The hystart code was written with assumption that HZ=1000.
Replace the use of jiffies with bictcp_clock as a millisecond
real time clock.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reported-by: Lucas Nussbaum <lucas.nussbaum@loria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the spacing between ACK's that indicates a train a tuneable
value like other hystart values.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiffies wraps around therefore the correct way to compare is
to use cast to signed value.
Note: cubic is not using full jiffies value on 64 bit arch
because using full unsigned long makes struct bictcp grow too
large for the available ca_priv area.
Includes correction from Sangtae Ha to improve ack train detection.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the congestion control interface, the callback for each ACK
includes an estimated round trip time in microseconds.
Some algorithms need high resolution (Vegas style) but most only
need jiffie resolution. If RTT is not accurate (like a retransmission)
-1 is used as a flag value.
When doing coarse resolution if RTT is less than a a jiffie
then 0 should be returned rather than no estimate. Otherwise algorithms
that expect good ack's to trigger slow start (like CUBIC Hystart)
will be confused.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch turns on RX checksum and GRO by default. To improve
receiving performance and reduce congestion in case of network
bursts we also increase the default number of inbound buffers.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a6c36ee677 ("bonding: change list
contact to netdev@vger.kernel.org"), the mailing list for bonding
developpement was changed from bonding-devel to netdev.
Update the bonding documentation to reflect this change:
- bonding-devel is used for usage discussions (despite the name).
- netdev is used for developpement discussions.
Also remove the reference to the sourceforge bonding page, which is
deprecated.
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems drivers/firewire/ohci.c is making some optimistic assumptions
about struct fw_ohci and that member "card" will always remain the first
member of the struct.
Plus it's probably going to confuse a lot of static code analyzers too.
So I wonder if there is a good reason not to free the ohci struct just
like it was allocated instead of the tricky &ohci->card way?
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
It is perhaps just a rudiment from before mainline submission of the
driver.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Since commit 82b662dc41 "flush AT contexts after bus reset for OHCI 1.2",
the driver takes care of any AT packets that were enqueued during a bus
reset phase. The check from commit 76f73ca1b2 is therefore no longer
necessary and the MMIO read can be avoided.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Commit 45a52a0207 (NFS move nfs_client
initialization into nfs_get_client) introduces a new warning in
fs/nfs/idmap.c:
‘struct rpc_timeout’ declared inside parameter list
Fix it by adding a forward declaration for the struct rpc_timeout
in include/linux/nfs_xdr.h
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We latch our state using a spinlock not a r/w kind of lock.
Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, for N 5800 XM I get:
cdc_phonet: probe of 1-6:1.10 failed with error -22
It's because phonet_header is empty. Extra altsetting looks like
there:
E 05 24 00 01 10 03 24 ab 05 24 06 0a 0b 04 24 fd .$....$..$....$.
E 00 .
I don't see the header used anywhere so just check if the phonet
descriptor is there, not the structure itself.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is a warning emitted by the cdc-phonet driver:
WARNING: at include/linux/netdevice.h:1557 usbpn_probe+0x3bb/0x3f0 [cdc_phonet]()
Modules linked in: ...
Pid: 5877, comm: insmod Not tainted 2.6.37.3-16-desktop #1
Call Trace:
[<ffffffff810059b9>] dump_trace+0x79/0x340
[<ffffffff81520fdc>] dump_stack+0x69/0x6f
[<ffffffff810580eb>] warn_slowpath_common+0x7b/0xc0
[<ffffffffa00254fb>] usbpn_probe+0x3bb/0x3f0 [cdc_phonet]
...
---[ end trace f5d3e02908603ab4 ]---
netif_stop_queue() cannot be called before register_netdev()
So remove netif_stop_queue from the probe funtction to avoid that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-mn10300:
MN10300: atomic_read() should ensure it emits a load
MN10300: The SMP_ICACHE_INV_FLUSH_RANGE IPI command does not exist
MN10300: Proper use of macros get_user() in the case of incremented pointers
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (26 commits)
MIPS: Alchemy: Fix reset for MTX-1 and XXS1500
MIPS: MTX-1: Make au1000_eth probe all PHY addresses
MIPS: Jz4740: Add HAVE_CLK
MIPS: Move idle task creation to work queue
MIPS, Perf-events: Use unsigned delta for right shift in event update
MIPS, Perf-events: Work with the new callchain interface
MIPS, Perf-events: Fix event check in validate_event()
MIPS, Perf-events: Work with the new PMU interface
MIPS, Perf-events: Work with irq_work
MIPS: Fix always CONFIG_LOONGSON_UART_BASE=y
MIPS: Loongson: Fix potentially wrong string handling
MIPS: Fix GCC-4.6 'set but not used' warning in arch/mips/mm/init.c
MIPS: Fix GCC-4.6 'set but not used' warning in ieee754int.h
MIPS: Remove unused code from arch/mips/kernel/syscall.c
MIPS: Fix GCC-4.6 'set but not used' warning in signal*.c
MIPS: MSP: Fix MSP71xx bpci interrupt handler return value
MIPS: Select R4K timer lib for all MSP platforms
MIPS: Loongson: Remove ad-hoc cmdline default
MIPS: Clear the correct flag in sysmips(MIPS_FIXADE, ...).
MIPS: Add an unreachable return statement to satisfy buggy GCCs.
...
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: ce4100: Set pci ops via callback instead of module init
x86/mm: Fix pgd_lock deadlock
x86/mm: Handle mm_fault_error() in kernel space
x86: Don't check for BIOS corruption in first 64K when there's no need to
So far be2net has been using BE3 in legacy mode. It now checks for native
mode capability and if available it sets it. In native mode, the RX_COMPL
structure is different from that in legacy mode.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts the parent commit. I hate doing that, but it's generating
some discussion ("half of it is right"), and since I am planning on
doing the 2.6.38 release later today we can punt it to stable if
required. Let's not rock the boat right now.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Notify firmware when a Flex-10 interface is brought down
so that virtual connect manager can display the correct link status.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If Spanning Tree Protocol is not enabled, there is no good reason for
the bridge code to wait for the forwarding delay period before enabling
the link. The purpose of the forwarding delay is to allow STP to
learn about other bridges before nominating itself.
The only possible impact is that when starting up a new port
the bridge may flood a packet now, where previously it might have
seen traffic from the other host and preseeded the forwarding table.
Includes change for local variable br already available in that func.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't reset tx_fifo_errors when reading out current EMAC stats.
(tx_fifo_errors shows up as TX overruns in netdev stats.)
Without this correction, the old counter value is lost every time
stats are read out.
Signed-off-by: Thomas Lange <thomas@corelatus.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylib would silently ignore the phy_id argument to these ioctls and
perform the read/write with the active phydev address, whereas most
non-phylib drivers seem to allow access to all mdio addresses
(E.G. pcnet_cs).
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update 5709 mips firmware to 6.2.1a to fix iSCSI performance
regression. There was an unnecessary context read in the fast path
affecting performance.
Update bnx2 to 2.1.6.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides support to the newer version of firmware devcmd CMD_MCPU_FW_INFO
that returns additional information (ASIC type and revision) about the underlying hardware.
This knowledge is required by the driver to implement any hardware specific features.
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the bridge device behave like a physical device.
In earlier releases the bridge always asserted carrier. This
changes the behavior so that bridge device carrier is on only
if one or more ports are in the forwarding state. This
should help IPv6 autoconfiguration, DHCP, and routing daemons.
I did brief testing with Network and Virt manager and they
seem fine, but since this changes behavior of bridge, it should
wait until net-next (2.6.39).
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Tested-By: Adam Majer <adamm@zombino.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a couple of build warnings when CONFIG_PM is enabled but
CONFIG_PM_SLEEP is disabled. Applies on top of v2.6.38-rc7 - I know it's
late, but it would be great if v2.6.38 could compile without warnings!
Signed-off-by: Michel Lespinasse <walken@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SH7757's ETHER and GETHER use common MDIO pin. The MDIO pin is
selected by specific register. So this patch adds new interface in
bb_info, and when the sh_eth driver use the mdio, the register can
be changed by the function.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous code had hardcoded the PHY_INTERFACE_MODE_MII of phy_connect.
So some Gigabit PHYs will not behave correctly.
The patch adds the phy_interface in sh_eth_plat_data, so we can select
the phy interface.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SH7763 has GETHER. So the specification of some registers differs than
other CPUs. This patch removes almost #ifdef of CONFIG_CPU_SUBTYPE_SH7763.
Then we are able to add other CPU's GETHER easily.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The defination is hardcoded in this driver for some CPUs. This patch
modifies to get resource of TSU address from platform_device.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous code cannot handle the ETHER and GETHER both as same time
because the definitions of register was hardcoded.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(bug introduced by commit 26ad787962
(pktgen: speedup fragmented skbs)
The headers of pktgen were incorrectly added in a pktgen packet
without frags (frags=0). There was an offset in the pktgen headers.
The cause was in reusing the pgh variable as a return variable in skb_put
when adding the payload to the skb.
Signed-off-by: Daniel Turull <daniel.turull@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
oom_kill_process() starts with victim_points == 0. This means that
(most likely) any child has more points and can be killed erroneously.
Also, "children has a different mm" doesn't match the reality, we should
check child->mm != t->mm. This check is not exactly correct if t->mm ==
NULL but this doesn't really matter, oom_kill_task() will kill them
anyway.
Note: "Kill all processes sharing p->mm" in oom_kill_task() is wrong
too.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 522d7dec(futex: Remove redundant pagefault_disable in
futex_atomic_cmpxchg_inatomic()) added a bogus comment.
/* Note that preemption is disabled by futex_atomic_cmpxchg_inatomic
* call sites. */
Bogus in two aspects:
1) pagefault_disable != preempt_disable even if the mechanism we use
is the same
2) we have a call site which deliberately does not disable pagefaults
as it wants the possible fault to be handled - though that has been
changed for consistency reasons now.
Sigh. I really should have seen that when committing the above. :(
Catched-by-and-rightfully-ranted-at-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <alpine.LFD.2.00.1103141126590.2787@localhost6.localdomain6>
Cc: Michel Lespinasse <walken@google.com>
Cc: Darren Hart <darren@dvhart.com>
Since commit 32fd6901 (MIPS: Alchemy: get rid of common/reset.c)
Alchemy-based boards use their own reset function. For MTX-1 and XXS1500,
the reset function pokes at the BCSR.SYSTEM_RESET register, but this does
not work. According to Bruno Randolf, this was not tested when written.
Previously, the generic au1000_restart() routine called the board specific
reset function, which for MTX-1 and XXS1500 did not work, but finally made
a jump to the reset vector, which really triggers a system restart. Fix
reboot for both targets by jumping to the reset vector.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2093/
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When au1000_eth probes the MII bus for PHY address, if we do not set
au1000_eth platform data's phy_search_highest_address, the MII probing
logic will exit early and will assume a valid PHY is found at address 0.
For MTX-1, the PHY is at address 31, and without this patch, the link
detection/speed/duplex would not work correctly.
CC: stable@kernel.org
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2111/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To avoid forking usermode thread when creating an idle task, move fork_idle
to a work queue.
If kernel starts with maxcpus= option which does not bring all available
cpus online at boot time, idle tasks for offline cpus are not created. If
later offline cpus are hotplugged through sysfs, __cpu_up is called in
the context of the user task, and fork_idle copies its non-zero mm
pointer. This causes BUG() in per_cpu_trap_init.
This also avoids issues with resource limits of the CPU writing to sysfs,
containers, maybe others.
Signed-off-by: Maksim Rayskiy <mrayskiy@broadcom.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2070/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the MIPS part of the following commits by Frederic Weisbecker:
- f72c1a931e
perf: Factorize callchain context handling
Store the kernel and user contexts from the generic layer instead
of archs, this gathers some repetitive code.
- 56962b4449
perf: Generalize some arch callchain code
- Most archs use one callchain buffer per cpu, except x86 that needs
to deal with NMIs. Provide a default perf_callchain_buffer()
implementation that x86 overrides.
- Centralize all the kernel/user regs handling and invoke new arch
handlers from there: perf_callchain_user() / perf_callchain_kernel()
That avoid all the user_mode(), current->mm checks and so...
- Invert some parameters in perf_callchain_*() helpers: entry to the
left, regs to the right, following the traditional (dst, src).
- 70791ce9ba
perf: Generalize callchain_store()
callchain_store() is the same on every archs, inline it in
perf_event.h and rename it to perf_callchain_store() to avoid
any collision.
This removes repetitive code.
- c1a65932fd
perf: Drop unappropriate tests on arch callchains
Drop the TASK_RUNNING test on user tasks for callchains as
this check doesn't seem to make any sense.
Also remove the tests for !current that is not supposed to
happen and current->pid as this should be handled at the
generic level, with exclude_idle attribute.
Reported-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: a.p.zijlstra@chello.nl
To: will.deacon@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: dengcheng.zhu@gmail.com
Cc: matt@console-pimps.org
Cc: sshtylyov@mvista.com
Patchwork: http://patchwork.linux-mips.org/patch/2014/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
