This adds support for the Allwinner A33 thermal sensor.
Unlike the A10, A13 and A31, the Allwinner A33 only has one channel
which is dedicated to the thermal sensor. Moreover, its thermal sensor
does not generate interruptions, thus we only need to directly read the
register storing the temperature value.
The MFD used by the A10, A13 and A31, was created to avoid breaking the
DT binding, but since the nodes for the ADC weren't there for the A33,
it is not needed.
Though the A33 does not have an internal ADC, it has a thermal sensor
which shares the same registers with GPADC of the already supported SoCs
and almost the same bits, for the same purpose (thermal sensor).
The thermal sensor behaves exactly the same (except the presence of
interrupts or not) on the different SoCs.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Since commit b655028795 ("uio: we cannot mmap unaligned page
contents") addresses and sizes of UIO memory regions must be
page-aligned. If the address in the BAR register is not
page-aligned (which is the case of the mf264 card), the mentioned
commit forces the UIO driver to round the address down to the page
size. Then, there is no easy way for user-space to learn the offset of
the actual memory region within the page, because the offset seen in
/sys/class/uio/uio?/maps/map?/offset is calculated from the rounded
address and thus it is always zero.
Fix that problem by including the offset in struct uio_mem. UIO
drivers can set this field and userspace can read its value from
/sys/class/uio/uio?/maps/map?/offset.
The following commits update the uio_mf264 driver to set this new offs
field.
Drivers for hardware with page-aligned BARs need not to be modified
provided that they initialize struct uio_info (which contains uio_mem)
with zeros.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In DEFINE_DEBUGFS_ATTRIBUTE() macro, since we use nonseekable_open() to
open, we should use no_llseek() to seek, not generic_file_llseek().
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding the core functions necessary for a fpga-mgr driver
for the Altera Partial IP component. It is intended for
these functions to be used by the various bus implementations
like the platform bus or the PCIe bus.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Acked-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding timeout for maximum allowed time for FPGA to go to
operating mode after a FPGA region has been programmed.
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newly added header file triggers a sanity check:
usr/include/linux/aspeed-lpc-ctrl.h:44: found __[us]{8,16,32,64} type without #include <linux/types.h>
We should include linux/types.h explicitly to ensure the header
can be included from user space.
Fixes: 6c4e976785 ("drivers/misc: Add Aspeed LPC control driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's rather confusing that the netlink message flags are
numbered 1, 2, 4, 8, 16, 32, <unused>, 0x100. Make that
more understandable by numbering the lower ones with hex
constants as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change undo the change done by 'commit 3bec247474
("iio: hid-sensor-trigger: Change get poll value function order to avoid
sensor properties losing after resume from S3")' as this breaks some
USB/i2c sensor hubs.
Instead of relying on HW for restoring poll and hysteresis, driver stores
and restores on resume (S3). In this way user space modified settings are
not lost for any kind of sensor hub behavior.
In this change, whenever user space modifies sampling frequency or
hysteresis driver will get the feature value from the hub and store in the
per device hid_sensor_common data structure. On resume callback from S3,
system will set the feature to sensor hub, if user space ever modified the
feature value.
Fixes: 3bec247474 ("iio: hid-sensor-trigger: Change get poll value function order to avoid sensor properties losing after resume from S3")
Reported-by: Ritesh Raj Sarraf <rrs@researchut.com>
Tested-by: Ritesh Raj Sarraf <rrs@researchut.com>
Tested-by: Song, Hongyan <hongyan.song@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Saeed Mahameed says:
====================
mlx5-updates-2017-04-16
This patchset provides some updates for the mlx5 drivers.
From Majd,
1st patch, Adds ConnectX-6 and ConnectX-6 VF PCI IDs support.
From Guy,
2nd patch, Adds RXFCS scatter support.
3rd patch, Small cleanup to make a function static.
From Eran,
4th patch, Adds 4 zeros padding to ethtool FW version.
6th patch, Trevial code reuse cleanup
From Inbar,
5th patch, Show board id in ethtool driver information
From Saeed,
7th patch, Set default RX moderation parameters on driver load
as a small fix for the latest fail-safe config feature.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
User space needs to know where the GMEM whole starts so that they
can set up the addressing correctly.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Pull KVM fixes from Radim Krčmář:
"ARM:
- Fix a problem with GICv3 userspace save/restore
- Clarify GICv2 userspace save/restore ABI
- Be more careful in clearing GIC LRs
- Add missing synchronization primitive to our MMU handling code
PPC:
- Check for a NULL return from kzalloc
s390:
- Prevent translation exception errors on valid page tables for the
instruction-exection-protection support
x86:
- Fix Page-Modification Logging when running a nested guest"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Book3S HV: Check for kmalloc errors in ioctl
KVM: nVMX: initialize PML fields in vmcs02
KVM: nVMX: do not leak PML full vmexit to L1
KVM: arm/arm64: vgic: Fix GICC_PMR uaccess on GICv3 and clarify ABI
KVM: arm64: Ensure LRs are clear when they should be
kvm: arm/arm64: Fix locking for kvm_free_stage2_pgd
KVM: s390: remove change-recording override support
arm/arm64: KVM: Take mmap_sem in kvm_arch_prepare_memory_region
arm/arm64: KVM: Take mmap_sem in stage2_unmap_vm
When __{start,end}_ro_after_init is referenced from C code, we run into
the following build errors on blackfin:
kernel/extable.c:169: undefined reference to `__start_ro_after_init'
kernel/extable.c:169: undefined reference to `__end_ro_after_init'
The build error is due to the fact that blackfin is one of the few
arches that prepends an underscore '_' to all symbols defined in C.
Fix this by wrapping __{start,end}_ro_after_init in vmlinux.lds.h with
VMLINUX_SYMBOL(), which adds the necessary prefix for arches that have
HAVE_UNDERSCORE_SYMBOL_PREFIX.
Link: http://lkml.kernel.org/r/1491259387-15869-1-git-send-email-jeyu@redhat.com
Signed-off-by: Jessica Yu <jeyu@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Eddie Kovsky <ewk@edkovsky.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reset controller fixes for v4.11
Fix devm_reset_controller_get_optional to return NULL for non-DT devices,
if the RESET_CONTROLLER Kconfig option is enabled. This fixes probe failures
of the 8250_dw driver on Intel platforms after commit acbdad8dd1 ("serial:
8250_dw: simplify optional reset handling").
* tag 'reset-fixes-for-4.11-2' of git://git.pengutronix.de/git/pza/linux:
reset: add exported __reset_control_get, return NULL if optional
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the support for the 4-bytes tag for DSA port distinguishing inserted
allowing receiving and transmitting the packet via the particular port.
The tag is being added after the source MAC address in the ethernet
header.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Landen Chao <Landen.Chao@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Schedulers need to be informed when a hardware queue is added or removed
at runtime so they can allocate/free per-hardware queue data. So,
replace the blk_mq_sched_init_hctx_data() helper, which only makes sense
at init time, with .init_hctx() and .exit_hctx() hooks.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We've added a considerable amount of fixes for stalls and issues
with the blk-mq scheduling in the 4.11 series since forking
off the for-4.12/block branch. We need to do improvements on
top of that for 4.12, so pull in the previous fixes to make
our lives easier going forward.
Signed-off-by: Jens Axboe <axboe@fb.com>
To improve scalability, if hardware queues are shared, restart
a single hardware queue in round-robin fashion. Rename
blk_mq_sched_restart_queues() to reflect the new semantics.
Remove blk_mq_sched_mark_restart_queue() because this function
has no callers. Remove flag QUEUE_FLAG_RESTART because this
patch removes the code that uses this flag.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Introduce a function that runs a hardware queue unconditionally
after a delay. Note: there is already a function that stops and
restarts a hardware queue after a delay, namely blk_mq_delay_queue().
This function will be used in the next patch in this series.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Long Li <longli@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Power area A2VC0 was removed in revision ES2.0, cfr. R-Car Gen3 Hardware
User's Manual rev. 0.53E.
Hence remove it from the power area table when not running on ES1.x.
This is in line with the goal to:
1. Support both the ES1.x and ES2.0 SoC revisions in a single binary
for now,
2. Make it clear which code supports ES1.x, so it can easily be
identified and removed later, when production SoCs are deemed
ubiquitous.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently only dm and md/raid5 bios trigger
trace_block_bio_complete(). Now that we have bio_chain() and
bio_inc_remaining(), it is not possible, in general, for a driver to
know when the bio is really complete. Only bio_endio() knows that.
So move the trace_block_bio_complete() call to bio_endio().
Now trace_block_bio_complete() pairs with trace_block_bio_queue().
Any bio for which a 'queue' event is traced, will subsequently
generate a 'complete' event.
There are a few cases where completion tracing is not wanted.
1/ If blk_update_request() has already generated a completion
trace event at the 'request' level, there is no point generating
one at the bio level too. In this case the bi_sector and bi_size
will have changed, so the bio level event would be wrong
2/ If the bio hasn't actually been queued yet, but is being aborted
early, then a trace event could be confusing. Some filesystems
call bio_endio() but do not want tracing.
3/ The bio_integrity code interposes itself by replacing bi_end_io,
then restoring it and calling bio_endio() again. This would produce
two identical trace events if left like that.
To handle these, we introduce a flag BIO_TRACE_COMPLETION and only
produce the trace event when this is set.
We address point 1 above by clearing the flag in blk_update_request().
We address point 2 above by only setting the flag when
generic_make_request() is called.
We address point 3 above by clearing the flag after generating a
completion event.
When bio_split() is used on a bio, particularly in blk_queue_split(),
there is an extra complication. A new bio is split off the front, and
may be handle directly without going through generic_make_request().
The old bio, which has been advanced, is passed to
generic_make_request(), so it will trigger a trace event a second
time.
Probably the best result when a split happens is to see a single
'queue' event for the whole bio, then multiple 'complete' events - one
for each component. To achieve this was can:
- copy the BIO_TRACE_COMPLETION flag to the new bio in bio_split()
- avoid generating a 'queue' event if BIO_TRACE_COMPLETION is already set.
This way, the split-off bio won't create a queue event, the original
won't either even if it re-submitted to generic_make_request(),
but both will produce completion events, each for their own range.
So if generic_make_request() is called (which generates a QUEUED
event), then bi_endio() will create a single COMPLETE event for each
range that the bio is split into, unless the driver has explicitly
requested it not to.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The comment for the 'flags' field of 'bio' mentions
"command" which is no longer stored there, and doesn't
mention the bvec pool number, which is.
BIO_RESET_BITS is set in such a way that it would need to be
updated if new bits were added, which is easy to miss.
BVEC_POOL_BITS is larger than needed. The BVEC_POOL_IDX()
ranges from 0 to 6, so 3 bits are sufficient.
This patch make improvements in each of these areas.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
In elevator_switch(), if blk_mq_init_sched() fails, we attempt to fall
back to the original scheduler. However, at this point, we've already
torn down the original scheduler's tags, so this causes a crash. Doing
the fallback like the legacy elevator path is much harder for mq, so fix
it by just falling back to none, instead.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Its value has never changed; we might as well make it part of the ABI instead
of using the return value of KVM_CHECK_EXTENSION(KVM_CAP_COALESCED_MMIO).
Because PPC does not always make MMIO available, the code has to be made
dependent on CONFIG_KVM_MMIO rather than KVM_COALESCED_MMIO_PAGE_OFFSET.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Legacy device assignment has been deprecated since 4.2 (released
1.5 years ago). VFIO is better and everyone should have switched to it.
If they haven't, this should convince them. :)
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add and use nfnl_msg_type() function to replace opencoded nfnetlink
message type. I suggested this change, Arushi Singhal made an initial
patch to address this but was missing several spots.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Some drivers can't support all features in all configurations. At the
moment we blindly set FEATURES_OK and later FAILED. Support this better
by adding a callback drivers can use to do some early checks.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently, the GPIO interface is said to Open Drain if it is Single
Ended and active LOW. Similarly, it is said as Open Source if it is
Single Ended and active HIGH.
The active HIGH/LOW is used in the interface for setting the pin
state to HIGH or LOW when enabling/disabling the interface.
In Open Drain interface, pin is set to HIGH by putting pin in
high impedance and LOW by driving to the LOW.
In Open Source interface, pin is set to HIGH by driving pin to
HIGH and set to LOW by putting pin in high impedance.
With above, the Open Drain/Source is unrelated to the active LOW/HIGH
in interface. There is interface where the enable/disable of interface
is ether active LOW or HIGH but it is Open Drain type.
Hence decouple the Open Drain with Single Ended + Active LOW and
Open Source with Single Ended + Active HIGH.
Adding different flag for the Open Drain/Open Source which is valid
only when Single ended flag is enabled.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch refines the definition of AZX_MLCTL_SPA and AZX_MLCTL_CPA
and add more definitions of ML registers
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recent pinctrl changes to allow dynamic allocation of pins exposed one
more issue with the pinctrl pins claimed early by the controller itself.
This caused a regression for IMX6 pinctrl hogs.
Before enabling the pin controller driver we need to wait until it has
been properly initialized, then claim the hogs, and only then enable it.
To fix the regression, split the code into pinctrl_claim_hogs() and
pinctrl_enable(). And then let's require that pinctrl_enable() is always
called by the pin controller driver when ready after calling
pinctrl_register_and_init().
Depends-on: 950b0d91dc ("pinctrl: core: Fix regression caused by delayed
work for hogs")
Fixes: df61b366af26 ("pinctrl: core: Use delayed work for hogs")
Fixes: e566fc11ea ("pinctrl: imx: use generic pinctrl helpers for
managing groups")
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Mika Penttilä <mika.penttila@nextfour.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Gary Bisson <gary.bisson@boundarydevices.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for rx-fcs flag from ethtool.
In case this flag is set, update all RQs to scatter the FCS data into
the packet.
Signed-off-by: Guy Ergas <guye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Now that management firmware is capable of telling us the number of CQs
available for a given PF, qed needs to communicate the number to qedi
so it would know have many to use.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells says:
====================
rxrpc: Miscellany
Here's a set of patches that make some minor changes to AF_RXRPC:
(1) Store error codes in struct rxrpc_call::error as negative codes and
only convert to positive in recvmsg() to avoid confusion inside the
kernel.
(2) Note the result of trying to abort a call (this fails if the call is
already 'completed').
(3) Don't abort on temporary errors whilst processing challenge and
response packets, but rather drop the packet and wait for
retransmission.
And also adds some more tracing:
(4) Protocol errors.
(5) Received abort packets.
(6) Changes in the Rx window size due to ACK packet information.
(7) Client call initiation (to allow the rxrpc_call struct pointer, the
wire call ID and the user ID/afs_call pointer to be cross-referenced).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers have a common pattern of searching the OF graph for either an
attached panel or bridge and then finding the DRM struct for the panel
or bridge. Also, most drivers need to handle deferred probing when the
DRM device is not yet instantiated. Create a common function,
drm_of_find_panel_or_bridge, to find the connected node and the
associated DRM panel or bridge device.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
[seanpaul dropped extern from drm_of.h]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
For drm_of_find_panel_or_bridge() added in the next commit, an empty
version of of_drm_find_panel is needed for !CONFIG_DRM_PANEL.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Currently we use a flag to change behavior in atomic commit
whether a conflicting encoder should be enabled or disabled.
This is used for the legacy set_config helper, which disables
connectors that have a conflicting encoder but not part of the
active crtc list.
There's no need for this to be handled in atomic commit, it
could be done in the set_config helper instead. This will
let the atomic check function reject any conflicting encoders,
while set_config can disable conflicting crtc's. This makes it
possible to recalculate the changed flags in 1 loop.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1491477543-31257-2-git-send-email-maarten.lankhorst@linux.intel.com
A new function, kernel_sock_ip_overhead(), is provided
to calculate the cumulative overhead imposed by the IP
Header and IP options, if any, on a socket's payload.
The new function returns an overhead of zero for sockets
that do not belong to the IPv4 or IPv6 address families.
This is used in the L2TP code path to compute the
total outer IP overhead on the L2TP tunnel socket when
calculating the default MTU for Ethernet pseudowires.
Signed-off-by: R. Parameswaran <rparames@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c7e2b9689e "sched: introduce vlan action" added both the
UAPI values for the vlan actions (TCA_VLAN_ACT_) and these two
in-kernel ones which are not used, remove them.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nf_nat_mangle_{udp,tcp}_packet() returns int. However, it is used as
bool type in many spots. Fix this by consistently handle this return
value as a boolean.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A few more things for 4.12:
- ttm and amdgpu support for non-contiguous vram CPU mappings
- lots of bug fixes and cleanups for vega10
- misc bug fixes and code cleanups
[airlied: fix do_div error on 32-bit arm, not sure it's 100% correct]
* 'drm-next-4.12' of git://people.freedesktop.org/~agd5f/linux: (58 commits)
drm/amdgpu: use uintptr_t instead of unsigned long to store pointer
drm/amdgpu: Avoid using signed integer to store pointer value
drm/amdgpu:invoke new implemented AI MB func
drm/amdgpu/vega10:timeout set to equal with VI
drm/amdgpu:implement the reset MB func for vega10
drm/amdgpu:fix typo for mxgpu_ai
drm/amdgpu:no need to involv HDP in KIQ
drm/amdgpu:add PSP block only load_type=PSP (v2)
drm/amdgpu/smu9: update to latest driver interface
drm/amd/amdgpu: cleanup gfx_v9_0_gpu_init()
drm/amd/amdgpu: cleanup gfx_v9_0_rlc_reset()
drm/amd/amdgpu: cleanup gfx_v9_0_rlc_start()
drm/amd/amdgpu: simplify gfx_v9_0_cp_gfx_enable()
drm/amd/amdgpu: cleanup gfx_v9_0_kiq_init_register()
drm/amd/amdgpu: Drop gfx_v9_0_print_status()
drm/amd/amdgpu: cleanup gfx_v9_0_set_gfx_eop_interrupt_state()
drm/amd/amdgpu: cleanup gfx_v9_0_set_priv_reg_fault_state()
drm/amd/amdgpu: cleanup gfx_v9_0_set_priv_inst_fault_state()
drm/amd/amdgpu: cleanup gfx_v9_0_init_queue()
drm/amdgpu: Move function amdgpu_has_atpx near other similar functions
...
Highlights:
- Cooling device support from Russell, to allow GPU throttling on system
thermal overload.
- Explicit fencing support from Philipp, implemented in a similar way to
drm/msm.
* 'etnaviv/next' of https://git.pengutronix.de/git/lst/linux:
drm/etnaviv: submit support for out-fences
drm/etnaviv: return GPU fence through the submit structure
drm/etnaviv: submit support for in-fences
drm/etnaviv: add etnaviv cooling device
drm/etnaviv: switch to postclose
drm/etnaviv: add lockdep assert to fence allocation
mode_valid() called from drm_helper_probe_single_connector_modes()
may need to look at connector->state because what a valid mode is may
depend on connector properties being set. For example some HDMI modes
might be rejected when a connector property forces the connector
into DVI mode.
Some implementations of detect() already lock all state,
so we have to pass an acquire_ctx to them to prevent a deadlock.
This means changing the function signature of detect() slightly,
and passing the acquire_ctx for locking multiple crtc's.
For the callbacks, it will always be non-zero. To allow callers
not to worry about this, drm_helper_probe_detect_ctx is added
which might handle -EDEADLK for you.
Changes since v1:
- Always set ctx parameter.
Changes since v2:
- Always take connection_mutex when probing.
Changes since v3:
- Remove the ctx from intel_dp_long_pulse, and add
WARN_ON(!connection_mutex) (danvet)
- Update docs to clarify the locking situation. (danvet)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1491504920-4017-1-git-send-email-maarten.lankhorst@linux.intel.com
Add a helper function regulator_set_pull_down_regmap to allow regmap
based regulators to easily enable pull down.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a helper function regulator_set_soft_start_regmap to allow regmap
based regulators to easily enable soft start.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
