[ Upstream commit 21431f70f6 ]
[Why]
We're only setting the flags on stream[0]'s planes so this logic fails
if we have more than one stream in the state.
This can cause a page flip timeout with multiple displays in the
configuration.
[How]
Index into the stream_status array using the stream index - it's a 1:1
mapping.
Fixes: cdaae8371a ("drm/amd/display: Handle GPU reset for DC block")
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6eff272dbe ]
[Why]
The HW interrupt gets disabled after GPU reset so we don't receive
notifications for HPD or AUX from DMUB - leading to timeout and
black screen with (or without) DPIA links connected.
[How]
Re-enable the interrupt after GPU reset like we do for the other
DC interrupts.
Fixes: 81927e2808 ("drm/amd/display: Support for DMUB AUX")
Reviewed-by: Jude Shih <Jude.Shih@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cefcf24b4d ]
Commit 39fbef4b0f ("PM: hibernate: Get block device exclusively in
swsusp_check()") changed the opening mode of the block device to
(FMODE_READ | FMODE_EXCL).
In the corresponding calls to swsusp_close(), the mode is still just
FMODE_READ which triggers the warning in blkdev_flush_mapping() on
resume from hibernate.
So, use the mode (FMODE_READ | FMODE_EXCL) also when closing the
device.
Fixes: 39fbef4b0f ("PM: hibernate: Get block device exclusively in swsusp_check()")
Signed-off-by: Thomas Zeitlhofer <thomas.zeitlhofer+lkml@ze-it.at>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac13285214 ]
Update NC-SI command handler (both standard and OEM) to take into
account of payload paddings in allocating skb (in case of payload
size is not 32-bit aligned).
The checksum field follows payload field, without taking payload
padding into account can cause checksum being truncated, leading to
dropped packets.
Fixes: fb4ee67529 ("net/ncsi: Add NCSI OEM command support")
Signed-off-by: Kumar Thangavel <thangavel.k@hcl.com>
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94902d849e ]
As Vincent reports in:
https://lore.kernel.org/r/20211118163417.21617-1-vincent.whitchurch@axis.com
The put_user() in schedule_tail() can get stuck in a livelock, similar
to a problem recently fixed on riscv in commit:
285a76bb2c ("riscv: evaluate put_user() arg before enabling user access")
In __raw_put_user() we have a critical section between
uaccess_ttbr0_enable() and uaccess_ttbr0_disable() where we cannot
safely call into the scheduler without having taken an exception, as
schedule() and other scheduling functions will not save/restore the
TTBR0 state. If either of the `x` or `ptr` arguments to __raw_put_user()
contain a blocking call, we may call into the scheduler within the
critical section. This can result in two problems:
1) The access within the critical section will occur without the
required TTBR0 tables installed. This will fault, and where the
required tables permit access, the access will be retried without the
required tables, resulting in a livelock.
2) When TTBR0 SW PAN is in use, check_and_switch_context() does not
modify TTBR0, leaving a stale value installed. The mappings of the
blocked task will erroneously be accessible to regular accesses in
the context of the new task. Additionally, if the tables are
subsequently freed, local TLB maintenance required to reuse the ASID
may be lost, potentially resulting in TLB corruption (e.g. in the
presence of CnP).
The same issue exists for __raw_get_user() in the critical section
between uaccess_ttbr0_enable() and uaccess_ttbr0_disable().
A similar issue exists for __get_kernel_nofault() and
__put_kernel_nofault() for the critical section between
__uaccess_enable_tco_async() and __uaccess_disable_tco_async(), as the
TCO state is not context-switched by direct calls into the scheduler.
Here the TCO state may be lost from the context of the current task,
resulting in unexpected asynchronous tag check faults. It may also be
leaked to another task, suppressing expected tag check faults.
To fix all of these cases, we must ensure that we do not directly call
into the scheduler in their respective critical sections. This patch
reworks __raw_put_user(), __raw_get_user(), __get_kernel_nofault(), and
__put_kernel_nofault(), ensuring that parameters are evaluated outside
of the critical sections. To make this requirement clear, comments are
added describing the problem, and line spaces added to separate the
critical sections from other portions of the macros.
For __raw_get_user() and __raw_put_user() the `err` parameter is
conditionally assigned to, and we must currently evaluate this in the
critical section. This behaviour is relied upon by the signal code,
which uses chains of put_user_error() and get_user_error(), checking the
return value at the end. In all cases, the `err` parameter is a plain
int rather than a more complex expression with a blocking call, so this
is safe.
In future we should try to clean up the `err` usage to remove the
potential for this to be a problem.
Aside from the changes to time of evaluation, there should be no
functional change as a result of this patch.
Reported-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20211118163417.21617-1-vincent.whitchurch@axis.com
Fixes: f253d827f3 ("arm64: uaccess: refactor __{get,put}_user")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20211122125820.55286-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 102110efdf ]
Current nvmet_try_send_ddgst() code does not check whether
all data digest bytes are transmitted, fix this by returning
-EAGAIN if all data digest bytes are not transmitted.
Fixes: 872d26a391 ("nvmet-tcp: add NVMe over TCP target driver")
Signed-off-by: Varun Prakash <varun@chelsio.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd23f02f16 ]
Commit fbdc21e9b0 ("cpufreq: intel_pstate: Add Icelake servers
support in no-HWP mode") enabled the use of Intel P-State driver
for Ice Lake servers.
But it doesn't cover the case when OS can't control P-States.
Therefore, for Ice Lake server, if MSR_MISC_PWR_MGMT bits 8 or 18
are enabled, then the Intel P-State driver should exit as OS can't
control P-States.
Fixes: fbdc21e9b0 ("cpufreq: intel_pstate: Add Icelake servers support in no-HWP mode")
Signed-off-by: Adamos Ttofari <attofari@amazon.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b1b62bc1e ]
Currently mvpp2_xdp_setup won't allow attaching XDP program if
mtu > ETH_DATA_LEN (1500).
The mvpp2_change_mtu on the other hand checks whether
MVPP2_RX_PKT_SIZE(mtu) > MVPP2_BM_LONG_PKT_SIZE.
These two checks are semantically different.
Moreover this limit can be increased to MVPP2_MAX_RX_BUF_SIZE, since in
mvpp2_rx we have
xdp.data = data + MVPP2_MH_SIZE + MVPP2_SKB_HEADROOM;
xdp.frame_sz = PAGE_SIZE;
Change the checks to check whether
mtu > MVPP2_MAX_RX_BUF_SIZE
Fixes: 07dd0a7aae ("mvpp2: add basic XDP support")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4e9bfb7c9 ]
Calling ipa_cmd_pipeline_clear() after stopping the channel
underlying the AP<-modem RX endpoint can lead to a deadlock.
This occurs in the ->runtime_suspend device power operation for the
IPA driver. While this callback is in progress, any other requests
for power will block until the callback returns.
Stopping the AP<-modem RX channel does not prevent the modem from
sending another packet to this endpoint. If a packet arrives for an
RX channel when the channel is stopped, an SUSPEND IPA interrupt
condition will be pending. Handling an IPA interrupt requires
power, so ipa_isr_thread() calls pm_runtime_get_sync() first thing.
The problem occurs because a "pipeline clear" command will not
complete while such a SUSPEND interrupt condition exists. So the
SUSPEND IPA interrupt handler won't proceed until it gets power;
that won't happen until the ->runtime_suspend callback (and its
"pipeline clear" command) completes; and that can't happen while
the SUSPEND interrupt condition exists.
It turns out that in this case there is no need to use the "pipeline
clear" command. There are scenarios in which clearing the pipeline
is required while suspending, but those are not (yet) supported
upstream. So a simple fix, avoiding the potential deadlock, is to
stop calling ipa_cmd_pipeline_clear() in ipa_endpoint_suspend().
This removes the only user of ipa_cmd_pipeline_clear(), so get rid
of that function. It can be restored again whenever it's needed.
This is basically a manual revert along with an explanation for
commit 6cb63ea6a3 ("net: ipa: introduce ipa_cmd_tag_process()").
Fixes: 6cb63ea6a3 ("net: ipa: introduce ipa_cmd_tag_process()")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8afc7e471a ]
The IPA setup_complete flag is set at the end of ipa_setup(), when
the setup phase of initialization has completed successfully. This
occurs as part of driver probe processing, or (if "modem-init" is
specified in the DTS file) it is triggered by the "ipa-setup-ready"
SMP2P interrupt generated by the modem.
In the latter case, it's possible for driver shutdown (or remove) to
begin while setup processing is underway, and this can't be allowed.
The problem is that the setup_complete flag is not adequate to signal
that setup is underway.
If setup_complete is set, it will never be un-set, so that case is
not a problem. But if setup_complete is false, there's a chance
setup is underway.
Because setup is triggered by an interrupt on a "modem-init" system,
there is a simple way to ensure the value of setup_complete is safe
to read. The threaded handler--if it is executing--will complete as
part of a request to disable the "ipa-modem-ready" interrupt. This
means that ipa_setup() (which is called from the handler) will run
to completion if it was underway, or will never be called otherwise.
The request to disable the "ipa-setup-ready" interrupt is currently
made within ipa_modem_stop(). Instead, disable the interrupt
outside that function in the two places it's called. In the case of
ipa_remove(), this ensures the setup_complete flag is safe to read
before we read it.
Rename ipa_smp2p_disable() to be ipa_smp2p_irq_disable_setup(), to be
more specific about its effect.
Fixes: 530f9216a9 ("soc: qcom: ipa: AP/modem communications")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33a153100b ]
We currently maintain a "disabled" Boolean flag to determine whether
the "ipa-setup-ready" SMP2P IRQ handler does anything. That flag
must be accessed under protection of a mutex.
Instead, disable the SMP2P interrupt when requested, which prevents
the interrupt handler from ever being called. More importantly, it
synchronizes a thread disabling the interrupt with the completion of
the interrupt handler in case they run concurrently.
Use the IPA setup_complete flag rather than the disabled flag in the
handler to determine whether to ignore any interrupts arriving after
the first.
Rename the "disabled" flag to be "setup_disabled", to be specific
about its purpose.
Fixes: 530f9216a9 ("soc: qcom: ipa: AP/modem communications")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63b08b1f68 ]
When processing port up/down events generated by the device's firmware,
the driver protects itself from events reported for non-existent local
ports, but not the CPU port (local port 0), which exists, but lacks a
netdev.
This can result in a NULL pointer dereference when calling
netif_carrier_{on,off}().
Fix this by bailing early when processing an event reported for the CPU
port. Problem was only observed when running on top of a buggy emulator.
Fixes: 28b1987ef5 ("mlxsw: spectrum: Register CPU port with devlink")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 606a63c978 ]
The side that actively closed socket, it's clcsock doesn't enter
TIME_WAIT state, but the passive side does it. It should show the same
behavior as TCP sockets.
Consider this, when client actively closes the socket, the clcsock in
server enters TIME_WAIT state, which means the address is occupied and
won't be reused before TIME_WAIT dismissing. If we restarted server, the
service would be unavailable for a long time.
To solve this issue, shutdown the clcsock in [A], perform the TCP active
close progress first, before the passive closed side closing it. So that
the actively closed side enters TIME_WAIT, not the passive one.
Client | Server
close() // client actively close |
smc_release() |
smc_close_active() // PEERCLOSEWAIT1 |
smc_close_final() // abort or closed = 1|
smc_cdc_get_slot_and_msg_send() |
[A] |
|smc_cdc_msg_recv_action() // ACTIVE
| queue_work(smc_close_wq, &conn->close_work)
| smc_close_passive_work() // PROCESSABORT or APPCLOSEWAIT1
| smc_close_passive_abort_received() // only in abort
|
|close() // server recv zero, close
| smc_release() // PROCESSABORT or APPCLOSEWAIT1
| smc_close_active()
| smc_close_abort() or smc_close_final() // CLOSED
| smc_cdc_get_slot_and_msg_send() // abort or closed = 1
smc_cdc_msg_recv_action() | smc_clcsock_release()
queue_work(smc_close_wq, &conn->close_work) | sock_release(tcp) // actively close clc, enter TIME_WAIT
smc_close_passive_work() // PEERCLOSEWAIT1 | smc_conn_free()
smc_close_passive_abort_received() // CLOSED|
smc_conn_free() |
smc_clcsock_release() |
sock_release(tcp) // passive close clc |
Link: https://www.spinics.net/lists/netdev/msg780407.html
Fixes: b38d732477 ("smc: socket closing and linkgroup cleanup")
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84e1d0bf1d ]
If a timeout is hit, it can result is incorrect data on the I2C bus
and/or memory corruptions in the guest since the device can still be
operating on the buffers it was given while the guest has freed them.
Here is, for example, the start of a slub_debug splat which was
triggered on the next transfer after one transfer was forced to timeout
by setting a breakpoint in the backend (rust-vmm/vhost-device):
BUG kmalloc-1k (Not tainted): Poison overwritten
First byte 0x1 instead of 0x6b
Allocated in virtio_i2c_xfer+0x65/0x35c age=350 cpu=0 pid=29
__kmalloc+0xc2/0x1c9
virtio_i2c_xfer+0x65/0x35c
__i2c_transfer+0x429/0x57d
i2c_transfer+0x115/0x134
i2cdev_ioctl_rdwr+0x16a/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
Freed in virtio_i2c_xfer+0x32e/0x35c age=244 cpu=0 pid=29
kfree+0x1bd/0x1cc
virtio_i2c_xfer+0x32e/0x35c
__i2c_transfer+0x429/0x57d
i2c_transfer+0x115/0x134
i2cdev_ioctl_rdwr+0x16a/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
There is no simple fix for this (the driver would have to always create
bounce buffers and hold on to them until the device eventually returns
the buffers), so just disable the timeout support for now.
Fixes: 3cfc883804 ("i2c: virtio: add a virtio i2c frontend driver")
Acked-by: Jie Deng <jie.deng@intel.com>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57bbeacdbe ]
We observed the following deadlock in the stress test under low
memory scenario:
Thread A Thread B
- erofs_shrink_scan
- erofs_try_to_release_workgroup
- erofs_workgroup_try_to_freeze -- A
- z_erofs_do_read_page
- z_erofs_collection_begin
- z_erofs_register_collection
- erofs_insert_workgroup
- xa_lock(&sbi->managed_pslots) -- B
- erofs_workgroup_get
- erofs_wait_on_workgroup_freezed -- A
- xa_erase
- xa_lock(&sbi->managed_pslots) -- B
To fix this, it needs to hold xa_lock before freezing the workgroup
since xarray will be touched then. So let's hold the lock before
accessing each workgroup, just like what we did with the radix tree
before.
[ Gao Xiang: Jianhua Hao also reports this issue at
https://lore.kernel.org/r/b10b85df30694bac8aadfe43537c897a@xiaomi.com ]
Link: https://lore.kernel.org/r/20211118135844.3559-1-huangjianan@oppo.com
Fixes: 64094a0441 ("erofs: convert workstn to XArray")
Reviewed-by: Chao Yu <chao@kernel.org>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Huang Jianan <huangjianan@oppo.com>
Reported-by: Jianhua Hao <haojianhua1@xiaomi.com>
Signed-off-by: Gao Xiang <xiang@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1005f19b93 ]
When replacing a nexthop group, we must release the IPv6 per-cpu dsts of
the removed nexthop entries after an RCU grace period because they
contain references to the nexthop's net device and to the fib6 info.
With specific series of events[1] we can reach net device refcount
imbalance which is unrecoverable. IPv4 is not affected because dsts
don't take a refcount on the route.
[1]
$ ip nexthop list
id 200 via 2002:db8::2 dev bridge.10 scope link onlink
id 201 via 2002:db8::3 dev bridge scope link onlink
id 203 group 201/200
$ ip -6 route
2001:db8::10 nhid 203 metric 1024 pref medium
nexthop via 2002:db8::3 dev bridge weight 1 onlink
nexthop via 2002:db8::2 dev bridge.10 weight 1 onlink
Create rt6_info through one of the multipath legs, e.g.:
$ taskset -a -c 1 ./pkt_inj 24 bridge.10 2001:db8::10
(pkt_inj is just a custom packet generator, nothing special)
Then remove that leg from the group by replace (let's assume it is id
200 in this case):
$ ip nexthop replace id 203 group 201
Now remove the IPv6 route:
$ ip -6 route del 2001:db8::10/128
The route won't be really deleted due to the stale rt6_info holding 1
refcnt in nexthop id 200.
At this point we have the following reference count dependency:
(deleted) IPv6 route holds 1 reference over nhid 203
nh 203 holds 1 ref over id 201
nh 200 holds 1 ref over the net device and the route due to the stale
rt6_info
Now to create circular dependency between nh 200 and the IPv6 route, and
also to get a reference over nh 200, restore nhid 200 in the group:
$ ip nexthop replace id 203 group 201/200
And now we have a permanent circular dependncy because nhid 203 holds a
reference over nh 200 and 201, but the route holds a ref over nh 203 and
is deleted.
To trigger the bug just delete the group (nhid 203):
$ ip nexthop del id 203
It won't really be deleted due to the IPv6 route dependency, and now we
have 2 unlinked and deleted objects that reference each other: the group
and the IPv6 route. Since the group drops the reference it holds over its
entries at free time (i.e. its own refcount needs to drop to 0) that will
never happen and we get a permanent ref on them, since one of the entries
holds a reference over the IPv6 route it will also never be released.
At this point the dependencies are:
(deleted, only unlinked) IPv6 route holds reference over group nh 203
(deleted, only unlinked) group nh 203 holds reference over nh 201 and 200
nh 200 holds 1 ref over the net device and the route due to the stale
rt6_info
This is the last point where it can be fixed by running traffic through
nh 200, and specifically through the same CPU so the rt6_info (dst) will
get released due to the IPv6 genid, that in turn will free the IPv6
route, which in turn will free the ref count over the group nh 203.
If nh 200 is deleted at this point, it will never be released due to the
ref from the unlinked group 203, it will only be unlinked:
$ ip nexthop del id 200
$ ip nexthop
$
Now we can never release that stale rt6_info, we have IPv6 route with ref
over group nh 203, group nh 203 with ref over nh 200 and 201, nh 200 with
rt6_info (dst) with ref over the net device and the IPv6 route. All of
these objects are only unlinked, and cannot be released, thus they can't
release their ref counts.
Message from syslogd@dev at Nov 19 14:04:10 ...
kernel:[73501.828730] unregister_netdevice: waiting for bridge.10 to become free. Usage count = 3
Message from syslogd@dev at Nov 19 14:04:20 ...
kernel:[73512.068811] unregister_netdevice: waiting for bridge.10 to become free. Usage count = 3
Fixes: 7bf4796dd0 ("nexthops: add support for replace")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8837cbbf85 ]
We need a way to release a fib6_nh's per-cpu dsts when replacing
nexthops otherwise we can end up with stale per-cpu dsts which hold net
device references, so add a new IPv6 stub called fib6_nh_release_dsts.
It must be used after an RCU grace period, so no new dsts can be created
through a group's nexthop entry.
Similar to fib6_nh_release it shouldn't be used if fib6_nh_init has failed
so it doesn't need a dummy stub when IPv6 is not enabled.
Fixes: 7bf4796dd0 ("nexthops: add support for replace")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6da2bbb00 ]
Currently, when user space emits SIOCSHWTSTAMP ioctl calls such as
enabling/disabling timestamping or changing filter settings, the driver
reads the current CLOCK_REALTIME value and programming this into the
NIC's hardware clock. This might be necessary during system
initialization, but at runtime, when the PTP clock has already been
synchronized to a grandmaster, a reset of the timestamp settings might
result in a clock jump. Furthermore, if the clock is also controlled by
phc2sys in automatic mode (where the UTC offset is queried from ptp4l),
that UTC-to-TAI offset (currently 37 seconds in 2021) would be
temporarily reset to 0, and it would take a long time for phc2sys to
readjust so that CLOCK_REALTIME and the PHC are apart by 37 seconds
again.
To address the issue, we introduce a new function called
stmmac_init_tstamp_counter(), which gets called during ndo_open().
It contains the code snippet moved from stmmac_hwtstamp_set() that
manages the time synchronization. Besides, the sub second increment
configuration is also moved here since the related values are hardware
dependent and runtime invariant.
Furthermore, the hardware clock must be kept running even when no time
stamping mode is selected in order to retain the synchronized time base.
That way, timestamping can be enabled again at any time only with the
need to compensate the clock's natural drifting.
As a side effect, this patch fixes the issue that ptp_clock_info::enable
can be called before SIOCSHWTSTAMP and the driver (which looks at
priv->systime_flags) was not prepared to handle that ordering.
Fixes: 92ba688851 ("stmmac: add the support for PTP hw clock driver")
Reported-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bd6b2a838 ]
Use nn->tlv_caps.me_freq_mhz instead of nn->me_freq_mhz to check whether
rx-usecs/tx-usecs is valid.
This is because nn->tlv_caps.me_freq_mhz represents the clock_freq (MHz) of
the flow processing cores (FPC) on the NIC. While nn->me_freq_mhz is not
be set.
Fixes: ce991ab666 ("nfp: read ME frequency from vNIC ctrl memory")
Signed-off-by: Diana Wang <na.wang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e95d8eaee2 ]
The ARCH_FEATURES function ID is a 32-bit SMC call, which returns
a 32-bit result per the SMCCC spec. Current code is doing a 64-bit
comparison against -1 (SMCCC_RET_NOT_SUPPORTED) to detect that the
feature is unimplemented. That check doesn't work in a Hyper-V VM,
where the upper 32-bits are zero as allowed by the spec.
Cast the result as an 'int' so the comparison works. The change also
makes the code consistent with other similar checks in this file.
Fixes: 821b67fa46 ("firmware: smccc: Add ARCH_SOC_ID support")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9390b249c ]
On kernels before v5.15, calling read() on a unix socket after
shutdown(SHUT_RD) or shutdown(SHUT_RDWR) would return the data
previously written or EOF. But now, while read() after
shutdown(SHUT_RD) still behaves the same way, read() after
shutdown(SHUT_RDWR) always fails with -EINVAL.
This behaviour change was apparently inadvertently introduced as part of
a bug fix for a different regression caused by the commit adding sockmap
support to af_unix, commit 94531cfcbe ("af_unix: Add
unix_stream_proto for sockmap"). Those commits, for unclear reasons,
started setting the socket state to TCP_CLOSE on shutdown(SHUT_RDWR),
while this state change had previously only been done in
unix_release_sock().
Restore the original behaviour. The sockmap tests in
tests/selftests/bpf continue to pass after this patch.
Fixes: d0c6416bd7 ("unix: Fix an issue in unix_shutdown causing the other end read/write failures")
Link: https://lore.kernel.org/lkml/20211111140000.GA10779@axis.com/
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Tested-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcd9773431 ]
Scheduling a delack in mptcp_established_options_mp() is
not a good idea: such function is called by tcp_send_ack() and
the pending delayed ack will be cleared shortly after by the
tcp_event_ack_sent() call in __tcp_transmit_skb().
Instead use the mptcp delegated action infrastructure to
schedule the delayed ack after the current bh processing completes.
Additionally moves the schedule_3rdack_retransmission() helper
into protocol.c to avoid making it visible in a different compilation
unit.
Fixes: ec3edaa7ca ("mptcp: Add handling of outgoing MP_JOIN requests")
Reviewed-by: Mat Martineau <mathew.j.martineau>@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee50e67ba0 ]
To compute the rtx timeout schedule_3rdack_retransmission() does multiple
things in the wrong way: srtt_us is measured in usec/8 and the timeout
itself is an absolute value.
Fixes: ec3edaa7ca ("mptcp: Add handling of outgoing MP_JOIN requests")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau>@linux.intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5951a2b981 ]
When a VF goes through a reset, it's possible for the VF's feature set
to change. For example it may lose the VIRTCHNL_VF_OFFLOAD_VLAN
capability after VF reset. Unfortunately, the driver doesn't correctly
deal with this situation and errors are seen from downing/upping the
interface and/or moving the interface in/out of a network namespace.
When setting the interface down/up we see the following errors after the
VIRTCHNL_VF_OFFLOAD_VLAN capability was taken away from the VF:
ice 0000:51:00.1: VF 1 failed opcode 12, retval: -64 iavf 0000:51:09.1:
Failed to add VLAN filter, error IAVF_NOT_SUPPORTED ice 0000:51:00.1: VF
1 failed opcode 13, retval: -64 iavf 0000:51:09.1: Failed to delete VLAN
filter, error IAVF_NOT_SUPPORTED
These add/delete errors are happening because the VLAN filters are
tracked internally to the driver and regardless of the VLAN_ALLOWED()
setting the driver tries to delete/re-add them over virtchnl.
Fix the delete failure by making sure to delete any VLAN filter tracking
in the driver when a removal request is made, while preventing the
virtchnl request. This makes it so the driver's VLAN list is up to date
and the errors are
Fix the add failure by making sure the check for VLAN_ALLOWED() during
reset is done after the VF receives its capability list from the PF via
VIRTCHNL_OP_GET_VF_RESOURCES. If VLAN functionality is not allowed, then
prevent requesting re-adding the filters over virtchnl.
When moving the interface into a network namespace we see the following
errors after the VIRTCHNL_VF_OFFLOAD_VLAN capability was taken away from
the VF:
iavf 0000:51:09.1 enp81s0f1v1: NIC Link is Up Speed is 25 Gbps Full Duplex
iavf 0000:51:09.1 temp_27: renamed from enp81s0f1v1
iavf 0000:51:09.1 mgmt: renamed from temp_27
iavf 0000:51:09.1 dev27: set_features() failed (-22); wanted 0x020190001fd54833, left 0x020190001fd54bb3
These errors are happening because we aren't correctly updating the
netdev capabilities and dealing with ndo_fix_features() and
ndo_set_features() correctly.
Fix this by only reporting errors in the driver's ndo_set_features()
callback when VIRTCHNL_VF_OFFLOAD_VLAN is not allowed and any attempt to
enable the VLAN features is made. Also, make sure to disable VLAN
insertion, filtering, and stripping since the VIRTCHNL_VF_OFFLOAD_VLAN
flag applies to all of them and not just VLAN stripping.
Also, after we process the capabilities in the VF reset path, make sure
to call netdev_update_features() in case the capabilities have changed
in order to update the netdev's feature set to match the VF's actual
capabilities.
Lastly, make sure to always report success on VLAN filter delete when
VIRTCHNL_VF_OFFLOAD_VLAN is not supported. The changed flow in
iavf_del_vlans() allows the stack to delete previosly existing VLAN
filters even if VLAN filtering is not allowed. This makes it so the VLAN
filter list is up to date.
Fixes: 8774370d26 ("i40e/i40evf: support for VF VLAN tag stripping control")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b5bdd18eb ]
Currently iavf adapter statistics are refreshed only in a
watchdog task, triggered approximately every two seconds,
which causes some ethtool requests to return outdated values.
Add explicit statistics refresh when requested by ethtool -S.
Fixes: b476b0030e ("iavf: Move commands processing to the separate function")
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e792779e6b ]
Resolve being able to change static values on VF when adaptive interrupt
moderation is enabled.
This problem is fixed by checking the interrupt settings is not
a combination of change of static value while adaptive interrupt
moderation is turned on.
Without this fix, the user would be able to change static values
on VF with adaptive moderation enabled.
Fixes: 65e87c0398 ("i40evf: support queue-specific settings for interrupt moderation")
Signed-off-by: Nitesh B Venkatesh <nitesh.b.venkatesh@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1091118e0 ]
In hid_magicmouse, if the user has set scroll_speed to a value between
55 and 63 and scrolls seven times in quick succession, the
step_hr variable in the magicmouse_emit_touch function becomes 0.
That causes a division by zero further down in the function when
it does `step_x_hr /= step_hr`.
To reproduce, create `/etc/modprobe.d/hid_magicmouse.conf` with the
following content:
```
options hid_magicmouse scroll_acceleration=1 scroll_speed=55
```
Then reboot, connect a Magic Mouse and scroll seven times quickly.
The system will freeze for a minute, and after that `dmesg` will
confirm that a division by zero occurred.
Enforce a minimum of 1 for the variable so the high resolution
step count can never reach 0 even at maximum scroll acceleration.
Fixes: d4b9f10a0e ("HID: magicmouse: enable high-resolution scroll")
Signed-off-by: Claudia Pellegrino <linux@cpellegrino.de>
Tested-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e6a950d98 ]
When a scancode is manually remapped that previously was not handled as
key, then the old usage type was incorrectly reused.
This caused issues on a "04b3:301b IBM Corp. SK-8815 Keyboard" which has
marked some of its keys with an invalid HID usage. These invalid usage
keys are being ignored since support for USB programmable buttons was
added.
The scancodes are however remapped explicitly by the systemd hwdb to the
keycodes that are printed on the physical buttons. During this mapping
step the existing usage is retrieved which will be found with a default
type of 0 (EV_SYN) instead of EV_KEY.
The events with the correct code but EV_SYN type are not forwarded to
userspace.
This also leads to a kernel oops when trying to print the report descriptor
via debugfs. hid_resolv_event() tries to resolve a EV_SYN event with an
EV_KEY code which leads to an out-of-bounds access in the EV_SYN names
array.
Fixes: bcfa8d1457 ("HID: input: Add support for Programmable Buttons")
Fixes: f5854fad39 ("Input: hid-input - allow mapping unknown usages")
Reported-by: Brent Roman <brent@mbari.org>
Tested-by: Brent Roman <brent@mbari.org>
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 253e9b4d11 ]
Return NOTIFY_DONE (dont't care) for switchdev notifications
that prestera driver don't know how to handle them.
With introduction of SWITCHDEV_BRPORT_[UN]OFFLOADED switchdev
events, the driver rejects adding swport to bridge operation
which is handled by prestera_bridge_port_join() func. The root
cause of this is that prestera driver returns error (EOPNOTSUPP)
in prestera_switchdev_blk_event() handler for unknown swdev
events. This causes switchdev_bridge_port_offload() to fail
when adding port to bridge in prestera_bridge_port_join().
Fixes: 957e2235e5 ("net: make switchdev_bridge_port_{,unoffload} loosely coupled with the bridge")
Signed-off-by: Volodymyr Mytnyk <vmytnyk@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4a6aaeaf4 ]
Before the drm driver had support for this file there was a driver that
exposed the contents of the vga password register to userspace. It would
present the entire register instead of interpreting it.
The drm implementation chose to mask of the lower bit, without explaining
why. This breaks the existing userspace, which is looking for 0xa8 in
the lower byte.
Change our implementation to expose the entire register.
Fixes: 696029eb36 ("drm/aspeed: Add sysfs for output settings")
Reported-by: Oskar Senft <osk@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Tested-by: Oskar Senft <osk@google.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211117010145.297253-1-joel@jms.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ecae9f8c7 ]
For updating the IOC firmware's timestamp with system timestamp, the driver
issues the Mpi26IoUnitControlRequest message. While framing the
Mpi26IoUnitControlRequest, the driver should copy the lower 32 bits of the
current timestamp into IOCParameterValue field and the higher 32 bits into
Reserved7 field.
Link: https://lore.kernel.org/r/20211117123215.25487-1-sreekanth.reddy@broadcom.com
Fixes: f98790c003 ("scsi: mpt3sas: Sync time periodically between driver and firmware")
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91202a01a2 ]
While determining the SAS address of a drive, the driver checks whether the
handle number is less than the HBA phy count or not. If the handle number
is less than the HBA phy count then driver assumes that this handle belongs
to HBA and hence it assigns the HBA SAS address.
During IOC firmware downgrade operation, if the number of HBA phys is
reduced and the OS drive's device handle drops below the phy count while
determining the drive's SAS address, the driver ends up using the HBA's SAS
address. This leads to a mismatch of drive's SAS address and hence the
driver unregisters the OS drive and the system goes into read-only mode.
Update the IOC's num_phys to the HBA phy count provided by actual loaded
firmware.
Link: https://lore.kernel.org/r/20211117105058.3505-1-sreekanth.reddy@broadcom.com
Fixes: a5e99fda01 ("scsi: mpt3sas: Update hba_port objects after host reset")
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ee4ba13e0 ]
While looping over shost's sdev list it is possible that one
of the drives is getting removed and its sas_target object is
freed but its sdev object remains intact.
Consequently, a kernel panic can occur while the driver is trying to access
the sas_address field of sas_target object without also checking the
sas_target object for NULL.
Link: https://lore.kernel.org/r/20211117104909.2069-1-sreekanth.reddy@broadcom.com
Fixes: f92363d123 ("[SCSI] mpt3sas: add new driver supporting 12GB SAS")
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3c45824ad ]
The failure to retrieve post-op attributes has no bearing on whether or
not the clone operation itself was successful. We must therefore ignore
the return value of decode_getfattr() when looking at the success or
failure of nfs4_xdr_dec_clone().
Fixes: 36022770de ("nfs42: add CLONE xdr functions")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
