This change fixes a problem where reboot on Android panics the kernel
almost every time when file systems are mounted over loop devices.
Android reboot command does:
- sync
- echo u > /proc/sysrq-trigger
- syscall_reboot
The problem is with sysrq emergency remount R/O trying to remount-ro
in wrong order.
since /data is re-mounted ro before loop devices, loop device
remount-ro fails to flush the journal and panics the kernel:
EXT4-fs (loop0): Remounting filesystem read-only
EXT4-fs (loop0): previous I/O error to superblock detected
loop: Write error at byte offset 0, length 4096.
Buffer I/O error on device loop0, logical block 0
lost page write due to I/O error on loop0
Kernel panic - not syncing: EXT4-fs panic from previous error
The fix is quite simple. In do_emergency_remount(), use
list_for_each_entry_reverse() on sb list instead of list_for_each_entry().
It makes a lot of sense to umount the file systems in reverse order in
which they were added to sb list.
Change-Id: I4370e39b5873bd16ade5d5f9ddb2704beb02a2bb
Signed-off-by: Amir Goldstein <amir@cellrox.com>
Acked-by: Oren Laadan <orenl@cellrox.com>
(cherry picked from commit 334cc257d864f112b64fb885be908e6cdd644c08)
This patch includes two trace events on generic_perform_write and
do_generic_file_read to check on the address_space mapping for the
pages to be accessed by the request.
Change-Id: Ib319b9b2c971b9e5c76645be6cfd995ef9465d77
Signed-off-by: Daniel Campello <campello@google.com>
(cherry picked from commit d3952c50853166bd04562766c9603ed86ab0da75)
Conflicts:
include/linux/pagemap.h
Per RFC 6724, section 4, "Candidate Source Addresses":
It is RECOMMENDED that the candidate source addresses be the set
of unicast addresses assigned to the interface that will be used
to send to the destination (the "outgoing" interface).
Add a sysctl to enable this behaviour.
Signed-off-by: Erik Kline <ek@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Simplified back-port of net-next 3985e8a361]
Bug: 19470192
Bug: 21832279
Bug: 22464419
Change-Id: Ib74ef945dcabe64215064f15ee1660b6524d65ce
(cherry picked from commit 0633924e7776754ccb473d649e5fa9ee45617a46)
Converting cputime_t to usec caused overflow when the value is greater
than 1 hour. Use msec and convert to unsigned long long to support bigger
range.
Bug: 22461683
Change-Id: I853fe3e8e7dbf0d3e2cc5c6f9688a5a6e1f1fb3e
Signed-off-by: Jin Qian <jinqian@google.com>
(cherry picked from commit 75bf23fe4bfb1805b411965b5ce3c4b81b957898)
Add a skip_initramfs option to allow choosing whether to boot using
the initramfs or not at runtime.
Change-Id: If30428fa748c1d4d3d7b9d97c1f781de5e4558c3
Signed-off-by: Rom Lemarchand <romlem@google.com>
(cherry picked from commit 6f36227aa43c9e4b17a2dcda6a38e79d1b00d1b5)
When the task is terminated, the cpu_power for that particular task is
added to the terminated tasks. cpu_power is set to ULLONG_MAX at this
point to avoid double accounting of the power. It is possible that before the
task releases all the resources, cpu reschedules the task or a timer
interrupt is fired. At this point we will try to add the additional time
to the process, which will cause the accounting to be skewed. This
avoids the case where we change the cpu_power when it is already set to
ULLONG_MAX.
Bug: 22064385
Change-Id: I405733725d535b0a864088516bf52fa3638ee6aa
Signed-off-by: Jin Qian <jinqian@google.com>
Signed-off-by: Ruchi Kandoi <kandoiruchi@google.com>
(cherry picked from commit fd72341df7e6e8b834f5d4ec86a30f248eb96385)
MODULE_ALIAS_CRYPTO is not defined, use MODULE_ALIAS.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Change-Id: I24803dbbbf7ac7889bc027f69af371b594eca835
(cherry picked from 5eb3cca16fcf9c62753058aaf73bb12b71acba79)
(cherry picked from commit 9645fcee58b4af5f9f9a530f0fb514e7245012a8)
Add an empty version of of_find_node_by_path().
This fixes following build error for asoc tree:
sound/soc/fsl/fsl_ssi.c: In function 'fsl_ssi_probe':
sound/soc/fsl/fsl_ssi.c:1471:2: error: implicit declaration of function 'of_find_node_by_path' [-Werror=implicit-function-declaration]
sprop = of_get_property(of_find_node_by_path("/"), "compatible", NULL);
Change-Id: Ib635dffb97877a2820fb80b99db96a285a6d2d14
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Rob Herring <robh@kernel.org>
(cherry picked from commit 9e7f1b065a312062eb8acdb1c505ddb3792b7583)
task exit.
This avoids the race where a particular process is terminating and we
read the show_uid_stats. At this time since the task_struct still exists
and we will account for the terminating process as one of the active
task, where as the stats would have been added in the task exit
callback.
Bug: 22064385
Change-Id: Id2ae04b33fcd230eda9683a41b6019d4dd8f5d85
Signed-off-by: Jin Qian <jinqian@google.com>
Signed-off-by: Ruchi Kandoi <kandoiruchi@google.com>
(cherry picked from commit ddd9aac59e0aea3d5a4df485173115e8ecb3e17d)
When ashmem_shrink is called from direct reclaim on a user thread, a
call to do_fallocate will check for permissions against the security
policy of that user thread. It can thus fail by chance if called on a
thread that isn't permitted to modify the relevant ashmem areas.
Because we know that we have a shmem file underneath, call the shmem
implementation of fallocate directly instead of going through the
user-space interface for fallocate.
FIX=DMS06243560
Area: Kernel/Linux Kernel
Bug: 21951515
Change-Id: Ie98fff18a2bdeb535cd24d4fbdd13677e12681a7
Signed-off-by: Jeff Vander Stoep <jeffv@google.com>
(cherry picked from commit 2ecc7f173a30ee7df10240d6944108252a5f5b7d)
For architectures which support a single policy for multiple cpus,
powerstats will not be initalized for all the cores. This change will
make sure powerstats is initialized for all the cores.
Also minor changes to increase code readability.
Bug: 21498425
Change-Id: I938f45e92ff6d5371c32c4d0e37274e6de66769c
Signed-off-by: Ruchi Kandoi <kandoiruchi@google.com>
(cherry picked from commit 5862c50d1970886b5b5a57b5b52ecfd6feb95ebd)
commit 3ebe138ac6 upstream.
If rbd_dev_image_probe() in rbd_dev_probe_parent() fails, header_name
is freed twice: once in rbd_dev_probe_parent() and then in its caller
rbd_dev_image_probe() (rbd_dev_image_probe() is called recursively to
handle parent images).
rbd_dev_probe_parent() is responsible for probing the parent, so it
shouldn't muck with clone's fields.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 874bbfe600 upstream.
My system keeps crashing with below message. vmstat_update() schedules a delayed
work in current cpu and expects the work runs in the cpu.
schedule_delayed_work() is expected to make delayed work run in local cpu. The
problem is timer can be migrated with NO_HZ. __queue_work() queues work in
timer handler, which could run in a different cpu other than where the delayed
work is scheduled. The end result is the delayed work runs in different cpu.
The patch makes __queue_delayed_work records local cpu earlier. Where the timer
runs doesn't change where the work runs with the change.
[ 28.010131] ------------[ cut here ]------------
[ 28.010609] kernel BUG at ../mm/vmstat.c:1392!
[ 28.011099] invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC KASAN
[ 28.011860] Modules linked in:
[ 28.012245] CPU: 0 PID: 289 Comm: kworker/0:3 Tainted: G W4.3.0-rc3+ #634
[ 28.013065] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140709_153802- 04/01/2014
[ 28.014160] Workqueue: events vmstat_update
[ 28.014571] task: ffff880117682580 ti: ffff8800ba428000 task.ti: ffff8800ba428000
[ 28.015445] RIP: 0010:[<ffffffff8115f921>] [<ffffffff8115f921>]vmstat_update+0x31/0x80
[ 28.016282] RSP: 0018:ffff8800ba42fd80 EFLAGS: 00010297
[ 28.016812] RAX: 0000000000000000 RBX: ffff88011a858dc0 RCX:0000000000000000
[ 28.017585] RDX: ffff880117682580 RSI: ffffffff81f14d8c RDI:ffffffff81f4df8d
[ 28.018366] RBP: ffff8800ba42fd90 R08: 0000000000000001 R09:0000000000000000
[ 28.019169] R10: 0000000000000000 R11: 0000000000000121 R12:ffff8800baa9f640
[ 28.019947] R13: ffff88011a81e340 R14: ffff88011a823700 R15:0000000000000000
[ 28.020071] FS: 0000000000000000(0000) GS:ffff88011a800000(0000)knlGS:0000000000000000
[ 28.020071] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 28.020071] CR2: 00007ff6144b01d0 CR3: 00000000b8e93000 CR4:00000000000006f0
[ 28.020071] Stack:
[ 28.020071] ffff88011a858dc0 ffff8800baa9f640 ffff8800ba42fe00ffffffff8106bd88
[ 28.020071] ffffffff8106bd0b 0000000000000096 0000000000000000ffffffff82f9b1e8
[ 28.020071] ffffffff829f0b10 0000000000000000 ffffffff81f18460ffff88011a81e340
[ 28.020071] Call Trace:
[ 28.020071] [<ffffffff8106bd88>] process_one_work+0x1c8/0x540
[ 28.020071] [<ffffffff8106bd0b>] ? process_one_work+0x14b/0x540
[ 28.020071] [<ffffffff8106c214>] worker_thread+0x114/0x460
[ 28.020071] [<ffffffff8106c100>] ? process_one_work+0x540/0x540
[ 28.020071] [<ffffffff81071bf8>] kthread+0xf8/0x110
[ 28.020071] [<ffffffff81071b00>] ?kthread_create_on_node+0x200/0x200
[ 28.020071] [<ffffffff81a6522f>] ret_from_fork+0x3f/0x70
[ 28.020071] [<ffffffff81071b00>] ?kthread_create_on_node+0x200/0x200
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f7effddf4 upstream.
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail. While here, move drvdata, too.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8996eafdcb upstream.
Unlike shash algorithms, ahash drivers must implement export
and import as their descriptors may contain hardware state and
cannot be exported as is. Unfortunately some ahash drivers did
not provide them and end up causing crashes with algif_hash.
This patch adds a check to prevent these drivers from registering
ahash algorithms until they are fixed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 631d8b674f upstream.
When compiling a MMU kernel with CPU_HAS_ADDRESS_SPACES=n (e.g. "MMU=y
allnoconfig": "echo CONFIG_MMU=y > allno.config && make KCONFIG_ALLCONFIG=1
allnoconfig"), we use plain "move" instead of "moves", and I got:
CC arch/m68k/lib/uaccess.o
{standard input}: Assembler messages:
{standard input}:47: Error: operands mismatch -- statement `move.b %a0,(%a1)' ignored
This happens because plain "move" doesn't support byte transfers between
memory and address registers, while "moves" does.
Fix the asm constraints for __generic_copy_from_user(),
__generic_copy_to_user(), and __clear_user() to only use data registers
when accessing userspace.
Also, relax the asm constraints for 16-bit userspace accesses in
__put_user() and __get_user(), as both "move" and "moves" do support
such transfers between memory and address registers.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 436c2a5036 ]
commit 3cc81d85ee ("asix: Don't reset PHY on if_up for ASIX 88772")
causes the ethernet on Arndale to no longer function. This appears to
be because the Arndale ethernet requires a full reset before it will
function correctly, however simply reverting the above patch causes
problems with ethtool settings getting reset.
It seems the problem is that the ethernet is not properly reset during
bind, and indeed the code in ax88772_bind that resets the device is a
very small subset of the actual ax88772_reset function. This patch uses
ax88772_reset in place of the existing reset code in ax88772_bind which
removes some code duplication and fixes the ethernet on Arndale.
It is still possible that the original patch causes some issues with
suspend and resume but that seems like a separate issue and I haven't
had a chance to test that yet.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3cc81d85ee ]
I've noticed every time the interface is set to 'up,', the kernel
reports that the link speed is set to 100 Mbps/Full Duplex, even
when ethtool is used to set autonegotiation to 'off', half
duplex, 10 Mbps.
It can be tested by:
ifconfig eth0 down
ethtool -s eth0 autoneg off speed 10 duplex half
ifconfig eth0 up
Then checking 'dmesg' for the link speed.
Signed-off-by: Michel Stam <m.stam@fugro.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 077cb37fcf ]
It seems that kernel memory can leak into userspace by a
kmalloc, ethtool_get_strings, then copy_to_user sequence.
Avoid this by using kcalloc to zero fill the copied buffer.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c7c49b8fde ]
Greg reported crashes hitting the following check in __sk_backlog_rcv()
BUG_ON(!sock_flag(sk, SOCK_MEMALLOC));
The pfmemalloc bit is currently checked in sk_filter().
This works correctly for TCP, because sk_filter() is ran in
tcp_v[46]_rcv() before hitting the prequeue or backlog checks.
For UDP or other protocols, this does not work, because the sk_filter()
is ran from sock_queue_rcv_skb(), which might be called _after_ backlog
queuing if socket is owned by user by the time packet is processed by
softirq handler.
Fixes: b4b9e35585 ("netvm: set PF_MEMALLOC as appropriate during SKB processing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Greg Thelen <gthelen@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 31b33dfb0a ]
Earlier patch 6ae459bda tried to detect void ckecksum partial
skb by comparing pull length to checksum offset. But it does
not work for all cases since checksum-offset depends on
updates to skb->data.
Following patch fixes it by validating checksum start offset
after skb-data pointer is updated. Negative value of checksum
offset start means there is no need to checksum.
Fixes: 6ae459bda ("skbuff: Fix skb checksum flag on skb pull")
Reported-by: Andrew Vagin <avagin@odin.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ae459bdaa ]
VXLAN device can receive skb with checksum partial. But the checksum
offset could be in outer header which is pulled on receive. This results
in negative checksum offset for the skb. Such skb can cause the assert
failure in skb_checksum_help(). Following patch fixes the bug by setting
checksum-none while pulling outer header.
Following is the kernel panic msg from old kernel hitting the bug.
------------[ cut here ]------------
kernel BUG at net/core/dev.c:1906!
RIP: 0010:[<ffffffff81518034>] skb_checksum_help+0x144/0x150
Call Trace:
<IRQ>
[<ffffffffa0164c28>] queue_userspace_packet+0x408/0x470 [openvswitch]
[<ffffffffa016614d>] ovs_dp_upcall+0x5d/0x60 [openvswitch]
[<ffffffffa0166236>] ovs_dp_process_packet_with_key+0xe6/0x100 [openvswitch]
[<ffffffffa016629b>] ovs_dp_process_received_packet+0x4b/0x80 [openvswitch]
[<ffffffffa016c51a>] ovs_vport_receive+0x2a/0x30 [openvswitch]
[<ffffffffa0171383>] vxlan_rcv+0x53/0x60 [openvswitch]
[<ffffffffa01734cb>] vxlan_udp_encap_recv+0x8b/0xf0 [openvswitch]
[<ffffffff8157addc>] udp_queue_rcv_skb+0x2dc/0x3b0
[<ffffffff8157b56f>] __udp4_lib_rcv+0x1cf/0x6c0
[<ffffffff8157ba7a>] udp_rcv+0x1a/0x20
[<ffffffff8154fdbd>] ip_local_deliver_finish+0xdd/0x280
[<ffffffff81550128>] ip_local_deliver+0x88/0x90
[<ffffffff8154fa7d>] ip_rcv_finish+0x10d/0x370
[<ffffffff81550365>] ip_rcv+0x235/0x300
[<ffffffff8151ba1d>] __netif_receive_skb+0x55d/0x620
[<ffffffff8151c360>] netif_receive_skb+0x80/0x90
[<ffffffff81459935>] virtnet_poll+0x555/0x6f0
[<ffffffff8151cd04>] net_rx_action+0x134/0x290
[<ffffffff810683d8>] __do_softirq+0xa8/0x210
[<ffffffff8162fe6c>] call_softirq+0x1c/0x30
[<ffffffff810161a5>] do_softirq+0x65/0xa0
[<ffffffff810687be>] irq_exit+0x8e/0xb0
[<ffffffff81630733>] do_IRQ+0x63/0xe0
[<ffffffff81625f2e>] common_interrupt+0x6e/0x6e
Reported-by: Anupam Chanda <achanda@vmware.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9f389e3567 ]
AF_UNIX sockets now return multiple skbs from recv() when MSG_PEEK flag
is set.
This is referenced in kernel bugzilla #12323 @
https://bugzilla.kernel.org/show_bug.cgi?id=12323
As described both in the BZ and lkml thread @
http://lkml.org/lkml/2008/1/8/444 calling recv() with MSG_PEEK on an
AF_UNIX socket only reads a single skb, where the desired effect is
to return as much skb data has been queued, until hitting the recv
buffer size (whichever comes first).
The modified MSG_PEEK path will now move to the next skb in the tree
and jump to the again: label, rather than following the natural loop
structure. This requires duplicating some of the loop head actions.
This was tested using the python socketpair python code attached to
the bugzilla issue.
Signed-off-by: Aaron Conole <aconole@bytheb.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4613012db1 ]
As suggested by Eric Dumazet this change replaces the
#define with a static inline function to enjoy
complaints by the compiler when misusing the API.
Signed-off-by: Aaron Conole <aconole@bytheb.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 06a15f51cf ]
There is a small chance that tunnel_free() is called before tunnel->del_work scheduled
resulting in a zero pointer dereference.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix NULL pointer to chan_id while requsting
external dma channel failed.
Change-Id: I0abe1acb0a892cbaec0cadb24fe215b46e2e9abb
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
commit 15e3d5a285 upstream.
3w controller don't dma map small single SGL entry commands but instead
bounce buffer them. Add a helper to identify these commands and don't
call scsi_dma_unmap for them.
Based on an earlier patch from James Bottomley.
Fixes: 118c85 ("3w-9xxx: fix command completion race")
Reported-by: Tóth Attila <atoth@atoth.sote.hu>
Tested-by: Tóth Attila <atoth@atoth.sote.hu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1d562acc7 upstream.
Here is a patch to make speakup-r work again.
It broke in 3.6 due to commit 4369c64c79
"Input: Send events one packet at a time)
The problem was that the fakekey.c routine to fake a down arrow no
longer functioned properly and putting the input_sync fixed it.
Fixes: 4369c64c79
Acked-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: John Covici <covici@ccs.covici.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bffa1503c upstream.
The cleaner policy doesn't make use of the per cache block hint space in
the metadata (unlike the other policies). When switching from the
cleaner policy to mq or smq a NULL pointer crash (in dm_tm_new_block)
was observed. The crash was caused by bugs in dm-cache-metadata.c
when trying to skip creation of the hint btree.
The minimal fix is to change hint size for the cleaner policy to 4 bytes
(only hint size supported).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff47ab4ff3 upstream.
The 64bit __copy_{from,to}_user_inatomic always called
copy_from_user_generic, but skipped the special optimizations for 1/2/4/8
byte accesses.
This especially hurts the futex call, which accesses the 4 byte futex
user value with a complicated fast string operation in a function call,
instead of a single movl.
Use __copy_{from,to}_user for _inatomic instead to get the same
optimizations. The only problem was the might_fault() in those functions.
So move that to new wrapper and call __copy_{f,t}_user_nocheck()
from *_inatomic directly.
32bit already did this correctly by duplicating the code.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/1376687844-19857-2-git-send-email-andi@firstfloor.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95c2b17534 upstream.
Per-IRQ directories in procfs are created only when a handler is first
added to the irqdesc, not when the irqdesc is created. In the case of
a shared IRQ, multiple tasks can race to create a directory. This
race condition seems to have been present forever, but is easier to
hit with async probing.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Link: http://lkml.kernel.org/r/1443266636.2004.2.camel@decadent.org.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Backports of 41fc014332 ("fib_rules: fix fib rule dumps across
multiple skbs") introduced a regression in "ip rule show" - it ends up
dumping the first rule over and over and never exiting, because 3.19
and earlier are missing commit 053c095a82 ("netlink: make
nlmsg_end() and genlmsg_end() void"), so fib_nl_fill_rule() ends up
returning skb->len (i.e. > 0) in the success case.
Fix this by checking the return code for < 0 instead of != 0.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
