Almost entirely borrowed from the x86 code.
Main improvement is to avoid having to initialize
ts->tv_nsec to zero before the sequence loops, by
expanding timespec_add_ns().
Signed-off-by: David S. Miller <davem@davemloft.net>
Group the temperature sensor specific ops into a single structure and
assign it to hisi thermal data structure.
Change the platform data pointer to reference the specific sensor ops
instead of the probe functions.
Moving out those allow to split the code to self-encapsulate the
sensor object.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch series now has evolved to contain several related changes.
1. Updated the assorted cleanup series by Palmer.
The original cleanup patch series can be found here.
http://lists.infradead.org/pipermail/linux-riscv/2018-August/001232.html
2. Implemented decoupling linux logical CPU ids from hart id.
Some of the work has been inspired from ARM64.
Tested on QEMU & HighFive Unleashed board with/without SMP enabled.
3. Included Anup's cleanup and IPI stat patch.
All the patch series have been combined to avoid conflicts as a lot of
common code is changed different patch sets. Atish has mostly addressed
review comments and fixed checkpatch errors from Palmer's and Anup's
series.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patch set fixes up various failures in the RV32I port. The fixes
are all nominally independent, but are really only testable together
because the RV32I port fails to build without all of them. The patch
set includes:
* The removal of tishift on RV32I targets, as 128-bit integers are not
supported by the toolchain.
* The removal of swiotlb from RV32I targets, since all physical
addresses can be mapped by all hardware on all existing RV32I targets.
* The addition of ummodi3 and udivmoddi4 from an old version of GCC that
was licensed under GPLv2 as generic code, along with their use on
RV32I targets.
* A fix to our page alignment logic within ioremap for RV32I targets.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patchset adds an option, CONFIG_FPU, to enable/disable floating-
point support within the kernel. The kernel's new behavior will be as
follows:
* with CONFIG_FPU=y
All FPU codes are reserved. If no FPU is found during booting, a
global flag will be set, and those functions will be bypassed with
condition check to that flag.
* with CONFIG_FPU=n
No floating-point instructions in kernel and all related settings
are excluded.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
* Move the built-in cmdline configuration on a new menu entry "Boot
options", it doesn't make much sense to be part of the debuging menu.
* Rename "Kernel Type" menu to "Kernel features" to be more consistent with
what other architectures are using, plus "type" is a bit misleading here.
Signed-off-by: Nick Kossifidis <mick@ics.forth.gr>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This export is not only not needed, but also breaks symbol versioning
due to being an undeclared assembly export.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Here is an attempt to add the missing futex support. I started with the MIPS
version of futex.h and modified it until I got it working. I tested it on
a HiFive Unleashed running Fedora Core 29 using the fc29 4.15 version of the
kernel. This was tested against the glibc testsuite, where it fixes 14 nptl
related testsuite failures. That unfortunately only tests the cmpxchg support,
so I also used the testcase at the end of
https://lwn.net/Articles/148830/
which tests the atomic_op functionality, except that it doesn't verify that
the operations are atomic, which they obviously are. This testcase runs
successfully with the patch and fails without it.
I'm not a kernel expert, so there could be details I got wrong here. I wasn't
sure about the memory model support, so I used aqrl which seemed safest, and
didn't add fences which seemed unnecessary. I'm not sure about the copyright
statements, I left in Ralf Baechle's line because I started with his code.
Checkpatch reports some style problems, but it is the same style as the MIPS
futex.h, and the uses of ENOSYS appear correct even though it complains about
them. I don't know if any of that matters.
This patch was tested on qemu with the glibc nptl/tst-cond-except
testcase, and the wake_op testcase from above.
Signed-off-by: Jim Wilson <jimw@sifive.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add a variable and a macro to describe FP registers, assuming only D is
supported. FP code is conditional on CONFIG_FPU. The FP regs and FCSR
are copied separately to avoid copying struct padding. Tested by hand and
with the gdb testsuite.
Signed-off-by: Jim Wilson <jimw@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The RISC-V Linux port doesn't support systems that have the F extension
but don't have the D extension -- we actually don't support systems
without D either, but Alan's patch set is rectifying that soon. For now
I think we can leave this in a semi-broken state and just wait for
Alan's patch set to get merged for proper non-FPU support -- the patch
set is starting to look good, so doing something in-between doesn't seem
like it's worth the work.
I don't think it's worth fretting about support for systems with F but
not D for now: our glibc ABIs are IMAC and IMAFDC so they probably won't
end up being popular. We can always extend this in the future.
CC: Alan Kao <alankao@andestech.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
These are just hard coded in the RISC-V port, which doesn't make any
sense. We should probably be setting these from device tree entries
when they exist, but for now I think it's saner to just leave them all
as their default values.
Reviewed-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
During probe phase, the error path can be handled in one place and
use goto method to save many duplicated code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The SROT registers are initialised by the secure firmware at boot. We
don't have write access to the registers. Check if the block is enabled
before continuing.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Registers have moved around across TSENS generations. For example, the
CTRL register was at offset 0x0 in the SROT region on msm8916 but is at
offset 0x4 in newer v2 based TSENS HW blocks.
Allow passing offsets of important registers so that we can continue to
use common functions.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
On platforms whose device trees specify two address spaces for TSENS, the
second one points to the SROT registers. Initialise the SROT map on those
platforms.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The TSENS driver currently only uses a limited set of registers from the TM
address space. So it was ok to map just that set of registers and call it
"map".
We'd now like to map a second set: SROT registers to introduce new
functionality. Rename the "map" field to a more appropriate "tm_map".
The 8960 doesn't have a clear split between TM and SROT registers. To avoid
complicating the data structure, it will switchover to using tm_map for its
maps.
There is no functional change with this patch.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We've already converted over the devicetree of platforms using v2
version of the TSENS IP to use two address spaces. Now prepare to
convert over the 8916 and 8974 platforms to use separate SROT and TM
address spaces.
This patch will work with device trees with one or two address spaces
because we set the tm_offset in commit 5b1283984f ("thermal: tsens:
Add support to split up register address space into two").
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Pull spi updates from Mark Brown:
"One new core feature here, a small collection of new drivers and a
bunch of small improvements in existing drivers:
- A new CS_WORD flag for transfers where the chip select is toggled
at every word, with both a generic implementation and the ability
for controllers to do this automatically (including a DaVinci one).
- New drivers for Mediatek MT2712, Qualcomm GENI and QSPI, Spreadtrum
SPI and ST STM32 QSPI plus new IDs for several existing ones"
* tag 'spi-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (86 commits)
spi: lpspi: add imx8qxp compatible string
spi: Allow building SPI_BCM63XX_HSSPI on ARM-based SoCs
spi: omap2-mcspi: Add slave mode support
spi: omap2-mcspi: Set FIFO DMA trigger level to word length
spi: omap2-mcspi: Switch to readl_poll_timeout()
spi: spi-mem: add stm32 qspi controller
dt-bindings: spi: add stm32 qspi controller
spi: sh-msiof: document R8A779{7|8}0 bindings
spi: pic32-sqi: don't pass GFP_DMA32 to dma_alloc_coherent
MAINTAINERS: Add entry for Broadcom SPI controller
spi: sh-msiof: fix deferred probing
spi: imx: use PIO mode if size is small
spi: imx: correct wml as the last sg length
spi: imx: move wml setting to later than setup_transfer
PCI: Provide pci_match_id() with CONFIG_PCI=n
spi: Make GPIO CSs honour the SPI_NO_CS flag
spi/spi-pxa2xx: add PXA2xx SSP SPI Controller
spi: pxa2xx: Add devicetree support
spi: pxa2xx: Use an enum for type
spi: spi-geni-qcom: Add SPI driver support for GENI based QUP
...
Pull regmap updates from Mark Brown:
"A small update with a couple of new APIs that are useful for some
small sets of devices:
- Split up the single_rw flagging to map read and write separately as
some devices support bulk operations for only read or only write.
- Add a write version of the noinc API.
- Clean up the code for LOG_DEVICE a bit"
* tag 'regmap-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: use less #ifdef for LOG_DEVICE
regmap: Add regmap_noinc_write API
regmap: split up regmap_config.use_single_rw
regmap: fix comment for regmap.use_single_write
The MPC885 has SEC engine version 1.2 with the following details:
- Number of Crypto channels: 1
- Exec Units: DEU, MDEU and AESU
- Available descriptors: 00010, 00100, 00110, 01000, 11000, 11010
It is also supposed to have descriptor 00000, but it doesn't work
properly so we keep it out for the moment.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
Pull mtd updates from Boris Brezillon:
"SPI NOR core changes:
- Support non-uniform erase size
- Support controllers with limited TX fifo size
Driver changes:
- m25p80: Re-issue a WREN command after each write access
- cadence: Pass a proper dir value to dma_[un]map_single()
- fsl-qspi: Check fsl_qspi_get_seqid() return val make sure 4B
addressing opcodes are properly handled
- intel-spi: Add a new PCI entry for Ice Lake
Raw NAND core changes:
- Two batchs of cleanups of the NAND API, including:
* Deprecating a lot of interfaces (now replaced by ->exec_op()).
* Moving code in separate drivers (JEDEC, ONFI), in private files
(internals), in platform drivers, etc.
* Functions/structures reordering.
* Exclusive use of the nand_chip structure instead of the MTD one
all across the subsystem.
- Addition of the nand_wait_readrdy/rdy_op() helpers.
Raw NAND controllers drivers changes:
- Various coccinelle patches.
- Marvell:
* Use regmap_update_bits() for syscon access.
* More documentation.
* BCH failure path rework.
* More layouts to be supported.
* IRQ handler complete() condition fixed.
- Fsl_ifc:
* SRAM initialization fixed for newer controller versions.
- Denali:
* Fix licenses mismatch and use a SPDX tag.
* Set SPARE_AREA_SKIP_BYTES register to 8 if unset.
- Qualcomm:
* Do not include dma-direct.h.
- Docg4:
* Removed.
- Ams-delta:
* Use of a GPIO lookup table
* Internal machinery changes.
Raw NAND chip drivers changes:
- Toshiba:
* Add support for Toshiba memory BENAND
* Pass a single nand_chip object to the status helper.
- ESMT:
* New driver to retrieve the ECC requirements from the 5th ID
byte.
MTD changes:
- physmap cleanups/fixe
- gpio-addr-flash cleanups/fixes"
* tag 'mtd/for-4.20' of git://git.infradead.org/linux-mtd: (93 commits)
jffs2: free jffs2_sb_info through jffs2_kill_sb()
mtd: spi-nor: fsl-quadspi: fix read error for flash size larger than 16MB
mtd: spi-nor: intel-spi: Add support for Intel Ice Lake SPI serial flash
mtd: maps: gpio-addr-flash: Convert to gpiod
mtd: maps: gpio-addr-flash: Replace array with an integer
mtd: maps: gpio-addr-flash: Use order instead of size
mtd: spi-nor: fsl-quadspi: Don't let -EINVAL on the bus
mtd: devices: m25p80: Make sure WRITE_EN is issued before each write
mtd: spi-nor: Support controllers with limited TX FIFO size
mtd: spi-nor: cadence-quadspi: Use proper enum for dma_[un]map_single
mtd: spi-nor: parse SFDP Sector Map Parameter Table
mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories
mtd: rawnand: marvell: fix the IRQ handler complete() condition
mtd: rawnand: denali: set SPARE_AREA_SKIP_BYTES register to 8 if unset
mtd: rawnand: r852: fix spelling mistake "card_registred" -> "card_registered"
mtd: rawnand: toshiba: Pass a single nand_chip object to the status helper
mtd: maps: gpio-addr-flash: Use devm_* functions
mtd: maps: gpio-addr-flash: Fix ioremapped size
mtd: maps: gpio-addr-flash: Replace custom printk
mtd: physmap_of: Release resources on error
...
This patch provides arch_show_interrupts() implementation to
show IPI stats via /proc/interrupts.
Now the contents of /proc/interrupts" will look like below:
CPU0 CPU1 CPU2 CPU3
8: 17 7 6 14 SiFive PLIC 8 virtio0
10: 10 10 9 11 SiFive PLIC 10 ttyS0
IPI0: 170 673 251 79 Rescheduling interrupts
IPI1: 1 12 27 1 Function call interrupts
Signed-off-by: Anup Patel <anup@brainfault.org>
[Atish - Fixed checkpatch errors]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Changes since v2:
- Remove use of IPI_CALL_WAKEUP because it's being removed
Changes since v1:
- Add stub inline show_ipi_stats() function for !CONFIG_SMP
- Make ipi_names[] dynamically sized at compile time
- Minor beautification of ipi_names[] using tabs
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently, /proc/cpuinfo show logical CPU ID as Hart ID which
is in-correct. This patch shows CPU ID and Hart ID separately
in /proc/cpuinfo using cpuid_to_hardid_map().
With this patch, contents of /proc/cpuinfo looks as follows:
processor : 0
hart : 1
isa : rv64imafdc
mmu : sv48
processor : 1
hart : 0
isa : rv64imafdc
mmu : sv48
processor : 2
hart : 2
isa : rv64imafdc
mmu : sv48
processor : 3
hart : 3
isa : rv64imafdc
mmu : sv48
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Setup the cpu_logical_map during boot. Moreover, every SBI call
and PLIC context are based on the physical hartid. Use the logical
CPU to hartid mapping to pass correct hartid to respective functions.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently, both Linux CPU id and hart id are same.
This is not recommended as it will lead to discontinuous CPU
indexing in Linux. Moreover, kdump kernel will run from CPU0
which would be absent if we follow existing scheme.
Implement a logical mapping between Linux CPU id and hart
id to decouple these two. Always mark the boot processor as
CPU0 and all other CPUs get the logical CPU id based on their
booting order.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The secondary harts spin on couple of per cpu variables until both of
these are non-zero so it's not necessary to have any ordering here.
However, WRITE_ONCE should be used to avoid tearing.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
It's a bit confusing exactly what this function does: it actually
returns the hartid of an OF processor node, failing with -1 on invalid
nodes. I've changed the name to _hartid() in order to make that a bit
more clear, as well as adding a comment.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
[Atish: code comment formatting update]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
I'm not sure how I managed to miss this the first time, but this is much
better.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
[Atish: code comment formatting and other fixes]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently, irq is enabled before preemption disabling happens.
If the scheduler fired right here and cpu is scheduled then it
may blow up.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
[Atish: Commit text and code comment formatting update]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
We shouldn't be directly passing device tree values to userspace, both
because there could be mistakes in device trees and because the kernel
doesn't support arbitrary ISAs.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
[Atish: checkpatch fix and code comment formatting update]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
These are just hard coded in the RISC-V port, which doesn't make any
sense. We should probably be setting these from device tree entries
when they exist, but for now I think it's saner to just leave them all
as their default values.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The scause is already part of pt_regs so no need to pass
scause as separate arg to do_IRQ().
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
For 32bit, the upper 32-bit of phys_addr_t will be flushed to zero
after AND with PAGE_MASK because the data type of PAGE_MASK is
unsigned long. To fix this problem, the page alignment is done by
subtracting the page offset instead of AND with PAGE_MASK.
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add umoddi3 and udivmoddi4 support for 32-bit.
The RV32 need the umoddi3 to do modulo when the operands are long long
type, like other libraries implementation such as ucmpdi2, lshrdi3 and
so on.
I encounter the undefined reference 'umoddi3' when I use the in
house dma driver, although it is in house driver, but I think that
umoddi3 is a common function for RV32.
The udivmoddi4 and umoddi3 are copies from libgcc in gcc. There are other
functions use the udivmoddi4 in libgcc, so I separate the umoddi3 and
udivmoddi4 for flexible extension in the future.
Signed-off-by: Zong Li <zong@andestech.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Only RV64 supports swiotlb. On RV32, it don't select the SWIOTLB.
Signed-off-by: Zong Li <zong@andestech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
We expect that a kernel with CONFIG_FPU=y can still support no-FPU
machines. To do so, the kernel should first examine the existence of a
FPU, then do nothing if a FPU does exist; otherwise, it should
disable/bypass all FPU-related functions.
In this patch, a new global variable, has_fpu, is created and determined
when parsing the hardware capability from device tree during booting.
This variable is used in those FPU-related functions.
Signed-off-by: Alan Kao <alankao@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Cc: Vincent Chen <vincentc@andestech.com>
Cc: Zong Li <zong@andestech.com>
Cc: Nick Hu <nickhu@andestech.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
