Ensure that the register is aligned to a dword, otherwise the read could
read out-of-range data.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This has been replaced by the new and much better VIDIOC_DBG_G_CHIP_INFO.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
From Christian Daudt:
* 'armsoc/for-3.11/cleanups' of git://github.com/broadcom/bcm11351:
ARM: bcm281xx: Remove init_irq declaration in machine description
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This function is no longer needed since it is now the responsibility of the
v4l2 core to check if the DBG_G/S_REGISTER and DBG_G_CHIP_INFO ioctls are
called for the bridge driver or not.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
From Christian Daudt:
* 'armsoc/for-3.11/dt' of git://github.com/broadcom/bcm11351:
ARM: dts: bcm281xx: change comment to C89 style
ARM: mmc: bcm281xx SDHCI driver (dt mods)
ARM: dts: bcm281xx: use existing defines for irqs
ARM: dts: bcm281xx: use #include for device tree files
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove g_chip_ident from cx88. Also remove the v4l2-chip-ident.h include.
The board code used defines from v4l2-chip-ident.h to tell the driver which
audio chip is used. Replace this with a cx88-specific enum.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
From Simon Horman:
Second Round of Renesas ARM-based SoC DT updates for v3.11
* Increased DT coverage for renesas-intc-irqpin
by Guennadi Liakhovetski
* Clean up of address format used in sh73a0 dtsi file
by Guennadi Liakhovetski
* tag 'renesas-dt2-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: irqpin: add a DT property to enable masking on parent
ARM: shmobile: sh73a0: remove "0x" prefix from DT node names
irqchip: renesas-intc-irqpin: DT binding for sense bitfield width
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Simon Horman:
Second Round of Renesas ARM based SoC GPIO R-Car updates for v3.11
Documentation enhancement and code cleanup by Laurent Pinchart.
* tag 'renesas-gpio-rcar2-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
gpio-rcar: Remove #ifdef CONFIG_OF around OF-specific sections
gpio-rcar: Reference core gpio documentation in the DT bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Simon Horman:
Second Round of Renesas ARM based SoC pinmux and GPIO update for v3.11
tidyup MMC_D1 pin for r8a7778 SoC
fix two pin numbers and add HSCIF pin groups to r8a7790 SoC
add pinmux data for MMCIF and SDHI interfaces for r8a73a4 SoC
* tag 'renesas-pinmux2-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
sh-pfc: r8a7778: tidyup MMC_D1 pin
pinctrl: r8a7790: fix two pin numbers
sh-pfc: r8a7790: add HSCIF pin groups
pinctrl: r8a73a4: add pinmux data for MMCIF and SDHI interfaces
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Simon Horman:
Second Round of Renesas ARM-based SoC board updates for v3.11
* Extended hardware coverage for the Bock-W board
by Goda-san and Morimoto-san
* Correction to Ether device name for the Bock-W board
from Sergei Shtylyov
* tag 'renesas-boards2-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: BOCK-W: change Ether device name
ARM: shmobile: bockw: add MMCIF support
ARM: shmobile: bockw: add SPI FLASH support
ARM: shmobile: bockw: add I2C device support
ARM: shmobile: BOCK-W: add Ether support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Kukjin Kim:
based on tags/common-clk-audio
- add support for exynos5420 SoC
* tag 'soc-exynos5420-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: extend soft-reset support for EXYNOS5420
ARM: EXYNOS: add secondary CPU boot base location for EXYNOS5420
clocksource: exynos_mct: use (request/free)_irq calls for local timer registration
ARM: dts: Add initial device tree support for EXYNOS5420
clk: exynos5420: register clocks using common clock framework
ARM: EXYNOS: use four additional chipid bits to identify EXYNOS family
serial: samsung: select EXYNOS specific driver data if ARCH_EXYNOS is defined
ARM: EXYNOS: Add support for EXYNOS5420 SoC
ARM: dts: list the CPU nodes for EXYNOS5250
ARM: dts: fork out common EXYNOS5 nodes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Simon Horman:
Renesas ARM based SoC boot cleanup for v3.11
Work by Magnus Damm and others to clean up the boot of and move
things closer to supporting multi-arch.
As a side effect of this work it was decided to remove support for
two boards, Bonito and AP4EVB. Those patches are included in this
series as they depend on earlier patches in the series.
* tag 'renesas-cleanup-boot-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove Bonito board support
ARM: shmobile: Remove AP4EVB board support
ARM: shmobile: Remove mach/memory.h
ARM: shmobile: Remove MEMORY_START/SIZE
ARM: shmobile: Enable ARM_PATCH_PHYS_VIRT
ARM: shmobile: Remove old SCU boot code
ARM: shmobile: EMEV2 SMP with SCU boot fn and args
ARM: shmobile: sh73a0 SMP with SCU boot fn and args
ARM: shmobile: r8a7779 SMP with SCU boot fn and args
ARM: shmobile: Add SCU boot function using argument
ARM: shmobile: Add SMP boot function and argument
ARM: shmobile: Rework sh7372 sleep code to use virt_to_phys()
ARM: shmobile: Remove romImage CONFIG_MEMORY_START
ARM: shmobile: Let romImage rely on default ATAGS
ARM: shmobile: uImage load address rework
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Simon Horman:
Renesas ARM based SoC cleanups for v3.11
__initdata annotations for the r8a7790 SoC by Morimoto-san.
* tag 'renesas-cleanup-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (158 commits)
ARM: shmobile: r8a7790: add __initdata on resource and device data
Based on 'renesas-pinmux-for-v3.11' and 'renesas-soc-for-v3.11
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Patches from Lee Jones:
This gets rid of mop500_snowball_ethernet_clock_enable() which is no
longer in use. It also straightens out a bug which ensures the SMSC911x's
regulator is turned on at start-up when using Device Tree.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mop500_snowball_ethernet_clock_enable() provided a means to enable a
clock which was used for the SMSC911x Ethernet device on Snowball. It
was merely a stand-in until the driver was common clk compliant. Now
that it is, this can be removed for both DT and ATAGs booting.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
When this node was added, the AB8500 GPIO driver was pretty broken.
As a hack, we pretended that NOMADIK GPIO 26 was the correct on/off
pin, as it was unused. It worked because AB8500 GPIO 26 was in an
'always on from boot' state. Now the AB8500 GPIO driver is working,
the default state for all the pins is 'off'. Let's flip back over to
use the correct GPIO which is _actually_ attached to the regulator.
We're also taking the opportunity to straighten out some formatting
misdemeanours, swapping spaces for tabs.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Here we're adding a node for the AB8500 GPIO device. This will allow
other DT:ed components to obtain GPIOs for use within their drivers.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
In sound/usb/card.c and sound/usb/misc/ua101.c there are no spaces
between the vendor and the device names, use this style in the other
drivers too.
This also helps keeping consistency when new drivers copies from the
ones already in the mainline tree.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For USB devices it's not necessary to allocate physically contiguous
buffers.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For USB devices it's not necessary to allocate physically contiguous
buffers.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd_card_used variable is only read but never written, remove it.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This code is older than git, and I haven't tested it, but if size ==
SIZE_MAX_STATUS then we would write one space past the end of the
rmh->Stat[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
More than 256 entries in ACPI MADT is supported from ACPI 3.0, so the
information in should be Documentation/cpu-hotplug.txt updated.
[rjw: Changelog]
Suggested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The recent modification in the cpuidle framework consolidated the
timer broadcast code across the different drivers by setting a new
flag in the idle state. It tells the cpuidle core code to enter/exit
the broadcast mode for the cpu when entering a deep idle state. The
broadcast timer enter/exit is no longer handled by the back-end
driver.
This change made the local interrupt to be enabled *before* calling
CLOCK_EVENT_NOTIFY_EXIT.
On a tegra114, a four cores system, when the flag has been introduced
in the driver, the following warning appeared:
WARNING: at kernel/time/tick-broadcast.c:578 tick_broadcast_oneshot_control
CPU: 2 PID: 0 Comm: swapper/2 Not tainted 3.10.0-rc3-next-20130529+ #15
[<c00667f8>] (tick_broadcast_oneshot_control+0x1a4/0x1d0) from [<c0065cd0>] (tick_notify+0x240/0x40c)
[<c0065cd0>] (tick_notify+0x240/0x40c) from [<c0044724>] (notifier_call_chain+0x44/0x84)
[<c0044724>] (notifier_call_chain+0x44/0x84) from [<c0044828>] (raw_notifier_call_chain+0x18/0x20)
[<c0044828>] (raw_notifier_call_chain+0x18/0x20) from [<c00650cc>] (clockevents_notify+0x28/0x170)
[<c00650cc>] (clockevents_notify+0x28/0x170) from [<c033f1f0>] (cpuidle_idle_call+0x11c/0x168)
[<c033f1f0>] (cpuidle_idle_call+0x11c/0x168) from [<c000ea94>] (arch_cpu_idle+0x8/0x38)
[<c000ea94>] (arch_cpu_idle+0x8/0x38) from [<c005ea80>] (cpu_startup_entry+0x60/0x134)
[<c005ea80>] (cpu_startup_entry+0x60/0x134) from [<804fe9a4>] (0x804fe9a4)
I don't have the hardware, so I wasn't able to reproduce the warning
but after looking a while at the code, I deduced the following:
1. the CPU2 enters a deep idle state and sets the broadcast timer
2. the timer expires, the tick_handle_oneshot_broadcast function is
called, setting the tick_broadcast_pending_mask and waking up the
idle cpu CPU2
3. the CPU2 exits idle handles the interrupt and then invokes
tick_broadcast_oneshot_control with CLOCK_EVENT_NOTIFY_EXIT which
runs the following code:
[...]
if (dev->next_event.tv64 == KTIME_MAX)
goto out;
if (cpumask_test_and_clear_cpu(cpu,
tick_broadcast_pending_mask))
goto out;
[...]
So if there is no next event scheduled for CPU2, we fulfil the
first condition and jump out without clearing the
tick_broadcast_pending_mask.
4. CPU2 goes to deep idle again and calls
tick_broadcast_oneshot_control with CLOCK_NOTIFY_EVENT_ENTER but
with the tick_broadcast_pending_mask set for CPU2, triggering the
warning.
The issue only surfaced due to the modifications of the cpuidle
framework, which resulted in interrupts being enabled before the call
to the clockevents code. If the call happens before interrupts have
been enabled, the warning cannot trigger, because there is still the
event pending which caused the broadcast timer expiry.
Move the check for the next event below the check for the pending bit,
so the pending bit gets cleared whether an event is scheduled on the
cpu or not.
[ tglx: Massaged changelog ]
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reported-and-tested-by: Joseph Lo <josephl@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linaro-kernel@lists.linaro.org
Link: http://lkml.kernel.org/r/1371485735-31249-1-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* Don't leak random kernel memory to EFI variable NVRAM when attempting
to initiate garbage collection. Also, free the kernel memory when
we're done with it instead of leaking - Ben Hutchings
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Currently the max8973 regulator driver uses a single static struct of
regulator operations for all chip instances, but can overwrite some of its
members depending on configuration. This will affect all other MAX8973
instances on the system. This patch fixes this bug by allocating a separate
copy of the struct for each chip instance.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
1. Check for allocation failure
2. Clear the buffer contents, as they may actually be written to flash
3. Don't leak the buffer
Compile-tested only.
[ Tested successfully on my buggy ASUS machine - Matt ]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
From Heiko Stuebner:
Adds basic support for Rockchip Cortex-A9 SoCs.
* tag 'v3.11-rockchip-basics' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
clocksource: dw_apb_timer_of: use clocksource_of_init
clocksource: dw_apb_timer_of: select DW_APB_TIMER
clocksource: dw_apb_timer_of: add clock-handling
clocksource: dw_apb_timer_of: enable the use the clocksource as sched clock
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Timer Pulse Unit (TPU) is a 4-channels 16-bit timer used to generate
waveforms. This driver exposes PWM functions through the PWM API for
other drivers to use.
The code is loosely based on the leds-renesas-tpu driver by Magnus Damm
and the TPU PWM driver shipped in the Armadillo EVA 800 kernel sources.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add a simple sysfs interface to the generic PWM framework.
/sys/class/pwm/
`-- pwmchipN/ for each PWM chip
|-- export (w/o) ask the kernel to export a PWM channel
|-- npwm (r/o) number of PWM channels in this PWM chip
|-- pwmX/ for each exported PWM channel
| |-- duty_cycle (r/w) duty cycle (in nanoseconds)
| |-- enable (r/w) enable/disable PWM
| |-- period (r/w) period (in nanoseconds)
| `-- polarity (r/w) polarity of PWM (normal/inversed)
`-- unexport (w/o) return a PWM channel to the kernel
Based on work by Lars Poeschel.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This adds a generic devicetree board file and a dtsi for boards
based on the RK3066a SoCs from Rockchip.
Apart from the generic parts (gic, clocks, pinctrl) the only components
currently supported are the timers, uarts and mmc ports (all DesignWare-
based).
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Olof Johansson <olof@lixom.net>
Uarts on all recent Rockchip SoCs are Synopsis DesignWare 8250 types.
Only their addresses vary very much.
This patch adds the necessary definitions to use any of the uart ports
for early debug purposes.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds a basic clock setup for rk3066a SoCs. Only the gates are
set up currently, as the mux and dividers should use the upcoming
generic devicetree bindings.
Clocks whose rates need to be known are supplied by fixed-rate
"dummy"-clocks that provide the correct rate. This is uncritical insofar
that the only bootloader currently in existence for Rockchip devices
is the propietary Rockchip one that always setups the clocks in the
necessary way.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
This patch adds unaligned buffer tests for hashes.
The first new test is with one byte offset and the second test checks if
cra_alignmask for driver is big enough; for example, for testing a case
where cra_alignmask is set to 7, but driver really needs buffers to be
aligned to 16 bytes.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds unaligned buffer tests for AEADs.
The first new test is with one byte offset and the second test checks if
cra_alignmask for driver is big enough; for example, for testing a case
where cra_alignmask is set to 7, but driver really needs buffers to be
aligned to 16 bytes.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds unaligned buffer tests for blkciphers.
The first new test is with one byte offset and the second test checks if
cra_alignmask for driver is big enough; for example, for testing a case
where cra_alignmask is set to 7, but driver really needs buffers to be
aligned to 16 bytes.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Patch adds check for alg_test_descs list order, so that accidentically
misplaced entries are found quicker. Duplicate entries are also checked for.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This reverts commit cf1521a1a5.
Instruction (vpgatherdd) that this implementation relied on turned out to be
slow performer on real hardware (i5-4570). The previous 8-way twofish/AVX
implementation is therefore faster and this implementation should be removed.
Converting this implementation to use the same method as in twofish/AVX for
table look-ups would give additional ~3% speed up vs twofish/AVX, but would
hardly be worth of the added code and binary size.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This reverts commit 6048801070.
Instruction (vpgatherdd) that this implementation relied on turned out to be
slow performer on real hardware (i5-4570). The previous 4-way blowfish
implementation is therefore faster and this implementation should be removed.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add implementation tuned for more performance on real hardware. Changes are
mostly around the part mixing 128-bit extract and insert instructions and
AES-NI instructions. Also 'vpbroadcastb' instructions have been change to
'vpshufb with zero mask'.
Tests on Intel Core i5-4570:
tcrypt ECB results, old-AVX2 vs new-AVX2:
size 128bit key 256bit key
enc dec enc dec
256 1.00x 1.00x 1.00x 1.00x
1k 1.08x 1.09x 1.05x 1.06x
8k 1.06x 1.06x 1.06x 1.06x
tcrypt ECB results, AVX vs new-AVX2:
size 128bit key 256bit key
enc dec enc dec
256 1.00x 1.00x 1.00x 1.00x
1k 1.51x 1.50x 1.52x 1.50x
8k 1.47x 1.48x 1.48x 1.48x
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Report AF_IB source and destination addresses through netlink
interface.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Allow user space applications to join multicast groups using MGIDs
directly. MGIDs may be passed using AF_IB addresses. Since the
current multicast join command only supports addresses as large as
sockaddr_in6, define a new structure for joining addresses specified
using sockaddr_ib.
Since AF_IB allows the user to specify the qkey when resolving a
remote UD QP address, when joining the multicast group use the qkey
value, if one has been assigned.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Allow user space applications to call resolve_addr using AF_IB. To
support sockaddr_ib, we need to define a new structure capable of
handling the larger address size.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
