This avoids the S305 panic during incoming connection.
S305 sends PSM 25 L2CAP connection request before the L2CAP info response.
When we receive that info response we crash on null pointer here.
Bug: 2127637
Change-Id: Ib637516251f46fa9a9c87ac015dc2f27df5a27fd
Signed-off-by: Nick Pelly <npelly@google.com>
With Bluetooth 2.1 ACL packets can be flushable or non-flushable. This commit
makes ACL data packets non-flushable by default on compatible chipsets, and
adds the L2CAP_LM_FLUSHABLE socket option to explicitly request flushable ACL
data packets for a given L2CAP socket. This is useful for A2DP data which can
be safely discarded if it can not be delivered within a short time (while
other ACL data should not be discarded).
Note that making ACL data flushable has no effect unless the automatic flush
timeout for that ACL link is changed from its default of 0 (infinite).
Change-Id: Ie3d4befdeaefb8c979de7ae603ff5ec462b3483c
Signed-off-by: Nick Pelly <npelly@google.com>
__u16 sco_pkt_type is introduced to struct sockaddr_sco. It allows bitwise
selection of SCO/eSCO packet types. Currently those bits are:
0x0001 HV1 may be used.
0x0002 HV2 may be used.
0x0004 HV3 may be used.
0x0008 EV3 may be used.
0x0010 EV4 may be used.
0x0020 EV5 may be used.
0x0040 2-EV3 may be used.
0x0080 3-EV3 may be used.
0x0100 2-EV5 may be used.
0x0200 3-EV5 may be used.
This is similar to the Packet Type parameter in the HCI Setup Synchronous
Connection Command, except that we are not reversing the logic on the EDR bits.
This makes the use of sco_pkt_tpye forward portable for the use case of
white-listing packet types, which we expect will be the primary use case.
If sco_pkt_type is zero, or userspace uses the old struct sockaddr_sco,
then the default behavior is to allow all packet types.
Packet type selection is just a request made to the Bluetooth chipset, and
it is up to the link manager on the chipset to negiotiate and decide on the
actual packet types used. Furthermore, when a SCO/eSCO connection is eventually
made there is no way for the host stack to determine which packet type was used
(however it is possible to get the link type of SCO or eSCO).
sco_pkt_type is ignored for incoming SCO connections. It is possible
to add this in the future as a parameter to the Accept Synchronous Connection
Command, however its a little trickier because the kernel does not
currently preserve sockaddr_sco data between userspace calls to accept().
The most common use for sco_pkt_type will be to white-list only SCO packets,
which can be done with the hci.h constant SCO_ESCO_MASK.
This patch is motivated by broken Bluetooth carkits such as the Motorolo
HF850 (it claims to support eSCO, but will actually reject eSCO connections
after 5 seconds) and the 2007/2008 Infiniti G35/37 (fails to route audio
if a 2-EV5 packet type is negiotiated). With this patch userspace can maintain
a list of compatible packet types to workaround remote devices such as these.
Based on a patch by Marcel Holtmann.
Change-Id: I304d8fda5b4145254820a3003820163bf53de5a5
Signed-off-by: Nick Pelly <npelly@google.com>
power_save is a feature to allow HID devices to control the sniff mode.
Unfortunately it also prevents us exiting sniff mode on some A2DP devices
that do not explicitly exit sniff mode themselves, resulting in skipping
audio.
Marcel is trying to finalize a setsockopt() API to control whether power_save
is enabled on a per socket basis. In the mean-time, turn off power_save for
Android, since we do not have official HID support, and this is causing
problems for A2DP which we do support.
(Note the power_save logic is reversed, 0 is on, 1 is off).
Change-Id: Ife4478055128b81669bf49308d2e2199e1aa11a1
Signed-off-by: Nick Pelly <npelly@google.com>
With Bluetooth 2.1 ACL packets can be flushable or non-flushable. This changes
makes the default ACL packet non-flushable, and allows selection of flushable
packets on a per-L2CAP socket basis with L2CAP_LM_FLUSHABLE.
Note the HCI Write Automatic Flush Timeout command also needs to be issued
to set the flush timeout to non-zero.
Need to featurize this change to Bluetooth 2.1 chipsets only before pushing
upstream.
Signed-off-by: Nick Pelly <npelly@google.com>
This is to support the Motorola HF850 carkit which reports the error code 0x10
for an eSCO attempt, even though it advertises eSCO support. Here is the
hcidump:
2009-09-22 15:40:24.492391 < HCI Command: Setup Synchronous Connection
(0x01|0x0028) plen 17
handle 1 voice setting 0x0060
2009-09-22 15:40:24.493002 > HCI Event: Command Status (0x0f) plen 4
Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
2009-09-22 15:40:30.594869 > HCI Event: Synchronous Connect Complete (0x2c)
plen 17
status 0x10 handle 257 bdaddr 00:50:CD:20:C6:84 type eSCO
Error: Connection Accept Timeout Exceeded
With this patch we will retry with a SCO connection, which succeeds.
Unfortunately the Moto HF850 also takes 5 seconds to return the error for the
eSCO attempt, so it will still take 5 seconds to fallback to SCO with this
patch.
Signed-off-by: Nick Pelly <npelly@google.com>
This fixes a bug where shutdown() and close() on a rfcomm socket during ACL
connection would not cause HCI Create Connection Cancel.
Signed-off-by: Nick Pelly <npelly@google.com>
With CONFIG_ANDROID_PARANOID_NETWORK, require specific uids/gids to instantiate
network sockets.
Signed-off-by: Robert Love <rlove@google.com>
paranoid networking: Use in_egroup_p() to check group membership
The previous group_search() caused trouble for partners with module builds.
in_egroup_p() is also cleaner.
Signed-off-by: Nick Pelly <npelly@google.com>
Fix 2.6.29 build.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
net: Fix compilation of the IPv6 module
Fix compilation of the IPv6 module -- current->euid does not exist anymore,
current_euid() is what needs to be used.
Signed-off-by: Steinar H. Gunderson <sesse@google.com>
remote_tx_win is intended to be set on receipt of an L2CAP
configuration request. The value is used to determine the size of the
transmit window on the remote side of an ERTM connection, so L2CAP
can stop sending frames when that remote window is full.
An incorrect remote_tx_win value will cause the stack to not fully
utilize the tx window (performance impact), or to overfill the remote
tx window (causing dropped frames or a disconnect).
This patch removes an extra setting of remote_tx_win when a
configuration response is received. The transmit window has a
different meaning in a response - it is an informational value
less than or equal to the local tx_win.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Incoming configuration values must be converted to native CPU order
before use. This fixes a bug where a little-endian MPS value is
compared to a native CPU value. On big-endian processors, this
can cause ERTM and streaming mode segmentation to produce PDUs
that are larger than the remote stack is expecting, or that would
produce fragmented skbs that the current FCS code cannot handle.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Check result code of L2CAP information response. Otherwise
it would read invalid feature mask and access invalid memory.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the remote side doesn't support Enhanced Retransmission Mode neither
Streaming Mode, we shall not send the RFC option.
Some devices that only supports Basic Mode do not understanding the RFC
option. This patch fixes the regression found with these devices.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Those annotation save memory and space on the binary. __init code is
discarded just after execute and __exit code is discarded if the module
is built into the kernel image or unload of modules is not allowed.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Testing first we avoid enter the loop when count = 0.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Change the enable_ertm param to disable_ertm and default value to 0. That
means that L2CAP Extended features are enabled by default now.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Modified packet based reassembly function hci_recv_fragment() to use
hci_reassembly()
Signed-off-by: Suraj Sumangala <suraj@atheros.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implements feature to reassemble received HCI frames from any input stream
Signed-off-by: Suraj Sumangala <suraj@atheros.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We did some changes on the L2CAP configuration process and its behaviour
is bit different now. That justifies a updated on the L2CAP version.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Copyright for the time I worked on L2CAP during the Google Summer of Code
program.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Purely a cosmetic change, it doesn't change the code flow.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Probably a typo error. We were using the wrong struct to get size.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The extended L2CAP features requires that one should initiate a
ConfigReq after send the ConnectionRsp. This patch changes the behaviour
of the configuration process of our stack.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we try to send a message bigger than the outgoing MTU value
EMSGSIZE (message too long) should be returned.
Signed-off-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now we also check if can push skb userspace just after receive a new
skb instead of only wait the l2cap_busy_work wake up from time to time
to check the local busy condition.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
backlog queue is the canonical mechanism to avoid race conditions due
interrupts in bottom half context. After the socket lock is released the
net core take care of push all skb in its backlog queue.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Using a lock to deal with the ERTM race condition - interruption with
new data from the hci layer - is wrong. We should use the native skb
backlog queue.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If such event happens we shall reply with a Command Reject, because we are
not expecting any configure request.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When mode is mandatory we shall not send connect request and report this
to the userspace as well.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since now we have checks for the supported mode before on
l2cap_info_rsp we can remove the check for it here.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If our mode is Basic Mode we have to refuse any ConfigRsp that proposes
a different mode.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Profile Tuning Suite requires that we send a RFC containing the
Basic Mode configuration when requesting Basic Mode.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we choose to use Basic Mode then we have to refuse the received mode
and propose Basic Mode again.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
