In an ideal world, when someone is passed an iov_iter and returns X bytes,
then X bytes would have been consumed/advanced from the iov_iter. But we
have use cases that always consume the entire iterator, a few examples
of that are iomap and bdev O_DIRECT. This means we cannot rely on the
state of the iov_iter once we've called ->read_iter() or ->write_iter().
This would be easier if we didn't always have to deal with truncate of
the iov_iter, as rewinding would be trivial without that. We recently
added a commit to track the truncate state, but that grew the iov_iter
by 8 bytes and wasn't the best solution.
Implement a helper to save enough of the iov_iter state to sanely restore
it after we've called the read/write iterator helpers. This currently
only works for IOVEC/BVEC/KVEC as that's all we need, support for other
iterator types are left as an exercise for the reader.
Link: https://lore.kernel.org/linux-fsdevel/CAHk-=wiacKV4Gh-MYjteU0LwNBSGpWrK-Ov25HdqB1ewinrFPg@mail.gmail.com/
Signed-off-by: Jens Axboe <axboe@kernel.dk>
DRM_FBDEV_EMULATION previously selected FB and was default y as long as DRM
was enabled. In commit f611b1e762 ("drm: Avoid circular dependencies for
CONFIG_FB") the select was replaced with a depends on FB, disabling the
drivers that depended on it.
Renable FB so we get back FB_EFI, FB_WM8505, FB_SH_MOBILE_LCDC, FB_SIMPLE and
VIDEO_VIVID.
It must be set to y and not a module as the test driver VIDEO_VIVID
requires it to be built in.
Link: https://lore.kernel.org/r/CAK8P3a18EdBKQdGDOZc9cPKsf=hY8==v2cO0DBE_tyd82Uq-Ng@mail.gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some drivers have not been built as they gained dependencies in kconfig but those
dependencies were not added to the defconfig.
The MSM pinctrl drivers fell out of the defconfig as of commit be117ca322
("pinctrl: qcom: Kconfig: Rework PINCTRL_MSM to be a depenency rather then a
selected config"). Add PINCTRL_MSM so these stay enabled.
EDAC depends on RAS, so enable it to ensure the EDAC drivers stay
enabled.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This reverts commit d7807a9adf.
As mentioned in https://lkml.org/lkml/2021/9/13/1819
5 years old commit 919483096b ("ipv4: fix memory leaks in ip_cmsg_send() callers")
was a correct fix.
ip_cmsg_send() can loop over multiple cmsghdr()
If IP_RETOPTS has been successful, but following cmsghdr generates an error,
we do not free ipc.ok
If IP_RETOPTS is not successful, we have freed the allocated temporary space,
not the one currently in ipc.opt.
Sure, code could be refactored, but let's not bring back old bugs.
Fixes: d7807a9adf ("Revert "ipv4: fix memory leaks in ip_cmsg_send() callers"")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit
time") may directly retrans a multiple segments TSO/GSO packet without
split, Since this commit, we can no longer assume that a retransmitted
packet is a single segment.
This patch fixes the tp->undo_retrans accounting in tcp_sacktag_one()
that use the actual segments(pcount) of the retransmitted packet.
Before that commit (10d3be5692), the assumption underlying the
tp->undo_retrans-- seems correct.
Fixes: 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit time")
Signed-off-by: zhenggy <zhenggy@chinatelecom.cn>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 53b7670e57 ("sparc: factor the dma coherent mapping into
helper") lost the page align for the calls to dma_make_coherent and
srmmu_unmapiorange. The latter cannot handle a non page aligned len
argument.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Daniel Borkmann says:
====================
pull-request: bpf 2021-09-14
The following pull-request contains BPF updates for your *net* tree.
We've added 7 non-merge commits during the last 13 day(s) which contain
a total of 18 files changed, 334 insertions(+), 193 deletions(-).
The main changes are:
1) Fix mmap_lock lockdep splat in BPF stack map's build_id lookup, from Yonghong Song.
2) Fix BPF cgroup v2 program bypass upon net_cls/prio activation, from Daniel Borkmann.
3) Fix kvcalloc() BTF line info splat on oversized allocation attempts, from Bixuan Cui.
4) Fix BPF selftest build of task_pt_regs test for arm64/s390, from Jean-Philippe Brucker.
5) Fix BPF's disasm.{c,h} to dual-license so that it is aligned with bpftool given the former
is a build dependency for the latter, from Daniel Borkmann with ACKs from contributors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Staged submission consists of multiple command submissions.
In order to be explicit, driver should return a single cs sequence
for every cs in the submission, or else user may try to wait on
an internal CS rather than waiting for the whole submission.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add handling for case where the user doesn't set wait offset,
and keeps it as 0. In such a case the driver will decrement one
from this zero value which will cause the code to wait for
wrong number of signals.
The solution is to treat this case as in legacy wait cs,
and wait for the next signal.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As user can send wrong arguments to multi CS API, we rate limit
the amount of errors dumped to dmesg, in addition we change the
severity to warning.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Couple of fixes to the LBW RR configuration:
1. Add missing configuration of the SM RR registers in the DMA_IF.
2. Remove HBW range that doesn't belong.
3. Add entire gap + DBG area, from end of TPC7 to end of entire
DBG space.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As collective wait operation is required only when NIC ports are
available, we disable the option to submit a CS in case all the ports
are disabled, which is the current situation in the upstream driver.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Due to FLR scenario when running inside a VM, we must not use indirect
MSI because it might cause some issues on VM destroy.
In a VM we use single MSI mode in contrary to multi MSI mode which is
used in bare-metal.
Hence direct MSI should be used in single MSI mode only.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In case of single staged cs with both first/last indications
set, we reach a scenario where in cs_release function flow
we don't cancel the TDR work before freeing the cs memory,
this lead to kernel OOPs since when the timer expires
the work pointer will be freed already.
In addition treat wait encaps cs "not found" handle
as "OK" for the user in order to keep the user interface
for both legacy and encpas signal/wait features the same.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We have a potential race where a user interrupt can be received
in between user thread value comparison and before request was
added to wait list. This means that if no consecutive interrupt
will be received, user thread will timeout and fail.
The solution is to add the request to wait list before we
perform the comparison.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7793 datasheet: " The DOUT/RDY falling edge can be
used as an interrupt to a processor"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-4-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Correct IRQ flag here is falling.
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7780 datasheet: " The DOUT/Figure 22 RDY falling edge
can be used as an interrupt to a processor"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-3-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
IRQ type in ad_sigma_delta_info struct was missing.
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7192 datasheet: "The DOUT/RDY falling edge can be used
as an interrupt to a processor,"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-2-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently when a timeout occurs in rzg2l_adc_hw_init the error -EBUSY is
assigned to ret but the error code is used as the function is hard-coded
to return 0. The variable ret is 0 before entering the while-loop hence
the fix is just to return ret at the end of the function to return the
success 0 or -EBUSY return code.
Addresses-Coverity: ("Unused value")
Fixes: d484c21bac ("iio: adc: Add driver for Renesas RZ/G2L A/D converter")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210817172111.495897-1-colin.king@canonical.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There have been reports of approximately a 0.9%-1.7% failure rate in SMU
communication timeouts with s0i3 entry on some OEM designs. Currently
the design in amd-pmc is to try every 100us for up to 20ms.
However the GPU driver which also communicates with the SMU using a
mailbox register which the driver polls every 1us for up to 2000ms.
In the GPU driver this was increased by commit 055162645a ("drm/amd/pm:
increase time out value when sending msg to SMU")
Increase the maximum timeout used by amd-pmc to 2000ms to match this
behavior. This has been shown to improve the stability for machines
that randomly have failures.
Cc: stable@kernel.org
Reported-by: Julian Sikorski <belegdol@gmail.com>
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1629
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20210914020115.655-1-mario.limonciello@amd.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
tx-fifo-resize is now added by default by the dwc3-qcom driver
to the SNPS DWC3 child node.
So, lets drop the tx-fifo-resize property from dwc3-qcom nodes
as having it there will cause the dwc3-qcom driver to error and
abort probe with:
[ 1.362938] dwc3-qcom 8af8800.usb: unable to add property
[ 1.368405] dwc3-qcom 8af8800.usb: failed to register DWC3 Core, err=-17
Fixes: cefdd52fa0 ("usb: dwc3: dwc3-qcom: Enable tx-fifo-resize property by default")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Link: https://lore.kernel.org/r/20210902220325.1783567-1-robimarko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch initializes and enables speaker output on the Lenovo Legion 7i
15IMHG05, Yoga 7i 14ITL5/15ITL5, and 13s Gen2 series of laptops using the
HDA verb sequence specific to each model.
Speaker automute is suppressed for the Lenovo Legion 7i 15IMHG05 to avoid
breaking speaker output on resume and when devices are unplugged from its
headphone jack.
Thanks to: Andreas Holzer, Vincent Morel, sycxyc, Max Christian Pohle and
all others that helped.
[ minor coding style fixes by tiwai ]
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208555
Signed-off-by: Cameron Berkenpas <cam@neo-zeon.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210913212627.339362-1-cam@neo-zeon.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
'set_signals()' in synclink_gt.c conflicts with an exported symbol
in arch/um/, so change set_signals() to set_gtsignals(). Keep
the function names similar by also changing get_signals() to
get_gtsignals().
../drivers/tty/synclink_gt.c:442:13: error: conflicting types for ‘set_signals’
static void set_signals(struct slgt_info *info);
^~~~~~~~~~~
In file included from ../include/linux/irqflags.h:16:0,
from ../include/linux/spinlock.h:58,
from ../include/linux/mm_types.h:9,
from ../include/linux/buildid.h:5,
from ../include/linux/module.h:14,
from ../drivers/tty/synclink_gt.c:46:
../arch/um/include/asm/irqflags.h:6:5: note: previous declaration of ‘set_signals’ was here
int set_signals(int enable);
^~~~~~~~~~~
Fixes: 705b6c7b34 ("[PATCH] new driver synclink_gt")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210902003806.17054-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Isochronous endpoints, the SS companion descriptor's
wBytesPerInterval field is required to reserve bus time in order
to transmit the required payload during the service interval.
If left at 0, the UAC2 function is unable to transact data on its
playback or capture endpoints in SuperSpeed mode.
Since f_uac2 currently does not support any bursting this value can
be exactly equal to the calculated wMaxPacketSize.
Tested with Windows 10 as a host.
Fixes: f8cb3d556b ("usb: f_uac2: adds support for SS and SSP")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210909174811.12534-3-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The f_uac2 function fails to enumerate when connected in SuperSpeed
due to the feedback endpoint missing the companion descriptor.
Add a new ss_epin_fback_desc_comp descriptor and append it behind the
ss_epin_fback_desc both in the static definition of the ss_audio_desc
structure as well as its dynamic construction in setup_headers().
Fixes: 24f779dac8 ("usb: gadget: f_uac2/u_audio: add feedback endpoint support")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210909174811.12534-2-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been observed with certain PCIe USB cards (like Inateck connected
to AM64 EVM or J7200 EVM) that as soon as the primary roothub is
registered, port status change is handled even before xHC is running
leading to cold plug USB devices not detected. For such cases, registering
both the root hubs along with the second HCD is required. Add support for
deferring roothub registration in usb_add_hcd(), so that both primary and
secondary roothubs are registered along with the second HCD.
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210909064200.16216-2-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According USB spec each ISOC transaction should be performed in a
designated for that transaction interval. On bus errors or delays
in operating system scheduling of client software can result in no
packet being transferred for a (micro)frame. An error indication
should be returned as status to the client software in such a case.
Current implementation in case of missed/dropped interval send same
data in next possible interval instead of reporting missed isoc.
This fix complete requests with -ENODATA if interval elapsed.
HSOTG core in BDMA and Slave modes haven't HW support for
(micro)frames tracking, this is why SW should care about tracking
of (micro)frames. Because of that method and consider operating
system scheduling delays, added few additional checking's of elapsed
target (micro)frame:
1. Immediately before enabling EP to start transfer.
2. With any transfer completion interrupt.
3. With incomplete isoc in/out interrupt.
4. With EP disabled interrupt because of incomplete transfer.
5. With OUT token received while EP disabled interrupt (for OUT
transfers).
6. With NAK replied to IN token interrupt (for IN transfers).
As part of ISOC flow, additionally fixed 'current' and 'target' frame
calculation functions. In HS mode SOF limits provided by DSTS register
is 0x3fff, but in non HS mode this limit is 0x7ff.
Tested by internal tool which also using for dwc3 testing.
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/95d1423adf4b0f68187c9894820c4b7e964a3f7f.1631175721.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
