commit 860dafa902 upstream.
Restore the original intent of the VT_RESIZEX ioctl's `v_clin' parameter
which is the number of pixel rows per character (cell) rather than the
height of the font used.
For framebuffer devices the two values are always the same, because the
former is inferred from the latter one. For VGA used as a true text
mode device these two parameters are independent from each other: the
number of pixel rows per character is set in the CRT controller, while
font height is in fact hardwired to 32 pixel rows and fonts of heights
below that value are handled by padding their data with blanks when
loaded to hardware for use by the character generator. One can change
the setting in the CRT controller and it will update the screen contents
accordingly regardless of the font loaded.
The `v_clin' parameter is used by the `vgacon' driver to set the height
of the character cell and then the cursor position within. Make the
parameter explicit then, by defining a new `vc_cell_height' struct
member of `vc_data', set it instead of `vc_font.height' from `v_clin' in
the VT_RESIZEX ioctl, and then use it throughout the `vgacon' driver
except where actual font data is accessed which as noted above is
independent from the CRTC setting.
This way the framebuffer console driver is free to ignore the `v_clin'
parameter as irrelevant, as it always should have, avoiding any issues
attempts to give the parameter a meaning there could have caused, such
as one that has led to commit 988d076336 ("vt_ioctl: make VT_RESIZEX
behave like VT_RESIZE"):
"syzbot is reporting UAF/OOB read at bit_putcs()/soft_cursor() [1][2],
for vt_resizex() from ioctl(VT_RESIZEX) allows setting font height
larger than actual font height calculated by con_font_set() from
ioctl(PIO_FONT). Since fbcon_set_font() from con_font_set() allocates
minimal amount of memory based on actual font height calculated by
con_font_set(), use of vt_resizex() can cause UAF/OOB read for font
data."
The problem first appeared around Linux 2.5.66 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit 9736a3546de7 ("Merge with Linux 2.5.66."), where VT_RESIZEX
code in `vt_ioctl' was updated as follows:
if (clin)
- video_font_height = clin;
+ vc->vc_font.height = clin;
making the parameter apply to framebuffer devices as well, perhaps due
to the use of "font" in the name of the original `video_font_height'
variable. Use "cell" in the new struct member then to avoid ambiguity.
References:
[1] https://syzkaller.appspot.com/bug?id=32577e96d88447ded2d3b76d71254fb855245837
[2] https://syzkaller.appspot.com/bug?id=6b8355d27b2b94fb5cedf4655e3a59162d9e48e3
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4d0ad57b3 upstream.
Fix an issue with VGA console font size changes made after the initial
video text mode has been changed with a user tool like `svgatextmode'
calling the VT_RESIZEX ioctl. As it stands in that case the original
screen geometry continues being used to validate further VT resizing.
Consequently when the video adapter is firstly reprogrammed from the
original say 80x25 text mode using a 9x16 character cell (720x400 pixel
resolution) to say 80x37 text mode and the same character cell (720x592
pixel resolution), and secondly the CRTC character cell updated to 9x8
(by loading a suitable font with the KD_FONT_OP_SET request of the
KDFONTOP ioctl), the VT geometry does not get further updated from 80x37
and only upper half of the screen is used for the VT, with the lower
half showing rubbish corresponding to whatever happens to be there in
the video memory that maps to that part of the screen. Of course the
proportions change according to text mode geometries and font sizes
chosen.
Address the problem then, by updating the text mode geometry defaults
rather than checking against them whenever the VT is resized via a user
ioctl.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: e400b6ec4e ("vt/vgacon: Check if screen resize request comes from userspace")
Cc: stable@vger.kernel.org # v2.6.24+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 973c096f6a upstream.
Yunhai Zhang recently fixed a VGA software scrollback bug in commit
ebfdfeeae8 ("vgacon: Fix for missing check in scrollback handling"),
but that then made people look more closely at some of this code, and
there were more problems on the vgacon side, but also the fbcon software
scrollback.
We don't really have anybody who maintains this code - probably because
nobody actually _uses_ it any more. Sure, people still use both VGA and
the framebuffer consoles, but they are no longer the main user
interfaces to the kernel, and haven't been for decades, so these kinds
of extra features end up bitrotting and not really being used.
So rather than try to maintain a likely unused set of code, I'll just
aggressively remove it, and see if anybody even notices. Maybe there
are people who haven't jumped on the whole GUI badnwagon yet, and think
it's just a fad. And maybe those people use the scrollback code.
If that turns out to be the case, we can resurrect this again, once
we've found the sucker^Wmaintainer for it who actually uses it.
Reported-by: NopNop Nop <nopitydays@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Cc: 张云海 <zhangyunhai@nsfocus.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Willy Tarreau <w@1wt.eu>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50145474f6 upstream.
This (and the VGA soft scrollback) turns out to have various nasty small
special cases that nobody really is willing to fight. The soft
scrollback code was really useful a few decades ago when you typically
used the console interactively as the main way to interact with the
machine, but that just isn't the case any more.
So it's not worth dragging along.
Tested-by: Yuan Ming <yuanmingbuaa@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebfdfeeae8 upstream.
vgacon_scrollback_update() always leaves enbough room in the scrollback
buffer for the next call, but if the console size changed that room
might not actually be enough, and so we need to re-check.
The check should be in the loop since vgacon_scrollback_cur->tail is
updated in the loop and count may be more than 1 when triggered by CSI M,
as Jiri's PoC:
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <sys/ioctl.h>
#include <fcntl.h>
int main(int argc, char** argv)
{
int fd = open("/dev/tty1", O_RDWR);
unsigned short size[3] = {25, 200, 0};
ioctl(fd, 0x5609, size); // VT_RESIZE
write(fd, "\e[1;1H", 6);
for (int i = 0; i < 30; i++)
write(fd, "\e[10M", 5);
}
It leads to various crashes as vgacon_scrollback_update writes out of
the buffer:
BUG: unable to handle page fault for address: ffffc900001752a0
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
RIP: 0010:mutex_unlock+0x13/0x30
...
Call Trace:
n_tty_write+0x1a0/0x4d0
tty_write+0x1a0/0x2e0
Or to KASAN reports:
BUG: KASAN: slab-out-of-bounds in vgacon_scroll+0x57a/0x8ed
This fixes CVE-2020-14331.
Reported-by: 张云海 <zhangyunhai@nsfocus.com>
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Reported-by: Kyungtae Kim <kt0755@gmail.com>
Fixes: 15bdab959c ([PATCH] vgacon: Add support for soft scrollback)
Cc: stable@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Solar Designer <solar@openwall.com>
Cc: "Srivatsa S. Bhat" <srivatsa@csail.mit.edu>
Cc: Anthony Liguori <aliguori@amazon.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Yunhai Zhang <zhangyunhai@nsfocus.com>
Link: https://lore.kernel.org/r/9fb43895-ca91-9b07-ebfd-808cf854ca95@nsfocus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 033724d686 ]
syzbot is reporting general protection fault in bitfill_aligned() [1]
caused by integer underflow in bit_clear_margins(). The cause of this
problem is when and how do_vc_resize() updates vc->vc_{cols,rows}.
If vc_do_resize() fails (e.g. kzalloc() fails) when var.xres or var.yres
is going to shrink, vc->vc_{cols,rows} will not be updated. This allows
bit_clear_margins() to see info->var.xres < (vc->vc_cols * cw) or
info->var.yres < (vc->vc_rows * ch). Unexpectedly large rw or bh will
try to overrun the __iomem region and causes general protection fault.
Also, vc_resize(vc, 0, 0) does not set vc->vc_{cols,rows} = 0 due to
new_cols = (cols ? cols : vc->vc_cols);
new_rows = (lines ? lines : vc->vc_rows);
exception. Since cols and lines are calculated as
cols = FBCON_SWAP(ops->rotate, info->var.xres, info->var.yres);
rows = FBCON_SWAP(ops->rotate, info->var.yres, info->var.xres);
cols /= vc->vc_font.width;
rows /= vc->vc_font.height;
vc_resize(vc, cols, rows);
in fbcon_modechanged(), var.xres < vc->vc_font.width makes cols = 0
and var.yres < vc->vc_font.height makes rows = 0. This means that
const int fd = open("/dev/fb0", O_ACCMODE);
struct fb_var_screeninfo var = { };
ioctl(fd, FBIOGET_VSCREENINFO, &var);
var.xres = var.yres = 1;
ioctl(fd, FBIOPUT_VSCREENINFO, &var);
easily reproduces integer underflow bug explained above.
Of course, callers of vc_resize() are not handling vc_do_resize() failure
is bad. But we can't avoid vc_resize(vc, 0, 0) which returns 0. Therefore,
as a band-aid workaround, this patch checks integer underflow in
"struct fbcon_ops"->clear_margins call, assuming that
vc->vc_cols * vc->vc_font.width and vc->vc_rows * vc->vc_font.heigh do not
cause integer overflow.
[1] https://syzkaller.appspot.com/bug?id=a565882df74fa76f10d3a6fec4be31098dbb37c6
Reported-and-tested-by: syzbot <syzbot+e5fd3e65515b48c02a30@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200715015102.3814-1-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 513dc792d6 upstream.
When syzkaller tests, there is a UAF:
BUG: KASan: use after free in vgacon_invert_region+0x9d/0x110 at addr
ffff880000100000
Read of size 2 by task syz-executor.1/16489
page:ffffea0000004000 count:0 mapcount:-127 mapping: (null)
index:0x0
page flags: 0xfffff00000000()
page dumped because: kasan: bad access detected
CPU: 1 PID: 16489 Comm: syz-executor.1 Not tainted
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014
Call Trace:
[<ffffffffb119f309>] dump_stack+0x1e/0x20
[<ffffffffb04af957>] kasan_report+0x577/0x950
[<ffffffffb04ae652>] __asan_load2+0x62/0x80
[<ffffffffb090f26d>] vgacon_invert_region+0x9d/0x110
[<ffffffffb0a39d95>] invert_screen+0xe5/0x470
[<ffffffffb0a21dcb>] set_selection+0x44b/0x12f0
[<ffffffffb0a3bfae>] tioclinux+0xee/0x490
[<ffffffffb0a1d114>] vt_ioctl+0xff4/0x2670
[<ffffffffb0a0089a>] tty_ioctl+0x46a/0x1a10
[<ffffffffb052db3d>] do_vfs_ioctl+0x5bd/0xc40
[<ffffffffb052e2f2>] SyS_ioctl+0x132/0x170
[<ffffffffb11c9b1b>] system_call_fastpath+0x22/0x27
Memory state around the buggy address:
ffff8800000fff00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00
ffff8800000fff80: 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00
>ffff880000100000: ff ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff
It can be reproduce in the linux mainline by the program:
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <fcntl.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <sys/ioctl.h>
#include <linux/vt.h>
struct tiocl_selection {
unsigned short xs; /* X start */
unsigned short ys; /* Y start */
unsigned short xe; /* X end */
unsigned short ye; /* Y end */
unsigned short sel_mode; /* selection mode */
};
#define TIOCL_SETSEL 2
struct tiocl {
unsigned char type;
unsigned char pad;
struct tiocl_selection sel;
};
int main()
{
int fd = 0;
const char *dev = "/dev/char/4:1";
struct vt_consize v = {0};
struct tiocl tioc = {0};
fd = open(dev, O_RDWR, 0);
v.v_rows = 3346;
ioctl(fd, VT_RESIZEX, &v);
tioc.type = TIOCL_SETSEL;
ioctl(fd, TIOCLINUX, &tioc);
return 0;
}
When resize the screen, update the 'vc->vc_size_row' to the new_row_size,
but when 'set_origin' in 'vgacon_set_origin', vgacon use 'vga_vram_base'
for 'vc_origin' and 'vc_visible_origin', not 'vc_screenbuf'. It maybe
smaller than 'vc_screenbuf'. When TIOCLINUX, use the new_row_size to calc
the offset, it maybe larger than the vga_vram_size in vgacon driver, then
bad access.
Also, if set an larger screenbuf firstly, then set an more larger
screenbuf, when copy old_origin to new_origin, a bad access may happen.
So, If the screen size larger than vga_vram, resize screen should be
failed. This alse fix CVE-2020-8649 and CVE-2020-8647.
Linus pointed out that overflow checking seems absent. We're saved by
the existing bounds checks in vc_do_resize() with rather strict
limits:
if (cols > VC_RESIZE_MAXCOL || lines > VC_RESIZE_MAXROW)
return -EINVAL;
Fixes: 0aec4867dc ("[PATCH] SVGATextMode fix")
Reference: CVE-2020-8647 and CVE-2020-8649
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
[danvet: augment commit message to point out overflow safety]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304022429.37738-1-zhangxiaoxu5@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2122b40580 ]
When unregistering fbdev using unregister_framebuffer(), any bound
console will unbind automatically. This is working fine if this is the
only framebuffer, resulting in a switch to the dummy console. However if
there is a fb0 and I unregister fb1 having a bound console, I eventually
get a crash. The fastest way for me to trigger the crash is to do a
reboot, resulting in this splat:
[ 76.478825] WARNING: CPU: 0 PID: 527 at linux/kernel/workqueue.c:1442 __queue_work+0x2d4/0x41c
[ 76.478849] Modules linked in: raspberrypi_hwmon gpio_backlight backlight bcm2835_rng rng_core [last unloaded: tinydrm]
[ 76.478916] CPU: 0 PID: 527 Comm: systemd-udevd Not tainted 4.20.0-rc4+ #4
[ 76.478933] Hardware name: BCM2835
[ 76.478949] Backtrace:
[ 76.478995] [<c010d388>] (dump_backtrace) from [<c010d670>] (show_stack+0x20/0x24)
[ 76.479022] r6:00000000 r5:c0bc73be r4:00000000 r3:6fb5bf81
[ 76.479060] [<c010d650>] (show_stack) from [<c08e82f4>] (dump_stack+0x20/0x28)
[ 76.479102] [<c08e82d4>] (dump_stack) from [<c0120070>] (__warn+0xec/0x12c)
[ 76.479134] [<c011ff84>] (__warn) from [<c01201e4>] (warn_slowpath_null+0x4c/0x58)
[ 76.479165] r9:c0eb6944 r8:00000001 r7:c0e927f8 r6:c0bc73be r5:000005a2 r4:c0139e84
[ 76.479197] [<c0120198>] (warn_slowpath_null) from [<c0139e84>] (__queue_work+0x2d4/0x41c)
[ 76.479222] r6:d7666a00 r5:c0e918ee r4:dbc4e700
[ 76.479251] [<c0139bb0>] (__queue_work) from [<c013a02c>] (queue_work_on+0x60/0x88)
[ 76.479281] r10:c0496bf8 r9:00000100 r8:c0e92ae0 r7:00000001 r6:d9403700 r5:d7666a00
[ 76.479298] r4:20000113
[ 76.479348] [<c0139fcc>] (queue_work_on) from [<c0496c28>] (cursor_timer_handler+0x30/0x54)
[ 76.479374] r7:d8a8fabc r6:c0e08088 r5:d8afdc5c r4:d8a8fabc
[ 76.479413] [<c0496bf8>] (cursor_timer_handler) from [<c0178744>] (call_timer_fn+0x100/0x230)
[ 76.479435] r4:c0e9192f r3:d758a340
[ 76.479465] [<c0178644>] (call_timer_fn) from [<c0178980>] (expire_timers+0x10c/0x12c)
[ 76.479495] r10:40000000 r9:c0e9192f r8:c0e92ae0 r7:d8afdccc r6:c0e19280 r5:c0496bf8
[ 76.479513] r4:d8a8fabc
[ 76.479541] [<c0178874>] (expire_timers) from [<c0179630>] (run_timer_softirq+0xa8/0x184)
[ 76.479570] r9:00000001 r8:c0e19280 r7:00000000 r6:c0e08088 r5:c0e1a3e0 r4:c0e19280
[ 76.479603] [<c0179588>] (run_timer_softirq) from [<c0102404>] (__do_softirq+0x1ac/0x3fc)
[ 76.479632] r10:c0e91680 r9:d8afc020 r8:0000000a r7:00000100 r6:00000001 r5:00000002
[ 76.479650] r4:c0eb65ec
[ 76.479686] [<c0102258>] (__do_softirq) from [<c0124d10>] (irq_exit+0xe8/0x168)
[ 76.479716] r10:d8d1a9b0 r9:d8afc000 r8:00000001 r7:d949c000 r6:00000000 r5:c0e8b3f0
[ 76.479734] r4:00000000
[ 76.479764] [<c0124c28>] (irq_exit) from [<c016b72c>] (__handle_domain_irq+0x94/0xb0)
[ 76.479793] [<c016b698>] (__handle_domain_irq) from [<c01021dc>] (bcm2835_handle_irq+0x3c/0x48)
[ 76.479823] r8:d8afdebc r7:d8afddfc r6:ffffffff r5:c0e089f8 r4:d8afddc8 r3:d8afddc8
[ 76.479851] [<c01021a0>] (bcm2835_handle_irq) from [<c01019f0>] (__irq_svc+0x70/0x98)
The problem is in the console rebinding in fbcon_fb_unbind(). It uses the
virtual console index as the new framebuffer index to bind the console(s)
to. The correct way is to use the con2fb_map lookup table to find the
framebuffer index.
Fixes: cfafca8067 ("fbdev: fbcon: console unregistration from unregister_framebuffer")
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Changes in 4.9.90
tpm: fix potential buffer overruns caused by bit glitches on the bus
ASoC: rsnd: check src mod pointer for rsnd_mod_id()
SMB3: Validate negotiate request must always be signed
CIFS: Enable encryption during session setup phase
staging: android: ashmem: Fix possible deadlock in ashmem_ioctl
Revert "led: core: Fix brightness setting when setting delay_off=0"
led: core: Clear LED_BLINK_SW flag in led_blink_set()
platform/x86: asus-nb-wmi: Add wapf4 quirk for the X302UA
bonding: handle link transition from FAIL to UP correctly
regulator: anatop: set default voltage selector for pcie
power: supply: bq24190_charger: Limit over/under voltage fault logging
x86: i8259: export legacy_pic symbol
rtc: cmos: Do not assume irq 8 for rtc when there are no legacy irqs
Input: ar1021_i2c - fix too long name in driver's device table
time: Change posix clocks ops interfaces to use timespec64
ACPI/processor: Fix error handling in __acpi_processor_start()
ACPI/processor: Replace racy task affinity logic
cpufreq/sh: Replace racy task affinity logic
genirq: Use irqd_get_trigger_type to compare the trigger type for shared IRQs
i2c: i2c-scmi: add a MS HID
net: ipv6: send unsolicited NA on admin up
media/dvb-core: Race condition when writing to CAM
btrfs: fix a bogus warning when converting only data or metadata
ASoC: Intel: Atom: update Thinkpad 10 quirk
tools/testing/nvdimm: fix nfit_test shutdown crash
spi: dw: Disable clock after unregistering the host
powerpc/64s: Remove SAO feature from Power9 DD1
ath: Fix updating radar flags for coutry code India
clk: ns2: Correct SDIO bits
iwlwifi: split the handler and the wake parts of the notification infra
iwlwifi: a000: fix memory offsets and lengths
scsi: virtio_scsi: Always try to read VPD pages
KVM: PPC: Book3S PR: Exit KVM on failed mapping
mwifiex: don't leak 'chan_stats' on reset
x86/reboot: Turn off KVM when halting a CPU
ARM: 8668/1: ftrace: Fix dynamic ftrace with DEBUG_RODATA and !FRAME_POINTER
irqchip/mips-gic: Separate IPI reservation & usage tracking
iommu/omap: Register driver before setting IOMMU ops
md/raid10: wait up frozen array in handle_write_completed
NFS: Fix missing pg_cleanup after nfs_pageio_cond_complete()
tcp: remove poll() flakes with FastOpen
e1000e: fix timing for 82579 Gigabit Ethernet controller
ALSA: hda - Fix headset microphone detection for ASUS N551 and N751
IB/ipoib: Fix deadlock between ipoib_stop and mcast join flow
IB/ipoib: Update broadcast object if PKey value was changed in index 0
HSI: ssi_protocol: double free in ssip_pn_xmit()
IB/mlx4: Take write semaphore when changing the vma struct
IB/mlx4: Change vma from shared to private
IB/mlx5: Take write semaphore when changing the vma struct
IB/mlx5: Change vma from shared to private
IB/mlx5: Set correct SL in completion for RoCE
ASoC: Intel: Skylake: Uninitialized variable in probe_codec()
ibmvnic: Disable irq prior to close
netvsc: Deal with rescinded channels correctly
Fix driver usage of 128B WQEs when WQ_CREATE is V1.
Fix Express lane queue creation.
gpio: gpio-wcove: fix irq pending status bit width
netfilter: xt_CT: fix refcnt leak on error path
openvswitch: Delete conntrack entry clashing with an expectation.
netfilter: nf_ct_helper: permit cthelpers with different names via nfnetlink
mmc: host: omap_hsmmc: checking for NULL instead of IS_ERR()
tipc: check return value of nlmsg_new
wan: pc300too: abort path on failure
qlcnic: fix unchecked return value
netfilter: nft_dynset: continue to next expr if _OP_ADD succeeded
platform/x86: intel-vbtn: add volume up and down
scsi: mac_esp: Replace bogus memory barrier with spinlock
infiniband/uverbs: Fix integer overflows
pNFS: Fix use after free issues in pnfs_do_read()
xprtrdma: Cancel refresh worker during buffer shutdown
NFS: don't try to cross a mountpount when there isn't one there.
iio: st_pressure: st_accel: Initialise sensor platform data properly
mt7601u: check return value of alloc_skb
libertas: check return value of alloc_workqueue
rndis_wlan: add return value validation
Btrfs: fix incorrect space accounting after failure to insert inline extent
Btrfs: send, fix file hole not being preserved due to inline extent
Btrfs: fix extent map leak during fallocate error path
orangefs: do not wait for timeout if umounting
mac80211: don't parse encrypted management frames in ieee80211_frame_acked
ACPICA: iasl: Fix IORT SMMU GSI disassembling
iio: hid-sensor: fix return of -EINVAL on invalid values in ret or value
dt-bindings: mfd: axp20x: Add "xpowers,master-mode" property for AXP806 PMICs
mfd: palmas: Reset the POWERHOLD mux during power off
mtip32xx: use runtime tag to initialize command header
x86/KASLR: Fix kexec kernel boot crash when KASLR randomization fails
gpio: gpio-wcove: fix GPIO IRQ status mask
staging: unisys: visorhba: fix s-Par to boot with option CONFIG_VMAP_STACK set to y
staging: wilc1000: fix unchecked return value
ipvs: explicitly forbid ipv6 service/dest creation if ipv6 mod is disabled
mac80211: Fix possible sband related NULL pointer de-reference
mmc: sdhci-of-esdhc: limit SD clock for ls1012a/ls1046a
netfilter: x_tables: unlock on error in xt_find_table_lock()
ARM: DRA7: clockdomain: Change the CLKTRCTRL of CM_PCIE_CLKSTCTRL to SW_WKUP
IB/rdmavt: restore IRQs on error path in rvt_create_ah()
IB/hfi1: Fix softlockup issue
platform/x86: asus-wmi: try to set als by default
ipmi/watchdog: fix wdog hang on panic waiting for ipmi response
ACPI / PMIC: xpower: Fix power_table addresses
drm/amdgpu: fix gpu reset crash
drm/nouveau/kms: Increase max retries in scanout position queries.
jbd2: Fix lockdep splat with generic/270 test
ixgbevf: fix size of queue stats length
net: ethernet: ucc_geth: fix MEM_PART_MURAM mode
soc/fsl/qe: round brg_freq to 1kHz granularity
Bluetooth: hci_ldisc: Add protocol check to hci_uart_dequeue()
Bluetooth: hci_ldisc: Add protocol check to hci_uart_tx_wakeup()
vxlan: correctly handle ipv6.disable module parameter
qed: Unlock on error in qed_vf_pf_acquire()
bnx2x: Align RX buffers
power: supply: bq24190_charger: Add disable-reset device-property
power: supply: isp1704: Fix unchecked return value of devm_kzalloc
power: supply: pda_power: move from timer to delayed_work
Input: twl4030-pwrbutton - use correct device for irq request
IB/rxe: Don't clamp residual length to mtu
md/raid10: skip spare disk as 'first' disk
ACPI / power: Delay turning off unused power resources after suspend
ia64: fix module loading for gcc-5.4
tcm_fileio: Prevent information leak for short reads
x86/xen: split xen_smp_prepare_boot_cpu()
video: fbdev: udlfb: Fix buffer on stack
sm501fb: don't return zero on failure path in sm501fb_start()
pNFS: Fix a deadlock when coalescing writes and returning the layout
net: hns: fix ethtool_get_strings overflow in hns driver
cifs: small underflow in cnvrtDosUnixTm()
mm: fix check for reclaimable pages in PF_MEMALLOC reclaim throttling
mm, vmstat: suppress pcp stats for unpopulated zones in zoneinfo
mm: hwpoison: call shake_page() after try_to_unmap() for mlocked page
rtc: ds1374: wdt: Fix issue with timeout scaling from secs to wdt ticks
rtc: ds1374: wdt: Fix stop/start ioctl always returning -EINVAL
ath10k: fix out of bounds access to local buffer
perf tests kmod-path: Don't fail if compressed modules aren't supported
block/mq: Cure cpu hotplug lock inversion
Bluetooth: hci_qca: Avoid setup failure on missing rampatch
Bluetooth: btqcomsmd: Fix skb double free corruption
media: c8sectpfe: fix potential NULL pointer dereference in c8sectpfe_timer_interrupt
drm/msm: fix leak in failed get_pages
RDMA/iwpm: Fix uninitialized error code in iwpm_send_mapinfo()
rtlwifi: rtl_pci: Fix the bug when inactiveps is enabled.
media: bt8xx: Fix err 'bt878_probe()'
ath10k: handling qos at STA side based on AP WMM enable/disable
media: [RESEND] media: dvb-frontends: Add delay to Si2168 restart
qmi_wwan: set FLAG_SEND_ZLP to avoid network initiated disconnect
serial: 8250_dw: Disable clock on error
cros_ec: fix nul-termination for firmware build info
watchdog: Fix potential kref imbalance when opening watchdog
platform/chrome: Use proper protocol transfer function
dmaengine: zynqmp_dma: Fix race condition in the probe
drm/tilcdc: ensure nonatomic iowrite64 is not used
mmc: avoid removing non-removable hosts during suspend
IB/ipoib: Avoid memory leak if the SA returns a different DGID
RDMA/cma: Use correct size when writing netlink stats
IB/umem: Fix use of npages/nmap fields
iser-target: avoid reinitializing rdma contexts for isert commands
vgacon: Set VGA struct resource types
omapdrm: panel: fix compatible vendor string for td028ttec1
drm/omap: DMM: Check for DMM readiness after successful transaction commit
pty: cancel pty slave port buf's work in tty_release
coresight: Fix disabling of CoreSight TPIU
pinctrl: Really force states during suspend/resume
pinctrl: rockchip: enable clock when reading pin direction register
iommu/vt-d: clean up pr_irq if request_threaded_irq fails
ip6_vti: adjust vti mtu according to mtu of lower device
RDMA/ocrdma: Fix permissions for OCRDMA_RESET_STATS
ARM: dts: aspeed-evb: Add unit name to memory node
nfsd4: permit layoutget of executable-only files
clk: Don't touch hardware when reparenting during registration
clk: axi-clkgen: Correctly handle nocount bit in recalc_rate()
clk: si5351: Rename internal plls to avoid name collisions
dmaengine: ti-dma-crossbar: Fix event mapping for TPCC_EVT_MUX_60_63
IB/mlx5: Fix integer overflows in mlx5_ib_create_srq
IB/mlx5: Fix out-of-bounds read in create_raw_packet_qp_rq
clk: migrate the count of orphaned clocks at init
RDMA/ucma: Fix access to non-initialized CM_ID object
RDMA/ucma: Don't allow join attempts for unsupported AF family
usb: gadget: f_hid: fix: Move IN request allocation to set_alt()
Linux 4.9.90
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
[ Upstream commit c82084117f ]
Set the resource type when we reserve VGA-related I/O port resources.
The resource code doesn't actually look at the type, so it inserts
resources without a type in the tree correctly even without this change.
But if we ever print a resource without a type, it looks like this:
vga+ [??? 0x000003c0-0x000003df flags 0x0]
Setting the type means it will be printed correctly as:
vga+ [io 0x000003c0-0x000003df]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 724ba8b30b upstream.
When this method is set, the caller expects struct console_font fields
to be properly initialized when it returns. Leave it unset otherwise
nonsensical (leaked kernel stack) values are returned to user space.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8aac7f3436 upstream.
fbcon can deal with vc_hi_font_mask (the upper 256 chars) and adjust
the vc attrs dynamically when vc_hi_font_mask is changed at
fbcon_init(). When the vc_hi_font_mask is set, it remaps the attrs in
the existing console buffer with one bit shift up (for 9 bits), while
it remaps with one bit shift down (for 8 bits) when the value is
cleared. It works fine as long as the font gets updated after fbcon
was initialized.
However, we hit a bizarre problem when the console is switched to
another fb driver (typically from vesafb or efifb to drmfb). At
switching to the new fb driver, we temporarily rebind the console to
the dummy console, then rebind to the new driver. During the
switching, we leave the modified attrs as is. Thus, the new fbcon
takes over the old buffer as if it were to contain 8 bits chars
(although the attrs are still shifted for 9 bits), and effectively
this results in the yellow color texts instead of the original white
color, as found in the bugzilla entry below.
An easy fix for this is to re-adjust the attrs before leaving the
fbcon at con_deinit callback. Since the code to adjust the attrs is
already present in the current fbcon code, in this patch, we simply
factor out the relevant code, and call it from fbcon_deinit().
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1000619
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This means all ->con_set_palette have to have the second parameter
const too now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 27a4c827c3
fbcon: use the cursor blink interval provided by vt
two attempts have been made at fixing a possible hang caused by
cursor_timer_handler. That function registers a timer to be triggered at
"jiffies + fbcon_ops.cur_blink_jiffies".
A new case had been encountered during initialisation of clcd-pl11x:
fbcon_fb_registered
do_fbcon_takeover
-> do_register_con_driver
fbcon_startup
(A) add_cursor_timer (with cur_blink_jiffies = 0)
-> do_bind_con_driver
visual_init
fbcon_init
(B) cur_blink_jiffies = msecs_to_jiffies(vc->vc_cur_blink_ms);
If we take an softirq anywhere between A and B (and we do),
cursor_timer_handler executes indefinitely.
Instead of patching all possible paths that lead to this case one at a
time, fix the issue at the source and initialise cur_blink_jiffies to
200ms when allocating fbcon_ops. This was its default value before
aforesaid commit. fbcon_cursor or fbcon_init will refine this value
downstream.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Cc: <stable@vger.kernel.org> # v4.2
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Since commit 27a4c827c3
fbcon: use the cursor blink interval provided by vt
a PPC64LE kernel fails to boot when fbcon_add_cursor_timer uses an
uninitialized ops->cur_blink_jiffies. Prevent by initializing
in fbcon_init before the call to info->fbops->fb_set_par.
Reported-and-tested-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Cc: <stable@vger.kernel.org> [v4.2]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull fbdev updates from Tomi Valkeinen:
"Minor fixes and cleanups"
* tag 'fbdev-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
video: fbdev: atmel_lcdfb: remove useless include
video: fbdev: pxa168fb: Use devm_clk_get
fbdev: ssd1307fb: fix error return code
fbdev: fix snprintf() limit in show_bl_curve()
video: fbdev: s3c-fb: Constify platform_device_id
video: fbdev: atmel: fix warning for const return value
video: fbdev: Drop owner assignment from platform_driver
video: fbdev: Drop owner assignment from i2c_driver
fbdev: remove unnecessary memset in vfb
framebuffer: disable vgacon on microblaze arch
fbdev: udlfb: remove unneeded initialization in few places
fbdev: Allow compile test of GPIO consumers if !GPIOLIB
fbdev: fix cea_modes array size
Architectures which support VGA console must define screen_info
structurture from "uapi/linux/screen_info.h". Otherwise undefined
symbol error occurs. Usually it's defined in "setup.c" for each
architecture.
If an architecture does not support VGA console (ARC's case) there are 2
ways: define a dummy instance of screen_info or add a negative
dependency for VGA_CONSOLE in to prevent selecting this option.
I've implemented the second way. However the best solution is to add
HAVE_VGA_CONSOLE option for targets which support VGA console. Then
turn off VGA_CONSOLE by default and add dependency to HAVE_VGA_CONSOLE.
But right now it's better to just add a negative dependency for ARC and
then consider how to collaborate about this issue with maintainers of
other architectures.
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Jaya Kumar <jayalk@intworks.biz>
Cc: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix an allmodconfig link failer on microblaze:
drivers/built-in.o: In function `vgacon_save_screen':
drivers/video/console/.tmp_vgacon.o:(.text+0x8fc10):
undefined reference to `screen_info'
Disable vgacon on microblaze because the symbol
struct screen_info screen_info;
is not defined for the microblaze arch.
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A sun7i-a20-olinuxino-micro fails to boot when kernel parameter
vt.global_cursor_default=0. The value is copied to vc->vc_deccm
causing the initialization of ops->cur_blink_jiffies to be skipped.
Unconditionally initialize it.
Reported-and-tested-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Pull tty/serial driver updates from Greg KH:
"Here's the tty and serial driver patches for 4.2-rc1.
A number of individual driver updates, some code cleanups, and other
minor things, full details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (152 commits)
Doc: serial-rs485.txt: update RS485 driver interface
Doc: tty.txt: remove mention of the BKL
MAINTAINERS: tty: add serial docs directory
serial: sprd: check for NULL after calling devm_clk_get
serial: 8250_pci: Correct uartclk for xr17v35x expansion chips
serial: 8250_pci: Add support for 12 port Exar boards
serial: 8250_uniphier: add bindings document for UniPhier UART
serial: core: cleanup in uart_get_baud_rate()
serial: stm32-usart: Add STM32 USART Driver
tty/serial: kill off set_irq_flags usage
tty: move linux/gsmmux.h to uapi
doc: dt: add documentation for nxp,lpc1850-uart
serial: 8250: add LPC18xx/43xx UART driver
serial: 8250_uniphier: add UniPhier serial driver
serial: 8250_dw: support ACPI platforms with integrated DMA engine
serial: of_serial: check the return value of clk_prepare_enable()
serial: of_serial: use devm_clk_get() instead of clk_get()
serial: earlycon: Add support for big-endian MMIO accesses
serial: sirf: use hrtimer for data rx
serial: sirf: correct the fifo empty_bit
...
Commit 27a4c827c3 ("fbcon: use the cursor blink interval provided by
vt") unconditionally removes the cursor blink timer. Unfortunately that
wreaks havoc under some circumstances. An easily reproducible way is to
use both the framebuffer console and a debug serial port as the console
output for kernel messages (e.g. "console=ttyS0 console=tty1" on the
kernel command-line. Upon boot this triggers a warning from within the
del_timer_sync() function because it is called from IRQ context:
[ 5.070096] ------------[ cut here ]------------
[ 5.070110] WARNING: CPU: 0 PID: 0 at ../kernel/time/timer.c:1098 del_timer_sync+0x4c/0x54()
[ 5.070115] Modules linked in:
[ 5.070120] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.1.0-rc4-next-20150519 #1
[ 5.070123] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 5.070142] [] (unwind_backtrace) from [] (show_stack+0x10/0x14)
[ 5.070156] [] (show_stack) from [] (dump_stack+0x70/0xbc)
[ 5.070164] [] (dump_stack) from [] (warn_slowpath_common+0x74/0xb0)
[ 5.070169] [] (warn_slowpath_common) from [] (warn_slowpath_null+0x1c/0x24)
[ 5.070174] [] (warn_slowpath_null) from [] (del_timer_sync+0x4c/0x54)
[ 5.070183] [] (del_timer_sync) from [] (fbcon_del_cursor_timer+0x2c/0x40)
[ 5.070190] [] (fbcon_del_cursor_timer) from [] (fbcon_cursor+0x9c/0x180)
[ 5.070198] [] (fbcon_cursor) from [] (hide_cursor+0x30/0x98)
[ 5.070204] [] (hide_cursor) from [] (vt_console_print+0x2a8/0x340)
[ 5.070212] [] (vt_console_print) from [] (call_console_drivers.constprop.23+0xc8/0xec)
[ 5.070218] [] (call_console_drivers.constprop.23) from [] (console_unlock+0x498/0x4f0)
[ 5.070223] [] (console_unlock) from [] (vprintk_emit+0x1f0/0x508)
[ 5.070228] [] (vprintk_emit) from [] (vprintk_default+0x24/0x2c)
[ 5.070234] [] (vprintk_default) from [] (printk+0x70/0x88)
After which the system starts spewing all kinds of weird and seemingly
unrelated error messages.
This commit fixes this by restoring the condition under which the call
to fbcon_del_cursor_timer() happens.
Reported-by: Daniel Stone <daniel@fooishbar.org>
Reported-by: Kevin Hilman <khilman@kernel.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Andrew Vagin <avagin@virtuozzo.com>
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vt now provides a cursor blink interval via vc_data. Use this
interval instead of the currently hardcoded 200 msecs. Store it in
fbcon_ops to avoid locking the console in cursor_timer_handler().
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PA-RISC already handled the dummy console screen size selection in
Kconfig, so generalize this to other platforms.
ARM keeps on using screen_info, which is filled in by
platform-specific code, or from ATAGS.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Various fb drivers register themselves before module_init so as to have a
console as early as possible, this is of little use if fbcon does not
initialize early too.
Fbcon cannot initialize earlier then fs_initcall, because then the creation
of /sys/class/graphics/fbcon will fail.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Since strsep is used to tokenize the options string, after each option
match the code should use "continue" to get the next token from strsep.
This patch applies this pattern consistently.
Previously, for "scrollback:" and "map:" the parse code would return
(unconditionally: strsep ensures *options != ','), causing any
following option to be ignored, while for "vc:" the parse code would
go on to parse further options within the same token, which could lead
to invalid input being accepted.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The framebuffer code uses the current background color to fill the border
when switching consoles, however, this results in inconsistent behavior.
For example:
- start Midnigh Commander
- the border is black
- switch to another console and switch back
- the border is cyan
- type something into the command line in mc
- the border is cyan
- switch to another console and switch back
- the border is black
- press F9 to go to menu
- the border is black
- switch to another console and switch back
- the border is dark blue
When switching to a console with Midnight Commander, the border is random
color that was left selected by the slang subsystem.
This patch fixes this inconsistency by always using black as the
background color when switching consoles.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
First round of fixes for 3.16-rc, mostly cc: stable, and the vt/vgacon
fixes from Daniel [1] to avoid hangs and unclaimed register errors on
module load/reload.
* tag 'drm-intel-fixes-2014-06-17' of git://anongit.freedesktop.org/drm-intel:
drm/i915/bdw: remove erroneous chv specific workarounds from bdw code
drm/i915: fix possible refcount leak when resetting forcewake
drm/i915: Reorder semaphore deadlock check
drm/i95: Initialize active ring->pid to -1
drm/i915: set backlight duty cycle after backlight enable for gen4
drm/i915: Avoid div-by-zero when pixel_multiplier is zero
drm/i915: Disable FBC by default also on Haswell and later
drm/i915: Kick out vga console
drm/i915: Fixup global gtt cleanup
vt: Don't ignore unbind errors in vt_unbind
vt: Fix up unregistration of vt drivers
vt: Fix replacement console check when unbinding
Touching the VGA resources on an IVB EFI machine causes hard hangs when
we then kick out the efifb. Ouch.
Apparently this also prevents unclaimed register errors on hsw and
hard machine hangs on my i855gm when trying to unbind fbcon.
Also, we want this to make I915_FBDEV=n safe.
v2: Rebase and pimp commit message.
v3: We also need to unregister the vga console, otherwise the unbind
of the fb console before module unload might resurrect it again.
v4: Ignore errors when the vga console is already unregistered - this
can happen when e.g. reloading i915.ko.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67813
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull main fbdev changes from Tomi Valkeinen:
"Mainly fixes and small improvements. The biggest change seems to be
backlight control support for mx3fb"
* tag 'fbdev-main-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (31 commits)
drivers/video/fbdev/fb-puv3.c: Add header files for function unifb_mmap
video: fbdev: s3fb.c: Fix for possible null pointer dereference
video: fbdev: grvga.c: Fix for possible null pointer dereference
matroxfb: perform a dummy read of M_STATUS
video: of: display_timing: fix default native-mode setting
video: delete unneeded call to platform_get_drvdata
video: mx3fb: Add backlight control support
video: omap: delete support for early fbmem allocation
video: of: display_timing: remove two unsafe error messages
fbdev: fbmem: remove positive test on unsigned values
fbcon: Fix memory leak in con2fb_release_oldinfo()
video: Kconfig: Add a dependency to the Goldfish framebuffer driver
video: exynos: Add a dependency to the menu
video: mx3fb: Use devm_kzalloc
video/nuc900: allow modular build
video: atmel needs FB_BACKLIGHT
video: export fb_prepare_logo
video/mbx: fix building debugfs support
video/omap: fix modular build
video: clarify I2C dependencies
...
The vc_data.vc_uni_pagedir filed is currently long int, supposedly to
be served generically. This, however, leads to lots of cast to
pointer, and rather it worsens the readability significantly.
Actually, we have now only a single uni_pagedir map implementation,
and this won't change likely. So, it'd be much more simple and
error-prone to just use the exact pointer for struct uni_pagedir
instead of long.
Ditto for vc_uni_pagedir_loc. It's a pointer to the uni_pagedir, thus
it can be changed similarly to the exact type.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vgacon driver prepares a two element array of uni_pagedir_loc and
uses the second item as its own reference counter for sharing the
uni_pagedir. And the code assumes blindly that the second item is
available if the assigned vc_uni_pagedir isn't the standard one, which
might be wrong (although currently it's so).
This patch fixes that wrong assumption, and gives a slight cleanup
along with it: namely, instead of array, just give the uni_pagedir_loc
and a separate refcount variable. It makes the code a bit more
understandable at first glance.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drivers/video directory is a mess. It contains generic video related
files, directories for backlight, console, linux logo, lots of fbdev
device drivers, fbdev framework files.
Make some order into the chaos by creating drivers/video/fbdev
directory, and move all fbdev related files there.
No functionality is changed, although I guess it is possible that some
subtle Makefile build order related issue could be created by this
patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When FB_EVENT_FB_UNBIND is sent, fbcon has two paths, one path taken
when there is another frame buffer to switch any affected vcs to and
another path when there isn't.
In the case where there is another frame buffer to use,
fbcon_fb_unbind calls set_con2fb_map to remap all of the affected vcs
to the replacement frame buffer. set_con2fb_map will eventually call
con2fb_release_oldinfo when the last vcs gets unmapped from the old
frame buffer.
con2fb_release_oldinfo frees the fbcon data that is hooked off of the
fb_info structure, including the cursor timer.
In the case where there isn't another frame buffer to use,
fbcon_fb_unbind simply calls fbcon_unbind, which doesn't clear the
con2fb_map or free the fbcon data hooked from the fb_info
structure. In particular, it doesn't stop the cursor blink timer. When
the fb_info structure is then freed, we end up with a timer queue
pointing into freed memory and "bad things" start happening.
This patch first changes con2fb_release_oldinfo so that it can take a
NULL pointer for the new frame buffer, but still does all of the
deallocation and cursor timer cleanup.
Finally, the patch tries to replicate some of what set_con2fb_map does
by clearing the con2fb_map for the affected vcs and calling the
modified con2fb_release_info function to clean up the fb_info structure.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The built-in ROM fonts lack many necessary ASCII characters, which is
why it makes sens to prefer the Linux fonts instead if they are
available. This makes consoles on STI graphics cards which are not
supported by the stifb driver (e.g. Visualize FXe) looks much nicer.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v3.13
