[ Upstream commit ec5895c0f2 ]
Function mc146818_get_time() contains an elaborate mechanism of reading
the RTC time while no RTC update is in progress. It turns out that
reading the RTC alarm clock also requires avoiding the RTC update.
Therefore, the mechanism in mc146818_get_time() should be reused - so
extract it into a separate function.
The logic in mc146818_avoid_UIP() is same as in mc146818_get_time()
except that after every
if (CMOS_READ(RTC_FREQ_SELECT) & RTC_UIP) {
there is now "mdelay(1)".
To avoid producing a very unreadable patch, mc146818_get_time() will be
refactored to use mc146818_avoid_UIP() in the next patch.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210200131.153887-6-mat.jonczyk@o2.pl
Stable-dep-of: cd17420ebe ("rtc: cmos: avoid UIP when writing alarm time")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea6fa4961a ]
To prevent an infinite loop in mc146818_get_time(),
commit 211e5db19d ("rtc: mc146818: Detect and handle broken RTCs")
added a check for RTC availability. Together with a later fix, it
checked if bit 6 in register 0x0d is cleared.
This, however, caused a false negative on a motherboard with an AMD
SB710 southbridge; according to the specification [1], bit 6 of register
0x0d of this chipset is a scratchbit. This caused a regression in Linux
5.11 - the RTC was determined broken by the kernel and not used by
rtc-cmos.c [3]. This problem was also reported in Fedora [4].
As a better alternative, check whether the UIP ("Update-in-progress")
bit is set for longer then 10ms. If that is the case, then apparently
the RTC is either absent (and all register reads return 0xff) or broken.
Also limit the number of loop iterations in mc146818_get_time() to 10 to
prevent an infinite loop there.
The functions mc146818_get_time() and mc146818_does_rtc_work() will be
refactored later in this patch series, in order to fix a separate
problem with reading / setting the RTC alarm time. This is done so to
avoid a confusion about what is being fixed when.
In a previous approach to this problem, I implemented a check whether
the RTC_HOURS register contains a value <= 24. This, however, sometimes
did not work correctly on my Intel Kaby Lake laptop. According to
Intel's documentation [2], "the time and date RAM locations (0-9) are
disconnected from the external bus" during the update cycle so reading
this register without checking the UIP bit is incorrect.
[1] AMD SB700/710/750 Register Reference Guide, page 308,
https://developer.amd.com/wordpress/media/2012/10/43009_sb7xx_rrg_pub_1.00.pdf
[2] 7th Generation Intel ® Processor Family I/O for U/Y Platforms [...] Datasheet
Volume 1 of 2, page 209
Intel's Document Number: 334658-006,
https://www.intel.com/content/dam/www/public/us/en/documents/datasheets/7th-and-8th-gen-core-family-mobile-u-y-processor-lines-i-o-datasheet-vol-1.pdf
[3] Functions in arch/x86/kernel/rtc.c apparently were using it.
[4] https://bugzilla.redhat.com/show_bug.cgi?id=1936688
Fixes: 211e5db19d ("rtc: mc146818: Detect and handle broken RTCs")
Fixes: ebb22a0594 ("rtc: mc146818: Dont test for bit 0-5 in Register D")
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210200131.153887-5-mat.jonczyk@o2.pl
Stable-dep-of: cd17420ebe ("rtc: cmos: avoid UIP when writing alarm time")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dd8d6cb9e ]
There are 4 users of mc146818_get_time() and none of them was checking
the return value from this function. Change this.
Print the appropriate warnings in callers of mc146818_get_time() instead
of in the function mc146818_get_time() itself, in order not to add
strings to rtc-mc146818-lib.c, which is kind of a library.
The callers of alpha_rtc_read_time() and cmos_read_time() may use the
contents of (struct rtc_time *) even when the functions return a failure
code. Therefore, set the contents of (struct rtc_time *) to 0x00,
which looks more sensible then 0xff and aligns with the (possibly
stale?) comment in cmos_read_time:
/*
* If pm_trace abused the RTC for storage, set the timespec to 0,
* which tells the caller that this RTC value is unusable.
*/
For consistency, do this in mc146818_get_time().
Note: hpet_rtc_interrupt() may call mc146818_get_time() many times a
second. It is very unlikely, though, that the RTC suddenly stops
working and mc146818_get_time() would consistently fail.
Only compile-tested on alpha.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-alpha@vger.kernel.org
Cc: x86@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210200131.153887-4-mat.jonczyk@o2.pl
Stable-dep-of: cd17420ebe ("rtc: cmos: avoid UIP when writing alarm time")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1aba37569 ]
It appears mc146818_get_time() and mc146818_set_time() now correctly
use the century register as specified in the ACPI FADT table. It is not
clear what else could be done here.
These comments were introduced by
commit 7be2c7c96a ("[PATCH] RTC framework driver for CMOS RTCs")
in 2007, which originally referenced function get_rtc_time() in
include/asm-generic/rtc.h .
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210716210437.29622-1-mat.jonczyk@o2.pl
Stable-dep-of: cd17420ebe ("rtc: cmos: avoid UIP when writing alarm time")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 211e5db19d ]
The recent fix for handling the UIP bit unearthed another issue in the RTC
code. If the RTC is advertised but the readout is straight 0xFF because
it's not available, the old code just proceeded with crappy values, but the
new code hangs because it waits for the UIP bit to become low.
Add a sanity check in the RTC CMOS probe function which reads the RTC_VALID
register (Register D) which should have bit 0-6 cleared. If that's not the
case then fail to register the CMOS.
Add the same check to mc146818_get_time(), warn once when the condition
is true and invalidate the rtc_time data.
Reported-by: Mickaël Salaün <mic@digikod.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Mickaël Salaün <mic@linux.microsoft.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/87tur3fx7w.fsf@nanos.tec.linutronix.de
Stable-dep-of: cd17420ebe ("rtc: cmos: avoid UIP when writing alarm time")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05a0302c35 ]
The MC146818 driver is prone to read garbage from the RTC. There are
several issues all related to the update cycle of the MC146818. The chip
increments seconds obviously once per second and indicates that by a bit in
a register. The bit goes high 244us before the actual update starts. During
the update the readout of the time values is undefined.
The code just checks whether the update in progress bit (UIP) is set before
reading the clock. If it's set it waits arbitrary 20ms before retrying,
which is ample because the maximum update time is ~2ms.
But this check does not guarantee that the UIP bit goes high and the actual
update happens during the readout. So the following can happen
0.997 UIP = False
-> Interrupt/NMI/preemption
0.998 UIP -> True
0.999 Readout <- Undefined
To prevent this rework the code so it checks UIP before and after the
readout and if set after the readout try again.
But that's not enough to cover the following:
0.997 UIP = False
Readout seconds
-> NMI (or vCPU scheduled out)
0.998 UIP -> True
update completes
UIP -> False
1.000 Readout minutes,....
UIP check succeeds
That can make the readout wrong up to 59 seconds.
To prevent this, read the seconds value before the first UIP check,
validate it after checking UIP and after reading out the rest.
It's amazing that the original i386 code had this actually correct and
the generic implementation of the MC146818 driver got it wrong in 2002 and
it stayed that way until today.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201206220541.594826678@linutronix.de
Stable-dep-of: cd17420ebe ("rtc: cmos: avoid UIP when writing alarm time")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8d3c106e19 upstream.
pagetable walks on address ranges mapped by VMAs can be done under the
mmap lock, the lock of an anon_vma attached to the VMA, or the lock of the
VMA's address_space. Only one of these needs to be held, and it does not
need to be held in exclusive mode.
Under those circumstances, the rules for concurrent access to page table
entries are:
- Terminal page table entries (entries that don't point to another page
table) can be arbitrarily changed under the page table lock, with the
exception that they always need to be consistent for
hardware page table walks and lockless_pages_from_mm().
This includes that they can be changed into non-terminal entries.
- Non-terminal page table entries (which point to another page table)
can not be modified; readers are allowed to READ_ONCE() an entry, verify
that it is non-terminal, and then assume that its value will stay as-is.
Retracting a page table involves modifying a non-terminal entry, so
page-table-level locks are insufficient to protect against concurrent page
table traversal; it requires taking all the higher-level locks under which
it is possible to start a page walk in the relevant range in exclusive
mode.
The collapse_huge_page() path for anonymous THP already follows this rule,
but the shmem/file THP path was getting it wrong, making it possible for
concurrent rmap-based operations to cause corruption.
Link: https://lkml.kernel.org/r/20221129154730.2274278-1-jannh@google.com
Link: https://lkml.kernel.org/r/20221128180252.1684965-1-jannh@google.com
Link: https://lkml.kernel.org/r/20221125213714.4115729-1-jannh@google.com
Fixes: 27e1f82731 ("khugepaged: enable collapse pmd for pte-mapped THP")
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[manual backport: this code was refactored from two copies into a common
helper between 5.15 and 6.0]
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a487069e11 ]
Add RmNet support for LARA-L6.
LARA-L6 module can be configured (by AT interface) in three different
USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1341) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1342) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1343) with 4 serial
interface and 1 CDC-ECM virtual network interface
In RmNet mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3aa07f7289 ]
If there's a disconnection while operating in eSS, there may be a delay
in VBUS drop response from the connector. In that case, the internal
link state may drop to operate in usb2 speed while the controller thinks
the VBUS is still high. The driver must make sure to disable
GUSB2PHYCFG.SUSPHY when sending endpoint command while in usb2 speed.
The End Transfer command may be called, and only that command needs to
go through at this point. Let's keep it simple and unconditionally
disable GUSB2PHYCFG.SUSPHY whenever we issue the command.
This scenario is not seen in real hardware. In a rare case, our
prototype type-c controller/interface may have a slow response
triggerring this issue.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/5651117207803c26e2f22ddf4e5ce9e865dcf7c7.1668045468.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a11452a370 ]
When trying to see if we can clone a file range, there are cases where we
end up sending two write operations in case the inode from the source root
has an i_size that is not sector size aligned and the length from the
current offset to its i_size is less than the remaining length we are
trying to clone.
Issuing two write operations when we could instead issue a single write
operation is not incorrect. However it is not optimal, specially if the
extents are compressed and the flag BTRFS_SEND_FLAG_COMPRESSED was passed
to the send ioctl. In that case we can end up sending an encoded write
with an offset that is not sector size aligned, which makes the receiver
fallback to decompressing the data and writing it using regular buffered
IO (so re-compressing the data in case the fs is mounted with compression
enabled), because encoded writes fail with -EINVAL when an offset is not
sector size aligned.
The following example, which triggered a bug in the receiver code for the
fallback logic of decompressing + regular buffer IO and is fixed by the
patchset referred in a Link at the bottom of this changelog, is an example
where we have the non-optimal behaviour due to an unaligned encoded write:
$ cat test.sh
#!/bin/bash
DEV=/dev/sdj
MNT=/mnt/sdj
mkfs.btrfs -f $DEV > /dev/null
mount -o compress $DEV $MNT
# File foo has a size of 33K, not aligned to the sector size.
xfs_io -f -c "pwrite -S 0xab 0 33K" $MNT/foo
xfs_io -f -c "pwrite -S 0xcd 0 64K" $MNT/bar
# Now clone the first 32K of file bar into foo at offset 0.
xfs_io -c "reflink $MNT/bar 0 0 32K" $MNT/foo
# Snapshot the default subvolume and create a full send stream (v2).
btrfs subvolume snapshot -r $MNT $MNT/snap
btrfs send --compressed-data -f /tmp/test.send $MNT/snap
echo -e "\nFile bar in the original filesystem:"
od -A d -t x1 $MNT/snap/bar
umount $MNT
mkfs.btrfs -f $DEV > /dev/null
mount $DEV $MNT
echo -e "\nReceiving stream in a new filesystem..."
btrfs receive -f /tmp/test.send $MNT
echo -e "\nFile bar in the new filesystem:"
od -A d -t x1 $MNT/snap/bar
umount $MNT
Before this patch, the send stream included one regular write and one
encoded write for file 'bar', with the later being not sector size aligned
and causing the receiver to fallback to decompression + buffered writes.
The output of the btrfs receive command in verbose mode (-vvv):
(...)
mkfile o258-7-0
rename o258-7-0 -> bar
utimes
clone bar - source=foo source offset=0 offset=0 length=32768
write bar - offset=32768 length=1024
encoded_write bar - offset=33792, len=4096, unencoded_offset=33792, unencoded_file_len=31744, unencoded_len=65536, compression=1, encryption=0
encoded_write bar - falling back to decompress and write due to errno 22 ("Invalid argument")
(...)
This patch avoids the regular write followed by an unaligned encoded write
so that we end up sending a single encoded write that is aligned. So after
this patch the stream content is (output of btrfs receive -vvv):
(...)
mkfile o258-7-0
rename o258-7-0 -> bar
utimes
clone bar - source=foo source offset=0 offset=0 length=32768
encoded_write bar - offset=32768, len=4096, unencoded_offset=32768, unencoded_file_len=32768, unencoded_len=65536, compression=1, encryption=0
(...)
So we get more optimal behaviour and avoid the silent data loss bug in
versions of btrfs-progs affected by the bug referred by the Link tag
below (btrfs-progs v5.19, v5.19.1, v6.0 and v6.0.1).
Link: https://lore.kernel.org/linux-btrfs/cover.1668529099.git.fdmanana@suse.com/
Reviewed-by: Boris Burkov <boris@bur.io>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05530ef7cf ]
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed.
seq_copy_in_user() and seq_copy_in_kernel() did not have prototypes
matching snd_seq_dump_func_t. Adjust this and remove the casts. There
are not resulting binary output differences.
This was found as a result of Clang's new -Wcast-function-type-strict
flag, which is more sensitive than the simpler -Wcast-function-type,
which only checks for type width mismatches.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/202211041527.HD8TLSE1-lkp@intel.com
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221118232346.never.380-kees@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da74858a47 ]
The clock source and the sched_clock provided by the arm_global_timer
on Rockchip rk3066a/rk3188 are quite unstable because their rates
depend on the CPU frequency.
Recent changes to the arm_global_timer driver makes it impossible to use.
On the other side, the arm_global_timer has a higher rating than the
ROCKCHIP_TIMER, it will be selected by default by the time framework
while we want to use the stable Rockchip clock source.
Keep the arm_global_timer disabled in order to have the
DW_APB_TIMER (rk3066a) or ROCKCHIP_TIMER (rk3188) selected by default.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/f275ca8d-fd0a-26e5-b978-b7f3df815e0a@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ca507bf99 ]
DSPCLK_DIV field in WM8962_CLOCKING1 register is used to generate
correct frequency of LRCLK and BCLK. Sometimes the read-only value
can't be updated timely after enabling SYSCLK. This results in wrong
calculation values. Delay is introduced here to wait for newest value
from register. The time of the delay should be at least 500~1000us
according to test.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221109121354.123958-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 340a982825 ]
Actually in no-MMU SoCs(i.e. i.MXRT) ZERO_PAGE(vaddr) expands to
```
virt_to_page(0)
```
that in order expands to:
```
pfn_to_page(virt_to_pfn(0))
```
and then virt_to_pfn(0) to:
```
((((unsigned long)(0) - PAGE_OFFSET) >> PAGE_SHIFT) +
PHYS_PFN_OFFSET)
```
where PAGE_OFFSET and PHYS_PFN_OFFSET are the DRAM offset(0x80000000) and
PAGE_SHIFT is 12. This way we obtain 16MB(0x01000000) summed to the base of
DRAM(0x80000000).
When ZERO_PAGE(0) is then used, for example in bio_add_page(), the page
gets an address that is out of DRAM bounds.
So instead of using fake virtual page 0 let's allocate a dedicated
zero_page during paging_init() and assign it to a global 'struct page *
empty_zero_page' the same way mmu.c does and it's the same approach used
in m68k with commit dc068f4621 as discussed here[0]. Then let's move
ZERO_PAGE() definition to the top of pgtable.h to be in common between
mmu.c and nommu.c.
[0]: https://lore.kernel.org/linux-m68k/2a462b23-5b8e-bbf4-ec7d-778434a3b9d7@google.com/T/#m1266ceb63
ad140743174d6b3070364d3c9a5179b
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit c5589c7eec ("ANDROID: dma-buf: Add vendor hook for
deferred dmabuf sysfs stats release") introduced a build breakage
on non-GKI targets which don't have CONFIG_DMABUF_SYSFS_STATS
enabled. It is due to invisibility of struct dma_buf_sysfs_entry
in the trace hook header file. We can get away with it by moving
the header inclusion from trace hook header to vendor hooks driver.
Bug: 261818075
Change-Id: Ibb79bd67c9f1b36fe2b5d569ab9369f376a78b77
Signed-off-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
The commit 5aec776ef8 ("BACKPORT: ANDROID: dma-buf: Move sysfs work
out of DMA-BUF export path) re-purposed kobject as work_struct temporarily
to create the sysfs entries asynchronously. The author knows what he is
doing and rightly added a build assert if kobject struct size is smaller than
the work_struct size. We are hitting this build assert on a non-GKI platform
where CONFIG_ANDROID_KABI_RESERVE is not set. Fix this problem by allocating
a new union with dma_buf_sysfs_entry structure and temporary structure as
members. We only end up allocating more memory (because of union) only when
kobject size is smaller than work_struct which the original patch any way
assumed would never be true.
Bug: 261818147
Change-Id: Ifb089bf80d8a3a44ece9f05fc0b99ee76cb11645
Signed-off-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Some linux app(cusor) may set negative coordinates(crtc_x/y)
And some linux app(mpv) may set coordinates outside the screen.
These are both unsupported on rockchip vop.
so we use clipped coordinates here.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Change-Id: Id2322113f0973271997575678cda478a9987266b
if isp work in isp_unit mode and hdr mode and online mode,
buffer addr for half frame of right side must 16 byte align,
otherwise, the buffer to ddr need config to uncompact
Signed-off-by: Zefa Chen <zefa.chen@rock-chips.com>
Change-Id: I29792f2fbeed410d0c640b8bee27f741915086be
Reorder and add missing functions on !CONFIG_ROCKCHIP_SIP.
Return SIP_RET_NOT_SUPPORTED on !CONFIG_ROCKCHIP_SIP.
Change-Id: Ic02b5680ba00cb5186a9180926199ac534d5838f
Signed-off-by: Tao Huang <huangtao@rock-chips.com>
This reverts commit 940b774069 which is
commit c981cdfb99 upstream.
It breaks the Android ABI so revert it for now. If this is needed in
the future, it can be brought back in an ABI safe way.
Bug: 161946584
Change-Id: Ia5d24c9adcb06166546c42810759b9193d4eaceb
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Commit c099d12c55 ("error-injection: Add prompt for function error
injection") removed the "default y" selection for this option, so it
needs to be added manually to the gki_defconfig files in order to
preserve the option, AND to keep the stable ABI.
Fixes: c099d12c55 ("error-injection: Add prompt for function error injection")
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: Ie36b7bab650356d1bf24625961adf33a725258d2
