struct tcp_fastopen_context has a field named tfm, which is a pointer
to a crypto_cipher structure.
It currently has a __rcu annotation, which is not needed at all.
tcp_fastopen_ctx is the pointer fetched by rcu_dereference(), but once
we have a pointer to current tcp_fastopen_context, we do not use/need
rcu_dereference() to access tfm.
This fixes a lot of sparse errors like the following :
net/ipv4/tcp_fastopen.c:21:31: warning: incorrect type in argument 1 (different address spaces)
net/ipv4/tcp_fastopen.c:21:31: expected struct crypto_cipher *tfm
net/ipv4/tcp_fastopen.c:21:31: got struct crypto_cipher [noderef] <asn:4>*tfm
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADAU1701 has 12 pins that can be configured depending on the system
configuration. Allow settting the corresponding registers from DT.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The hardware I/O has to be open-coded due to registers of unequal sizes.
Other than that, the transition is straight forward.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ADAU1701 has 2 hardware pins to configure the PLL mode in accordance
to the MCLK-to-LRCLK ratio. These pins have to be stable before the chip
is released from reset, and a full reset cycle, including a new firmware
download is needed whenever they change.
This patch adds GPIO properties to the DT bindings of the Codec, and
implements makes the set_sysclk memorize the configured sysclk.
Because the run-time parameters are unknown at probe time, the first
firmware download is postponed to the first hw_params call, when the
driver can determine the mclk/lrclk divider. Subsequent downloads
are only issued when the divider configuration changes.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The chip needs a new download after each reset, so the code to do that
needs to live in adau1701_reset().
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The TAS5086 has two alternative modes to start its PWM channels, Mid-Z
and Low-Z. Which one to use depends on how the PWM power stages are
connected to the TAS5086.
This patch adds 6 optional boolean properties to the DT bindings of the
driver which allow the user to configure each individual channel to the
Mid-Z scheme, and leaves all the others to the default (Low-Z).
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The TAS5086 has two muxes, one for connecting I2S inputs to internal
channels, and another one for selecting which internal channel should
be routed to which PWM output pin.
This patch adds DAPM widgets and routes for this driver.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add register definitions for input and output mux registers, and rewrite
the tas5086_accessible_reg() function.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to support registers of unequal sizes, the I2C I/O has to be
open-coded.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As some of ALC269 quirks use the inverted dmic feature, we need to
call alc_inv_dmic_sync() in the resume callback like in alc_resume(),
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The stac_resume() is exactly what the default resume code does, so
we don't have to define and use it doubly. Let's cut it off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To replace down() with down_interrutible() to avoid following
warning:
[c00000007ba7b710] [c000000000014410] .__switch_to+0x1b0/0x380
[c00000007ba7b7c0] [c0000000007b408c] .__schedule+0x3ec/0x970
[c00000007ba7ba50] [c0000000007b1f24] .schedule_timeout+0x1a4/0x2b0
[c00000007ba7bb30] [c0000000007b34a4] .__down+0xa4/0x104
[c00000007ba7bbf0] [c0000000000b9230] .down+0x60/0x70
[c00000007ba7bc80] [c0000000000336d0] .eeh_event_handler+0x70/0x190
[c00000007ba7bd30] [c0000000000b1a58] .kthread+0xe8/0xf0
[c00000007ba7be30] [c00000000000a05c] .ret_from_kernel_thread+0x5c/0x8
This also avoids keeping the load average up while doing nothing.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Originally, eeh_mutex was introduced to protect the PE hierarchy
tree and the attached EEH devices because EEH core was possiblly
running with multiple threads to access the PE hierarchy tree.
However, we now have only one kthread in EEH core. So we needn't
the eeh_mutex and just remove it.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Building with CONFIG_TRANSPARENT_HUGEPAGE disabled causes the following
build wearnings;
powerpc/arch/powerpc/include/asm/mmu-hash64.h: In function ‘__hash_page_thp’:
powerpc/arch/powerpc/include/asm/mmu-hash64.h:354: warning: no return statement in function returning non-void
This patch adds a return -1 to the static inline for __hash_page_thp()
to correct the warnings.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since now we have pstore support for nvram in pseries, enable it
in the default config. With this config option enabled, pstore
infra-structure will be used to read/write the messages from/to nvram.
Signed-off-by: Aruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In 9422de3 "powerpc: Hardware breakpoints rewrite to handle non DABR breakpoint
registers" we changed the way we mark extraneous irqs with this:
- info->extraneous_interrupt = !((bp->attr.bp_addr <= dar) &&
- (dar - bp->attr.bp_addr < bp->attr.bp_len));
+ if (!((bp->attr.bp_addr <= dar) &&
+ (dar - bp->attr.bp_addr < bp->attr.bp_len)))
+ info->type |= HW_BRK_TYPE_EXTRANEOUS_IRQ;
Unfortunately this is bogus as it never clears extraneous IRQ if it's already
set.
This correctly clears extraneous IRQ before possibly setting it.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reported-by: Edjunior Barbosa Machado <emachado@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The smallest match region for both the DABR and DAWR is 8 bytes, so the
kernel needs to filter matches when users want to look at regions smaller than
this.
Currently we set the length of PPC_BREAKPOINT_MODE_EXACT breakpoints to 8.
This is wrong as in exact mode we should only match on 1 address, hence the
length should be 1.
This ensures that the kernel will filter out any exact mode hardware breakpoint
matches on any addresses other than the requested one.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reported-by: Edjunior Barbosa Machado <emachado@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Hdmi driver may not receive intrinsic event from gfx side when
it's in runtime suspend mode. There's no ELD info when exit from
runtime suspend. This patch avoid missing ELD info.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch does not change the content, it merely re-orders
configuration items and drops explicit options which already
apply as the default.
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Pull spi updates from Mark Brown:
"A few last minute SPI updates: fix a missized allocation and use
atomic allocations in atomic context in the PXA driver, and fix the
checking of return codes in the S3C64xx driver which caused spurious
errors under heavy load."
* tag 'spi-v3.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi/pxa2xx: fix memory corruption due to wrong size used in devm_kzalloc()
spi/pxa2xx: use GFP_ATOMIC in sg table allocation
spi: s3c64xx: Fix pm_runtime_get_sync() return value check
This patch is a cleanup to the previous patch "reset hda link during system/
runtime suspend".
In this patch
- azx_enter_link_reset() and azx_exit_link_reset() are defined for entering and
exiting the link reset respectively. azx_link_reset() is no longer used and
replaced by azx_enter_link_reset().
- azx_reset() reuses the above two new functions for a link reset cycle
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pin's connection list may change dynamically with hot-plug event
on Intel Haswell chip. Users would see connections be "0" in codec#.
when play audio on this pin, software driver choose converter from cache
connections. So add "In-driver connection" info to avoid confuse when
raw connections are different with cache connection.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got bug report wrt many machines with VT1708 (e.g. IBM POS
machines) showing the broken auto-mute behavior. It turned out that
the problem is that the pin control values of the speaker and line-out
pins are completely ignored. As a workaround, let's use the newly
introduced feature of the generic parser, to control the mute via amp
on pins.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new flag, auto_mute_via_amp, to determine the behavior of the
headphone / line-out auto-mute. When this flag is set, the generic
driver mutes the speaker and line outputs via the amp mute of each
pin, instead of changing the pin control values.
This is introduced for devices that don't work expectedly with the pin
control values; for example, some devices are known to keep enabling
the speaker outputs no matter which pin control values are set on the
speaker pins.
The driver doesn't check actually whether the pins have the output amp
caps, but assumes that the proper mixer (mute) controls are created on
all these pins. If not the case, you can't use this flag for your
device.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch refactors ISCSI_OP_TEXT handling within iscsi-target in
order to handle iscsi_text payloads in a transport specific manner.
This includes splitting current iscsit_handle_text_cmd() into
iscsit_setup_text_cmd() and iscsit_process_text_cmd() calls, and
makes iscsit_handle_text_cmd be only used internally by traditional
iscsi socket calls.
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch refactors ISCSI_OP_NOOP handling within iscsi-target in
order to handle iscsi_nopout payloads in a transport specific manner.
This includes splitting existing iscsit_handle_nop_out() into
iscsit_setup_nop_out() and iscsit_process_nop_out() calls, and
makes iscsit_handle_nop_out() be only used internally by traditional
iscsi socket calls.
Next update iser-target code to use new callers and add FIXME for
the handling iscsi_nopout payloads. Also fix reject response handling
in iscsit_setup_nop_out() to use proper iscsit_add_reject_from_cmd().
v2: Fix uninitialized iscsit_handle_nop_out() payload_length usage (Fengguang)
v3: Remove left-over dead code in iscsit_setup_nop_out() (DanC)
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Drivers are allowed (actually have to) disable unrelated crtcs in
their ->set_config callback (when we steal all the connectors from
that crtc). If they do that they'll clear crtc->fb to NULL.
Which results in a refcount leak, since the drm core is keeping track
of that reference.
To fix this track the old fb of all crtcs and adjust references for
all of them. Of course, since we only hold an additional reference for
the fb for the current crtc we need to increase refcounts before we
drop the old one.
This approach has the benefit that it inches us a bit closer to an
atomic modeset world, where we want to update the config of all crtcs
in one step.
This regression has been introduce in the framebuffer refcount
conversion, specifically in
commit b0d1232589
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Dec 11 01:07:12 2012 +0100
drm: refcounting for crtc framebuffers
Reported-by: Russell King <linux@arm.linux.org.uk>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Historically drm lacked fb refcounting, so the updating of crtc->fb
was done by the lower levels at a point convenient to get their own
refcounting (e.g. refcounts for the underlying gem bo, pinning
refcounts) right. With the introduction of refcounted fbs the drm core
handled the fb refcounts, but still relied on drivers to update the
crtc->fb pointer (this approach required the least invasive changes in
drivers).
Enforce this contract with a WARN_ON.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Atm the crtc helper implementation of set_config has really
inconsisten semantics: If just an fb update is good enough, dpms state
will be left as-is, but if we do a full modeset we force everything to
dpms on.
This change has already been applied to the i915 modeset code in
commit e3de42b684
Author: Imre Deak <imre.deak@intel.com>
Date: Fri May 3 19:44:07 2013 +0200
drm/i915: force full modeset if the connector is in DPMS OFF mode
which according to Greg KH seems to aim for a new record in most
Bugzilla: links in a commit message.
The history of this dpms forcing is pretty interesting. This patch
here is an almost-revert of
commit 811aaa55ba
Author: Keith Packard <keithp@keithp.com>
Date: Thu Feb 3 16:57:28 2011 -0800
drm: Only set DPMS ON when actually configuring a mode
which fixed the bug of trying to dpms on disabled outputs, but
introduced the new discrepancy between an fb update only and full
modesets. The actual introduction of this goes back to
commit bf9dc102e2
Author: Keith Packard <keithp@keithp.com>
Date: Fri Nov 26 10:45:58 2010 -0800
drm: Set connector DPMS status to ON in drm_crtc_helper_set_config
And if you'd dig around in the i915 driver code there's even more fun
around forcing dpms on and losing our heads and temper of the
resulting inconsistencies. Especially the DP re-training code had tons
of funny stuff in it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
... since we already check for fb->pixel_format, which encodes all
this. The other two fields are only for backwards compat of older
drivers (and we might want to look into eventually just killing them).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's no point in trying to clean up after driver-bugs, so just blow
up. Furthermore it's an interface abuse to set no mode but have an fb
and aslo to try to set an fb without enough connectors. These two
spefici cases of interface abuse have been committed by the fb helper,
but that's been fixed meanwhile in
commit 7e53f3a423
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Jan 21 10:52:17 2013 +0100
drm/fb-helper: fixup set_config semantics
The i915 driver has been shipping since a while with these BUGs with
no reports, so should be save.
Note that this drops an ugly case where we clear crtc->fb behind the
upper levels back and so cause a refcounting mayhem, which Russell
Kins spotted while trying to hunt down a drm framebuffer leak.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The Interlaken is a narrow, high speed channelized chip-to-chip interface. To
facilitate interoperability between a data path device and a look-aside
co-processor, the Interlaken Look-Aside protocol is defined for short
transaction-related transfers. Although based on the Interlaken protocol,
Interlaken Look-Aside is not directly compatible with Interlaken and can be
considered a different operation mode.
The Interlaken LA controller connects internal platform to Interlaken serial
interface. It accepts LA command through software portals, which are system
memory mapped 4KB spaces. The LA commands are then translated into the
Interlaken control words and data words, which are sent on TX side to TCAM
through SerDes lanes.
Signed-off-by: Joe Liccese <joe.liccese@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add support to differentiate between iMR(no external memory) and MR(with
external memory) controllers.
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
MegaRAID older Firmware does not support uneven span configuration for PRL11.
E.g User wants to create 34 Driver PRL11 config, it was not possible using old
firmware, since it was not supported configuration in old firmware
Old Firmware expect even number of Drives in each span and same number of
physical drives at each span. Considering above design, 17 Drives at Span-0
and 17 drives at span-1 was not possible.
Now, using this new feature Firmware and Driver both required changes. New
Firmware can allow user to create 16 Drives at span-0 and 18 Drives at
span-1. This will allow user to create 34 Drives Uneven span PRL11.
RAID map is interface between Driver and FW to fetch all required
fields(attributes) for each Virtual Drives. Since legacy RAID map consider
Even Span design, there was no place to keep Uneven span information in
existing Raid map. Because of this limitation, for Uneven span VD, driver can
not use RAID map.
This patch address the changes required in Driver to support Uneven span PRL11
support.
1. Driver will find if Firmware has UnevenSpanSupport or not by reading
Controller Info.
2. If Firmware has UnvenSpan PRL11 support, then Driver will inform about its
capability of handling UnevenSpan PRL11 to the firmware.
3. Driver will update its copy of span info on each time Raid map update is
called.
4. Follow different IO path if it is Uneven Span. (For Uneven Span, Driver
uses Span Set info to find relavent fields for that particular Virtual
Disk)
More verbose prints will be available by setting "SPAN_DEBUG" to 1 at
compilation time.
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This Driver will use more than 8 MSI-x support provided by Invader/Fury max
upto 128 MSI-x.
[jejb: fix checkpatch warning]
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Git commit 90797e6d1e
("drm/i915: create compact dma scatter lists for gem objects") makes
certain assumptions about the under laying DMA API that are not always
correct.
On a ThinkPad X230 with an Intel HD 4000 with Xen during the bootup
I see:
[drm:intel_pipe_set_base] *ERROR* pin & fence failed
[drm:intel_crtc_set_config] *ERROR* failed to set mode on [CRTC:3], err = -28
Bit of debugging traced it down to dma_map_sg failing (in
i915_gem_gtt_prepare_object) as some of the SG entries were huge (3MB).
That unfortunately are sizes that the SWIOTLB is incapable of handling -
the maximum it can handle is a an entry of 512KB of virtual contiguous
memory for its bounce buffer. (See IO_TLB_SEGSIZE).
Previous to the above mention git commit the SG entries were of 4KB, and
the code introduced by above git commit squashed the CPU contiguous PFNs
in one big virtual address provided to DMA API.
This patch is a simple semi-revert - were we emulate the old behavior
if we detect that SWIOTLB is online. If it is not online then we continue
on with the new compact scatter gather mechanism.
An alternative solution would be for the the '.get_pages' and the
i915_gem_gtt_prepare_object to retry with smaller max gap of the
amount of PFNs that can be combined together - but with this issue
discovered during rc7 that might be too risky.
Reported-and-Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Imre Deak <imre.deak@intel.com>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
CC: David Airlie <airlied@linux.ie>
CC: <dri-devel@lists.freedesktop.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
One remaining regression fix for i915. I've left it in -fixes for more
than a week since it's in tricky code, and it took us a few kernel
releases to notice the regression at all. The fence leak is especially
annoying on gen2/3 and will kill userspace there quickly. For extra
paranoia we've added a WARN in -next to catch this, things seem to be
solid now.
* tag 'drm-intel-fixes-2013-06-24' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Restore fences after resume and GPU resets
Free event detail memory from more common place, instead of doing it for
limited device types.
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
