commit 443772d408 upstream.
If function tracing is enabled for some of the low-level suspend/resume
functions, it leads to triple fault during resume from suspend, ultimately
ending up in a reboot instead of a resume (or a total refusal to come out
of suspended state, on some machines).
This issue was explained in more detail in commit f42ac38c59 (ftrace:
disable tracing for suspend to ram). However, the changes made by that commit
got reverted by commit cbe2f5a6e8 (tracing: allow tracing of
suspend/resume & hibernation code again). So, unfortunately since things are
not yet robust enough to allow tracing of low-level suspend/resume functions,
suspend/resume is still broken when ftrace is enabled.
So fix this by disabling function tracing during suspend/resume & hibernation.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05b4877f6a upstream.
If create_basic_memory_bitmaps() fails, usermodehelpers are not re-enabled
before returning. Fix this. And while at it, reword the goto labels so that
they look more meaningful.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During some CPU power modes entered during idle, hotplug and
suspend, peripherals located in the CPU power domain, such as
the GIC, localtimers, and VFP, may be powered down. Add a
notifier chain that allows drivers for those peripherals to
be notified before and after they may be reset.
Notified drivers can include VFP co-processor, interrupt controller
and it's PM extensions, local CPU timers context save/restore which
shouldn't be interrupted. Hence CPU PM event APIs must be called
with interrupts disabled.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-and-Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Conflicts:
kernel/power/Kconfig
port from msm:
This fixes the issue where LCD takes a long time to come back up
since the execution of backlight on and late_resume works by the
suspend worker thread is delayed due to one (or more) of the
sys_sync calls in early_suspend and suspend paths taking a long
time (sometimes 15sec or more) for the below reported scenario(s):
Scenario 1 (copy with usb connected):
1. plug usb
2. adb shell
3. busybox cp /sdcard/file1 /sdcard/file2 (copy >= 100MB file1
in sdcard/emmc to file2 in sdcard/emmc)
4. press end key to suspend
5. press end key again and it takes a long time for LCD to come
back up
Scenario 2 (background copy):
1. plug usb
2. adb shell
3. busybox cp /sdcard/file1 /sdcard/file2 & (copy >= 100MB file1
in sdcard/emmc to file2 in sdcard/emmc)
4. disconnect usb
5. press end key to suspend
6. press end key again and it takes a long time for LCD to come
back up
A more common form of Scenario 2 is for the user to just use the
copy function on the UI to copy large file(s).
We address this by moving sys_sync calls to a separate workqueue
and having a timeout polling based mechanism to bail out of suspend
in case of user invoking a wakeup event (like end key press) while
we are waiting for the sys_sync completion at the synchronization
point in suspend worker thread context.
commit 528f7ce6e4 upstream.
In enter_state() we use "state" as an offset for the pm_states[]
array. The pm_states[] array only has PM_SUSPEND_MAX elements so
this test is off by one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use DEBUG_WAKEUP flag to show wakelocks that abort suspend, in
addition to showing wakelocks held during system resume.
DEBUG_WAKEUP is enabled by default.
Change-Id: If6fa68e8afbc482a5300ffab2964694b02b34f41
Signed-off-by: Todd Poynor <toddpoynor@google.com>
If the wakelock driver aborts suspend due to an already-held
wakelock, don't report the next wakelock held as the "wake up
wakelock".
Change-Id: I582ffbb87a3c361739a77d839a0c62921cff11a6
Signed-off-by: Todd Poynor <toddpoynor@google.com>
when enabled, prints out the function of each handler as they are called
Change-Id: I5ed251867e0e3aa3cd05f030ff3579808cedd0c2
Signed-off-by: Erik Gilling <konkers@android.com>
Prints the time spent in suspend in the kernel log, and
keeps statistics on the time spent in suspend in
/sys/kernel/debug/suspend_time
Change-Id: Ia6b9ebe4baa0f7f5cd211c6a4f7e813aefd3fa1d
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Todd Poynor <toddpoynor@google.com>
There is a bug in free_unnecessary_pages() that causes it to
attempt to free too many pages in some cases, which triggers the
BUG_ON() in memory_bm_clear_bit() for copy_bm. Namely, if
count_data_pages() is initially greater than alloc_normal, we get
to_free_normal equal to 0 and "save" greater from 0. In that case,
if the sum of "save" and count_highmem_pages() is greater than
alloc_highmem, we subtract a positive number from to_free_normal.
Hence, since to_free_normal was 0 before the subtraction and is
an unsigned int, the result is converted to a huge positive number
that is used as the number of pages to free.
Fix this bug by checking if to_free_normal is actually greater
than or equal to the number we're going to subtract from it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@kernel.org
When opening /dev/snapshot device, snapshot_open() creates memory
bitmaps which are freed in snapshot_release(). But if any of the
callbacks called by pm_notifier_call_chain() returns NOTIFY_BAD, open()
fails, snapshot_release() is never called and bitmaps are not freed.
Next attempt to open /dev/snapshot then triggers BUG_ON() check in
create_basic_memory_bitmaps(). This happens e.g. when vmwatchdog module
is active on s390x.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
When DEBUG_SUSPEND is enabled print active wakelocks when we check
if there are any active wakelocks.
In print_active_locks(), print expired wakelocks if DEBUG_EXPIRE is enabled
Change-Id: Ib1cb795555e71ff23143a2bac7c8a58cbce16547
Signed-off-by: Mike Chan <mike@android.com>
Rather than signaling a full update of the display from userspace via a
console switch, this patch introduces 2 files int /sys/power,
wait_for_fb_sleep and wait_for_fb_wake. Reading these files will block
until the requested state has been entered. When a read from
wait_for_fb_sleep returns userspace should stop drawing. When
wait_for_fb_wake returns, it should do a full update. If either are called
when the fb driver is already in the requested state, they will return
immediately.
Signed-off-by: Rebecca Schultz <rschultz@google.com>
Signed-off-by: Arve Hjønnevåg <arve@android.com>
This adds /sys/power/wake_lock and /sys/power/wake_unlock.
Writing a string to wake_lock creates a wake lock the
first time is sees a string and locks it. Optionally, the
string can be followed by a timeout.
To unlock the wake lock, write the same string to wake_unlock.
Change-Id: I66c6e3fe6487d17f9c2fafde1174042e57d15cd7
If EARLYSUSPEND is enabled then writes to /sys/power/state no longer
blocks, and the kernel will try to enter the requested state every
time no wakelocks are held. Write "on" to resume normal operation.
PM: wakelock: Replace expire work with a timer
The expire work function did not work in the normal case.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Some of the kerneldoc comments in kernel/power/hibernate.c are
outdated and some of them don't adhere to the kernel's standards.
Update them and make them look in a consistent way.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
All architectures supporting hibernation define
arch_prepare_suspend() as an empty function, so remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Some comments in the core hibernate code are outdated, some aren't
necessary any more and at least one of them is plain wrong. Remove
those comments or update them.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If device drivers allocate substantial amounts of memory (above 1 MB)
in their hibernate .freeze() callbacks (or in their legacy suspend
callbcks during hibernation), the subsequent creation of hibernate
image may fail due to the lack of memory. This is the case, because
the drivers' .freeze() callbacks are executed after the hibernate
memory preallocation has been carried out and the preallocated amount
of memory may be too small to cover the new driver allocations.
Unfortunately, the drivers' .prepare() callbacks also are executed
after the hibernate memory preallocation has completed, so they are
not suitable for allocating additional memory either. Thus the only
way a driver can safely allocate memory during hibernation is to use
a hibernate/suspend notifier. However, the notifiers are called
before the freezing of user space and the drivers wanting to use them
for allocating additional memory may not know how much memory needs
to be allocated at that point.
To let device drivers overcome this difficulty rework the hibernation
sequence so that the memory preallocation is carried out after the
drivers' .prepare() callbacks have been executed, so that the
.prepare() callbacks can be used for allocating additional memory
to be used by the drivers' .freeze() callbacks. Update documentation
to match the new behavior of the code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Now that we have CONFIG_DYNAMIC_DEBUG there is no need for yet
another flag causing dev_dbg() and pr_debug() statements in the
core PM code to produce output. Moreover, CONFIG_PM_VERBOSE
causes so much output to be generated that it's not really useful
and almost no one sets it.
References: https://bugzilla.kernel.org/show_bug.cgi?id=23182
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* power-domains:
PM: Fix build issue in clock_ops.c for CONFIG_PM_RUNTIME unset
PM: Revert "driver core: platform_bus: allow runtime override of dev_pm_ops"
OMAP1 / PM: Use generic clock manipulation routines for runtime PM
PM / Runtime: Generic clock manipulation rountines for runtime PM (v6)
PM / Runtime: Add subsystem data field to struct dev_pm_info
OMAP2+ / PM: move runtime PM implementation to use device power domains
PM / Platform: Use generic runtime PM callbacks directly
shmobile: Use power domains for platform runtime PM
PM: Export platform bus type's default PM callbacks
PM: Make power domain callbacks take precedence over subsystem ones
* syscore:
PM: Remove sysdev suspend, resume and shutdown operations
PM / PowerPC: Use struct syscore_ops instead of sysdevs for PM
PM / UNICORE32: Use struct syscore_ops instead of sysdevs for PM
PM / AVR32: Use struct syscore_ops instead of sysdevs for PM
PM / Blackfin: Use struct syscore_ops instead of sysdevs for PM
ARM / Samsung: Use struct syscore_ops for "core" power management
ARM / PXA: Use struct syscore_ops for "core" power management
ARM / SA1100: Use struct syscore_ops for "core" power management
ARM / Integrator: Use struct syscore_ops for core PM
ARM / OMAP: Use struct syscore_ops for "core" power management
ARM: Use struct syscore_ops instead of sysdevs for PM in common code
This reverts commit bea3864fb6
(PM / Hibernate: Reduce autotuned default image size), because users
are now able to resolve the issue this commit was supposed to address
in a different way (i.e. by using the new /sys/power/reserved_size
interface).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Martin reports that on his system hibernation occasionally fails due
to the lack of memory, because the radeon driver apparently allocates
too much of it during the device freeze stage. It turns out that the
amount of memory allocated by radeon during hibernation (and
presumably during system suspend too) depends on the utilization of
the GPU (e.g. hibernating while there are two KDE 4 sessions with
compositing enabled causes radeon to allocate more memory than for
one KDE 4 session).
In principle it should be possible to use image_size to make the
memory preallocation mechanism free enough memory for the radeon
driver, but in practice it is not easy to guess the right value
because of the way the preallocation code uses image_size. For this
reason, it seems reasonable to allow users to control the amount of
memory reserved for driver allocations made after the hibernate
preallocation, which currently is constant and amounts to 1 MB.
Introduce a new sysfs file, /sys/power/reserved_size, whose value
will be used as the amount of memory to reserve for the
post-preallocation reservations made by device drivers, in bytes.
For backwards compatibility, set its default (and initial) value to
the currently used number (1 MB).
References: https://bugzilla.kernel.org/show_bug.cgi?id=34102
Reported-and-tested-by: Martin Steigerwald <Martin@Lichtvoll.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The current implementation of suspend-to-RAM returns 0 if there is an
error from suspend_enter(), because suspend_devices_and_enter() ignores
the return value from suspend_enter(). This patch addresses this issue
and properly keep the error return from suspend_enter() and let
suspend_devices_and_enter relay the error return.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since suspend, resume and shutdown operations in struct sysdev_class
and struct sysdev_driver are not used any more, remove them. Also
drop sysdev_suspend(), sysdev_resume() and sysdev_shutdown() used
for executing those operations and modify all of their users
accordingly. This reduces kernel code size quite a bit and reduces
its complexity.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
