This patch read the rgmii tx and rx delay from device tree and stored it
in the ksz_port. It applies the rgmii delay to the xmii tune adjust
register based on the interface selected in phylink mac config. There
are two rgmii port in LAN937x and value to be loaded in the register
vary depends on the port selected.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the common ksz_set_xmii function for ksz series switch
and update the lan937x code phylink mac config. The register address for
the ksz8795 is Port 5 Interface control 6 and for all other switch is
xMII Control 1.
The bit value for selecting the interface is same for
KSZ8795 and KSZ9893 are same. The bit values for KSZ9477 and lan973x are
same. So, this patch add the bit value for each switches in
ksz_chip_data and configure the registers based on the chip id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the support for common phylink mac link up for the ksz
series switch. The register address, bit position and values are
configured based on the chip id to the dev->info structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add common function for configuring the Full/Half duplex and
transmit/receive flow control. KSZ8795 uses the Global control register
4 for configuring the duplex and flow control, whereas all other KSZ9477
based switch uses the xMII Control 0 register.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the function for configuring the 100/10Mbps speed
selection for the ksz switches. KSZ8795 switch uses Global control 4
register 0x06 bit 4 for choosing 100/10Mpbs. Other switches uses xMII
control 1 0xN300 for it.
For KSZ8795, if the bit is set then 10Mbps is chosen and if bit is
clear then 100Mbps chosen. For all other switches it is other way
around, if the bit is set then 100Mbps is chosen.
So, this patch add the generic function for ksz switch to select the
100/10Mbps speed selection. While configuring, first it disables the
gigabit functionality and then configure the respective speed.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add helper function for setting and getting the gigabit
enable for the ksz series switch. KSZ8795 switch has different register
address compared to all other ksz switches. KSZ8795 series uses the Port
5 Interface control 6 Bit 6 for configuring the 1Gbps or 100/10Mbps
speed selection. All other switches uses the xMII control 1 0xN301
register Bit6 for gigabit.
Further, for KSZ8795 & KSZ9893 switches if bit 1 then 1Gbps is chosen
and if bit 0 then 100/10Mbps is chosen. It is other way around for
other switches bit 0 is for 1Gbps. So, this patch implements the common
function for configuring the gigabit set and get capability.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seth has been integral in the design and implementation of idmapped
mounts and was the main architect behind the s_user_ns work which
ultimately made filesystems such as FUSE and overlayfs available in
containers. He continues to be active in both development and review.
I'm very happy he decided to maintain this feature. He has my full
trust.
Link: https://lore.kernel.org/r/20220726141615.1046027-1-brauner@kernel.org
Cc: Seth Forshee <sforshee@digitalocean.com>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Convert the rtw_pwr_wakeup function to use 0 on success and an appropriate
error code on error. For the first failure block where ips_leave is
invoked, use -ENOMEM as this is the main cause of failure here anyway.
For the second failure block, use -EBUSY, as it seems the most
appropriate.
Finally, within the functions rtw_wx_set_mode, rtw_wx_set_wap,
rtw_wx_set_scan and rtw_wx_set_essid, pass the error code on from
rtw_pwr_wakeup as appropriate now that it is converted.
This gets the driver closer to removal of the non-standard _SUCCESS and
_FAIL definitions, which are inverted compared to the standard in-kernel
error code mechanism.
Tested-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> # Edimax N150
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220725220745.12739-1-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function dump_chip_info() is only used in rtl8188e_hal_init.c.
Make it static to reduce the driver object file size by 281 bytes.
before:
text data bss dec hex filename
530606 43897 7072 581575 8dfc7 drivers/staging/r8188eu/r8188eu.o
after:
text data bss dec hex filename
530405 43817 7072 581294 8deae drivers/staging/r8188eu/r8188eu.o
Tested-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> # Edimax N150
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Link: https://lore.kernel.org/r/20220724182520.7794-1-straube.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a report that kernel oops happen from idr_remove().
kernel: BUG: kernel NULL pointer dereference, address: 0000000000000010
kernel: RIP: 0010:idr_remove+0x1/0x20
kernel: __ksmbd_close_fd+0xb2/0x2d0 [ksmbd]
kernel: ksmbd_vfs_read+0x91/0x190 [ksmbd]
kernel: ksmbd_fd_put+0x29/0x40 [ksmbd]
kernel: smb2_read+0x210/0x390 [ksmbd]
kernel: __process_request+0xa4/0x180 [ksmbd]
kernel: __handle_ksmbd_work+0xf0/0x290 [ksmbd]
kernel: handle_ksmbd_work+0x2d/0x50 [ksmbd]
kernel: process_one_work+0x21d/0x3f0
kernel: worker_thread+0x50/0x3d0
kernel: rescuer_thread+0x390/0x390
kernel: kthread+0xee/0x120
kthread_complete_and_exit+0x20/0x20
kernel: ret_from_fork+0x22/0x30
While accessing files, If connection is disconnected, windows send
session setup request included previous session destroy. But while still
processing requests on previous session, this request destroy file
table, which mean file table idr will be freed and set to NULL.
So kernel oops happen from ft->idr in __ksmbd_close_fd().
This patch don't directly destroy session in destroy_previous_session().
It just set to KSMBD_SESS_EXITING so that connection will be
terminated after finishing the rest of requests.
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Reviewed-by: Hyunchul Lee <hyc.lee@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
New subflows are created within the kernel using O_NONBLOCK, so
EINPROGRESS is the expected return value from kernel_connect().
__mptcp_subflow_connect() has the correct logic to consider EINPROGRESS
to be a successful case, but it has also used that error code as its
return value.
Before v5.19 this was benign: all the callers ignored the return
value. Starting in v5.19 there is a MPTCP_PM_CMD_SUBFLOW_CREATE generic
netlink command that does use the return value, so the EINPROGRESS gets
propagated to userspace.
Make __mptcp_subflow_connect() always return 0 on success instead.
Fixes: ec3edaa7ca ("mptcp: Add handling of outgoing MP_JOIN requests")
Fixes: 702c2f646d ("mptcp: netlink: allow userspace-driven subflow establishment")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Link: https://lore.kernel.org/r/20220725205231.87529-1-mathew.j.martineau@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Westphal says:
====================
netfilter updates for net
Three late fixes for netfilter:
1) If nf_queue user requests packet truncation below size of l3 header,
we corrupt the skb, then crash. Reject such requests.
2) add cond_resched() calls when doing cycle detection in the
nf_tables graph. This avoids softlockup warning with certain
rulesets.
3) Reject rulesets that use nftables 'queue' expression in family/chain
combinations other than those that are supported. Currently the ruleset
will load, but when userspace attempts to reinject you get WARN splat +
packet drops.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nft_queue: only allow supported familes and hooks
netfilter: nf_tables: add rescheduling points during loop detection walks
netfilter: nf_queue: do not allow packet truncation below transport header offset
====================
Link: https://lore.kernel.org/r/20220726192056.13497-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- Fix early wakeup after suspend
- Fix double free on error
- Fix use-after-free on l2cap_chan_put
* tag 'for-net-2022-07-26' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: L2CAP: Fix use-after-free caused by l2cap_chan_put
Bluetooth: Always set event mask on suspend
Bluetooth: mgmt: Fix double free on error path
====================
Link: https://lore.kernel.org/r/20220726221328.423714-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch removes XDWRITEREAD support because it never fully worked when
it was added in the initial LIO merge and it's been fully broken since 2013
from commit a289008749 ("target: Add compare_and_write_post() completion
callback fall through").
The two issues above are:
1. XDWRITEREAD support was just never completed when LIO was merged. We
never did the DISABLE WRITE check and so we never write data out.
2. Since the commit above, we never complete the command. After we do the
XOR, we return from xdreadwrite_callback and that's it. We never send a
response for the command, so the command will always time out and fail.
Since this has been fully broken for almost nine years this patch just
removes emulated support.
Link: https://lore.kernel.org/r/20220726235339.14551-1-michael.christie@oracle.com
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull misc fixes from Andrew Morton:
"Thirteen hotfixes.
Eight are cc:stable and the remainder are for post-5.18 issues or are
too minor to warrant backporting"
* tag 'mm-hotfixes-stable-2022-07-26' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mailmap: update Gao Xiang's email addresses
userfaultfd: provide properly masked address for huge-pages
Revert "ocfs2: mount shared volume without ha stack"
hugetlb: fix memoryleak in hugetlb_mcopy_atomic_pte
fs: sendfile handles O_NONBLOCK of out_fd
ntfs: fix use-after-free in ntfs_ucsncmp()
secretmem: fix unhandled fault in truncate
mm/hugetlb: separate path for hwpoison entry in copy_hugetlb_page_range()
mm: fix missing wake-up event for FSDAX pages
mm: fix page leak with multiple threads mapping the same page
mailmap: update Seth Forshee's email address
tmpfs: fix the issue that the mount and remount results are inconsistent.
mm: kfence: apply kmemleak_ignore_phys on early allocated pool
RFC7143 states that Initiator decides what type of authentication to
use:
The initiator MUST continue with:
CHAP_N=<N> CHAP_R=<R>
or, if it requires target authentication, with:
CHAP_N=<N> CHAP_R=<R> CHAP_I=<I> CHAP_C=<C>
Allow one way authentication if mutual authentication is configured. That
passes some tests from Windows HLK for Mutual CHAP with iSNS.
Link: https://lore.kernel.org/r/20220718152555.17084-5-d.bogdanov@yadro.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable length SCSI commands are transferred over iSCSI via two CDB
buffers - in Basic Header Segment and in Additional Header Segment (AHS).
Since AHS is not supported yet, a target reads just BHS (48 byte) from TCP
and treats the remaining octets as a next new iSCSI PDU that causes
protocol errors.
Add support for the Extended CDB AHS type.
Link: https://lore.kernel.org/r/20220718152555.17084-2-d.bogdanov@yadro.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a device management command completion happens after
wait_for_completion_timeout() times out and before ufshcd_clear_cmds() is
called, then the completion code may crash on the complete() call in
__ufshcd_transfer_req_compl().
Fix the following crash:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
Call trace:
complete+0x64/0x178
__ufshcd_transfer_req_compl+0x30c/0x9c0
ufshcd_poll+0xf0/0x208
ufshcd_sl_intr+0xb8/0xf0
ufshcd_intr+0x168/0x2f4
__handle_irq_event_percpu+0xa0/0x30c
handle_irq_event+0x84/0x178
handle_fasteoi_irq+0x150/0x2e8
__handle_domain_irq+0x114/0x1e4
gic_handle_irq.31846+0x58/0x300
el1_irq+0xe4/0x1c0
efi_header_end+0x110/0x680
__irq_exit_rcu+0x108/0x124
__handle_domain_irq+0x118/0x1e4
gic_handle_irq.31846+0x58/0x300
el1_irq+0xe4/0x1c0
cpuidle_enter_state+0x3ac/0x8c4
do_idle+0x2fc/0x55c
cpu_startup_entry+0x84/0x90
kernel_init+0x0/0x310
start_kernel+0x0/0x608
start_kernel+0x4ec/0x608
Link: https://lore.kernel.org/r/20220720170228.1598842-1-bvanassche@acm.org
Fixes: 5a0b0cb9be ("[SCSI] ufs: Add support for sending NOP OUT UPIU")
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During system shutdown or reboot, mpt3sas will reset the firmware back to
ready state. However, the driver leaves running a watchdog work item
intended to keep the firmware in operational state. This causes a second,
unneeded reset on shutdown and moves the firmware back to operational
instead of in ready state as intended. And if the mpt3sas_fwfault_debug
module parameter is set, this extra reset also panics the system.
mpt3sas's scsih_shutdown needs to stop the watchdog before resetting the
firmware back to ready state.
Link: https://lore.kernel.org/r/20220722142448.6289-1-djeffery@redhat.com
Fixes: fae21608c3 ("scsi: mpt3sas: Transition IOC to Ready state during shutdown")
Tested-by: Laurence Oberman <loberman@redhat.com>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I've been in Alibaba Cloud for more than one year, mainly to address
cloud-native challenges (such as high-performance container images) for
open source communities.
Update my email addresses on behalf of my current employer (Alibaba Cloud)
to support all my (team) work in this area. Also add an outdated
@redhat.com address of me.
Link: https://lkml.kernel.org/r/20220719154246.62970-1-xiang@kernel.org
Signed-off-by: Gao Xiang <xiang@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Commit 824ddc601a ("userfaultfd: provide unmasked address on
page-fault") was introduced to fix an old bug, in which the offset in the
address of a page-fault was masked. Concerns were raised - although were
never backed by actual code - that some userspace code might break because
the bug has been around for quite a while. To address these concerns a
new flag was introduced, and only when this flag is set by the user,
userfaultfd provides the exact address of the page-fault.
The commit however had a bug, and if the flag is unset, the offset was
always masked based on a base-page granularity. Yet, for huge-pages, the
behavior prior to the commit was that the address is masked to the
huge-page granulrity.
While there are no reports on real breakage, fix this issue. If the flag
is unset, use the address with the masking that was done before.
Link: https://lkml.kernel.org/r/20220711165906.2682-1-namit@vmware.com
Fixes: 824ddc601a ("userfaultfd: provide unmasked address on page-fault")
Signed-off-by: Nadav Amit <namit@vmware.com>
Reported-by: James Houghton <jthoughton@google.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: James Houghton <jthoughton@google.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Replace headers_install with headers as kselftest uses the header
files from within the kernel tree rather than from a system-wide
installation.
We can still run this directly:
$ make O=build kselftest-all
and when building from the selftests directory:
$ make O=build headers
$ make O=build -C tools/testing/selftests all
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Reported-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
