Let's introduce a compute_config() helper for fixed mode panels.
For now all it does is the fixed_mode->adjusted_mode copy.
Note that with sDVO we have to ask the external encoder chip
to spit out our actual display timings for us, so the fixed_mode
to adjusted_mode copy done by intel_panel_compute_config() is
redundant, but we still want to use it to do other checks for us
later. We'll be fine so long as we only call it before
intel_sdvo_get_preferred_input_mode() overwrites adjusted_mode
with the timings from the encoder.
v2: Use intel_panel_compute_config() with sDVO
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210927185207.13620-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
All fixed mode panels should behave the same way when it comes to mode
filtering. Reuse the intel_panel_mode_valid() for all of them.
This changes the behaviour to match what we do for eDP, ie.
reject anything that doesn't exactly match the fixed mode
dimensions. Users can still manually provide different
sized modes which will be handled by the panel fitter just
as before. The difference is that we can no longer report
funny modes in the connector's mode list.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210923200109.4459-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The PHY ownership release->AUX PW disable steps during a modeset
disable->PHY disconnect sequence can hang the system if the PHY
disconnect happens after disabling the PHY's PLL. The spec doesn't
require a specific order for these two steps, so this issue is still
being root caused by HW/FW teams. Until that is found, let's make
sure the disconnect happens before the PLL is disabled, and do this on
all platforms for consistency.
v2: Add a TODO comment to remove the w/a once the issue is root
caused/fixed. (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-7-imre.deak@intel.com
So far TC-cold was blocked only for the duration of TypeC mode resets.
The DP-alt and legacy modes require TC-cold to be blocked also whenever
the port is in use (AUX transfers, enable modeset), and this was ensured
by the held PHY ownership flag. On ADL-P this doesn't work, since the
PHY ownership flag is in a register backed by the PW#2 power well.
Whenever this power well is disabled the ownership flag is cleared by
the HW under the driver.
The only way to cleanly release and re-acquire the PHY ownership flag
and also allow for power saving (by disabling the display power wells
and reaching DC5/6 states) is to hold the TC-cold blocking power domains
while the PHY is connected and disconnect/reconnect the PHY on-demand
around AUX transfers and modeset enable/disables. Let's do that,
disconnecting a PHY with a 1 sec delay after it becomes idle. For
consistency do this on all platforms and TypeC modes.
v2: Add tc_mode!=disconnected and phy_is_owned asserts to
__intel_tc_port_lock().
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-6-imre.deak@intel.com
While a TypeC port mode is locked a DISPLAY_CORE power domain reference
is held, which implies a runtime PM ref. By removing the ICL !legacy
port special casing, a TC_COLD_OFF power domain reference will be taken
for such ports, which also translates to a runtime PM ref on that
platform. A follow-up change will stop holding the DISPLAY_CORE power
domain while the port is locked.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-11-imre.deak@intel.com
For the ADL-P TBT mode the spec doesn't require blocking TC-cold by
using the legacy AUX power domain. To avoid the timeouts that this would
cause during PHY disconnect/reconnect sequences (which will be more
frequent after a follow-up change) use the TC_COLD_OFF power domain in
TBT mode on all platforms. On TGL this power domain blocks TC-cold via a
PUNIT command, while on other platforms the domain just takes a runtime
PM reference.
If the HPD live status indicates that the port mode needs to be reset
- for instance after switching from TBT to a DP-alt sink - still take
the AUX domain, since the IOM firmware handshake requires this.
v2: Rebased on v2 of the previous patch.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-5-imre.deak@intel.com
A follow-up change will start to disconnect/re-connect PHYs around AUX
transfers and modeset enable/disables. To prepare for that add a new
TypeC PHY disconnected mode, to help tracking the TC-cold blocking power
domain status (no power domain in disconnected state, mode dependent
power domain in connected state).
v2: Move the !disconnected mode and phy-owned asserts in
__intel_tc_port_lock() later in the patchset, when the asserts will
hold. (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-3-imre.deak@intel.com
A follow-up patch will disconnect/reconnect PHYs around AUX transfers
and modeset enable/disables. To prepare for that and make things
consistent for all TypeC modes stop connecting the PHY in legacy mode
without a sink being connected. This was done before since in legacy
mode the PHY is dedicated to display usage, so there was no point in
disconnecting it. However after the follow-up changes the TC-cold
blocking power domains will be held as long as the PHY is in the
connected state, so we'll need to disconnect/re-connect the PHY in all
TypeC modes to allow for power saving.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-7-imre.deak@intel.com
On ADL-P the PHY ready/complete flag is always set even in TBT-alt mode.
To avoid taking the PHY ownership and the following spurious "PHY sudden
disconnect" messages on this platform when connecting the PHY in TBT
mode, check if there is any DP-alt or legacy sink connected before
taking the ownership.
v2: (Jose)
- Fix debug message clarifying that a TBT sink can be connected.
- Add comments describing the PHY complete HW flag semantic differences
between adl-p and other platforms.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-2-imre.deak@intel.com
Waiting for the PHY complete flag to clear when releasing the PHY
ownership was add in
commit ddec362724 ("drm/i915: Wait for TypeC PHY complete flag to clear in safe mode")
This isn't required by the spec, the vague idea was to make the
handshake with the firmware more robust, without actual evidence for
when it would be needed. Checking this again, the flag doesn't clear on
ICL until after the PHY's PLL is disabled and the flag is permanently
set on ADL-P. To avoid the spurious timeout messages in dmesg, just
remove this wait.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-4-imre.deak@intel.com
Display underrun in HDR mode when cursor is enabled.
RTL fix will be implemented CLKGATE_DIS_PSL_A bit 28-46520h.
As per W/A 1604331009, Disable cursor clock gating in HDR mode.
Bspec : 33451
Changes since V6:
- Address checkpatch warnings
- Bit ordering
Changes since V5:
- replace intel_de_read with intel_de_rmw - Jani
Changes since V4:
- Added WA needed check - Ville
- Replace BIT with REG_BIT - Ville
- Add WA enable/disable support back which was
added in V1 - Ville
Changes since V3:
- Disable WA when not in HDR mode or cursor plane
not active - Ville
- Extract required args from crtc_state - Ville
- Create HDR mode API using bdw_set_pipemisc ref - Ville
- Tested with HDR video as well full setmode, WA
applies and disables
Changes since V2:
- Made it general gen11 WA
- Removed WA needed check
- Added cursor plane active check
- Once WA enable, software will not disable
Changes since V1:
- Modified way CLKGATE_DIS_PSL bit 28 was modified
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929052442.2543054-1-tejaskumarx.surendrakumar.upadhyay@intel.com
On FBC1 we can specify an arbitrary cfb stride. The hw will
simply throw away any compressed line that would exceed the
specified limit and keep using the uncompressed data instead.
Thus we can allow arbitrary compression limits.
The one thing we have to keep in mind though is that the cfb
stride is specified in units of 32B (gen2) or 64B (gen3+).
Fortunately X-tile is already 128B (gen2) or 512B (gen3+) wide
so as long as we limit outselves to the same 4x compression
limit that FBC2 has we are guaranteed to have a sufficiently
aligned cfb stride.
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921152517.803-5-ville.syrjala@linux.intel.com
