commit b16bef60a9 upstream.
The driver and its bindings, before commit 04f9f068a6 ("regulator:
s5m8767: Modify parsing method of the voltage table of buck2/3/4") were
requiring to provide at least one safe/default voltage for DVS registers
if DVS GPIO is not being enabled.
IOW, if s5m8767,pmic-buck2-uses-gpio-dvs is missing, the
s5m8767,pmic-buck2-dvs-voltage should still be present and contain one
voltage.
This requirement was coming from driver behavior matching this condition
(none of DVS GPIO is enabled): it was always initializing the DVS
selector pins to 0 and keeping the DVS enable setting at reset value
(enabled). Therefore if none of DVS GPIO is enabled in devicetree,
driver was configuring the first DVS voltage for buck[234].
Mentioned commit 04f9f068a6 ("regulator: s5m8767: Modify parsing
method of the voltage table of buck2/3/4") broke it because DVS voltage
won't be parsed from devicetree if DVS GPIO is not enabled. After the
change, driver will configure bucks to use the register reset value as
voltage which might have unpleasant effects.
Fix this by relaxing the bindings constrain: if DVS GPIO is not enabled
in devicetree (therefore DVS voltage is also not parsed), explicitly
disable it.
Cc: <stable@vger.kernel.org>
Fixes: 04f9f068a6 ("regulator: s5m8767: Modify parsing method of the voltage table of buck2/3/4")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Rob Herring <robh@kernel.org>
Message-Id: <20211008113723.134648-2-krzysztof.kozlowski@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ba546ebe0 ]
At the start of driver initialization, we do not know what bias
setting the bootloader has configured the system for and we only know
for certain the very first time we do a transition.
However, since the initial value of the comparison index is -EINVAL,
this negative value results in an array out of bound access on the
very first transition.
Since we don't know what the setting is, we just set the bias
configuration as there is nothing to compare against. This prevents
the array out of bound access.
NOTE: Even though we could use a more relaxed check of "< 0" the only
valid values(ignoring cosmic ray induced bitflips) are -EINVAL, 0+.
Fixes: 40b1936efe ("regulator: Introduce TI Adaptive Body Bias(ABB) on-chip LDO driver")
Link: https://lore.kernel.org/linux-mm/CA+G9fYuk4imvhyCN7D7T6PMDH6oNp6HDCRiTUKMQ6QXXjBa4ag@mail.gmail.com/
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20201118145009.10492-1-nm@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aea6cb9970 ]
When creating a new regulator its supply cannot create the sysfs link
because the device is not yet published. Remove early supply resolving
since it will be done later anyway. This makes the following error
disappear and the symlinks get created instead.
DCDC_REG1: supplied by VSYS
VSYS: could not add device link regulator.3 err -2
Note: It doesn't fix the problem for bypassed regulators, though.
Fixes: 45389c4752 ("regulator: core: Add early supply resolution for regulators")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/ba09e0a8617ffeeb25cb4affffe6f3149319cef8.1601155770.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8a039d377 ]
RK808 can leverage a couple of GPIOs to tweak the ramp rate during DVS
(Dynamic Voltage Scaling). These GPIOs are entirely optional but a
dev_warn() appeared when cleaning this driver to use a more up-to-date
gpiod API. At least reduce the log level to 'info' as it is totally
fine to not populate these GPIO on a hardware design.
This change is trivial but it is worth not polluting the logs during
bringup phase by having real warnings and errors sorted out
correctly.
Fixes: a13eaf02e2 ("regulator: rk808: make better use of the gpiod API")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191203164709.11127-1-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e69b394703 ]
selector 0xB (1011) should be 2.6V rather than 2.7V, fit ix.
Table 5-4. LDOA1 Output Voltage Options
VID Bits VOUT VID Bits VOUT VID Bits VOUT VID Bits VOUT
0000 1.35 0100 1.8 1000 2.3 1100 2.85
0001 1.5 0101 1.9 1001 2.4 1101 3.0
0010 1.6 0110 2.0 1010 2.5 1110 3.3
0011 1.7 0111 2.1 1011 2.6 1111 Not Used
Fixes: d2a2e729a6 ("regulator: tps65086: Add regulator driver for the TPS65086 PMIC")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c25d47888f ]
The wm831x_dcdc_ilim entries needs to be uA because it is used to compare
with min_uA and max_uA.
While at it also make the array const and change to use unsigned int.
Fixes: e4ee831f94 ("regulator: Add WM831x DC-DC buck convertor support")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5455c9159 ]
Fix off-by-one while iterating current_limits array.
The valid index should be 0 ~ n_current_limits -1.
Fixes: c90456e36d ("regulator: pv88090: new regulator driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c413f594c ]
Fix off-by-one while iterating current_limits array.
The valid index should be 0 ~ n_current_limits -1.
Fixes: 99cf3af5e2 ("regulator: pv88080: new regulator driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7cd415f875 ]
Fix off-by-one while iterating current_limits array.
The valid index should be 0 ~ n_current_limits -1.
Fixes: f307a7e9b7 ("regulator: pv88060: new regulator driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 99c4f70df3 upstream.
The USB regulator was removed for AB8500 in
commit 41a06aa738 ("regulator: ab8500: Remove USB regulator").
It was then added for AB8505 in
commit 547f384f33 ("regulator: ab8500: add support for ab8505").
However, there was never an entry added for it in
ab8505_regulator_match. This causes all regulators after it
to be initialized with the wrong device tree data, eventually
leading to an out-of-bounds array read.
Given that it is not used anywhere in the kernel, it seems
likely that similar arguments against supporting it exist for
AB8505 (it is controlled by hardware).
Therefore, simply remove it like for AB8500 instead of adding
an entry in ab8505_regulator_match.
Fixes: 547f384f33 ("regulator: ab8500: add support for ab8505")
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191106173125.14496-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8b8c8d69b1 which is
commit 55576cf185 upstream.
It's causing "odd" interactions with older kernels, so it probably isn't
a good idea to cause timing changes there. This has been reported to
cause oopses on Pixel devices.
Reported-by: Siddharth Kapoor <ksiddharth@google.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cd07e3701f ]
tps65910_reg_set_bits() may fail. The fix checks if it fails, and if so,
returns with its error code.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 966e927bf8 ]
If palmas_smps_read() fails, we should not use the read data in "reg"
which may contain random value. The fix inserts a check for the return
value of palmas_smps_read(): If it fails, we return the error code
upstream and stop using "reg".
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f64db54879 ]
ti_abb_wait_txdone() may return -ETIMEDOUT when ti_abb_check_txdone()
returns true in the latest iteration of the while loop because the timeout
value is abb->settling_time + 1. Similarly, ti_abb_clear_all_txdone() may
return -ETIMEDOUT when ti_abb_check_txdone() returns false in the latest
iteration of the while loop. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20190929095848.21960-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 55576cf185 upstream.
The kernel has no way of knowing when we have finished instantiating
drivers, between deferred probe and systems that build key drivers as
modules we might be doing this long after userspace has booted. This has
always been a bit of an issue with regulator_init_complete since it can
power off hardware that's not had it's driver loaded which can result in
user visible effects, the main case is powering off displays. Practically
speaking it's not been an issue in real systems since most systems that
use the regulator API are embedded and build in key drivers anyway but
with Arm laptops coming on the market it's becoming more of an issue so
let's do something about it.
In the absence of any better idea just defer the powering off for 30s
after late_initcall(), this is obviously a hack but it should mask the
issue for now and it's no more arbitrary than late_initcall() itself.
Ideally we'd have some heuristics to detect if we're on an affected
system and tune or skip the delay appropriately, and there may be some
need for a command line option to be added.
Link: https://lore.kernel.org/r/20190904124250.25844-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Lee Jones <lee.jones@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1e2cc8c5e0 ]
According to the datasheet https://www.ti.com/lit/ds/symlink/lm3632a.pdf
Table 20. VPOS Bias Register Field Descriptions VPOS[5:0]
Sets the Positive Display Bias (LDO) Voltage (50 mV per step)
000000: 4 V
000001: 4.05 V
000010: 4.1 V
....................
011101: 5.45 V
011110: 5.5 V (Default)
011111: 5.55 V
....................
100111: 5.95 V
101000: 6 V
Note: Codes 101001 to 111111 map to 6 V
The LM3632_LDO_VSEL_MAX should be 0b101000 (0x28), so the maximum voltage
can match the datasheet.
Fixes: 3a8d1a73a0 ("regulator: add LM363X driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20190626132632.32629-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 16da0eb5ab upstream.
On S2MPS11 device, the buck7 and buck8 regulator voltages start at 750
mV, not 600 mV. Using wrong minimal value caused shifting of these
regulator values by 150 mV (e.g. buck7 usually configured to v1.35 V was
reported as 1.2 V).
On most of the boards these regulators are left in default state so this
was only affecting reported voltage. However if any driver wanted to
change them, then effectively it would set voltage 150 mV higher than
intended.
Cc: <stable@vger.kernel.org>
Fixes: cb74685ecb ("regulator: s2mps11: Add samsung s2mps11 regulator driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f01a7beb67 ]
The act8600_sudcdc_voltage_ranges setting does not match the datasheet.
The problems in below entry:
REGULATOR_LINEAR_RANGE(19000000, 191, 255, 400000),
1. The off-by-one min_sel causes wrong volatage calculation.
The min_sel should be 192.
2. According to the datasheet[1] Table 7. (on page 43):
The selector 248 (0b11111000) ~ 255 (0b11111111) are 41.400V.
Also fix off-by-one for ACT8600_SUDCDC_VOLTAGE_NUM.
[1] https://active-semi.com/wp-content/uploads/ACT8600_Datasheet.pdf
Fixes: df3a950e4e ("regulator: act8865: Add act8600 support")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fb6de923ca upstream.
dev_set_drvdata() needs to be called before device_register()
exposes device to userspace. Otherwise kernel crashes after it
gets null pointer from dev_get_drvdata() when userspace tries
to access sysfs entries.
[Removed backtrace for length -- broonie]
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0b01fd3d40 ]
If is_enabled() is not defined, regulator core will assume
this regulator is already enabled, then it can NOT be really
enabled after disabled.
Based on Li Jun's patch from the NXP kernel tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fd08604555 ]
Commit 26988efe11 ("regulator: core: Allow to get voltage count and
list from parent") introduces the propagation of the parent voltage
count and list for regulators that don't provide this information
themselves. The goal is to support simple switch regulators, however as
a side effect normal continuous regulators can leak details of their
supplies and provide consumers with inconsistent information.
Limit the propagation of the voltage count and list to switch
regulators.
Fixes: 26988efe11 ("regulator: core: Allow to get voltage count and
list from parent")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc1111b885 upstream.
The device tree nodes all correctly describe the regulators as
syr827 or syr828, but the I2C device id is currently set to the
wildcard value of syr82x in the driver. This causes udev to fail
to match the driver module with the modalias data from sysfs.
Fix this by replacing the I2C device ids with ones that match the
device tree descriptions, with syr827 and syr828. Tested on
Firefly rk3288 board. The syr82x id was not used anywhere.
Fixes: e80c47bd73 (regulator: fan53555: Export I2C module alias information)
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3827b64dba ]
After commit 66d228a2bf ("regulator: core: Don't use regulators as
supplies until the parent is bound"), input supplies aren't resolved
if the input supplies parent device has not been bound. This prevent
regulators to hold an invalid reference if its supply parent device
driver probe is deferred.
But this causes issues on some boards where a PMIC's regulator use as
input supply a regulator from another PMIC whose driver is registered
after the driver for the former.
In this case the regulators for the first PMIC will fail to resolve
input supplies on regulators registration (since the other PMIC wasn't
probed yet). And when the core attempts to resolve again latter when
the other PMIC registers its own regulators, it will fail again since
the parent device isn't bound yet.
This will cause some parent supplies to never be resolved and wrongly
be disabled on boot due taking them as unused.
To solve this problem, also attempt to resolve the pending regulators
input supplies before disabling the unused regulators.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6308f1787f upstream.
When we check for additional DT properties in the current node we
use the device_node passed in with the configuration data, this
will not point to the correct DT node, use the one passed in
for this purpose.
Fixes: d2a2e729a6 ("regulator: tps65086: Add regulator driver for the TPS65086 PMIC")
Reported-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c47f7c316 upstream.
The three load switches are called SWA1, SWB1, and SWB2. The
node names describing properties for these are expected to be
the same, but due to a typo they are not. Fix this here.
Fixes: d2a2e729a6 ("regulator: tps65086: Add regulator driver for the TPS65086 PMIC")
Reported-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c90722b54a upstream.
Commit 43530b69d7 ("regulator: Use
regmap_read/write(), regmap_update_bits functions directly") intended
to replace working inline helper functions with standard regmap
calls. However, it also inverted the set/clear logic of the "CORE ADJ
Allowed" bit. That patch was clearly never tested, since without that
bit cleared, the core VDCDC1 voltage output does not react to I2C
configuration changes.
This patch fixes the issue by clearing the bit as in the original,
correct implementation. Note for stable back porting that, due to
subsequent driver churn, this patch will not apply on every kernel
version.
Fixes: 43530b69d7 ("regulator: Use regmap_read/write(), regmap_update_bits functions directly")
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e42a46b6f5 upstream.
It is allowed to call regulator_get with a NULL dev argument
(_regulator_get explicitly checks for it) but this causes an error later
when printing /sys/kernel/debug/regulator_summary.
Fix this by explicitly handling "deviceless" consumers in the debugfs code.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0e287a401 upstream.
A typo or copy-paste bug means that the register access intended for
regulator dcdce goes to dcdcb instead. This patch corrects it.
Fixes: 2ca342d391 (regulator: axp20x: Support AXP806 variant)
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85b037442e upstream.
The handling of bypass_val_on that was added in
regulator_get_bypass_regmap is done unconditionally however
several drivers don't define a value for bypass_val_on. This
results in those drivers reporting bypass being enabled when
it is not. In regulator_set_bypass_regmap we use bypass_mask
if bypass_val_on is zero. This patch adds similar handling in
regulator_get_bypass_regmap.
Fixes: commit dd1a571dae ("regulator: helpers: Ensure bypass register field matches ON value")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 618c808968 upstream.
The maximum supported voltage for ldo_io# is 3.3V, but on cold boot
the selector comes up at 0x1f, which maps to 3.8V. This was previously
corrected by Allwinner's U-boot, which set all regulators on the PMICs
to some pre-configured voltage. With recent progress in U-boot SPL
support, this is no longer the case. In any case we should handle
this quirk in the kernel driver as well.
This invalid setting causes _regulator_get_voltage() to fail with -EINVAL
which causes regulator registration to fail when constrains are used:
[ 1.054181] vcc-pg: failed to get the current voltage(-22)
[ 1.059670] axp20x-regulator axp20x-regulator.0: Failed to register ldo_io0
[ 1.069749] axp20x-regulator: probe of axp20x-regulator.0 failed with error -22
This commits makes the axp20x regulator driver accept the 0x1f register
value, fixing this.
The datasheet does not guarantee reliable operation above 3.3V, so on
boards where this regulator is used the regulator-max-microvolt setting
must be 3.3V or less.
This is essentially the same as the commit f40d4896bf ("regulator:
axp20x: Fix axp22x ldo_io registration error on cold boot") for AXP22x
PMICs.
Fixes: a51f9f4622 ("regulator: axp20x: support AXP809 variant")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8ca5bd158 upstream.
The BUCK regulators 3, 4, and 5 also have a 10mV step mode,
adjust the tables and logic to reflect the data-sheet for
these regulators.
fixes: d2a2e729a6 ("regulator: tps65086: Add regulator driver for the TPS65086 PMIC")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 295070e9aa upstream.
The regulator has never been properly enabled, it has been
dormant all the time. It's strange that MMC was working
at all, but it likely worked by the signals going through
the levelshifter and reaching the card anyways.
Fixes: 3615a34ea1 ("regulator: add STw481x VMMC driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73e705bf81 ("regulator: core: Add set_voltage_time op")
introduced a new rdev_warn() if the ramp_delay is 0.
Apparently, on omap3/twl4030 platforms with dynamic voltage
management this results in non-ending spurious messages like
[ 511.143066] VDD1: ramp_delay not set
[ 511.662322] VDD1: ramp_delay not set
[ 513.903625] VDD1: ramp_delay not set
[ 514.222198] VDD1: ramp_delay not set
[ 517.062835] VDD1: ramp_delay not set
[ 517.382568] VDD1: ramp_delay not set
[ 520.142791] VDD1: ramp_delay not set
[ 520.502593] VDD1: ramp_delay not set
[ 523.062896] VDD1: ramp_delay not set
[ 523.362701] VDD1: ramp_delay not set
[ 526.143035] VDD1: ramp_delay not set
I have observed this on GTA04 while it is reported to occur on
N900 as well: https://bugzilla.kernel.org/show_bug.cgi?id=178371
This patch makes the warning appear only in debugging mode.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull thermal managament updates from Zhang Rui:
- Enhance thermal "userspace" governor to export the reason when a
thermal event is triggered and delivered to user space. From Srinivas
Pandruvada
- Introduce a single TSENS thermal driver for the different versions of
the TSENS IP that exist, on different qcom msm/apq SoCs'. Support for
msm8916, msm8960, msm8974 and msm8996 families is also added. From
Rajendra Nayak
- Introduce hardware-tracked trip points support to the device tree
thermal sensor framework. The framework supports an arbitrary number
of trip points. Whenever the current temperature is changed, the trip
points immediately below and above the current temperature are found,
driver callback is invoked to program the hardware to get notified
when either of the two trip points are triggered. Hardware-tracked
trip points support for rockchip thermal driver is also added at the
same time. From Sascha Hauer, Caesar Wang
- Introduce a new thermal driver, which enables TMU (Thermal Monitor
Unit) on QorIQ platform. From Jia Hongtao
- Introduce a new thermal driver for Maxim MAX77620. From Laxman
Dewangan
- Introduce a new thermal driver for Intel platforms using WhiskeyCove
PMIC. From Bin Gao
- Add mt2701 chip support to MTK thermal driver. From Dawei Chien
- Enhance Tegra thermal driver to enable soctherm node and set
"critical", "hot" trips, for Tegra124, Tegra132, Tegra210. From Wei
Ni
- Add resume support for tango thermal driver. From Marc Gonzalez
- several small fixes and improvements for rockchip, qcom, imx, rcar,
mtk thermal drivers and thermal core code. From Caesar Wang, Keerthy,
Rocky Hao, Wei Yongjun, Peter Robinson, Bui Duc Phuc, Axel Lin, Hugh
Kang
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (48 commits)
thermal: int3403: Process trip change notification
thermal: int340x: New Interface to read trip and notify
thermal: user_space gov: Add additional information in uevent
thermal: Enhance thermal_zone_device_update for events
arm64: tegra: set hot trips for Tegra210
arm64: tegra: set critical trips for Tegra210
arm64: tegra: add soctherm node for Tegra210
arm64: tegra: set hot trips for Tegra132
arm64: tegra: set critical trips for Tegra132
arm64: tegra: use tegra132-soctherm for Tegra132
arm: tegra: set hot trips for Tegra124
arm: tegra: set critical trips for Tegra124
thermal: tegra: add hw-throttle for Tegra132
thermal: tegra: add hw-throttle function
of: Add bindings of hw throttle for Tegra soctherm
thermal: mtk_thermal: Check return value of devm_thermal_zone_of_sensor_register
thermal: Add Mediatek thermal driver for mt2701.
dt-bindings: thermal: Add binding document for Mediatek thermal controller
thermal: max77620: Add thermal driver for reporting junction temp
thermal: max77620: Add DT binding doc for thermal driver
...
