commit 8ff80e96e3 upstream.
Test different scenarios of indirect variable-offset stack access: out of
bound access (>0), min_off below initialized part of the stack,
max_off+size above initialized part of the stack, initialized stack.
Example of output:
...
#856/p indirect variable-offset stack access, out of bound OK
#857/p indirect variable-offset stack access, max_off+size > max_initialized OK
#858/p indirect variable-offset stack access, min_off < min_initialized OK
#859/p indirect variable-offset stack access, ok OK
...
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
[OP: backport to 4.19]
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 107c26a70c upstream.
As discussed in [1] max value of variable offset has to be checked for
overflow on stack access otherwise verifier would accept code like this:
0: (b7) r2 = 6
1: (b7) r3 = 28
2: (7a) *(u64 *)(r10 -16) = 0
3: (7a) *(u64 *)(r10 -8) = 0
4: (79) r4 = *(u64 *)(r1 +168)
5: (c5) if r4 s< 0x0 goto pc+4
R1=ctx(id=0,off=0,imm=0) R2=inv6 R3=inv28
R4=inv(id=0,umax_value=9223372036854775807,var_off=(0x0;
0x7fffffffffffffff)) R10=fp0,call_-1 fp-8=mmmmmmmm fp-16=mmmmmmmm
6: (17) r4 -= 16
7: (0f) r4 += r10
8: (b7) r5 = 8
9: (85) call bpf_getsockopt#57
10: (b7) r0 = 0
11: (95) exit
, where R4 obviosly has unbounded max value.
Fix it by checking that reg->smax_value is inside (-BPF_MAX_VAR_OFF;
BPF_MAX_VAR_OFF) range.
reg->smax_value is used instead of reg->umax_value because stack
pointers are calculated using negative offset from fp. This is opposite
to e.g. map access where offset must be non-negative and where
umax_value is used.
Also dedicated verbose logs are added for both min and max bound check
failures to have diagnostics consistent with variable offset handling in
check_map_access().
[1] https://marc.info/?l=linux-netdev&m=155433357510597&w=2
Fixes: 2011fccfb6 ("bpf: Support variable offset stack access from helpers")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 088ec26d9c upstream.
Proper support of indirect stack access with variable offset in
unprivileged mode (!root) requires corresponding support in Spectre
masking for stack ALU in retrieve_ptr_limit().
There are no use-case for variable offset in unprivileged mode though so
make verifier reject such accesses for simplicity.
Pointer arithmetics is one (and only?) way to cause variable offset and
it's already rejected in unpriv mode so that verifier won't even get to
helper function whose argument contains variable offset, e.g.:
0: (7a) *(u64 *)(r10 -16) = 0
1: (7a) *(u64 *)(r10 -8) = 0
2: (61) r2 = *(u32 *)(r1 +0)
3: (57) r2 &= 4
4: (17) r2 -= 16
5: (0f) r2 += r10
variable stack access var_off=(0xfffffffffffffff0; 0x4) off=-16 size=1R2
stack pointer arithmetic goes out of range, prohibited for !root
Still it looks like a good idea to reject variable offset indirect stack
access for unprivileged mode in check_stack_boundary() explicitly.
Fixes: 2011fccfb6 ("bpf: Support variable offset stack access from helpers")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
[OP: drop comment in retrieve_ptr_limit()]
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2bcd05ec7 upstream.
It's hard to guarantee that whole memory is marked as initialized on
helper return if uninitialized stack is accessed with variable offset
since specific bounds are unknown to verifier. This may cause
uninitialized stack leaking.
Reject such an access in check_stack_boundary to prevent possible
leaking.
There are no known use-cases for indirect uninitialized stack access
with variable offset so it shouldn't break anything.
Fixes: 2011fccfb6 ("bpf: Support variable offset stack access from helpers")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2011fccfb6 upstream.
Currently there is a difference in how verifier checks memory access for
helper arguments for PTR_TO_MAP_VALUE and PTR_TO_STACK with regard to
variable part of offset.
check_map_access, that is used for PTR_TO_MAP_VALUE, can handle variable
offsets just fine, so that BPF program can call a helper like this:
some_helper(map_value_ptr + off, size);
, where offset is unknown at load time, but is checked by program to be
in a safe rage (off >= 0 && off + size < map_value_size).
But it's not the case for check_stack_boundary, that is used for
PTR_TO_STACK, and same code with pointer to stack is rejected by
verifier:
some_helper(stack_value_ptr + off, size);
For example:
0: (7a) *(u64 *)(r10 -16) = 0
1: (7a) *(u64 *)(r10 -8) = 0
2: (61) r2 = *(u32 *)(r1 +0)
3: (57) r2 &= 4
4: (17) r2 -= 16
5: (0f) r2 += r10
6: (18) r1 = 0xffff888111343a80
8: (85) call bpf_map_lookup_elem#1
invalid variable stack read R2 var_off=(0xfffffffffffffff0; 0x4)
Add support for variable offset access to check_stack_boundary so that
if offset is checked by program to be in a safe range it's accepted by
verifier.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
[OP: replace reg_state(env, regno) helper with "cur_regs(env) + regno"]
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bae2d4d62 upstream.
Verifier is supposed to support sharing stack slot allocated to ptr with
SCALAR_VALUE for privileged program. However this doesn't happen for some
cases.
The reason is verifier is not clearing slot_type STACK_SPILL for all bytes,
it only clears part of them, while verifier is using:
slot_type[0] == STACK_SPILL
as a convention to check one slot is ptr type.
So, the consequence of partial clearing slot_type is verifier could treat a
partially overridden ptr slot, which should now be a SCALAR_VALUE slot,
still as ptr slot, and rejects some valid programs.
Before this patch, test_xdp_noinline.o under bpf selftests, bpf_lxc.o and
bpf_netdev.o under Cilium bpf repo, when built with -mattr=+alu32 are
rejected due to this issue. After this patch, they all accepted.
There is no processed insn number change before and after this patch on
Cilium bpf programs.
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
[OP: adjusted context for 4.19]
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 679c782de1 upstream.
By giving each register its own liveness chain, we elide the skip_callee()
logic. Instead, each register's parent is the state it inherits from;
both check_func_call() and prepare_func_exit() automatically connect
reg states to the correct chain since when they copy the reg state across
(r1-r5 into the callee as args, and r0 out as the return value) they also
copy the parent pointer.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
[OP: adjusted context for 4.19]
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b511d5bfa upstream.
Xen PV guests are specifying the highest used PFN via the max_pfn
field in shared_info. This value is used by the Xen tools when saving
or migrating the guest.
Unfortunately this field is misnamed, as in reality it is specifying
the number of pages (including any memory holes) of the guest, so it
is the highest used PFN + 1. Renaming isn't possible, as this is a
public Xen hypervisor interface which needs to be kept stable.
The kernel will set the value correctly initially at boot time, but
when adding more pages (e.g. due to memory hotplug or ballooning) a
real PFN number is stored in max_pfn. This is done when expanding the
p2m array, and the PFN stored there is even possibly wrong, as it
should be the last possible PFN of the just added P2M frame, and not
one which led to the P2M expansion.
Fix that by setting shared_info->max_pfn to the last possible PFN + 1.
Fixes: 98dd166ea3 ("x86/xen/p2m: hint at the last populated P2M entry")
Cc: stable@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Link: https://lore.kernel.org/r/20210730092622.9973-2-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9addd85fb upstream.
H_GetPerformanceCounterInfo (0xF080) hcall returns the counter data in
the result buffer. Result buffer has specific format defined in the PAPR
specification. One of the fields is counter offset and width of the
counter data returned.
Counter data are returned in a unsigned char array in big endian byte
order. To get the final counter data, the values must be left shifted
byte at a time. But commit 220a0c609a ("powerpc/perf: Add support for
the hv gpci (get performance counter info) interface") made the shifting
bitwise and also assumed little endian order. Because of that, hcall
counters values are reported incorrectly.
In particular this can lead to counters go backwards which messes up the
counter prev vs now calculation and leads to huge counter value
reporting:
#: perf stat -e hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
-C 0 -I 1000
time counts unit events
1.000078854 18,446,744,073,709,535,232 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
2.000213293 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
3.000320107 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
4.000428392 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
5.000537864 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
6.000649087 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
7.000760312 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
8.000865218 16,448 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
9.000978985 18,446,744,073,709,535,232 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
10.001088891 16,384 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
11.001201435 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
12.001307937 18,446,744,073,709,535,232 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
Fix the shifting logic to correct match the format, ie. read bytes in
big endian order.
Fixes: e4f226b158 ("powerpc/perf/hv-gpci: Increase request buffer size")
Cc: stable@vger.kernel.org # v4.6+
Reported-by: Nageswara R Sastry<rnsastry@linux.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Tested-by: Nageswara R Sastry<rnsastry@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210813082158.429023-1-kjain@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a519dc7a7 upstream.
When running as Xen PV guest, masking MSI-X is a responsibility of the
hypervisor. The guest has no write access to the relevant BAR at all - when
it tries to, it results in a crash like this:
BUG: unable to handle page fault for address: ffffc9004069100c
#PF: supervisor write access in kernel mode
#PF: error_code(0x0003) - permissions violation
RIP: e030:__pci_enable_msix_range.part.0+0x26b/0x5f0
e1000e_set_interrupt_capability+0xbf/0xd0 [e1000e]
e1000_probe+0x41f/0xdb0 [e1000e]
local_pci_probe+0x42/0x80
(...)
The recently introduced function msix_mask_all() does not check the global
variable pci_msi_ignore_mask which is set by XEN PV to bypass the masking
of MSI[-X] interrupts.
Add the check to make this function XEN PV compatible.
Fixes: 7d5ec3d361 ("PCI/MSI: Mask all unused MSI-X entries")
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210826170342.135172-1-marmarek@invisiblethingslab.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ead3b768bb upstream.
Zone management send operations (BLKRESETZONE, BLKOPENZONE, BLKCLOSEZONE
and BLKFINISHZONE) should be allowed under the same permissions as write().
(write() does not require CAP_SYS_ADMIN).
Additionally, other ioctls like BLKSECDISCARD and BLKZEROOUT only check if
the fd was successfully opened with FMODE_WRITE.
(They do not require CAP_SYS_ADMIN).
Currently, zone management send operations require both CAP_SYS_ADMIN
and that the fd was successfully opened with FMODE_WRITE.
Remove the CAP_SYS_ADMIN requirement, so that zone management send
operations match the access control requirement of write(), BLKSECDISCARD
and BLKZEROOUT.
Fixes: 3ed05a987e ("blk-zoned: implement ioctls")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Aravind Ramesh <aravind.ramesh@wdc.com>
Reviewed-by: Adam Manzanares <a.manzanares@samsung.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: stable@vger.kernel.org # v4.10+
Link: https://lore.kernel.org/r/20210811110505.29649-2-Niklas.Cassel@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d977e0eba upstream.
This crash was observed with a failed assertion on device close:
BTRFS: Transaction aborted (error -28)
WARNING: CPU: 1 PID: 3902 at fs/btrfs/extent-tree.c:2150 btrfs_run_delayed_refs+0x1d2/0x1e0 [btrfs]
Modules linked in: btrfs blake2b_generic libcrc32c crc32c_intel xor zstd_decompress zstd_compress xxhash lzo_compress lzo_decompress raid6_pq loop
CPU: 1 PID: 3902 Comm: kworker/u8:4 Not tainted 5.14.0-rc5-default+ #1532
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba527-rebuilt.opensuse.org 04/01/2014
Workqueue: events_unbound btrfs_async_reclaim_metadata_space [btrfs]
RIP: 0010:btrfs_run_delayed_refs+0x1d2/0x1e0 [btrfs]
RSP: 0018:ffffb7a5452d7d80 EFLAGS: 00010282
RAX: 0000000000000000 RBX: 0000000000000003 RCX: 0000000000000000
RDX: 0000000000000001 RSI: ffffffffabee13c4 RDI: 00000000ffffffff
RBP: ffff97834176a378 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000001 R12: ffff97835195d388
R13: 0000000005b08000 R14: ffff978385484000 R15: 000000000000016c
FS: 0000000000000000(0000) GS:ffff9783bd800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000056190d003fe8 CR3: 000000002a81e005 CR4: 0000000000170ea0
Call Trace:
flush_space+0x197/0x2f0 [btrfs]
btrfs_async_reclaim_metadata_space+0x139/0x300 [btrfs]
process_one_work+0x262/0x5e0
worker_thread+0x4c/0x320
? process_one_work+0x5e0/0x5e0
kthread+0x144/0x170
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
irq event stamp: 19334989
hardirqs last enabled at (19334997): [<ffffffffab0e0c87>] console_unlock+0x2b7/0x400
hardirqs last disabled at (19335006): [<ffffffffab0e0d0d>] console_unlock+0x33d/0x400
softirqs last enabled at (19334900): [<ffffffffaba0030d>] __do_softirq+0x30d/0x574
softirqs last disabled at (19334893): [<ffffffffab0721ec>] irq_exit_rcu+0x12c/0x140
---[ end trace 45939e308e0dd3c7 ]---
BTRFS: error (device vdd) in btrfs_run_delayed_refs:2150: errno=-28 No space left
BTRFS info (device vdd): forced readonly
BTRFS warning (device vdd): failed setting block group ro: -30
BTRFS info (device vdd): suspending dev_replace for unmount
assertion failed: !test_bit(BTRFS_DEV_STATE_REPLACE_TGT, &device->dev_state), in fs/btrfs/volumes.c:1150
------------[ cut here ]------------
kernel BUG at fs/btrfs/ctree.h:3431!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 1 PID: 3982 Comm: umount Tainted: G W 5.14.0-rc5-default+ #1532
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba527-rebuilt.opensuse.org 04/01/2014
RIP: 0010:assertfail.constprop.0+0x18/0x1a [btrfs]
RSP: 0018:ffffb7a5454c7db8 EFLAGS: 00010246
RAX: 0000000000000068 RBX: ffff978364b91c00 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffffabee13c4 RDI: 00000000ffffffff
RBP: ffff9783523a4c00 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000001 R12: ffff9783523a4d18
R13: 0000000000000000 R14: 0000000000000004 R15: 0000000000000003
FS: 00007f61c8f42800(0000) GS:ffff9783bd800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000056190cffa810 CR3: 0000000030b96002 CR4: 0000000000170ea0
Call Trace:
btrfs_close_one_device.cold+0x11/0x55 [btrfs]
close_fs_devices+0x44/0xb0 [btrfs]
btrfs_close_devices+0x48/0x160 [btrfs]
generic_shutdown_super+0x69/0x100
kill_anon_super+0x14/0x30
btrfs_kill_super+0x12/0x20 [btrfs]
deactivate_locked_super+0x2c/0xa0
cleanup_mnt+0x144/0x1b0
task_work_run+0x59/0xa0
exit_to_user_mode_loop+0xe7/0xf0
exit_to_user_mode_prepare+0xaf/0xf0
syscall_exit_to_user_mode+0x19/0x50
do_syscall_64+0x4a/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
This happens when close_ctree is called while a dev_replace hasn't
completed. In close_ctree, we suspend the dev_replace, but keep the
replace target around so that we can resume the dev_replace procedure
when we mount the root again. This is the call trace:
close_ctree():
btrfs_dev_replace_suspend_for_unmount();
btrfs_close_devices():
btrfs_close_fs_devices():
btrfs_close_one_device():
ASSERT(!test_bit(BTRFS_DEV_STATE_REPLACE_TGT,
&device->dev_state));
However, since the replace target sticks around, there is a device
with BTRFS_DEV_STATE_REPLACE_TGT set on close, and we fail the
assertion in btrfs_close_one_device.
To fix this, if we come across the replace target device when
closing, we should properly reset it back to allocation state. This
fix also ensures that if a non-target device has a corrupted state and
has the BTRFS_DEV_STATE_REPLACE_TGT bit set, the assertion will still
catch the error.
Reported-by: David Sterba <dsterba@suse.com>
Fixes: b2a6166768 ("btrfs: fix rw device counting in __btrfs_free_extra_devids")
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aaedb9e00e upstream.
Since a few kernel releases the Pogoplug 4 has crashed like this
during boot:
Unable to handle kernel NULL pointer dereference at virtual address 00000002
(...)
[<c04116ec>] (strlen) from [<c00ead80>] (kstrdup+0x1c/0x4c)
[<c00ead80>] (kstrdup) from [<c04591d8>] (__clk_register+0x44/0x37c)
[<c04591d8>] (__clk_register) from [<c04595ec>] (clk_hw_register+0x20/0x44)
[<c04595ec>] (clk_hw_register) from [<c045bfa8>] (__clk_hw_register_mux+0x198/0x1e4)
[<c045bfa8>] (__clk_hw_register_mux) from [<c045c050>] (clk_register_mux_table+0x5c/0x6c)
[<c045c050>] (clk_register_mux_table) from [<c0acf3e0>] (kirkwood_clk_muxing_setup.constprop.0+0x13c/0x1ac)
[<c0acf3e0>] (kirkwood_clk_muxing_setup.constprop.0) from [<c0aceae0>] (of_clk_init+0x12c/0x214)
[<c0aceae0>] (of_clk_init) from [<c0ab576c>] (time_init+0x20/0x2c)
[<c0ab576c>] (time_init) from [<c0ab3d18>] (start_kernel+0x3dc/0x56c)
[<c0ab3d18>] (start_kernel) from [<00000000>] (0x0)
Code: e3130020 1afffffb e12fff1e c08a1078 (e5d03000)
This is because the "powersave" mux clock 0 was provided in an unterminated
array, which is required by the loop in the driver:
/* Count, allocate, and register clock muxes */
for (n = 0; desc[n].name;)
n++;
Here n will go out of bounds and then call clk_register_mux() on random
memory contents after the mux clock.
Fix this by terminating the array with a blank entry.
Fixes: 105299381d ("cpufreq: kirkwood: use the powersave multiplexer")
Cc: stable@vger.kernel.org
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210814235514.403426-1-linus.walleij@linaro.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79fad92f2e upstream.
Currently there are (at least) two problems in the way pwm_bl starts
managing the enable_gpio pin. Both occur when the backlight is initially
off and the driver finds the pin not already in output mode and, as a
result, unconditionally switches it to output-mode and asserts the signal.
Problem 1: This could cause the backlight to flicker since, at this stage
in driver initialisation, we have no idea what the PWM and regulator are
doing (an unconfigured PWM could easily "rest" at 100% duty cycle).
Problem 2: This will cause us not to correctly honour the
post_pwm_on_delay (which also risks flickers).
Fix this by moving the code to configure the GPIO output mode until after
we have examines the handover state. That allows us to initialize
enable_gpio to off if the backlight is currently off and on if the
backlight is on.
Cc: stable@vger.kernel.org
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8510505d55 upstream.
MD5 is a weak digest algorithm that shouldn't be used for cryptographic
operation. It hinders the efficiency of a patch set that aims to limit
the digests allowed for the extended file attribute namely security.ima.
MD5 is no longer a requirement for IMA, nor should it be used there.
The sole place where we still use the MD5 algorithm inside IMA is setting
the ima_hash algorithm to MD5, if the user supplies 'ima_hash=md5'
parameter on the command line. With commit ab60368ab6 ("ima: Fallback
to the builtin hash algorithm"), setting "ima_hash=md5" fails gracefully
when CRYPTO_MD5 is not set:
ima: Can not allocate md5 (reason: -2)
ima: Allocating md5 failed, going to use default hash algorithm sha256
Remove the CRYPTO_MD5 dependency for IMA.
Signed-off-by: THOBY Simon <Simon.THOBY@viveris.fr>
Reviewed-by: Lakshmi Ramasubramanian <nramas@linux.microsoft.com>
[zohar@linux.ibm.com: include commit number in patch description for
stable.]
Cc: stable@vger.kernel.org # 4.17
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9130a2dfd upstream.
When MSR_IA32_TSC_ADJUST is written by guest due to TSC ADJUST feature
especially there's a big tsc warp (like a new vCPU is hot-added into VM
which has been up for a long time), tsc_offset is added by a large value
then go back to guest. This causes system time jump as tsc_timestamp is
not adjusted in the meantime and pvclock monotonic character.
To fix this, just notify kvm to update vCPU's guest time before back to
guest.
Cc: stable@vger.kernel.org
Signed-off-by: Zelin Deng <zelin.deng@linux.alibaba.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1619576521-81399-2-git-send-email-zelin.deng@linux.alibaba.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 527f721478 upstream.
The recent commit
064855a690 ("x86/resctrl: Fix default monitoring groups reporting")
caused a RHEL build failure with an uninitialized variable warning
treated as an error because it removed the default case snippet.
The RHEL Makefile uses '-Werror=maybe-uninitialized' to force possibly
uninitialized variable warnings to be treated as errors. This is also
reported by smatch via the 0day robot.
The error from the RHEL build is:
arch/x86/kernel/cpu/resctrl/monitor.c: In function ‘__mon_event_count’:
arch/x86/kernel/cpu/resctrl/monitor.c:261:12: error: ‘m’ may be used
uninitialized in this function [-Werror=maybe-uninitialized]
m->chunks += chunks;
^~
The upstream Makefile does not build using '-Werror=maybe-uninitialized'.
So, the problem is not seen there. Fix the problem by putting back the
default case snippet.
[ bp: note that there's nothing wrong with the code and other compilers
do not trigger this warning - this is being done just so the RHEL compiler
is happy. ]
Fixes: 064855a690 ("x86/resctrl: Fix default monitoring groups reporting")
Reported-by: Terry Bowman <Terry.Bowman@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/162949631908.23903.17090272726012848523.stgit@bmoger-ubuntu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb2853a6a4 upstream.
The ops->receive_buf() may be accessed concurrently from these two
functions. If the driver flushes data to the line discipline
receive_buf() method while tiocsti() is waiting for the
ops->receive_buf() to finish its work, the data race will happen.
For example:
tty_ioctl |tty_ldisc_receive_buf
->tioctsi | ->tty_port_default_receive_buf
| ->tty_ldisc_receive_buf
->hci_uart_tty_receive | ->hci_uart_tty_receive
->h4_recv | ->h4_recv
In this case, the h4 receive buffer will be overwritten by the
latecomer, and we will lost the data.
Hence, change tioctsi() function to use the exclusive lock interface
from tty_buffer to avoid the data race.
Reported-by: syzbot+97388eb9d31b997fe1d0@syzkaller.appspotmail.com
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Link: https://lore.kernel.org/r/20210823000641.2082292-1-phind.uet@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 064c734986 upstream.
The stat() family of syscalls report the wrong size for encrypted
symlinks, which has caused breakage in several userspace programs.
Fix this by calling fscrypt_symlink_getattr() after ubifs_getattr() for
encrypted symlinks. This function computes the correct size by reading
and decrypting the symlink target (if it's not already cached).
For more details, see the commit which added fscrypt_symlink_getattr().
Fixes: ca7f85be8d ("ubifs: Add support for encrypted symlinks")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210702065350.209646-5-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 461b43a8f9 upstream.
The stat() family of syscalls report the wrong size for encrypted
symlinks, which has caused breakage in several userspace programs.
Fix this by calling fscrypt_symlink_getattr() after f2fs_getattr() for
encrypted symlinks. This function computes the correct size by reading
and decrypting the symlink target (if it's not already cached).
For more details, see the commit which added fscrypt_symlink_getattr().
Fixes: cbaf042a3c ("f2fs crypto: add symlink encryption")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210702065350.209646-4-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c4bca10ce upstream.
The stat() family of syscalls report the wrong size for encrypted
symlinks, which has caused breakage in several userspace programs.
Fix this by calling fscrypt_symlink_getattr() after ext4_getattr() for
encrypted symlinks. This function computes the correct size by reading
and decrypting the symlink target (if it's not already cached).
For more details, see the commit which added fscrypt_symlink_getattr().
Fixes: f348c25232 ("ext4 crypto: add symlink encryption")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210702065350.209646-3-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d187605605 upstream.
Add a helper function fscrypt_symlink_getattr() which will be called
from the various filesystems' ->getattr() methods to read and decrypt
the target of encrypted symlinks in order to report the correct st_size.
Detailed explanation:
As required by POSIX and as documented in various man pages, st_size for
a symlink is supposed to be the length of the symlink target.
Unfortunately, st_size has always been wrong for encrypted symlinks
because st_size is populated from i_size from disk, which intentionally
contains the length of the encrypted symlink target. That's slightly
greater than the length of the decrypted symlink target (which is the
symlink target that userspace usually sees), and usually won't match the
length of the no-key encoded symlink target either.
This hadn't been fixed yet because reporting the correct st_size would
require reading the symlink target from disk and decrypting or encoding
it, which historically has been considered too heavyweight to do in
->getattr(). Also historically, the wrong st_size had only broken a
test (LTP lstat03) and there were no known complaints from real users.
(This is probably because the st_size of symlinks isn't used too often,
and when it is, typically it's for a hint for what buffer size to pass
to readlink() -- which a slightly-too-large size still works for.)
However, a couple things have changed now. First, there have recently
been complaints about the current behavior from real users:
- Breakage in rpmbuild:
https://github.com/rpm-software-management/rpm/issues/1682https://github.com/google/fscrypt/issues/305
- Breakage in toybox cpio:
https://www.mail-archive.com/toybox@lists.landley.net/msg07193.html
- Breakage in libgit2: https://issuetracker.google.com/issues/189629152
(on Android public issue tracker, requires login)
Second, we now cache decrypted symlink targets in ->i_link. Therefore,
taking the performance hit of reading and decrypting the symlink target
in ->getattr() wouldn't be as big a deal as it used to be, since usually
it will just save having to do the same thing later.
Also note that eCryptfs ended up having to read and decrypt symlink
targets in ->getattr() as well, to fix this same issue; see
commit 3a60a1686f ("eCryptfs: Decrypt symlink target for stat size").
So, let's just bite the bullet, and read and decrypt the symlink target
in ->getattr() in order to report the correct st_size. Add a function
fscrypt_symlink_getattr() which the filesystems will call to do this.
(Alternatively, we could store the decrypted size of symlinks on-disk.
But there isn't a great place to do so, and encryption is meant to hide
the original size to some extent; that property would be lost.)
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210702065350.209646-2-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dce224f46 upstream.
__peernet2id() can be protected by RCU as it only calls idr_for_each(),
which is RCU-safe, and never modifies the nsid table.
rtnl_net_dumpid() can also do lockless lookups. It does two nested
idr_for_each() calls on nsid tables (one direct call and one indirect
call because of rtnl_net_dumpid_one() calling __peernet2id()). The
netnsid tables are never updated. Therefore it is safe to not take the
nsid_lock and run within an RCU-critical section instead.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
[ Upstream commit 92548b0ee2 ]
The UDP length field should be in network order.
This removes the following sparse error:
net/ipv4/route.c:3173:27: warning: incorrect type in assignment (different base types)
net/ipv4/route.c:3173:27: expected restricted __be16 [usertype] len
net/ipv4/route.c:3173:27: got unsigned long
Fixes: 404eb77ea7 ("ipv4: support sport, dport and ip_proto in RTM_GETROUTE")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 429205da6c ]
Based on tests the QCA7000 doesn't support checksum offloading. So assume
ip_summed is CHECKSUM_NONE and let the kernel take care of the checksum
handling. This fixes data transfer issues in noisy environments.
Reported-by: Michael Heimpold <michael.heimpold@in-tech.com>
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67d6d681e1 ]
Even after commit 6457378fe7 ("ipv4: use siphash instead of Jenkins in
fnhe_hashfun()"), an attacker can still use brute force to learn
some secrets from a victim linux host.
One way to defeat these attacks is to make the max depth of the hash
table bucket a random value.
Before this patch, each bucket of the hash table used to store exceptions
could contain 6 items under attack.
After the patch, each bucket would contains a random number of items,
between 6 and 10. The attacker can no longer infer secrets.
This is slightly increasing memory size used by the hash table,
by 50% in average, we do not expect this to be a problem.
This patch is more complex than the prior one (IPv6 equivalent),
because IPv4 was reusing the oldest entry.
Since we need to be able to evict more than one entry per
update_or_create_fnhe() call, I had to replace
fnhe_oldest() with fnhe_remove_oldest().
Also note that we will queue extra kfree_rcu() calls under stress,
which hopefully wont be a too big issue.
Fixes: 4895c771c7 ("ipv4: Add FIB nexthop exceptions.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Keyu Man <kman001@ucr.edu>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: David Ahern <dsahern@kernel.org>
Tested-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b63aed3ff1 ]
kmemleak reported that dev_name() of internally-handled cores were leaked
on driver unbinding. Let's use device_initialize() to take refcounts for
them and put_device() to properly free the related stuff.
While looking at it, there's another potential issue for those which should
be *registered* into driver core. If device_register() failed, we put
device once and freed bcma_device structures. In bcma_unregister_cores(),
they're treated as unregistered and we hit both UAF and double-free. That
smells not good and has also been fixed now.
Fixes: ab54bc8460 ("bcma: fill core details for every device")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210727025232.663-2-yuzenghui@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4720f1bf4e ]
ehci_orion_drv_probe() did not account for possible errors of
clk_prepare_enable() that in particular could cause invocation of
clk_disable_unprepare() on clocks that were not prepared/enabled yet,
e.g. in remove or on handling errors of usb_add_hcd() in probe. Though,
there were several patches fixing different issues with clocks in this
driver, they did not solve this problem.
Add handling of errors of clk_prepare_enable() in ehci_orion_drv_probe()
to avoid calls of clk_disable_unprepare() without previous successful
invocation of clk_prepare_enable().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 8c869edaee ("ARM: Orion: EHCI: Add support for enabling clocks")
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Link: https://lore.kernel.org/r/20210825170902.11234-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f980d055a0 ]
strlcpy() reads the entire source buffer first. This read may exceed the
destination size limit. This is both inefficient and can lead to linear
read overflows if a source string is not NUL-terminated.
Also, the strnlen() call does not avoid the read overflow in the strlcpy
function when a not NUL-terminated string is passed.
So, replace this block by a call to kstrndup() that avoids this type of
overflow and does the same.
Fixes: 066ce68994 ("cifs: rename cifs_strlcpy_to_host and make it use new functions")
Signed-off-by: Len Baker <len.baker@gmx.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6840a5e37 ]
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: e0d1ec9785 ("i2c-s3c2410: Change IRQ to be plain integer.")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a129950516 ]
When adding the code to handle platform_get_irq*() errors in the commit
489447380a ("handle errors returned by platform_get_irq*()"), the
actual error code was enforced to be -ENXIO in the driver for some
strange reason. This didn't matter much until the deferred probing was
introduced -- which requires an actual error code to be propagated
upstream from the failure site.
While fixing this, also stop overriding the errors from request_irq() to
-EIO (done since the pre-git era).
Fixes: 489447380a ("[PATCH] handle errors returned by platform_get_irq*()")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f41a4b2b5e ]
Syzbot hit "task hung" bug in hci_req_sync(). The problem was in
unreasonable huge inquiry timeout passed from userspace.
Fix it by adding sanity check for timeout value to hci_inquiry().
Since hci_inquiry() is the only user of hci_req_sync() with user
controlled timeout value, it makes sense to check timeout value in
hci_inquiry() and don't touch hci_req_sync().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-and-tested-by: syzbot+be2baed593ea56c6a84c@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2af0c5ffad ]
If IRQ occurs between calling request_irq() and mv_u3d_eps_init(),
then null pointer dereference occurs since u3d->eps[] wasn't
initialized yet but used in mv_u3d_nuke().
The patch puts registration of the interrupt handler after
initializing of neccesery data.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 90fccb529d ("usb: gadget: Gadget directory cleanup - group UDC drivers")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210818141247.4794-1-lutovinova@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d45a1373e ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_threaded_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding an
original error code. Stop calling request_threaded_irq() with the invalid
IRQ #s.
Fixes: 9ba96ae507 ("usb: omap1: Tahvo USB transceiver driver")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/8280d6a4-8e9a-7cfe-1aa9-db586dc9afdf@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ea53674d0 ]
Commit 0ea9fd001a ("Bluetooth: Shutdown controller after workqueues
are flushed or cancelled") introduced a regression that makes mtkbtsdio
driver stops working:
[ 36.593956] Bluetooth: hci0: Firmware already downloaded
[ 46.814613] Bluetooth: hci0: Execution of wmt command timed out
[ 46.814619] Bluetooth: hci0: Failed to send wmt func ctrl (-110)
The shutdown callback depends on the result of hdev->rx_work, so we
should call it before flushing rx_work:
-> btmtksdio_shutdown()
-> mtk_hci_wmt_sync()
-> __hci_cmd_send()
-> wait for BTMTKSDIO_TX_WAIT_VND_EVT gets cleared
-> btmtksdio_recv_event()
-> hci_recv_frame()
-> queue_work(hdev->workqueue, &hdev->rx_work)
-> clears BTMTKSDIO_TX_WAIT_VND_EVT
So move the shutdown callback before flushing TX/RX queue to resolve the
issue.
Reported-and-tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Fixes: 0ea9fd001a ("Bluetooth: Shutdown controller after workqueues are flushed or cancelled")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
