Johannes Berg says:
====================
A handful of fixes:
* hwsim radio dump wasn't working for the first radio
* mesh was updating statistics incorrectly
* a netlink message allocation was possibly too short
* wiphy name limit was still too long
* in certain cases regdb query could find a NULL pointer
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to invoke pci_disable_device() when errors occur in
pcnet32_probe_pci().
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
ILT entry requires 12 bit right shifted physical address.
Existing mask for ILT entry of physical address i.e.
ILT_ENTRY_PHY_ADDR_MASK is not sufficient to handle 64bit
address because upper 8 bits of 64 bit address were getting
masked which resulted in completer abort error on
PCIe bus due to invalid address.
Fix that mask to handle 64bit physical address.
Fixes: fe56b9e6a8 ("qed: Add module with basic common support")
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In divasmain.c, the function divas_write() firstly invokes the function
diva_xdi_open_adapter() to open the adapter that matches with the adapter
number provided by the user, and then invokes the function diva_xdi_write()
to perform the write operation using the matched adapter. The two functions
diva_xdi_open_adapter() and diva_xdi_write() are located in diva.c.
In diva_xdi_open_adapter(), the user command is copied to the object 'msg'
from the userspace pointer 'src' through the function pointer 'cp_fn',
which eventually calls copy_from_user() to do the copy. Then, the adapter
number 'msg.adapter' is used to find out a matched adapter from the
'adapter_queue'. A matched adapter will be returned if it is found.
Otherwise, NULL is returned to indicate the failure of the verification on
the adapter number.
As mentioned above, if a matched adapter is returned, the function
diva_xdi_write() is invoked to perform the write operation. In this
function, the user command is copied once again from the userspace pointer
'src', which is the same as the 'src' pointer in diva_xdi_open_adapter() as
both of them are from the 'buf' pointer in divas_write(). Similarly, the
copy is achieved through the function pointer 'cp_fn', which finally calls
copy_from_user(). After the successful copy, the corresponding command
processing handler of the matched adapter is invoked to perform the write
operation.
It is obvious that there are two copies here from userspace, one is in
diva_xdi_open_adapter(), and one is in diva_xdi_write(). Plus, both of
these two copies share the same source userspace pointer, i.e., the 'buf'
pointer in divas_write(). Given that a malicious userspace process can race
to change the content pointed by the 'buf' pointer, this can pose potential
security issues. For example, in the first copy, the user provides a valid
adapter number to pass the verification process and a valid adapter can be
found. Then the user can modify the adapter number to an invalid number.
This way, the user can bypass the verification process of the adapter
number and inject inconsistent data.
This patch reuses the data copied in
diva_xdi_open_adapter() and passes it to diva_xdi_write(). This way, the
above issues can be avoided.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is no license information in the header of
this file.
The MODULE_LICENSE field contains ("GPL"), which means
GNU Public License v2 or later, so add a corresponding
SPDX license identifier.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 6335698e24 the radio with idx of 0
will not get dumped in HWSIM_CMD_GET_RADIO because of the last_idx
checks. Offset cb->args[0] by 1 similarly to what is done in nl80211.c.
Fixes: 6335698e24 ("mac80211_hwsim: add generation count for netlink dump operation")
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
1) Fix refcounting bug for connections in on-packet scheduling mode of
IPVS, from Julian Anastasov.
2) Set network header properly in AF_PACKET's packet_snd, from Willem
de Bruijn.
3) Fix regressions in 3c59x by converting to generic DMA API. It was
relying upon the hack that the PCI DMA interfaces would accept NULL
for EISA devices. From Christoph Hellwig.
4) Remove RDMA devices before unregistering netdev in QEDE driver, from
Michal Kalderon.
5) Use after free in TUN driver ptr_ring usage, from Jason Wang.
6) Properly check for missing netlink attributes in SMC_PNETID
requests, from Eric Biggers.
7) Set DMA mask before performaing any DMA operations in vmxnet3
driver, from Regis Duchesne.
8) Fix mlx5 build with SMP=n, from Saeed Mahameed.
9) Classifier fixes in bcm_sf2 driver from Florian Fainelli.
10) Tuntap use after free during release, from Jason Wang.
11) Don't use stack memory in scatterlists in tls code, from Matt
Mullins.
12) Not fully initialized flow key object in ipv4 routing code, from
David Ahern.
13) Various packet headroom bug fixes in ip6_gre driver, from Petr
Machata.
14) Remove queues from XPS maps using correct index, from Amritha
Nambiar.
15) Fix use after free in sock_diag, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (64 commits)
net: ip6_gre: fix tunnel metadata device sharing.
cxgb4: fix offset in collecting TX rate limit info
net: sched: red: avoid hashing NULL child
sock_diag: fix use-after-free read in __sk_free
sh_eth: Change platform check to CONFIG_ARCH_RENESAS
net: dsa: Do not register devlink for unused ports
net: Fix a bug in removing queues from XPS map
bpf: fix truncated jump targets on heavy expansions
bpf: parse and verdict prog attach may race with bpf map update
bpf: sockmap update rollback on error can incorrectly dec prog refcnt
net: test tailroom before appending to linear skb
net: ip6_gre: Fix ip6erspan hlen calculation
net: ip6_gre: Split up ip6gre_changelink()
net: ip6_gre: Split up ip6gre_newlink()
net: ip6_gre: Split up ip6gre_tnl_change()
net: ip6_gre: Split up ip6gre_tnl_link_config()
net: ip6_gre: Fix headroom request in ip6erspan_tunnel_xmit()
net: ip6_gre: Request headroom in __gre6_xmit()
selftests/bpf: check return value of fopen in test_verifier.c
erspan: fix invalid erspan version.
...
Pull parisc fixlets from Helge Deller:
"Three small section mismatch fixes, one of them was found by 0-day
test infrastructure"
* 'parisc-4.17-5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Move ccio_cujo20_fixup() into init section
parisc: Move setup_profiling_timer() out of init section
parisc: Move find_pa_parent_type() out of init section
Pull EFI fixes from Thomas Gleixner:
- Use explicitely sized type for the romimage pointer in the 32bit EFI
protocol struct so a 64bit kernel does not expand it to 64bit. Ditto
for the 64bit struct to avoid the reverse issue on 32bit kernels.
- Handle randomized tex offset correctly in the ARM64 EFI stub to avoid
unaligned data resulting in stack corruption and other hard to
diagnose wreckage.
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/libstub/arm64: Handle randomized TEXT_OFFSET
efi: Avoid potential crashes, fix the 'struct efi_pci_io_protocol_32' definition for mixed mode
Pull ARM SoC fixes from Olof Johansson:
"A handful of fixes. I've been queuing them up a bit too long so the
list is longer than it otherwise would have been spread out across a
few -rcs.
In general, it's a scattering of fixes across several platforms,
nothing truly serious enough to point out.
There's a slightly larger batch of them for the Davinci platforms due
to work to bring them back to life after some time, so there's a
handful of regressions, some of them going back very far, others more
recent.
There's also a few patches fixing DT on Renesas platforms since they
changed some bindings without remaining backwards compatible,
splitting up describing LVDS as a proper bridge instead of having it
as part of the display unit.
We could push for them to be backwards compatible with old device
trees, but it's likely to regress eventually if nobody's actually
using said compatibility"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
ARM: davinci: board-dm646x-evm: set VPIF capture card name
ARM: davinci: board-dm646x-evm: pass correct I2C adapter id for VPIF
ARM: davinci: dm646x: fix timer interrupt generation
ARM: keystone: fix platform_domain_notifier array overrun
arm64: dts: exynos: Fix interrupt type for I2S1 device on Exynos5433
ARM: dts: imx51-zii-rdu1: fix touchscreen bindings
firmware: arm_scmi: Use after free in scmi_create_protocol_device()
ARM: dts: cygnus: fix irq type for arm global timer
Revert "ARM: dts: logicpd-som-lv: Fix pinmux controller references"
tee: check shm references are consistent in offset/size
tee: shm: fix use-after-free via temporarily dropped reference
ARM: dts: imx7s: Pass the 'fsl,sec-era' property
ARM: dts: tegra20: Revert "Fix ULPI regression on Tegra20"
ARM: dts: correct missing "compatible" entry for ti81xx SoCs
ARM: OMAP1: ams-delta: fix deferred_fiq handler
arm64: tegra: Make BCM89610 PHY interrupt as active low
ARM: davinci: fix GPIO lookup for I2C
ARM: dts: logicpd-som-lv: Fix pinmux controller references
ARM: dts: logicpd-som-lv: Fix Audio Mute
ARM: dts: logicpd-som-lv: Fix WL127x Startup Issues
...
When CONFIG_RANDOMIZE_TEXT_OFFSET=y, TEXT_OFFSET is an arbitrary
multiple of PAGE_SIZE in the interval [0, 2MB).
The EFI stub does not account for the potential misalignment of
TEXT_OFFSET relative to EFI_KIMG_ALIGN, and produces a randomized
physical offset which is always a round multiple of EFI_KIMG_ALIGN.
This may result in statically allocated objects whose alignment exceeds
PAGE_SIZE to appear misaligned in memory. This has been observed to
result in spurious stack overflow reports and failure to make use of
the IRQ stacks, and theoretically could result in a number of other
issues.
We can OR in the low bits of TEXT_OFFSET to ensure that we have the
necessary offset (and hence preserve the misalignment of TEXT_OFFSET
relative to EFI_KIMG_ALIGN), so let's do that.
Reported-by: Kim Phillips <kim.phillips@arm.com>
Tested-by: Kim Phillips <kim.phillips@arm.com>
[ardb: clarify comment and commit log, drop unneeded parens]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 6f26b36711 ("arm64: kaslr: increase randomization granularity")
Link: http://lkml.kernel.org/r/20180518140841.9731-2-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 platform driver fix from Darren Hart:
"Remove the last of the "select DELL_SMBIOS" references in the Kconfig"
* tag 'platform-drivers-x86-v4.17-3' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: DELL_WMI use depends on instead of select for DELL_SMBIOS
Pull clk fixes from Stephen Boyd:
- a modified revert of a patch that made new choices come out for a
couple stm32 clk drivers that really always need to be there when
that particular machine is compiled in
- boot fix on i.MX for Stefan who noticed odd behavior from the
critical flag patch that came in during the merge window
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: stm32: fix: stm32 clock drivers are not compiled by default
clk: imx6ull: use OSC clock during AXI rate change
If DELL_WMI "select"s DELL_SMBIOS, the DELL_SMBIOS dependencies are
ignored and it is still possible to end up with unmet direct
dependencies.
Change the select to a depends on.
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Correct the indirect register offsets in collecting TX rate limit info
in UP CIM logs.
Also, T5 doesn't support these indirect register offsets, so remove
them from collection logic.
Fixes: be6e36d916 ("cxgb4: collect TX rate limit info in UP CIM logs")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 9b5ba0df4e ("ARM: shmobile: Introduce ARCH_RENESAS")
is CONFIG_ARCH_RENESAS a more appropriate platform check than the legacy
CONFIG_ARCH_SHMOBILE, hence use the former.
Renesas SuperH SH-Mobile SoCs are still covered by the CONFIG_CPU_SH4
check.
This will allow to drop ARCH_SHMOBILE on ARM and ARM64 in the near
future.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull powerpc fixes from Michael Ellerman:
"Just three commits.
The two cxl ones are not fixes per se, but they modify code that was
added this cycle so that it will work with a recent firmware change.
And then a fix for a recent commit that added sleeps in the NVRAM
code, which needs to be more careful and not sleep if eg. we're called
in the panic() path.
Thanks to Nicholas Piggin, Philippe Bergheaud, Christophe Lombard"
* tag 'powerpc-4.17-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv: Fix NVRAM sleep in invalid context when crashing
cxl: Report the tunneled operations status
cxl: Set the PBCQ Tunnel BAR register when enabling capi mode
Pull ACPI fix from Rafael Wysocki:
"Fix an ACPICA regression introduced in this cycle and related to the
handling of package objects loaded by the Load and loadTable AML
operators that are not initialized properly after recent changes (Bob
Moore)"
* tag 'acpi-4.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: Add deferred package support for the Load and loadTable operators
Pull power management fix from Rafael Wysocki:
"Fix Kconfig dependencies of the armada-37xx cpufreq driver (Miquel
Raynal)"
* tag 'pm-4.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: armada-37xx: driver relies on cpufreq-dt
Pull USB fixes from Greg KH:
"Here are some USB driver fixes fro 4.17-rc6.
They resolve some reported bugs in the musb driver, the xhci driver,
and a number of small fixes for the usbip driver.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usbip: usbip_host: fix bad unlock balance during stub_probe()
usbip: usbip_host: fix NULL-ptr deref and use-after-free errors
usbip: usbip_host: run rebind from exit when module is removed
usbip: usbip_host: delete device from busid_table after rebind
usbip: usbip_host: refine probe and disconnect debug msgs to be useful
usb: musb: fix remote wakeup racing with suspend
xhci: Fix USB3 NULL pointer dereference at logical disconnect.
Pull block fix from Jens Axboe:
"Single fix this time, from Coly, fixing a failure case when
CONFIG_DEBUGFS isn't enabled"
* tag 'for-linus-20180518' of git://git.kernel.dk/linux-block:
bcache: return 0 from bch_debug_init() if CONFIG_DEBUG_FS=n
Pull spi fixes from Mark Brown:
"A small collection of fixes accumilated since the merge window, all
fairly small and driver specific"
* tag 'spi-fix-v4.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: bcm2835aux: ensure interrupts are enabled for shared handler
spi: bcm-qspi: Always read and set BSPI_MAST_N_BOOT_CTRL
spi: bcm-qspi: Avoid setting MSPI_CDRAM_PCS for spi-nor master
spi: pxa2xx: Allow 64-bit DMA
spi: cadence: Add usleep_range() for cdns_spi_fill_tx_fifo()
spi: sh-msiof: Fix bit field overflow writes to TSCR/RSCR
spi: imx: Update MODULE_DESCRIPTION to "SPI Controller driver"
Pull mtd fixes from Boris Brezillon:
"NAND fixes:
- Fix read path of the Marvell NAND driver
- Make sure we don't pass a u64 to ndelay()
CFI fix:
- Fix the map_word_andequal() implementation"
* tag 'mtd/fixes-for-4.17-rc6' of git://git.infradead.org/linux-mtd:
mtd: rawnand: Fix return type of __DIVIDE() when called with 32-bit
mtd: rawnand: marvell: Fix read logic for layouts with ->nchunks > 2
mtd: Fix comparison in map_word_andequal()
Pull drm fixes from Dave Airlie:
"Pretty quiet week again: one vmwgfx regression fix, one core buffer
overflow fix, one vc4 leak fix and three i915 fixes"
* tag 'drm-fixes-for-v4.17-rc6' of git://people.freedesktop.org/~airlied/linux:
drm/dumb-buffers: Integer overflow in drm_mode_create_ioctl()
drm/i915/gen9: Add WaClearHIZ_WM_CHICKEN3 for bxt and glk
drm/vmwgfx: Set dmabuf_size when vmw_dmabuf_init is successful
drm/vc4: Fix leak of the file_priv that stored the perfmon.
drm/i915/execlists: Use rmb() to order CSB reads
drm/i915/userptr: reject zero user_size
drm: Match sysfs name in link removal to link creation
- Userptr IOCTL zero size check (Matt)
- Two hardware quirk fixes (Michel & Chris)
* tag 'drm-intel-fixes-2018-05-17' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915/gen9: Add WaClearHIZ_WM_CHICKEN3 for bxt and glk
drm/i915/execlists: Use rmb() to order CSB reads
drm/i915/userptr: reject zero user_size
Pull hwmon fixes from Guenter Roeck:
"Two k10temp fixes:
- fix race condition when accessing System Management Network
registers
- fix reading critical temperatures on F15h M60h and M70h
Also add PCI ID's for the AMD Raven Ridge root bridge"
* tag 'hwmon-for-linus-v4.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (k10temp) Use API function to access System Management Network
x86/amd_nb: Add support for Raven Ridge CPUs
hwmon: (k10temp) Fix reading critical temperature register
Move initialization of statistics buffers from ibmvnic_init function
into ibmvnic_probe. In the current state, ibmvnic_init will be called
again during a device reset, resulting in the allocation of new
buffers without freeing the old ones.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not necessary to disable interrupt lines here during a reset
to handle a non-fatal firmware error. Move that call within the code
block that handles the other cases that do require interrupts to be
disabled and re-enabled.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the firmware map fails for whatever reason, remember to free
up the memory after.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull s390 fixes from Martin Schwidefsky:
- a fix for the vfio ccw translation code
- update an incorrect email address in the MAINTAINERS file
- fix a division by zero oops in the cpum_sf code found by trinity
- two fixes for the error handling of the qdio code
- several spectre related patches to convert all left-over indirect
branches in the kernel to expoline branches
- update defconfigs to avoid warnings due to the netfilter Kconfig
changes
- avoid several compiler warnings in the kexec_file code for s390
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/qdio: don't release memory in qdio_setup_irq()
s390/qdio: fix access to uninitialized qdio_q fields
s390/cpum_sf: ensure sample frequency of perf event attributes is non-zero
s390: use expoline thunks in the BPF JIT
s390: extend expoline to BC instructions
s390: remove indirect branch from do_softirq_own_stack
s390: move spectre sysfs attribute code
s390/kernel: use expoline for indirect branches
s390/ftrace: use expoline for indirect branches
s390/lib: use expoline for indirect branches
s390/crc32-vx: use expoline for indirect branches
s390: move expoline assembler macros to a header
vfio: ccw: fix cleanup if cp_prefetch fails
s390/kexec_file: add declaration of purgatory related globals
s390: update defconfigs
MAINTAINERS: update s390 zcrypt maintainers email address
Commit 539d39eb27 ("bcache: fix wrong return value in bch_debug_init()")
returns the return value of debugfs_create_dir() to bcache_init(). When
CONFIG_DEBUG_FS=n, bch_debug_init() always returns 1 and makes
bcache_init() failedi.
This patch makes bch_debug_init() always returns 0 if CONFIG_DEBUG_FS=n,
so bcache can continue to work for the kernels which don't have debugfs
enanbled.
Changelog:
v4: Add Acked-by from Kent Overstreet.
v3: Use IS_ENABLED(CONFIG_DEBUG_FS) to replace #ifdef DEBUG_FS.
v2: Remove a warning information
v1: Initial version.
Fixes: Commit 539d39eb27 ("bcache: fix wrong return value in bch_debug_init()")
Cc: stable@vger.kernel.org
Signed-off-by: Coly Li <colyli@suse.de>
Reported-by: Massimo B. <massimo.b@gmx.net>
Reported-by: Kai Krakow <kai@kaishome.de>
Tested-by: Kai Krakow <kai@kaishome.de>
Acked-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Disabling pm runtime at probe is not sufficient to get BAM working
on remotely controller instances. pm_runtime_get_sync() would return
-EACCES in such cases.
So check if runtime pm is enabled before returning error from bam functions.
Fixes: 5b4a68952a ("dmaengine: qcom: bam_dma: disable runtime pm on remote controlled")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A single fix for a recent regression.
* 'vmwgfx-fixes-4.17' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Set dmabuf_size when vmw_dmabuf_init is successful
- core: Fix regression in dev node offsets (Haneen)
- vc4: Fix memory leak on driver close (Eric)
- dumb-buffers: Prevent overflow in DIV_ROUND_UP() (Dan)
Cc: Haneen Mohammed <hamohammed.sa@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
* tag 'drm-misc-fixes-2018-05-16' of git://anongit.freedesktop.org/drm/drm-misc:
drm/dumb-buffers: Integer overflow in drm_mode_create_ioctl()
drm/vc4: Fix leak of the file_priv that stored the perfmon.
drm: Match sysfs name in link removal to link creation
After commit b196d88aba ("tun: fix use after free for ptr_ring") we
need clean up tx ring during release(). But unfortunately, it tries to
do the cleanup blindly after socket were destroyed which will lead
another use-after-free. Fix this by doing the cleanup before dropping
the last reference of the socket in __tun_detach().
Reported-by: Andrei Vagin <avagin@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Fixes: b196d88aba ("tun: fix use after free for ptr_ring")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stress on qedi/qedr load unload lead to list_del corruption.
This is due to ll2 connection terminate freeing resources without
verifying that no more ll2 processing will occur.
This patch unregisters the ll2 status block before terminating
the connection to assure this race does not occur.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ll2 flows of flushing the txq/rxq need to be synchronized with the
regular fp processing. Caused list corruption during load/unload stress
tests.
Fixes: 0a7fb11c23 ("qed: Add Light L2 support")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver should free all pending isles once it gets a FLUSH cqe from FW.
Part of iSCSI out of order flow.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configuration settings for RBTX4927 were accidentally removed,
leading to a silently broken network interface.
Re-add the missing settings to fix this.
Fixes: 8eb97ff5a4 ("net: 8390: remove m32r specific bits")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was possible to delete only one half of an IPv6, which would leave
the second half still programmed and possibly in use. Instead of
checking for the unused bitmap, we need to check the unique bitmap, and
refuse any deletion that does not match that criteria. We also need to
move that check from bcm_sf2_cfp_rule_del_one() into its caller:
bcm_sf2_cfp_rule_del() otherwise we would not be able to delete second
halves anymore that would not pass the first test.
Fixes: ba0696c22e ("net: dsa: bcm_sf2: Add support for IPv6 CFP rules")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had several issues that would make the programming of IPv6 rules both
inconsistent and error prone:
- the chain ID that we would be asking the hardware to put in the
packet's Broadcom tag would be off by one, it would return one of the
two indexes, but not the one user-space specified
- when an user specified a particular location to insert a CFP rule at,
we would not be returning the same index, which would be confusing if
nothing else
- finally, like IPv4, it would be possible to overflow the last entry by
re-programming it
Fix this by swapping the usage of rule_index[0] and rule_index[1] where
relevant in order to return a consistent and correct user-space
experience.
Fixes: ba0696c22e ("net: dsa: bcm_sf2: Add support for IPv6 CFP rules")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we let the kernel pick up a rule location with RX_CLS_LOC_ANY, we
would be able to overwrite the last rules because of a number of issues.
The IPv4 code path would not be checking that rule_index is within
bounds, and it would also only be allowed to pick up rules from range
0..126 instead of the full 0..127 range. This would lead us to allow
overwriting the last rule when we let the kernel pick-up the location.
Fixes: 3306145866 ("net: dsa: bcm_sf2: Move IPv4 CFP processing to specific functions")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stub_probe() calls put_busid_priv() in an error path when device isn't
found in the busid_table. Fix it by making put_busid_priv() safe to be
called with null struct bus_id_priv pointer.
This problem happens when "usbip bind" is run without loading usbip_host
driver and then running modprobe. The first failed bind attempt unbinds
the device from the original driver and when usbip_host is modprobed,
stub_probe() runs and doesn't find the device in its busid table and calls
put_busid_priv(0 with null bus_id_priv pointer.
usbip-host 3-10.2: 3-10.2 is not in match_busid table... skip!
[ 367.359679] =====================================
[ 367.359681] WARNING: bad unlock balance detected!
[ 367.359683] 4.17.0-rc4+ #5 Not tainted
[ 367.359685] -------------------------------------
[ 367.359688] modprobe/2768 is trying to release lock (
[ 367.359689]
==================================================================
[ 367.359696] BUG: KASAN: null-ptr-deref in print_unlock_imbalance_bug+0x99/0x110
[ 367.359699] Read of size 8 at addr 0000000000000058 by task modprobe/2768
[ 367.359705] CPU: 4 PID: 2768 Comm: modprobe Not tainted 4.17.0-rc4+ #5
Fixes: 22076557b0 ("usbip: usbip_host: fix NULL-ptr deref and use-after-free errors") in usb-linus
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The micrel KSZ9031 phy has a optional clock pin (CLK125_NDO) which can be
used as reference clock for the MAC unit. The clock signal must meet the
RGMII requirements to ensure the correct data transmission between the
MAC and the PHY. The KSZ9031 phy does not fulfill the duty cycle
requirement if the phy is configured as slave. For a complete
describtion look at the errata sheets: DS80000691D or DS80000692D.
The errata sheet recommends to force the phy into master mode whenever
there is a 1000Base-T link-up as work around. Only set the
"micrel,force-master" property if you use the phy reference clock provided
by CLK125_NDO pin as MAC reference clock in your application.
Attenation, this workaround is only usable if the link partner can
be configured to slave mode for 1000Base-T.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
[m.felsch@pengutronix.de: fix dt-binding documentation]
[m.felsch@pengutronix.de: use already existing result var for read/write]
[m.felsch@pengutronix.de: add error handling]
[m.felsch@pengutronix.de: add more comments]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When master device's mac has been changed, the commit
32c10bbfe9 ("ipvlan: always use the current L2 addr of the
master") makes the IPVlan devices's mac changed also, but it
doesn't do related works such as flush the IPVlan devices's
arp table.
Signed-off-by: Keefe Liu <liuqifa@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a comment here which says that DIV_ROUND_UP() and that's where
the problem comes from. Say you pick:
args->bpp = UINT_MAX - 7;
args->width = 4;
args->height = 1;
The integer overflow in DIV_ROUND_UP() means "cpp" is UINT_MAX / 8 and
because of how we picked args->width that means cpp < UINT_MAX / 4.
I've fixed it by preventing the integer overflow in DIV_ROUND_UP(). I
removed the check for !cpp because it's not possible after this change.
I also changed all the 0xffffffffU references to U32_MAX.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180516140026.GA19340@mwanda
