Huazhong Tan says:
====================
hns3: provide new interfaces & bugfixes & code optimization
This patchset provides some reset interfaces for RAS & RoCE, also
some bugfixes and optimization related to reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not necessary to reallocate the descriptor and remap the
descriptor memory in reset process, otherwise it may cause memory
not freed problem.
Also, this patch initializes the cmd queue's spinlocks in
hclgevf_alloc_cmd_queue, and take the spinlocks when reinitializing
cmd queue' registers.
Fixes: fedd0c15d2 ("net: hns3: Add HNS3 VF IMP(Integrated Management Proc) cmd interface")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hclge_reset() is called, it may fail for several reasons.
For example, an higher-level reset event occurs, memory allocation
failure, hardware reset timeout, etc. Therefore, it is necessary
to add corresponding error handling for these situations.
1. A high-level reset is required due to a high-level reset failure.
2. For memory allocation failure, a high-level reset is initiated by
the timer to recover. The reason for using the timer is to prevent this
new high-level reset to interrupt the reset process of other pf/vf;
3. For the case of hardware reset timeout, reschedule the reset task
to wait for the hardware to complete the reset.
For memory allocation failure and reset timeouts, in order to prevent
an infinite number of scheduled reset tasks, the number of error
recovery needs to be limited.
This patch also add some reset related debug log printing.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing resetting, roce should do its uninitailization part
before nic's, and do its initialization part after nic's.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing PF reset, the driver needs to do some preparatory work
before asserting PF reset. Since when hardware is resetting, it
is necessary to stop tx/rx queue, clear hardware table, etc,
otherwise hardware may run into unrecoverable state if there is
still IO running when the hardware is resetting.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saving reset related information in the hclge_dev/hclgevf_dev
structure is more suitable than the hnae3_handle, since hardware
related information is kept in these two structure.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing a higher level reset, the pending lower level reset
does not have to be processed anymore, because the higher level
reset is the superset of the lower level reset.
Therefore, when processing an higher level reset, the request of
lower level reset needs to be cleared.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While hclge is going to reset, it will notify its client with
HNAE3_DOWN_CLIENT, so this client should get into a resetting
status from this moment, other operations from the stack need to
be blocked as well. And when the reset is finished, the client
will be notified with HNAE3_UP_CLIENT, so this is the end of
the resetting status.
This patch uses HNS3_NIC_STATE_RESETTING flag to implement that,
and adds hns3_nic_resetting() to indicate which operation is not
allowed.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While hardware gets into reset status, the firmware will not respond to
driver's command request, which may cause ring not disabled problem
during reset process.
So this patch uses register instead of command to enable/disable the ring
in the enet while doing UP/DOWN operation.
Also, HNS3_RING_RX_VM_REG is previously unused, so change it to the
correct meaning, and add a wrapper function for readl().
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing a function reset, the hardware table should be cleared
before the hardware reset. In current code, this clearing is done
in hns3_reset_notify_uninit_enet, but it is too late, because
the hardware reset is already done, hns3_reset_notify_down_enet
is more suitable to do that.
Fixes: bb6b94a896 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The client needs to know if the hardware is resetting when
loading or unloading itself, because client may abort the loading
process or wait for the reset process to finish when unloading
if hardware is resetting.
So this patch provides these interfaces to do it.
1. get_hw_reset_stat, the reset status of hardware.
2. ae_dev_resetting, whether reset task is scheduling.
3. ae_dev_reset_cnt, how many reset has been done.
Also, the RoCE client needs some field in the hnae3_roce_private_info
to save its state, and process_hw_error interface in the
hnae3_client_ops to process hardware errors.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when reset_event is called because of tx timeout, it will
upgrade the reset level (For PF, HNAE3_FUNC_RESET -> HNAE3_CORE_RESET
-> HNAE3_GLOBAL_RESET) if the time between the new reset and last reset
is within 20 secs, or restore the reset level to HNAE3_FUNC_RESET if
the time between the new reset and last reset is over 20 secs.
There is requirement that the caller needs to decide the reset level
when triggering a reset, for example, RAS recovery. So this patch
adds the set_default_reset_request to meet this requirement.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Besides of module_init and module_exit, the process of reset will
also uninitialize and initialize the enet client. When reset process
fails with enet client uninitialized, the module_exit does not need
to uninitialize the enet client, otherwise it may cause double
uninitialization problem.
So we need the HNS3_NIC_STATE_INITED flag to indicate whether
the enet client is initialized.
Also HNS3_NIC_STATE_REINITING is previously unused, so change it to
HNS3_NIC_STATE_INITED.
Fixes: bb6b94a896 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a race between close_ctree() and cleaner_kthread().
close_ctree() sets btrfs_fs_closing(), and the cleaner stops when it
sees it set, but this is racy; the cleaner might have already checked
the bit and could be cleaning stuff. In particular, if it deletes unused
block groups, it will create delayed iputs for the free space cache
inodes. As of "btrfs: don't run delayed_iputs in commit", we're no
longer running delayed iputs after a commit. Therefore, if the cleaner
creates more delayed iputs after delayed iputs are run in
btrfs_commit_super(), we will leak inodes on unmount and get a busy
inode crash from the VFS.
Fix it by parking the cleaner before we actually close anything. Then,
any remaining delayed iputs will always be handled in
btrfs_commit_super(). This also ensures that the commit in close_ctree()
is really the last commit, so we can get rid of the commit in
cleaner_kthread().
The fstest/generic/475 followed by 476 can trigger a crash that
manifests as a slab corruption caused by accessing the freed kthread
structure by a wake up function. Sample trace:
[ 5657.077612] BUG: unable to handle kernel NULL pointer dereference at 00000000000000cc
[ 5657.079432] PGD 1c57a067 P4D 1c57a067 PUD da10067 PMD 0
[ 5657.080661] Oops: 0000 [#1] PREEMPT SMP
[ 5657.081592] CPU: 1 PID: 5157 Comm: fsstress Tainted: G W 4.19.0-rc8-default+ #323
[ 5657.083703] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.2-0-gf9626cc-prebuilt.qemu-project.org 04/01/2014
[ 5657.086577] RIP: 0010:shrink_page_list+0x2f9/0xe90
[ 5657.091937] RSP: 0018:ffffb5c745c8f728 EFLAGS: 00010287
[ 5657.092953] RAX: 0000000000000074 RBX: ffffb5c745c8f830 RCX: 0000000000000000
[ 5657.094590] RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffff9a8747fdf3d0
[ 5657.095987] RBP: ffffb5c745c8f9e0 R08: 0000000000000000 R09: 0000000000000000
[ 5657.097159] R10: ffff9a8747fdf5e8 R11: 0000000000000000 R12: ffffb5c745c8f788
[ 5657.098513] R13: ffff9a877f6ff2c0 R14: ffff9a877f6ff2c8 R15: dead000000000200
[ 5657.099689] FS: 00007f948d853b80(0000) GS:ffff9a877d600000(0000) knlGS:0000000000000000
[ 5657.101032] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 5657.101953] CR2: 00000000000000cc CR3: 00000000684bd000 CR4: 00000000000006e0
[ 5657.103159] Call Trace:
[ 5657.103776] shrink_inactive_list+0x194/0x410
[ 5657.104671] shrink_node_memcg.constprop.84+0x39a/0x6a0
[ 5657.105750] shrink_node+0x62/0x1c0
[ 5657.106529] try_to_free_pages+0x1a4/0x500
[ 5657.107408] __alloc_pages_slowpath+0x2c9/0xb20
[ 5657.108418] __alloc_pages_nodemask+0x268/0x2b0
[ 5657.109348] kmalloc_large_node+0x37/0x90
[ 5657.110205] __kmalloc_node+0x236/0x310
[ 5657.111014] kvmalloc_node+0x3e/0x70
Fixes: 30928e9baa ("btrfs: don't run delayed_iputs in commit")
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add trace ]
Signed-off-by: David Sterba <dsterba@suse.com>
The assignment of the feature flag NETIF_F_NTUPLE and NETIF_F_HW_TC
occurs prior to the initial setup of the local hw_features variable.
This means the features are set as user-changeable, but are not set in
the currently active feature list. This results in the features being
disabled at the driver's initial load.
Move the assignment after the initial assignment of hw_features, and
assign to the local variable. This ensures that NETIF_F_NTUPLE and
NETIF_F_HW_TC are marked as user-changeable, and also enables them by
default when the driver loads.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It seems with some NICs supported by the e1000e driver a SYSTIM reading
may occasionally be few microseconds before the previous reading and if
enabled also pass e1000e_sanitize_systim() without reaching the maximum
number of rereads, even if the function is modified to check three
consecutive readings (i.e. it doesn't look like a double read error).
This causes an underflow in the timecounter and the PHC time jumps hours
ahead.
This was observed on 82574, I217 and I219. The fastest way to reproduce
it is to run a program that continuously calls the PTP_SYS_OFFSET ioctl
on the PHC.
Modify e1000e_phc_gettime() to use timecounter_cyc2time() instead of
timecounter_read() in order to allow non-monotonic SYSTIM readings and
prevent the PHC from jumping.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The call to netif_set_real_num_tx_queues is not assigning the error
return to variable err even though the next line checks err for an
error. Fix this by adding the missing err assignment.
Detected by CoverityScan, CID#1474551 ("Logically dead code")
Fixes: 3df25e4c1e ("igc: Add interrupt support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/intel/igc/igc_main.c: In function 'igc_probe':
drivers/net/ethernet/intel/igc/igc_main.c:3535:11: warning:
variable 'pci_using_dac' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit
d89f88419f ("igc: Add skeletal frame for Intel(R) 2.5G Ethernet Controller support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/intel/igc/igc_base.c: In function 'igc_init_phy_params_base':
drivers/net/ethernet/intel/igc/igc_base.c:240:6: warning:
variable 'ctrl_ext' set but not used [-Wunused-but-set-variable]
u32 ctrl_ext;
drivers/net/ethernet/intel/igc/igc_base.c: In function 'igc_get_invariants_base':
drivers/net/ethernet/intel/igc/igc_base.c:290:6: warning:
variable 'link_mode' set but not used [-Wunused-but-set-variable]
u32 link_mode = 0;
It never used since introduction in
commit c0071c7aa5 ("igc: Add HW initialization code")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's a new flag for setting WoL filters that is only
enabled on one manufacturer's NICs, and it's not ours. Fail
with EOPNOTSUPP.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many of the Intel Ethernet drivers call skb_tx_timestamp() earlier than
necessary. Move the calls to this function to the latest point possible,
just prior to notifying hardware of the new Tx packet when we bump the
tail register.
This affects i40e, iavf, igb, igc, and ixgbe.
The e100, e1000, e1000e, fm10k, and ice drivers already call the
skb_tx_timestamp() function just prior to indicating the Tx packet to
hardware, so they do not need to be changed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a call to skb_tx_timestamp in the ixgbevf_tx_map function. This
enables software timestamping for packets sent over this device driver.
The call is placed just prior to when we notify hardware of the new
packet, in order to software timestamp as close as possible to when the
hardware will transmit.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When it's possible that the PF might end up trying to send a
packet to one of its own VFs, we have to forbid IPsec offload
because the device drops the packets into a black hole.
See commit 47b6f50077 ("ixgbe: disallow IPsec Tx offload
when in SR-IOV mode") for more info.
This really is only necessary when the device is in the default
VEB mode. If instead the device is running in VEPA mode,
the packets will go through the encryption engine and out the
MAC/PHY as normal, and get "hairpinned" as needed by the switch.
So let's not block IPsec offload when in VEPA mode. To get
there with the ixgbe device, use the handy 'bridge' command:
bridge link set dev eth1 hwmode vepa
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is an earlier check to see if xdp_ring is null when configuring
the tx ring, so assuming that it can still be null, the clearing of
the xdp_ring->state currently could end up with a null pointer
dereference. Fix this by only clearing the bit if xdp_ring is not null.
Detected by CoverityScan, CID#1473795 ("Dereference after null check")
Fixes: 024aa5800f ("ixgbe: added Rx/Tx ring disable/enable functions")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
lockdep_assert_held() is better suited to checking locking requirements,
since it won't get confused when someone else holds the lock. This is
also a step towards possibly removing spin_is_locked().
Signed-off-by: Lance Roy <ldr709@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit bacd75cfac ("i40e/i40evf: Add capability exchange for
outer checksum", 2017-04-06) the i40e driver has not reported support
for IP-in-IP offloads. This likely occurred due to a bad rebase, as the
commit extracts hw_enc_features into its own variable. As part of this
change, it dropped the NETIF_F_FSO_IPXIP flags from the
netdev->hw_enc_features. This was unfortunately not caught during code
review.
Fix this by adding back the missing feature flags.
For reference, NETIF_F_GSO_IPXIP4 was added in commit 7e13318daa
("net: define gso types for IPx over IPv4 and IPv6", 2016-05-20),
replacing NETIF_F_GSO_IPIP and NETIF_F_GSO_SIT.
NETIF_F_GSO_IPXIP6 was added in commit bf2d1df395 ("intel: Add support
for IPv6 IP-in-IP offload", 2016-05-20).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull ARM SoC fixes from Olof Johansson:
"A few more fixes that have come in, and one revert of a previous fix.
I was a bit too trigger happy to enable PREEMPT on multi_v7_defconfig,
and it ended up regressing at least BeagleBone XM boards. While we get
that debugged for next merge window, let's disable it again.
Beyond that:
- Stratix change to fix multicast filtering
- Minor DT fixes for Renesas and i.MX
- Ethernet fix for a Renesas board (switching main interfaces)
- Ethernet phy regulator fix for i.MX6SX"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dts: stratix10: fix multicast filtering
ARM: defconfig: Disable PREEMPT again on multi_v7
arm64: dts: renesas: condor: switch from EtherAVB to GEther
dt-bindings: arm: Fix RZ/G2E part number
arm64: dts: renesas: r8a7795: add missing dma-names on hscif2
ARM: dts: imx6sx-sdb: Fix enet phy regulator
ARM: dts: fsl: Fix improperly quoted stdout-path values
ARM: dts: imx6sll: fix typo for fsl,imx6sll-i2c node
Pull HID fixes from Jiri Kosina:
- hid.git is moving towards group maintainership (where group is myself
and Benjamin Tissoires), therefore this pull request updates
MAINTAINERS accordingly
- fix for hid-asus config dependency from Arnd Bergmann
- two device-specific quirks for i2c-hid from Julian Sax and Kai-Heng
Feng
- other few small assorted fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: fix up .raw_event() documentation
HID: asus: fix build warning wiht CONFIG_ASUS_WMI disabled
HID: i2c-hid: add Direkt-Tek DTLAPY133-1 to descriptor override
HID: moving to group maintainership model
HID: alps: allow incoming reports when only the trackstick is opened
Revert "HID: add NOGET quirk for Eaton Ellipse MAX UPS"
HID: i2c-hid: Add a small delay after sleep command for Raydium touchpanel
HID: hiddev: fix potential Spectre v1
Fix an issue with the 32-bit range error path in `rtc_hctosys' where no
error code is set and consequently the successful preceding call result
from `rtc_read_time' is propagated to `rtc_hctosys_ret'. This in turn
makes any subsequent call to `hctosys_show' incorrectly report in sysfs
that the system time has been set from this RTC while it has not.
Set the error to ERANGE then if we can't express the result due to an
overflow.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Fixes: b3a5ac42ab ("rtc: hctosys: Ensure system time doesn't overflow time_t")
Cc: stable@vger.kernel.org # 4.17+
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When there is no IRQ configured for the RTC, the rtc-cmos code does not
support alarms, all alarm rtc_ops fail with -EIO / -EINVAL.
The rtc-core expects a rtc driver which does not support rtc alarms to
not have alarm ops at all. Otherwise the wakealarm sysfs attr will read
as empty rather then returning an error, making it impossible for
userspace to find out beforehand if alarms are supported.
A system without an IRQ for the RTC before this patch:
[root@localhost ~]# cat /sys/class/rtc/rtc0/wakealarm
[root@localhost ~]#
After this patch:
[root@localhost ~]# cat /sys/class/rtc/rtc0/wakealarm
cat: /sys/class/rtc/rtc0/wakealarm: No such file or directory
[root@localhost ~]#
This fixes gnome-session + systemd trying to use suspend-then-hibernate,
which causes systemd to abort the suspend when writing the RTC alarm fails.
BugLink: https://github.com/systemd/systemd/issues/9988
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
ARM: dts: stratix10: fix multicast filtering
On Stratix 10, the EMAC has 256 hash buckets for multicast filtering. This
needs to be specified in DTS, otherwise the stmmac driver defaults to 64
buckets and initializes the filter incorrectly. As a result, e.g. valid
IPv6 multicast traffic ends up being dropped.
* tag 'stratix10_dts_fix_for_v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: stratix10: fix multicast filtering
Signed-off-by: Olof Johansson <olof@lixom.net>
bs.bh was taken in previous ext4_xattr_block_find() call,
it should be released before re-using
Fixes: 7e01c8e542 ("ext3/4: fix uninitialized bs in ...")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org # 2.6.26
Renesas ARM Based SoC Fixes for v4.20
* R-Car V3H (r8a77980) based Condor board
- Switch from EtherAVB to GEther to match offical boards
* RZ/G2E (ra8774c0) SoC: correct documentation of part number
* R-Car H3 (r8a7795) SoC: reinstate all DMA channels on HSCIF2
* tag 'renesas-fixes-for-v4.20' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: condor: switch from EtherAVB to GEther
dt-bindings: arm: Fix RZ/G2E part number
arm64: dts: renesas: r8a7795: add missing dma-names on hscif2
Signed-off-by: Olof Johansson <olof@lixom.net>
SLIM_MSG_CLK_PAUSE_SEQ_FLG is never set in any of the slim core,
so performing a check in ngd driver is totally unnecessary.
Also this patch fixes warning about mc field overflow reported
with CoverityScan.
Making clk pause feature optional will be added to slim core in
next development cycle.
Reported-by: Colin Ian King <colin.king@canonical.com>
Fixes: 917809e228 ("slimbus: ngd: Add qcom SLIMBus NGD driver")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The order in which the frequencies are displayed in cpufreq stats
depends on the order in which the frequencies were sorted in the
frequency table provided to cpufreq core by the cpufreq driver. They can
be completely unsorted as well.
The documentation's claim that the stats will be sorted in descending
order is hence incorrect and here is an attempt to fix it.
Reported-by: Pavel <pavel2000@ngs.ru>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
