commit 0f4da2d77e upstream.
"hostap: Protect against initialization interrupt" (which reinstated
"wireless: hostap, fix oops due to early probing interrupt")
reintroduced Bug 16111. This is because hostap_pci wasn't setting
dev->base_addr, which is now checked in prism2_interrupt. As a result,
initialization was failing for PCI-based hostap devices. This corrects
that oversight.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit f880c2050f upstream.
Michael reported that p54* never really entered power
save mode, even tough it was enabled.
It turned out that upon a power save mode change the
firmware will set a special flag onto the last outgoing
frame tx status (which in this case is almost always the
designated PSM nullfunc frame). This flag confused the
driver; It erroneously reported transmission failures
to the stack, which then generated the next nullfunc.
and so on...
Reported-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 904879748d upstream.
The 5 GHz CTL indexes were not being read for all hardware
devices due to the masking out through the CTL_MODE_M mask
being one bit too short. Without this the calibrated regulatory
maximum values were not being picked up when devices operate
on 5 GHz in HT40 mode. The final output power used for Atheros
devices is the minimum between the calibrated CTL values and
what CRDA provides.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 6ccf15a1a7 upstream.
Atheros PCIe wireless cards handled by ath5k do require L0s disabled.
For distributions shipping with CONFIG_PCIEASPM (this will be enabled
by default in the future in 2.6.36) this will also mean both L1 and L0s
will be disabled when a pre 1.1 PCIe device is detected. We do know L1
works correctly even for all ath5k pre 1.1 PCIe devices though but cannot
currently undue the effect of a blacklist, for details you can read
pcie_aspm_sanity_check() and see how it adjusts the device link
capability.
It may be possible in the future to implement some PCI API to allow
drivers to override blacklists for pre 1.1 PCIe but for now it is
best to accept that both L0s and L1 will be disabled completely for
distributions shipping with CONFIG_PCIEASPM rather than having this
issue present. Motivation for adding this new API will be to help
with power consumption for some of these devices.
Example of issues you'd see:
- On the Acer Aspire One (AOA150, Atheros Communications Inc. AR5001
Wireless Network Adapter [168c:001c] (rev 01)) doesn't work well
with ASPM enabled, the card will eventually stall on heavy traffic
with often 'unsupported jumbo' warnings appearing. Disabling
ASPM L0s in ath5k fixes these problems.
- On the same card you would see a storm of RXORN interrupts
even though medium is idle.
Credit for root causing and fixing the bug goes to Jussi Kivilinna.
Cc: David Quan <David.Quan@atheros.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit d28232b461 upstream.
Fix possible double priv->mutex lock introduced by commit
a69b03e941
"iwlwifi: cancel scan watchdog in iwl_bg_abort_scan" .
We can not call cancel_delayed_work_sync(&priv->scan_check) with
priv->mutex locked because workqueue function iwl_bg_scan_check()
take that lock internally.
We do not need to synchronize when canceling priv->scan_check work.
We can avoid races (sending double abort command or send no
command at all) using STATUS_SCAN_ABORT bit. Moreover
current iwl_bg_scan_check() code seems to be broken, as
we should not send abort commands when currently aborting.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 4cee78614c upstream.
When an aggregation session is being cleaned up, while the tx status
for some frames is being processed, the TID is flushed and its buffers
are sent out.
Unfortunately that left the pending un-acked frames unprocessed, thus
leaking buffers. Fix this by reordering the code so that those frames
are processed first, before the TID is flushed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit f860d526eb upstream.
When issuing a reset, the TSF value is lost in the hardware because of
the 913x specific cold reset. As with some AR9280 cards, the TSF needs
to be preserved in software here.
Additionally, there's an issue that frequently prevents a successful
TSF write directly after the chip reset. In this case, repeating the
TSF write after the initval-writes usually works.
This patch detects failed TSF writes and recovers from them, taking
into account the delay caused by the initval writes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 03b4776c40 upstream.
PDADC values were only generated for values surrounding the target
index, however not for the target index itself, leading to a minor
error in the generated curve.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit b561e8274f upstream.
The flow id (scd_flow) in a compressed BA packet should match the txq_id
of the queue from which the aggregated packets were sent. However, in
some hardware like the 1000 series, sometimes the flow id is 0 for the
txq_id (10 to 19). This can cause the annoying message:
[ 2213.306191] iwlagn 0000:01:00.0: Received BA when not expected
[ 2213.310178] iwlagn 0000:01:00.0: Read index for DMA queue txq id (0),
index 5, is out of range [0-256] 7 7.
And even worse, if agg->wait_for_ba is true when the bad BA is arriving,
this can cause system hang due to NULL pointer dereference because the
code is operating in a wrong tx queue!
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Pradeep Kulkarni <pradeepx.kulkarni@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit d6a574ff6b upstream.
Use an irq spinlock to hold off the IRQ handler until
enough early card init is complete such that the handler
can run without faulting.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 3a37495268 upstream.
If bit 29 is set, MAC H/W can attempt to decrypt the received aggregate
with WEP or TKIP, eventhough the received frame may be a CRC failed
corrupted frame. If this bit is set, H/W obeys key type in keycache.
If it is not set and if the key type in keycache is neither open nor
AES, H/W forces key type to be open. But bit 29 should be set to 1
for AsyncFIFO feature to encrypt/decrypt the aggregate with WEP or TKIP.
Reported-by: Johan Hovold <johan.hovold@lundinova.se>
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: Ranga Rao Ravuri <ranga.ravuri@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 14acdde6e5 upstream.
The newer single chip hardware family of chipsets have not been
experiencing issues with power saving set by default with recent
fixes merged (even into stable). The remaining issues are only
reported with AR5416 and since enabling PS by default can increase
power savings considerably best to take advantage of that feature
as this has been tested properly.
For more details on this issue see the bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=14267
We leave AR5416 with PS disabled by default, that seems to require
some more work.
Cc: Peter Stuge <peter@stuge.se>
Cc: Justin P. Mattock <justinmattock@gmail.com>
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 9637e516d1 upstream.
Jumbo frames are not supported, and if they are seen it is likely
a bogus frame so just silently discard them instead of warning on
them all time. Also, instead of dropping them immediately though
move the check *after* we check for all sort of frame errors. This
should enable us to discard these frames if the hardware picks
other bogus items first. Lets see if we still get those jumbo
counters increasing still with this.
Jumbo frames would happen if we tell hardware we can support
a small 802.11 chunks of DMA'd frame, hardware would split RX'd
frames into parts and we'd have to reconstruct them in software.
This is done with USB due to the bulk size but with ath5k we
already provide a good limit to hardware and this should not be
happening.
This is reported quite often and if it fills the logs then this
needs to be addressed and to avoid spurious reports.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit ac592574a5 upstream.
Update the PCI_ID list for 5xx0 series.
Remove all the PCI_IDs which never made into production or not longer in
production.
Also make sure the supported bands(a/b/g/n) match specified PCI_IDs
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 3d79b2a9ee upstream.
We currently have this check as a BUG_ON, which is being hit by people.
Previously it was an error with a recalculation if not current, return that
code.
The BUG_ON was introduced by:
commit 3110bef78c
Author: Guy Cohen <guy.cohen@intel.com>
Date: Tue Sep 9 10:54:54 2008 +0800
iwlwifi: Added support for 3 antennas
... the portion adding the BUG_ON is reverted since we are encountering the error
and BUG_ON was created with assumption that error is not encountered.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 45d427001b upstream.
Error checking for aggregation frames should go into aggregation queue,
if aggregation queue not available, use legacy queue instead.
Also make sure the aggregation queue is available to activate,
if driver and mac80211 is out-of-sync, try to disable the queue and
sync-up with mac80211.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 6b5dcccb49 upstream.
Commit 56d1de0a21, "ath5k: clean up
filter flags setting" introduced a regression in monitor mode such
that the promisc filter flag would get lost.
Although we set the promisc flag when it changed, we did not
preserve it across subsequent calls to configure_filter. This patch
restores the original functionality.
Bisected-by: weedy2887@gmail.com
Tested-by: weedy2887@gmail.com
Tested-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 879999cec9 upstream.
While ar9170's USB transport packet size is currently set to 8KiB,
the PHY is capable of receiving AMPDUs with up to 64KiB.
Such a large frame will be split over several rx URBs and
exceed the previously allocated space for rx stream reconstruction.
This patch increases the buffer size to 64KiB which is
in fact the phy & rx stream designed size limit.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=15591
Reported-by: Christian Mehlis <mehlis@inf.fu-berlin.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 94d0bbe849 upstream.
This patch adds the following 5 entries to the usbid device table:
* Netgear WNA1000
* Proxim ORiNOCO Dual Band 802.11n USB Adapter
* 3Com Dual Band 802.11n USB Adapter
* H3C Dual Band 802.11n USB Adapter
* WNC Generic 11n USB dongle
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit d989ff7cf8 upstream.
When reporting Tx status, indicate that only one rate was used.
Otherwise, the rate is frozen at rate index 0 (i.e. 1Mb/s).
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Johannes' patch 34e8950 titled:
mac80211: allow station add/remove to sleep
changed the way mac80211 adds and removes peers. The new
sta_add() / sta_remove() callbacks allowed the driver callbacks
to sleep. Johannes also ported ath9k to use sta_add() / sta_remove()
via the patch 4ca7786 titled:
ath9k: convert to new station add/remove callbacks
but this patch forgot to address a change in locking issue which
Ming Lei eventually found on his 2.6.33-wl #12 build. The 2.6.33-wl
build includes code for the 802.11 subsystem for 2.6.34 though so did
already have the above two patches (ath9k_sta_remove() on his trace),
the 2.6.33 kernel did not however have these two patches. Ming eventually
cured his lockdep warnign via the patch a9f042c titled:
ath9k: fix lockdep warning when unloading module
This went in to 2.6.34 and although it was not marked as a stable
fix it did get trickled down and applied on both 2.6.33 and 2.6.32.
In review, the culprits:
mac80211: allow station add/remove to sleep
git describe --contains 34e895075e
v2.6.34-rc1~233^2~49^2~107
ath9k: convert to new station add/remove callbacks
git describe --contains 4ca778605c
v2.6.34-rc1~233^2~49^2~10
ath9k: fix lockdep warning when unloading module
This last one trickled down to 2.6.33 (OK), 2.6.33 (invalid) and 2.6.32 (invalid).
git describe --contains a9f042cbe5
v2.6.34-rc2~48^2~77^2~7
git describe --contains 0524bcfa80
v2.6.33.2~125
git describe --contains 0dcc9985f3
v2.6.32.11~79
The patch titled "ath9k: fix lockdep warning when unloading module"
should be reverted on both 2.6.33 and 2.6.32 as it is invalid and
actually ended up causing the following warning:
ADDRCONF(NETDEV_CHANGE): wlan31: link becomes ready
phy0: WMM queue=2 aci=0 acm=0 aifs=3 cWmin=15 cWmax=1023 txop=0
phy0: WMM queue=3 aci=1 acm=0 aifs=7 cWmin=15 cWmax=1023 txop=0
phy0: WMM queue=1 aci=2 acm=0 aifs=2 cWmin=7 cWmax=15 txop=94
phy0: WMM queue=0 aci=3 acm=0 aifs=2 cWmin=3 cWmax=7 txop=47
phy0: device now idle
------------[ cut here ]------------
WARNING: at kernel/softirq.c:143 local_bh_enable_ip+0x7b/0xa0()
Hardware name: 7660A14
Modules linked in: ath9k(-) mac80211 ath cfg80211 <whatever-bleh-etc>
Pid: 2003, comm: rmmod Not tainted 2.6.32.11 #6
Call Trace:
[<ffffffff8105d178>] warn_slowpath_common+0x78/0xb0
[<ffffffff8105d1bf>] warn_slowpath_null+0xf/0x20
[<ffffffff81063f8b>] local_bh_enable_ip+0x7b/0xa0
[<ffffffff815121e4>] _spin_unlock_bh+0x14/0x20
[<ffffffffa034aea5>] ath_tx_node_cleanup+0x185/0x1b0 [ath9k]
[<ffffffffa0345597>] ath9k_sta_notify+0x57/0xb0 [ath9k]
[<ffffffffa02ac51a>] __sta_info_unlink+0x15a/0x260 [mac80211]
[<ffffffffa02ac658>] sta_info_unlink+0x38/0x60 [mac80211]
[<ffffffffa02b3fbe>] ieee80211_set_disassoc+0x1ae/0x210 [mac80211]
[<ffffffffa02b42d9>] ieee80211_mgd_deauth+0x109/0x110 [mac80211]
[<ffffffffa02ba409>] ieee80211_deauth+0x19/0x20 [mac80211]
[<ffffffffa028160e>] __cfg80211_mlme_deauth+0xee/0x130 [cfg80211]
[<ffffffff81118540>] ? init_object+0x50/0x90
[<ffffffffa0285429>] __cfg80211_disconnect+0x159/0x1d0 [cfg80211]
[<ffffffffa027125f>] cfg80211_netdev_notifier_call+0x10f/0x450 [cfg80211]
[<ffffffff81514ca7>] notifier_call_chain+0x47/0x90
[<ffffffff8107f501>] raw_notifier_call_chain+0x11/0x20
[<ffffffff81442d66>] call_netdevice_notifiers+0x16/0x20
[<ffffffff8144352d>] dev_close+0x4d/0xa0
[<ffffffff814439a8>] rollback_registered+0x48/0x120
[<ffffffff81443a9d>] unregister_netdevice+0x1d/0x70
[<ffffffffa02b6cc4>] ieee80211_remove_interfaces+0x84/0xc0 [mac80211]
[<ffffffffa02aa072>] ieee80211_unregister_hw+0x42/0xf0 [mac80211]
[<ffffffffa0347bde>] ath_detach+0x8e/0x180 [ath9k]
[<ffffffffa0347ce1>] ath_cleanup+0x11/0x50 [ath9k]
[<ffffffffa0351a2c>] ath_pci_remove+0x1c/0x20 [ath9k]
[<ffffffff8129d712>] pci_device_remove+0x32/0x60
[<ffffffff81332373>] __device_release_driver+0x53/0xb0
[<ffffffff81332498>] driver_detach+0xc8/0xd0
[<ffffffff81331405>] bus_remove_driver+0x85/0xe0
[<ffffffff81332a5a>] driver_unregister+0x5a/0x90
[<ffffffff8129da00>] pci_unregister_driver+0x40/0xb0
[<ffffffffa03518d0>] ath_pci_exit+0x10/0x20 [ath9k]
[<ffffffffa0353cd5>] ath9k_exit+0x9/0x2a [ath9k]
[<ffffffff81092838>] sys_delete_module+0x1a8/0x270
[<ffffffff8107ebe9>] ? up_read+0x9/0x10
[<ffffffff81011f82>] system_call_fastpath+0x16/0x1b
---[ end trace fad957019ffdd40b ]---
phy0: Removed STA 00:22:6b:56:fd:e8
phy0: Destroyed STA 00:22:6b:56:fd:e8
wlan31: deauthenticating from 00:22:6b:56:fd:e8 by local choice (reason=3)
ath9k 0000:16:00.0: PCI INT A disabled
The original lockdep fixed an issue where due to the new changes
the driver was not disabling the bottom halves but it is incorrect
to do this on the older kernels since IRQs are already disabled.
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 93a59d7527 upstream.
James Grossmann [1] reported that p54 spews out confusing
messages instead of preventing the mayhem from happening.
the reason is that "p54: generate channel list dynamically"
is not perfect. It didn't discard incomplete channel data
sets and therefore p54 advertised to support them as well.
[1]: http://marc.info/?l=linux-wireless&m=125699830215890
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: James Grossmann <cctsurf@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit a9e10fb9b1 upstream.
All the queues are awake and ready to use after loading firmware,
for firmware reload case, if any queues was stopped before
reload, mac80211 will wake those queues after restart hardware, so make
sure all the flag used to keep track of the queue status are
reset correctly.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 088ea189c4 upstream.
fix off by one error in the queue size check of p54_tx_qos_accounting_alloc()
Coverity CID: 13314
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit f5300e04df upstream.
A long time ago, a user reported several crashes due to
data corruptions which are likely the result of a
not-100%-supported, or faulty? PCI bridge.
( http://patchwork.kernel.org/patch/53004/ )
This patch fixes entry #1.
"1. p54p_check_rx_ring - skb_over_panic: Under a ping flood
or just left running for a bit would panic with a skb_over_panic."
As described in the mail: The invalid frame length causes
skb_put to bailout and trigger a crash.
Note:
Simply dropping the frame is problematic, because if its content
contains a tx feedback we would lose some portion of the device
memory space.... And the driver/mac80211 should handle all other
invalid data.
Reported-by: Quintin Pitts <geek4linux@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit bbcbb9ef97 upstream.
There is a problem if an "internal short scan" is in progress when a
mac80211 requested scan arrives. If this new scan request arrives within
the "next_scan_jiffies" period then driver will immediately return success
and complete the scan. The problem here is that the scan has not been
fully initialized at this time (is_internal_short_scan is still set to true
because of the currently running scan), which results in the scan
completion never to be sent to mac80211. At this time also, evan though the
internal short scan is still running the state (is_internal_short_scan)
will be set to false, so when the internal scan does complete then mac80211
will receive a scan completion.
Fix this by checking right away if a scan is in progress when a scan
request arrives from mac80211.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit dff010ac8e upstream.
Reset and clear all the tx queues when finished downloading runtime
uCode and ready to go into operation mode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 9e3bd91908 upstream.
This makes the b43 driver just automatically fall back to PIO mode when
DMA doesn't work.
The driver already told the user to do it, so rather than have the user
reload the module with a new flag, just make the driver do it
automatically. We keep the message as an indication that something is
wrong, but now just automatically fall back to the hopefully working PIO
case.
(Some post-2.6.33 merge fixups by Larry Finger <Larry.Finger@lwfinger.net>
and yours truly... -- JWL)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit b02914af4d upstream.
If userencounter the "Fatal DMA Problem" with a BCM43XX device, and
still wish to use b43 as the driver, their only option is to rebuild
the kernel with CONFIG_B43_FORCE_PIO. This patch removes this option and
allows PIO mode to be selected with a load-time parameter for the module.
Note that the configuration variable CONFIG_B43_PIO is also removed.
Once the DMA problem with the BCM4312 devices is solved, this patch will
likely be reverted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: John Daiker <daikerjohn@gmail.com>
Cc: maximilian attems <max@stro.at>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 214ac9a4ea upstream.
As shown in Kernel Bugzilla #14761, doing a controller restart after a
fatal DMA error does not accomplish anything other than consume the CPU
on an affected system. Accordingly, substitute a meaningful message for
the restart.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit ece6444c2f upstream.
For 4965, need to check it is valid qos frame before free, only valid
QoS frame has the tid used to free the packets.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 2d20c72c02 upstream.
An int urb is constructed but we fill it in with a bulk pipe type.
Commit f661c6f8c6 implemented a pipe type
check when CONFIG_USB_DEBUG is enabled. The check failed for all the ar9170
usb transfers and the driver could not configure the wifi dongle.
This went unnoticed until now because most people don't have
CONFIG_USB_DEBUG enabled.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 8e1a53c615 upstream.
IWL_RATE_COUNT is 13 and IWL_RATE_COUNT_LEGACY is 12.
IWL_RATE_COUNT_LEGACY is the right one here because iwl3945_rates
doesn't support 60M and also that's how "rates" is defined in
iwlcore_init_geos() from drivers/net/wireless/iwlwifi/iwl-core.c.
rates = kzalloc((sizeof(struct ieee80211_rate) * IWL_RATE_COUNT_LEGACY),
GFP_KERNEL);
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 96869a3939 upstream
The TKIP key update callback is called from the RX path, where the driver
mutex is already locked. This results in a circular locking bug.
Avoid this by removing the lock.
Johannes noted that there is a separate bug: The callback still breaks on SDIO
hardware, because SDIO hardware access needs to sleep, but we are not allowed
to sleep in the callback due to mac80211's RCU locking.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: kecsa@kutfo.hit.bme.hu
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 3f7c5c10e9 upstream.
The TIM timer interrupt is enabled even before the ACK of nullqos
is received which is unnecessary.
Also clean up the CONF_PS part of config callback properly for
better readability.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
