The firmware does not respond ARP request and causes ping failure with
following steps:
1. Bring up interface
ifconfig wlan0 up or start wpa_supplicant
2. Set the IP address
ifconfig wlan0 192.168.100.10
3. Bring down interface or
ifconfig wlan0 down or kill wpa_supplicant
4. Bring up interface again and set the same IP address
5. Connect to AP(192.168.100.1) and ping to AP will be failed.
FMAC clears arp_hostip when bringing down the interface, but not set it
back if setting the same IP address. We are able to see the IP address
in interface info(inconfig wlan0) but the ping still cannot work because
the firmware ARP offload does not respond the ARP request.
Because of that, we remove "arp_hostip_clear" from function
"brcmf_netdev_stop"
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-3-git-send-email-chi-hsien.lin@cypress.com
First set of iwlwifi patches intended for v5.8
* TX queue debugfs improvements;
* Support for a few new FW API versions;
* Remove deprecated scan FW API version;
* New hw configs and other related changes;
* Support for NPK buffers in debugging;
* More debugging fetures;
* Some other small fixes and clean-ups;
# gpg: Signature made Fri 24 Apr 2020 04:39:43 PM EEST using RSA key ID 1A3CC5FA
# gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>"
# gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
sparse warnings: (new ones prefixed by >>)
>> drivers/net/wireless/realtek/rtw88/mac.c:653:5: sparse: sparse:
symbol '__rtw_download_firmware' was not declared. Should it be static?
>> drivers/net/wireless/realtek/rtw88/mac.c:817:5: sparse: sparse:
symbol '__rtw_download_firmware_legacy' was not declared. Should it be
static?
Fixes: 15d2fcc6b2 ("rtw88: add legacy firmware download for 8723D devices")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424101255.28239-1-yhchuang@realtek.com
TX FIFO size is 32k and it was divided into 256 pages with 128 bytes.
A boundary is used to split pages into two parts, head part is used to
store TX packets coming from host, and tail part is reserved for special
purposes, such as beacon packet, null data packet and so on.
The TX packets coming from host have many categories, such as VO, VI, BE,
BK, MG and etc. When going into head part of TX FIFO, they are classified
to four priority queue named low, normal, high and extra priority queues.
Each priority queue occupies predefined number of page, if a certain
priority queue is full, TX packet will store into PUB priority queue.
Similarly, RX FIFO is 16k and split into two parts, head part is used to
store RX packets, and tail part is 128 bytes and used to store report.
Thus, we fill this boundary to register as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422034607.28747-8-yhchuang@realtek.com
The power polling command is one kind of power sequence commands. It's used
to check hardware situation, and subsequent comamnds will be executed if
hardware is ready. A special case is PCIE must toggle BIT_PFM_WOWL and try
again if first try is failed.
In order to reduce indentation to understand the code easier, move polling
part to a separate function. Then, the 'while (1)...loop' is replaced by
two statements to do first try and retry.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422034607.28747-5-yhchuang@realtek.com
The mac power-on flow consists of three steps:
1. pre_sys_cfg (Before switching power state)
2. power_switch (Switching power state)
3. init_sys_cfg (Settings after swtiching power state)
When switching power state, driver will load and parse the power sequence
tables. For 8723D devices, the logics for parsing are most same except for
the polling function. 8723D devices need to toggle BIT_PFM_WOWL twice.
The settings after power state is switched for 8723D devices are quite
different with other devices, extract a legacy function for them.
For power-off flow, 8723D devices have the same logic with existing chips.
But warning printed if we run power-off sequence in power-off state:
rtw_pci 0000:03:00.0: failed to poll offset=0x5f8 mask=0xff value=0x0
The scenario is user do 'ifconfig up' that will run power-on sequence to
bring up and then run power-off sequence to enter idle
(IEEE80211_CONF_IDLE). Then, user do 'ifconfig down' that will run
power-off sequence again, and the warning is shown. Original code check
power-on state to avoid to run power-on sequence twice, and this commit
extends to check both power-on and power-off states.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422034607.28747-4-yhchuang@realtek.com
The WLAN CPU of 8723D device is different from others, add legacy
firmware download function for it. A new variable wlan_cpu is used to
decide which firmware download function we should use.
Legacy firmware file contains 32 bytes header including version and
subversion. When downloading to wlan cpu, header is excluded.
Firmware is downloaded via beacon queue to reserved page that is a part of
TX buffer. Since 11N WLAN CPU uses different control registers, this patch
introduces related control registers.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422034607.28747-2-yhchuang@realtek.com
8723D use SIPI to indirectly read RF register instead of directly read,
so introduce a new struct rtw_rf_sipi_addr and new function
rtw_phy_read_rf_sipi(). Since other chips don't use the new function,
only 8723D needs to fill struct rtw_rf_sipi_addr in rtw_chip_info.
Because there are two kinds of functions for reading RF registers now,
change rtw_phy_read_rf() to chip->ops->read_rf() in
rtw_phy_write_rf_reg_sipi() so that we can switch tp proper RF read
functions depends on the type of the chip.
Though 8723D is an 1x1 chip, it has two RF PHY and we can switch to
one of them, and that should be configured properly. Hence, add a
fix_rf_phy_num to struct rtw_chip_info to allow driver to set one of
the PHY's registers for 8723D, even it is only 1x1. Another variable
rf_phy_num is introduced to keep the constraint number of RF path we
can access, and its value is:
rf_phy_num = (fix_rf_phy_num ? fix_rf_phy_num : rf_path_num)
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420055054.14592-5-yhchuang@realtek.com
8723D doesn't support beamform because rtw88 only supports VHT beamform
but 8723d doesn't have VHT capability. Though 8723d doesn't support
beamform, BSS_CHANGED_MU_GROUPS is still marked as changed when doing
disassociation. So, add wrapper functions for all beamform ops to make
sure they aren't NULL before calling.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420055054.14592-3-yhchuang@realtek.com
