Both the last two cases are only relevant if something has failed and
something needs to be written (but not over-written), and if it is OK
to pre-read blocks at this point. So factor out those tests and
explain them.
Signed-off-by: NeilBrown <neilb@suse.de>
Some of the conditions in need_this_block have very straight
forward motivation. Separate those out and document them.
Signed-off-by: NeilBrown <neilb@suse.de>
fetch_block() has a very large and hard to read 'if' condition.
Separate it into its own function so that it can be
made more readable.
Signed-off-by: NeilBrown <neilb@suse.de>
67f455486d introduced a call to
md_wakeup_thread() when adding to the delayed_list. However the md
thread is woken up unconditionally just below.
Remove the unnecessary wakeup call.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Introduce helper function acpi_dev_filter_resource_type(), which may
be used by acpi_dev_get_resources() to filer out resource based on
resource type.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add field offset to struct resource_list_entry to host address space
translation offset so it could be used to represent bridge resources.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add translation_offset into the result address for bridge window
resources to form the master side address.
Currently acpi_dev_resource_{ext_}address_space() are only used for
devices instead of bridges, so it won't break current users. Later
it will be used to support PCI host bridge drivers.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Change function acpi_dev_resource_address_space() and
acpi_dev_resource_ext_address_space() to return address space
translation offset.
It's based on a patch from Yinghai Lu <yinghai@kernel.org>.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Also set flag IORESOURCE_UNSET for unassigned resource in addition to
IORESOURCE_DISABLED to mark resource as unassigned.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Normalize return value of resource parse functions as:
1) return "true" if resource is assigned.
2) return "false" and IORESOURCE_DISABLED setting in res->flags if
resource is unassigned.
3) return "false" and zeroing res->flags if it's not an valid or
expected resource.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
According to ACPI spec 5, section 6.4.3.1 "24-Bit Memory Range Descriptor",
minimum, maximum and address_length field in struct acpi_resource_memory24
is in granularity of 256-bytes. So shift 8-bit left to get correct address.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Normal memory and io resources have window always set to false. Move
the flag logic to the unified address space parser.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With the unions in place which let us identify the substructs we can
use a single parser for address_space and ext_address_space.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the parser disables a resource during parsing, let it return false,
so the calling code does not need to implement further checks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Also apply length check to IO resources.
[Jiang] Remove enforcement that resource starting address must be
non-zero.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Check whether the resulting length is the same as the given
length. Check for start <= end as well.
We need to hand in the resource for this, so we can apply the flags
directly.
[Jiang] Remove enforcement that resource starting address must be
non-zero.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
According to i.MX23 and i.MX28 reference manual [1],[2] the fractional
clock control register is 32-bit wide, but is separated in 4 parts.
So write instructions must not apply to more than 1 part at once.
The clk init for the i.MX28 violates this restriction and all the other
accesses on that register suggest that there isn't such a restriction.
This patch restricts the access to this register to byte instructions and
extends the comment in the init functions.
Btw the imx23 init now uses a R-M-W sequence just like imx28 init
to avoid any clock glitches.
The changes has been tested with a i.MX23 and a i.MX28 board.
[1] - http://cache.freescale.com/files/dsp/doc/ref_manual/IMX23RM.pdf
[2] - http://cache.freescale.com/files/dsp/doc/ref_manual/MCIMX28RM.pdf
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Introduce a common ->enter callback routine for the ACPI cpuidle
driver, acpi_idle_enter(), which helps to reduce code complexity,
size and duplication and prevents theoretically possible failues that
an incorrect routine may be run to enter the given idle state due to
a firmware bug (eg. when _CST returns a different set of states for
each processor).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_idle_enter_c1() and acpi_idle_enter_simple() are close enough to
each other that they can be merged into one function which reduces
duplication of code quite a bit.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use the generic facility instead of a home-grown one.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert dprintk to netdev_dbg where appropriate.
Remove dvb_net_debug module_param.
Remove __func__ from output as that can be added by dynamic_debug.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
No need for more macros, so remove them and use the kernel extension.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adjusts boolean assignments from 0/1 to false/true.
And accordingly, it also adjusts the if conditions.
Signed-off-by: Heba Aamer <heba93aamer@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Setting a dev_pm_ops suspend/resume pair but not a set of
hibernation functions means those pm functions will not be
called upon hibernation.
Fix this by using SIMPLE_DEV_PM_OPS, which appropriately
assigns the suspend and hibernation handlers and move
mp102_suspend/tmp102_resume under CONFIG_PM_SLEEP to avoid
build warnings.
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
[groeck: Declare tmp102_dev_pm_ops as static variable]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of implement its own logic, use the already-defined one.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch is based on Antti's silabs branch.
Add support for 1.7 MHz bandwidth. Supported in all versions of Si2168 according to short data sheets.
[mchehab@osg.samsung.com: Fix CodingStyle]
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch should is based on Antti's silabs branch.
According to dvb-frontend.h set_frontend may be called with bandwidth_hz set to 0 if automatic bandwidth is required. Si2168 does not support automatic bandwidth and does not declare FE_CAN_BANDWIDTH_AUTO in caps.
This patch will change the behaviour in a way that EINVAL is returned if bandwidth_hz is 0.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Host drivers have different ways to sends their "init stream" to the
card. Some need to do it as part of a request, some do it from the
->set_ios() callback in the MMC_POWER_ON state and some don't send an
"init stream" at all.
To be able to use the reset GPIOs from the simple MMC power sequence
provider, the card need to be powered and the "init stream" must not
have been sent.
To cope with these requirements, invoke mmc_pwrseq_post_power_on()
prior we change the state to MMC_POWER_ON in mmc_power_up().
Host drivers shall perform power up operations in the MMC_POWER_UP
state. Unfortunate three hosts (au1xmmc, cb710-mmc and toshsd) don't
conform to this expectation. Instead those ignore the MMC_POWER_UP
state and delays their power up operations to the MMC_POWER_ON state.
Those hosts needs to change their behavior to enable proper support for
the simple MMC power sequence provider.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Previously, delta filtering was applied TSC co-ordinate readouts before
reporting a single value to user space. This patch replaces delta filtering
with median filtering. Median filtering sorts co-ordinate readouts, drops
min and max values, and reports the average of remaining values. This
method is more sensible than delta filtering. Median filtering is applied
only if number of readouts is greater than 3 else just average of
co-ordinate readouts is reported.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch reads charge delay from tsc DT node and writes to
REG_CHARGEDELAY register. If the charge delay is not specified in DT then
default value of 0x400(CHARGEDLY_OPENDLY) is used.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
TSC interrupt handler had udelay to avoid reporting of false pen-up
interrupt to user space. This patch implements workaround suggesting in
Advisory 1.0.31 of silicon errata for am335x, thus eliminating udelay and
touchscreen lag. This also improves performance of touchscreen and
eliminates sudden jump of cursor at touch release.
IDLECONFIG and CHARGECONFIG registers are to be configured with same values
in order to eliminate false pen-up events. This workaround may result in
false pen-down to be detected, hence considerable charge step delay needs
to be added. The charge delay is set to 0xB000 (in terms of ADC clock
cycles) by default.
TSC steps are disabled at the end of every sampling cycle and EOS bit is
set. Once the EOS bit is set, the TSC steps need to be re-enabled to begin
next sampling cycle.
Signed-off-by: Brad Griffis <bgriffis@ti.com>
[vigneshr@ti.com: Ported the patch from v3.12 to v3.19rc1]
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch makes the initial changes required to workaround TSC-false
pen-up interrupts. It is required to implement these changes in order to
remove udelay in the TSC interrupt handler and false pen-up events. The
charge step is to be executed immediately after sampling X+. Hence TSC is
made to use higher numbered steps (steps 5 to 16 for 5 co-ordinate
readouts, 4 wire TSC configuration) and ADC to use lower ones. Further X
co-ordinate readouts must be the last to be sampled, thus co-ordinates are
sampled in the order Y-Z-X.
Signed-off-by: Brad Griffis <bgriffis@ti.com>
[vigneshr@ti.com: Ported the patch from v3.12 to v3.19rc1]
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull gpio fixes from Linus Walleij:
"Yet more GPIO fixes for the v3.19 series.
There is a high bug-spot activity in GPIO this merge window, much due
to Johan Hovolds spearheading into actually exercising the removal
path for GPIO chips, something that was never really exercised before.
The other two fixes are augmenting erroneous behaviours in two
specific drivers for minor systems.
Summary from signed tag:
- Two fixes stabilizing that which was never stable before: removal
of GPIO chips, now let's stop leaking memory.
- Make sure OMAP IRQs are usable when the irqchip API is used
orthogonally to the gpiochip API.
- Provide a default GPIO base for the mcp23s08 driver"
* tag 'gpio-v3.19-5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: sysfs: fix memory leak in gpiod_sysfs_set_active_low
gpio: sysfs: fix memory leak in gpiod_export_link
gpio: mcp23s08: handle default gpio base
gpio: omap: Fix bad device access with setup_irq()
symbol-rate report was wrongly removed off by the commit:906aaf5a .
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This allows calling the original functions providing the streaming is off.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Create dm04_read_status to check lock through either interrupt values
or directly by the call back.
When the device is not streaming the frontends original call back is
used. When streaming has started it turns off I2C messaging by
setting st->i2c_talk_onoff to zero. I2C can only be turn on again
by one of the other allowed frontend calls.
All old code is removed from lme2510_msg and this function only needs
to set st->i2c_talk_onoff to 1.
The lock status is saved and when the frondend is locked is maintained
by lme2510_int_response who will now just kill the lock.
The call back for rs2000 tuner is nologer required.
All frontend types have been tested.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Create call backs dm04_read_signal_strength, dm04_read_snr and
move dm04_read_ber and dm04_read_ucblocks for all frontends
Removing the I2C filtering from lme2510_msg and the old rs2000 callbacks.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A quirk of some older firmwares that report endpoint pipe type as PIPE_BULK
but the endpoint otheriwse functions as interrupt.
Check if usb_endpoint_type is USB_ENDPOINT_XFER_BULK and set as usb_rcvbulkpipe.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Ocassionally the device fails to report back an interrupt urb status which
results in false no lock trigger on the RS2000 demodulator.
Increase time from 60 msecs to 200 msecs.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
X-Patchwork-Delegate: m.chehab@samsung.com
Fix the following smatch warning:
drivers/media/pci/cx88//cx88-dvb.c:1508 dvb_register() warn: if statement not indented
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The 'ARM: OMAP3: legacy clock data move under clk driver' patch series
causes build errors when CONFIG_OMAP3 is not set:
drivers/clk/ti/dpll.c: In function 'ti_clk_register_dpll':
drivers/clk/ti/dpll.c:199:31: error: 'omap3_dpll_ck_ops' undeclared (first use in this function)
const struct clk_ops *ops = &omap3_dpll_ck_ops;
^
drivers/clk/ti/dpll.c:199:31: note: each undeclared identifier is reported only once for each function it appears in
drivers/clk/ti/dpll.c:259:10: error: 'omap3_dpll_per_ck_ops' undeclared (first use in this function)
ops = &omap3_dpll_per_ck_ops;
^
drivers/built-in.o: In function `ti_clk_register_gate':
drivers/clk/ti/gate.c:179: undefined reference to `clkhwops_omap3430es2_dss_usbhost_wait'
drivers/clk/ti/gate.c:179: undefined reference to `clkhwops_am35xx_ipss_module_wait'
-in.o: In function `ti_clk_register_interface':
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_omap3430es2_iclk_hsotgusb_wait'
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_omap3430es2_iclk_dss_usbhost_wait'
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_omap3430es2_iclk_ssi_wait'
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_am35xx_ipss_wait'
drivers/built-in.o: In function `ti_clk_register_composite':
:(.text+0x3da768): undefined reference to `ti_clk_build_component_gate'
In order to fix that problem, this patch makes the omap3 legacy code
compiled only when both CONFIG_OMAP3 and CONFIG_ATAGS are set.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
As complained by smatch:
drivers/media/usb/dvb-usb-v2/rtl28xxu.c:1159 rtl2832u_tuner_attach() info: 'pdata' is not actually initialized (unreached code).
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/rtl2832.c:157:5: warning: no previous prototype for ‘rtl2832_bulk_write’ [-Wmissing-prototypes]
int rtl2832_bulk_write(struct i2c_client *client, unsigned int reg,
^
drivers/media/dvb-frontends/rtl2832.c:169:5: warning: no previous prototype for ‘rtl2832_update_bits’ [-Wmissing-prototypes]
int rtl2832_update_bits(struct i2c_client *client, unsigned int reg,
^
drivers/media/dvb-frontends/rtl2832.c:181:5: warning: no previous prototype for ‘rtl2832_bulk_read’ [-Wmissing-prototypes]
int rtl2832_bulk_read(struct i2c_client *client, unsigned int reg, void *val,
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/rtl2830.c:21:5: warning: no previous prototype for ‘rtl2830_bulk_write’ [-Wmissing-prototypes]
int rtl2830_bulk_write(struct i2c_client *client, unsigned int reg,
^
drivers/media/dvb-frontends/rtl2830.c:33:5: warning: no previous prototype for ‘rtl2830_update_bits’ [-Wmissing-prototypes]
int rtl2830_update_bits(struct i2c_client *client, unsigned int reg,
^
drivers/media/dvb-frontends/rtl2830.c:45:5: warning: no previous prototype for ‘rtl2830_bulk_read’ [-Wmissing-prototypes]
int rtl2830_bulk_read(struct i2c_client *client, unsigned int reg, void *val,
^
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
