Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for DISPC is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.
DISPC platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for RFBI is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.
RFBI platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
All clock management is moved to dss platform driver. clk_get/put APIs use
dss device instead of core platform device.
Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So the device name is changed from omapdss to omapdss_dss in 2420, 2430,
3xxx clock database files. Now the core driver "omapdss" only takes care
of panel registration with the custom bus.
core driver also uses the clk_enable() / clk_disable() APIs exposed by DSS for
clock management.
DSS driver would do clock management of clocks needed by DISPC, RFBI, DSI, VENC
TODO: The clock content would be adapted to omap_hwmod in a seperate series.
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver of DSS is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.
DSS platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Looks up the hwmod database for each of the given DSS HW IP and builds
omap_device which inturn does the platform device register for each of DSS HW IP
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As part of omap hwmod changes, DSS will not be the only controller of its
clocks. hwmod initialization also enables the interface clocks, and
manages them.
So, when DSS is built as a module, omap_dss_remove doesn't try to disable
all clocks that have a higher usecount.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
ASoC audio for mini2440 platform in current kenrel doesn't work.
First problem is samsung_asoc_dma device is missing in initialization.
Next problem is with codec. Codec is initialized but never probed
because no platform_device exist for codec driver. It leads to errors
during codec binding to asoc dai. Next problem was platform data which
was passed from board to asoc main driver but not passed to codec when
called codec_soc_probe().
Following patch should fix issues. But not sure if in correct way.
Please review.
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
As inval_cache_and_wait_for_operation() drop and reclaim the lock
to invalidate the cache, some other thread may suspend the operation
before reaching the for(;;) loop. Therefore the loop must start with
checking the chip->state before reading status from the chip.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Michael Cashwell <mboards@prograde.net>
Acked-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
In the commit 08968041be
(mtd: cfi_cmdset_0002: make sector erase command variable)
introdused a field sector_erase_cmd. In the same commit initialisation
of cfi->sector_erase_cmd made in cfi_chip_setup()
(file drivers/mtd/chips/cfi_probe.c), so the CFI chip has no problem:
...
cfi->cfi_mode = CFI_MODE_CFI;
cfi->sector_erase_cmd = CMD(0x30);
...
But for the JEDEC chips this initialisation is not carried out,
so the JEDEC chips have sector_erase_cmd == 0.
This patch adds the missing initialisation.
Signed-off-by: Antony Pavlov <antony@niisi.msk.ru>
Acked-by: Guillaume LECERF <glecerf@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
CC: stable@kernel.org
In the following commit, we'll need to use the CMD() macro in order to
fix the initialisation of the sector_erase_cmd field. That requires the
local variable to be called 'cfi', so change it first in a simple patch.
Signed-off-by: Antony Pavlov <antony@niisi.msk.ru>
Acked-by: Guillaume LECERF <glecerf@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
CC: stable@kernel.org
This patch adds ASoC support for the MAX9850 codec with headphone
amplifier.
Supported features:
- Playback
- 16, 20 and 24 bit audio
- 8k - 48k sample rates
- DAPM
Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The log lock is currently used to protect the AIL lists and
the movements of buffers into and out of them. The lists
are self contained and no log specific items outside the
lists are accessed when starting or emptying the AIL lists.
Hence the operation of the AIL does not require the protection
of the log lock so split them out into a new AIL specific lock
to reduce the amount of traffic on the log lock. This will
also reduce the amount of serialisation that occurs when
the gfs2_logd pushes on the AIL to move it forward.
This reduces the impact of log pushing on sequential write
throughput.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The result is not going to change under us, so no need to reevaluate
this over and over. Seems to be a leftover from the mechanical mass
conversion of task->pid to task_pid_vnr(tsk).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Added a new API function snd_ctl_activate_id() for activate / inactivate
the control element dynamically.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The driver doesn't support Wake-on-ARP, so don't advertise through ethtool
that it does.
Cleanup some coding style issues in the same functions.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If/when an OEM enables MACsec in the 82579 EEPROM, disable jumbo frames
support in the driver due to an interoperability issue in hardware that
prevents jumbo packets from being transmitted or received.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When PHY reset is intentionally blocked on 82577/8/9, do not toggle the
LANPHYPC value bit (essentially performing a hard power reset of the
device) otherwise the PHY can be put into an unknown state.
Cleanup whitespace in the same function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The link can be unexpectedly dropped when the timer for entering EEE low-
power-idle quiet state expires too soon. The timer needs to be extended
from 196usec to 200usec after every LCD (PHY) reset to prevent this from
happening.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With some PHYs supported by this driver, link establishment can take a
little longer when connected to certain switches. Extend the timeout to
reduce the number of false diagnostic failures, and cleanup a code style
issue in the same function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on a report and patch originally submitted by Prasanna Panchamukhi.
Use dev_kfree_skb_irq() in e1000_clean_jumbo_rx_irq() since this latter
function is called only in interrupt context. This avoids "Warning:
kfree_skb on hard IRQ" messages.
Cc: "Prasanna S. Panchamukhi" <prasanna.panchamukhi@riverbed.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removed Tx hang detection mechanism from ixgbevf.
This mechanism has no affect and can cause false alarm messages in some
cases. Especially when VF Tx rate limit is turned on.
The same mechanism was removed recently from igbvf.
Signed-off-by: Lior Levy <lior.levy@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
GFS2 fallocate wasn't properly checking if a blocks were already allocated.
In write_empty_blocks(), if a page didn't have buffer_heads attached, GFS2
was always treating it as if there were no blocks allocated for that page.
GFS2 now calls gfs2_block_map() to check if the blocks are allocated before
writing them out.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This is a small patch that optimizes multiple glock dequeue
operations. It changes the unlock order to be more efficient
and makes it easier for lock debugging tools to unravel. It
also eliminates the need for the temp variable x, although
that would likely be optimized out.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Add proper documentation for previously added net_device_ops ops for FCoE.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are two dividers used to derive bus clock from system clock:
system clock is divided by SCKDIV+1, then by BCKDIV+1. SCKDIV divider
has been ignored up to now, which is no problem as long as it is 0.
Take SCKDIV into account for bus clock calculation.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove double definition of ACLKUSBH, change parameter name in
root_clk_disable, as there is no reason to have a different name than
in root_clk_enable.
No functional change.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is no reason why in case of PLL2 the configuration register
should be read twice, while for PLL0/1 using the value previously read
is used. Do the same for PLL2.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The calculation of the best divider value for a requested clock rate
always returned a value that was slightly too large. It was also not
protected against possible divisions by zero.
Request for very low, but non zero rates would cause the ACLK divisor
field to overflow. Catch this situation by using the maximum value.
The internal function aclk_set_rate() calculates the correct divider
value, but doesn't write it back to the register. Add the write back.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The evaluation board is driven with 1.2V core voltage, so system clock
must not exceed 192 MHz, bus clock must not exceed 110 MHz. Choose
appropriate values and set DTCMWAIT accordingly. Adapt UART setting to
avoid console log interruption and wait for the specified locking time
of 300us to pass.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If NAND is enabled we better have the include around.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change the default UBIFS behavior WRT data CRC checking. Currently,
UBIFS checks data CRC when reading, which slows it down quite a bit,
and this is the default option. However, it looks like in average
user does not need this feature and would prefer faster read speed
over extra reliability. And this seems to be de-facto standard that
file-systems do not check data CRC every time they read from the
media.
Thus, make UBIFS default behavior so that it does not check data
CRC. This corresponds to the no_chk_data_crc mount option. Those users
who need extra protection can always enable it using the chk_data_crc
option.
Please, read more information about this feature here:
http://www.linux-mtd.infradead.org/doc/ubifs.html#L_checksumming
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Remove debug message level and debug checks Kconfig options as they
proved to be useless anyway. We have sysfs interface which we can
use for fine-grained debugging messages and checks selection, see
Documentation/filesystems/ubifs.txt for mode details.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Running kernel 2.6.37, my PPC-based device occasionally gets an
order-2 allocation failure in UBIFS, which causes the root FS to
become unwritable:
kswapd0: page allocation failure. order:2, mode:0x4050
Call Trace:
[c787dc30] [c00085b8] show_stack+0x7c/0x194 (unreliable)
[c787dc70] [c0061aec] __alloc_pages_nodemask+0x4f0/0x57c
[c787dd00] [c0061b98] __get_free_pages+0x20/0x50
[c787dd10] [c00e4f88] ubifs_jnl_write_data+0x54/0x200
[c787dd50] [c00e82d4] do_writepage+0x94/0x198
[c787dd90] [c00675e4] shrink_page_list+0x40c/0x77c
[c787de40] [c0067de0] shrink_inactive_list+0x1e0/0x370
[c787de90] [c0068224] shrink_zone+0x2b4/0x2b8
[c787df00] [c0068854] kswapd+0x408/0x5d4
[c787dfb0] [c0037bcc] kthread+0x80/0x84
[c787dff0] [c000ef44] kernel_thread+0x4c/0x68
Similar problems were encountered last April by Tomasz Stanislawski:
http://patchwork.ozlabs.org/patch/50965/
This patch implements Artem's suggested fix: fall back to a
mutex-protected static buffer, allocated at mount time. I tested it
by forcing execution down the failure path, and didn't see any ill
effects.
Artem: massaged the patch a little, improved it so that we'd not
allocate the write reserve buffer when we are in R/O mode.
Signed-off-by: Matthew L. Creech <mlcreech@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Add common code for MIPI-CSIS and MIPI-DSIM drivers to support
their corresponding D-PHY's enable and reset control.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Extend MIPI-CSIS driver's platform data structure with a callback
for D-PHY enable and reset control. Also add a flag indicating
whether the external MIPI-CSI (VDD18_MIPI) power supply should
be managed in the driver through the "vdd" power supply. On some
boards this regulator may be a fixed voltage regulator without
an inhibit function.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
