When receiving and processing extended next pages the base registers
were used instead of the XNP registers. Update the code to use the
device XNP and link partner XNP registers.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advertise and apply the Forward Error Correction capabilities of the
device based on the FEC ability of the device. Also, remove the use
of some hard coded values related to KR and FEC in preference of some
#defines.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The auto negotiation logic was geared to being the initiator of the
auto negotiation. This presented problems when auto negotiation was
initiated by the remote end. Change the auto negotiation logic to
make use of the auto negotiation event interrupt thus allowing the
auto negotiation state machine to function properly in either scenario.
This also removes the polling during auto-negotiation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the Tx ring cleanup can run at the same time that data is being
transmitted, a spin lock was used to protect the ring. This patch
eliminates the need for Tx spinlocks by updating the current ring
position only after all ownership bits for data being transmitted have
been set. This will insure that ring operations in the Tx cleanup path
do not interfere with the ring operations in the Tx transmit path.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the Rx descriptor ring processing similar to the Tx descriptor
ring processing. Remove the realloc_index and realloc_threshold
variables and base everything on the current index counter and the
dirty index counter.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When performing a device restart, like during an MTU change, sometimes
the device queues still have data and get hung up trying to flush
resulting in the device becoming unresponsive until brought down and
back up. To prevent this, always perform a device reset during a
restart.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reads to registers are undefined when the PCS is powered down. To be
safe, save the CTRL1 register used for power down during suspend and
restore that value during resume.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The amd-xgbe driver relies on the amd-xgbe-phy phylib driver. Add a
check to be sure that if any errors occur during probing of the
amd-xgbe-phy driver then the amd-xgbe driver returns an error.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This set of patches resolves some checks reported by the checkpatch
tool.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This set of patches resolves some checks reported by the checkpatch
tool.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The arm-cci driver completes the probe sequence even if the cci node is
marked as disabled. Add a check in the driver to honour the cci status
in the device tree.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
null_blk is partitionable, but it doesn't store any of the info. When
it is loaded, you would normally see:
[1226739.343608] nullb0: unknown partition table
[1226739.343746] nullb1: unknown partition table
which can confuse some people. Add the appropriate gendisk flag
to suppress this info.
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull char/misc driver fixes from Greg KH:
"Here are three small driver fixes for reported issues for 3.19-rc5.
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mcb: mcb-pci: Only remap the 1st 0x200 bytes of BAR 0
mei: add ABI documentation for fw_status exported through sysfs
mei: clean reset bit before reset
Pull tty/serial driver fixes from Greg KH:
"Here are some tty and serial driver fixes for 3.19-rc5 that resolve
some reported issues, and add a new device id to the 8250 serial port
driver.
All have been in linux-next with no reported problems"
* tag 'tty-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: samsung: Add the support for Exynos5433 SoC
Revert "tty: Fix pty master poll() after slave closes v2"
tty: Prevent hw state corruption in exclusive mode reopen
tty: Add support for the WCH384 4S multi-IO card
serial: fix parisc boot hang
Pull staging driver fixes from Greg KH:
"Here are 6 staging driver fixes for 3.19-rc5.
They fix some reported issues with some IIO drivers, as well as some
issues with the vt6655 wireless driver.
All have been in linux-next for a while"
* tag 'staging-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vt6655: fix sparse warning: argument type
staging: vt6655: Fix loss of distant/weak access points on channel change.
staging: vt6655: vnt_tx_packet Fix corrupted tx packets.
staging: vt6655: fix sparse warnings: incorrect argument type
iio: iio: Fix iio_channel_read return if channel havn't info
iio: ad799x: Fix ad7991/ad7995/ad7999 config setup
Pull USB fixes from Greg KH:
"Here is a bunch of USB fixes for 3.19-rc5.
Most of these are gadget driver fixes, along with the xhci driver fix
that we both reported having problems with, as well as some new device
ids and other tiny fixes.
All have been in linux-next with no problems"
* tag 'usb-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (43 commits)
usb: dwc3: gadget: Stop TRB preparation after limit is reached
usb: dwc3: gadget: Fix TRB preparation during SG
usb: phy: mv-usb: fix usb_phy build errors
usb: serial: handle -ENODEV quietly in generic_submit_read_urb
usb: serial: silence all non-critical read errors
USB: console: fix potential use after free
USB: console: fix uninitialised ldisc semaphore
usb: gadget: udc: atmel: fix possible oops when unloading module
usb: gadget: gadgetfs: fix an oops in ep_write()
usb: phy: Fix deferred probing
OHCI: add a quirk for ULi M5237 blocking on reset
uas: Add US_FL_NO_ATA_1X for 2 more Seagate disk enclosures
uas: Do not blacklist ASM1153 disk enclosures
usb: gadget: udc: avoid dereference before NULL check in ep_queue
usb: host: ehci-tegra: request deferred probe when failing to get phy
uas: disable UAS on Apricorn SATA dongles
uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS566 with usb-id 0bc2:a013
uas: Add US_FL_NO_ATA_1X for Seagate devices with usb-id 0bc2:a013
xhci: Add broken-streams quirk for Fresco Logic FL1000G xhci controllers
USB: EHCI: adjust error return code
...
As Skyhawk and BE3-R (both multi-function devices) don't advertise the
PCI-ACS capability, the vfio driver places all the functions of these
devices in a single IOMMU group. Attaching (via PCI-passthru) two
different Skyhawk/BE3-R partitions (nPAR, Flex, etc. PFs) using vfio, to
different guests doesn't work as vfio only allows functions in *different*
IOMMU groups to be assigned to different guests.
As peer-to-peer access between PFs in Skyhawk/BE3-R is not possible, we can
treat them as "fully isolated" even though the device doesn't advertise
ACS. Add a PCI quirk for Skyhawk and BE3-R chips to fix this problem.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Some AMD/ATI GPUs report NoSoftRst- to indicate that they perform a reset
when software transitions them from D3hot to D0, but there is no apparent
effect on the device: the monitor remains synced and the framebuffer
contents are retained.
Callers of pci_reset_function() don't necessarily have a way to validate
whether a reset was effective, so we don't want to rely on NoSoftRst if
it's known to be inaccurate. Returning an error in such cases appears to
be the better option. For users like vfio-pci, this allows the driver to
escalate to the bus reset interfaces.
If a device lives on the root bus, there's really no further
escalation path, so we exempt PM reset as potentially better than
nothing.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Per the PCI Power Management spec r1.2, sec 3.2.4, a device that advertises
No_Soft_Reset == 0 in the PMCSR register (reported by lspci as "NoSoftRst-")
should perform an internal reset when transitioning from D3hot to D0 via
software control. Configuration context is lost and the device requires a
full reinitialization sequence.
Unfortunately the definition of "internal reset", beyond the application of
the configuration context, is largely left to the interpretation of the
specific device. Some devices don't seem to perform an "internal reset"
even if they report No_Soft_Reset == 0.
We still need to honor the PCI specification and restore PCI config context
in the event that we do a PM reset, so we don't cache and modify the
PCI_PM_CTRL_NO_SOFT_RESET bit for the device, but for interfaces where the
intention is to reset the device, like pci_reset_function(), we need a
mechanism to flag that PM reset (a D3hot->D0 transition) doesn't perform
any significant "internal reset" of the device.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Every PCI-PCI bridge window should fit inside an upstream bridge window
because orphaned address space is unreachable from the primary side of the
upstream bridge. If we inherit invalid bridge windows that overlap an
upstream window from firmware, clip them to fit and update the bridge
accordingly.
[bhelgaas: changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: "James E.J. Bottomley" <jejb@parisc-linux.org>
CC: Helge Deller <deller@gmx.de>
CC: linux-parisc@vger.kernel.org
Add pci_claim_bridge_resource() to claim a PCI-PCI bridge window. This is
like regular pci_claim_resource(), except that if we fail to claim the
window, we check to see if we can reduce the size of the window and try
again.
This is for scenarios like this:
pci_bus 0000:00: root bus resource [mem 0xc0000000-0xffffffff]
pci 0000:00:01.0: bridge window [mem 0xbdf00000-0xddefffff 64bit pref]
pci 0000:01:00.0: reg 0x10: [mem 0xc0000000-0xcfffffff pref]
The 00:01.0 window is illegal: it starts before the host bridge window, so
we have to assume the [0xbdf00000-0xbfffffff] region is inaccessible. We
can make it legal by clipping it to [mem 0xc0000000-0xddefffff 64bit pref].
Previously we discarded the 00:01.0 window and tried to reassign that part
of the hierarchy from scratch. That is a problem because Linux doesn't
always assign things optimally. For example, in this case, BIOS put the
01:00.0 device in a prefetchable window below 4GB, but after 5b28541552,
Linux puts the prefetchable window above 4GB where the 32-bit 01:00.0
device can't use it.
Clipping the 00:01.0 window is less intrusive than completely reassigning
things and is sufficient to let us use most of the BIOS configuration. Of
course, it's possible that devices below 00:01.0 will no longer fit. If
that's the case, we'll have to reassign things. But that's a separate
problem.
[bhelgaas: changelog, split into separate patch]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.16+
Add pci_bus_clip_resource(). If a PCI-PCI bridge window overlaps an
upstream bridge window but is not completely contained by it, this clips
the downstream window so it fits inside the upstream one.
No functional change (this adds the function but no callers).
[bhelgaas: changelog, split into separate patch]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.16+
pci_setup_bridge_io(), pci_setup_bridge_mmio(), and
pci_setup_bridge_mmio_pref() program the windows of PCI-PCI bridges.
Previously they accepted a pointer to the pci_bus of the secondary bus,
then looked up the bridge leading to that bus. Pass the bridge directly,
which will make it more convenient for future callers.
No functional change.
[bhelgaas: changelog, split into separate patch]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.16+
Reports against the TL-WDN4800 card indicate that PCI bus reset of this
Atheros device cause system lock-ups and resets. I've also been able to
confirm this behavior on multiple systems. The device never returns from
reset and attempts to access config space of the device after reset result
in hangs. Blacklist bus reset for the device to avoid this issue.
[bhelgaas: This regression appeared in v3.14. Andreas bisected it to
425c1b223d ("PCI: Add Virtual Channel to save/restore support"), but we
don't understand the mechanism by which that commit affects the reset
path.]
[bhelgaas: changelog, references]
Link: http://lkml.kernel.org/r/20140923210318.498dacbd@dualc.maya.org
Reported-by: Andreas Hartmann <andihartmann@freenet.de>
Tested-by: Andreas Hartmann <andihartmann@freenet.de>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
Enable a mechanism for devices to quirk that they do not behave when
doing a PCI bus reset. We require a modest level of spec compliant
behavior in order to do a reset, for instance the device should come
out of reset without throwing errors and PCI config space should be
accessible after reset. This is too much to ask for some devices.
Link: http://lkml.kernel.org/r/20140923210318.498dacbd@dualc.maya.org
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
No board file instantiates the IPMMU using platform data. Now that we
have DT support, get rid of platform data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Devices such as the system DMA controller are connected to multiple
micro TLBs of the same IOMMU. Support this.
Selective enabling of micro TLBs based on runtime device usage isn't
possible at the moment due to lack of support in the IOMMU and DMA
mapping APIs. Support for devices connected to different IOMMUs is also
unsupported for the same reason.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Make platform data optional when the device is instantiated from DT and
look up the micro-TLB number in the bus master DT node.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The TLB must be invalidated after unmapping memory to remove stale TLB
entries. this was supposed to be performed already, but a bug in the
driver prevented the TLB invalidate function from being called. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
When clearing PUD or PMD entries the child page table (if any) is freed
and the PUD or PMD entry is then cleared. This result in a small race
condition window during which a free page table could be accessed by the
IPMMU.
Fix it by clearing and flushing the PUD or PMD entry before freeing the
child page table.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The ARM IOMMU mapping needs to be released when attaching the device
fails. Add arm_iommu_release_mapping() to the error code path. This is
safe to call with a NULL mapping, so no specific check is needed.
Cleanup is also missing when failing to create a mapping. Jump to the
error code path in that case instead of returning immediately.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add parsing and reporting of iSCSI capability for a given device or
function.
Also add support for iSCSI partition type with DCB in NPAR mode.
In this mode it is expected that software would configure both the LAN
and iSCSI traffic classes for the iSCSI partition; whereas all the NIC
type partitions will use LAN TC (TC0) only.
Hence, the patch enables querying of DCB configuration in MFP mode and
configures TCs for iSCSI partition type.
Though NIC type partitions may not have more than 1 TC enabled for them
the port may have multiple TCs enabled and hence I40E_FLAG_DCB_ENABLED
will be set/reset on all the partitions based on number of TCs on the
port. This is required as in DCB environment it is expected that all
traffic will be priority tagged.
Change-ID: I8c6e1cfd46c46d8a39c57d9020d9ff8d42ed8a7d
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of leaving the Rx timestamps in the same mode as before if we
disable the Rx logic, we can set it into a mode that has the fewest
possible timestamps generated. To do this, select only V1 mode, but do
not enable UDP packet recognition. This should eliminate all (or at
least almost all) Rx timestamps, since V1 packets are always over UDP.
Change-ID: If847288e0030a716e059c4c33ab114f2cf038f05
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It's possible that the user configured only Tx hardware timestamping,
and thus we might be receiving PTP traffic which we timestamp but which
software never reads. In this case we don't want to check for Rx
timestamp hang, because we already know that software won't be handling
them. Thus, we add the same check against pf->ptp_rx as we have in the
Rx timestamp code path.
Change-ID: I66486c8dba307facbff8eace4e52e2f083789d1b
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This commit adds support for multiple hardware chip selects to spi-orion.
Different SoCs support different number of chip selects (up to
8 on some platforms). The driver allows up to this number, and it is up
to the implementer to only use the chip selects that are available.
Signed-off-by: Ken Wilson <ken.wilson@opengear.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add struct size checks to many of the indirect structs and a few
command structs that were left out previously.
Change-ID: I7810b9af0f04e3ced670639f8671daf7df9b3f4d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Disable firmware LLDP agent for NICs with firmware version lower than
v4.3. Added a message when driver disables the firmware LLDP agent on
such NICs.
Change-ID: Ia8abf89439c70cb50e23db82753d7d282265506b
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We should not be doing Tx or Rx timestamps if we do not have PTP
enabled. Add checks to ensure that we don't attempt to handle any PTP
related timestamping code if we have not enabled PTP on that PF.
Change-ID: I4335942ae2d5c5f91abfdbeeea02bcace49e7677
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We should not blindly enable the PTP interrupt flags for all PFs. We
should only enable the PTP interrupt in PFs which have enabled
PTP.
Change-ID: I051a17cae4c199a2f3cf7852266e27eda6630525
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Dump Stats string has been removed from functional debugfs
help message. Now it does not show up when we echo command to
debugfs/Fortville queue.
Change-ID: I9333473826b574f1afa6ddb785fd7adfbdcb2884
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
