i2c client
Input: lm8323 - convert to use devm_* api
Input: lm8323 - rely on device core to create kp_disable attribute
Input: qt2160 - convert to use devm_* api
Input: qt2160 - do not hard code interrupt trigger
Input: qt2160 - switch to using threaded interrupt handler
Input: qt2160 - tweak check for i2c adapter functionality
Input: psmouse - add delay when deactivating for SMBus mode
Input: mcs-touchkey - fix uninitialized use of error in mcs_touchkey_probe()
Input: qt1070 - convert to use devm_* api
Input: mcs-touchkey - convert to use devm_* api
Input: amikbd - convert to use devm_* api
Input: lm8333 - convert to use devm_* api
Input: mms114 - add support for touch keys
...
