[ Upstream commit 50caa777a3 ]
Fix the missing clk_disable_unprepare() before return
from emac_clks_phase1_init() in the error handling case.
Fixes: b9b17debc6 ("net: emac: emac gigabit ethernet controller driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 592d751c1e upstream.
If we don't have a hardware multicast filter available then instead of
silently failing to listen for the requested ethernet broadcast
addresses fall back to receiving all multicast packets, in a similar
fashion to other drivers with no multicast filter.
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df43dd526e upstream.
The IPQ806x does not appear to have a functional multicast ethernet
address filter. This was observed as a failure to correctly receive IPv6
packets on a LAN to the all stations address. Checking the vendor driver
shows that it does not attempt to enable the multicast filter and
instead falls back to receiving all multicast packets, internally
setting ALLMULTI.
Use the new fallback support in the dwmac1000 driver to correctly
achieve the same with the mainline IPQ806x driver. Confirmed to fix IPv6
functionality on an RB3011 router.
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c7ca03c216 ]
1. Added a skb->len check
This driver expects upper layers to include a pseudo header of 1 byte
when passing down a skb for transmission. This driver will read this
1-byte header. This patch added a skb->len check before reading the
header to make sure the header exists.
2. Changed to use needed_headroom instead of hard_header_len to request
necessary headroom to be allocated
In net/packet/af_packet.c, the function packet_snd first reserves a
headroom of length (dev->hard_header_len + dev->needed_headroom).
Then if the socket is a SOCK_DGRAM socket, it calls dev_hard_header,
which calls dev->header_ops->create, to create the link layer header.
If the socket is a SOCK_RAW socket, it "un-reserves" a headroom of
length (dev->hard_header_len), and assumes the user to provide the
appropriate link layer header.
So according to the logic of af_packet.c, dev->hard_header_len should
be the length of the header that would be created by
dev->header_ops->create.
However, this driver doesn't provide dev->header_ops, so logically
dev->hard_header_len should be 0.
So we should use dev->needed_headroom instead of dev->hard_header_len
to request necessary headroom to be allocated.
This change fixes kernel panic when this driver is used with AF_PACKET
SOCK_RAW sockets.
Call stack when panic:
[ 168.399197] skbuff: skb_under_panic: text:ffffffff819d95fb len:20
put:14 head:ffff8882704c0a00 data:ffff8882704c09fd tail:0x11 end:0xc0
dev:veth0
...
[ 168.399255] Call Trace:
[ 168.399259] skb_push.cold+0x14/0x24
[ 168.399262] eth_header+0x2b/0xc0
[ 168.399267] lapbeth_data_transmit+0x9a/0xb0 [lapbether]
[ 168.399275] lapb_data_transmit+0x22/0x2c [lapb]
[ 168.399277] lapb_transmit_buffer+0x71/0xb0 [lapb]
[ 168.399279] lapb_kick+0xe3/0x1c0 [lapb]
[ 168.399281] lapb_data_request+0x76/0xc0 [lapb]
[ 168.399283] lapbeth_xmit+0x56/0x90 [lapbether]
[ 168.399286] dev_hard_start_xmit+0x91/0x1f0
[ 168.399289] ? irq_init_percpu_irqstack+0xc0/0x100
[ 168.399291] __dev_queue_xmit+0x721/0x8e0
[ 168.399295] ? packet_parse_headers.isra.0+0xd2/0x110
[ 168.399297] dev_queue_xmit+0x10/0x20
[ 168.399298] packet_sendmsg+0xbf0/0x19b0
......
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3207f715c3 ]
Fix memory allocation for ethernet address hash table.
The code was wrongly allocating an array for eth hash table which
is incorrect because this is the main structure for eth hash table
(struct eth_hash_t) that contains inside a number of elements.
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc79fd8f55 ]
The parameter 'priority' is incorrectly forced to zero which ultimately
induces logically dead code in the subsequent lines.
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99f47abd9f ]
Potentially overflowing expression (ts_freq << 16 and intgr << 16)
declared as type u32 (32-bit unsigned) is evaluated using 32-bit
arithmetic and then used in a context that expects an expression of
type u64 (64-bit unsigned) which ultimately is used as 16-bit
unsigned by typecasting to u16. Fixed by using an unsigned 32-bit
integer since the value is truncated anyway in the end.
Fixes: 414fd46e77 ("fsl/fman: Add FMan support")
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36f28f7687 ]
Update the size used in 'dma_free_coherent()' in order to match the one
used in the corresponding 'dma_alloc_coherent()', in
'spider_net_init_chain()'.
Fixes: d4ed8f8d1f ("Spidernet DMA coalescing")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9018fd7f2a ]
On failure pcie_capability_read_dword() sets it's last parameter, val
to 0. However, with Patch 14/14, it is possible that val is set to ~0 on
failure. This would introduce a bug because (x & x) == (~0 & x).
This bug can be avoided without changing the function's behaviour if the
return value of pcie_capability_read_dword is checked to confirm success.
Check the return value of pcie_capability_read_dword() to ensure success.
Suggested-by: Bjorn Helgaas <bjorn@helgaas.com>
Signed-off-by: Bolarinwa Olayemi Saheed <refactormyself@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200713175529.29715-3-refactormyself@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0dced17ad ]
This reverts commit 71130f2997.
In commit 71130f2997 ("vxlan: fix tos value before xmit") we want to
make sure the tos value are filtered by RT_TOS() based on RFC1349.
0 1 2 3 4 5 6 7
+-----+-----+-----+-----+-----+-----+-----+-----+
| PRECEDENCE | TOS | MBZ |
+-----+-----+-----+-----+-----+-----+-----+-----+
But RFC1349 has been obsoleted by RFC2474. The new DSCP field defined like
0 1 2 3 4 5 6 7
+-----+-----+-----+-----+-----+-----+-----+-----+
| DS FIELD, DSCP | ECN FIELD |
+-----+-----+-----+-----+-----+-----+-----+-----+
So with
IPTOS_TOS_MASK 0x1E
RT_TOS(tos) ((tos)&IPTOS_TOS_MASK)
the first 3 bits DSCP info will get lost.
To take all the DSCP info in xmit, we should revert the patch and just push
all tos bits to ip_tunnel_ecn_encap(), which will handling ECN field later.
Fixes: 71130f2997 ("vxlan: fix tos value before xmit")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ea060b3526 ]
Drop the bogus endpoint-lookup helper which could end up accepting
interfaces based on endpoints belonging to unrelated altsettings.
Note that the returned bulk pipes and interrupt endpoint descriptor
were never actually used. Instead the bulk-endpoint numbers are
hardcoded to 1 and 2 (matching the specification), while the interrupt-
endpoint descriptor was assumed to be the third descriptor created by
USB core.
Try to bring some order to this by dropping the bogus lookup helper and
adding the missing endpoint sanity checks while keeping the interrupt-
descriptor assumption for now.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b5141915b5 ]
The commit cited below removed the RCU read-side critical section from
rtnl_fdb_dump() which means that the ndo_fdb_dump() callback is invoked
without RCU protection.
This results in the following warning [1] in the VXLAN driver, which
relied on the callback being invoked from an RCU read-side critical
section.
Fix this by calling rcu_read_lock() in the VXLAN driver, as already done
in the bridge driver.
[1]
WARNING: suspicious RCU usage
5.8.0-rc4-custom-01521-g481007553ce6 #29 Not tainted
-----------------------------
drivers/net/vxlan.c:1379 RCU-list traversed in non-reader section!!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by bridge/166:
#0: ffffffff85a27850 (rtnl_mutex){+.+.}-{3:3}, at: netlink_dump+0xea/0x1090
stack backtrace:
CPU: 1 PID: 166 Comm: bridge Not tainted 5.8.0-rc4-custom-01521-g481007553ce6 #29
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-2.fc32 04/01/2014
Call Trace:
dump_stack+0x100/0x184
lockdep_rcu_suspicious+0x153/0x15d
vxlan_fdb_dump+0x51e/0x6d0
rtnl_fdb_dump+0x4dc/0xad0
netlink_dump+0x540/0x1090
__netlink_dump_start+0x695/0x950
rtnetlink_rcv_msg+0x802/0xbd0
netlink_rcv_skb+0x17a/0x480
rtnetlink_rcv+0x22/0x30
netlink_unicast+0x5ae/0x890
netlink_sendmsg+0x98a/0xf40
__sys_sendto+0x279/0x3b0
__x64_sys_sendto+0xe6/0x1a0
do_syscall_64+0x54/0xa0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fe14fa2ade0
Code: Bad RIP value.
RSP: 002b:00007fff75bb5b88 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00005614b1ba0020 RCX: 00007fe14fa2ade0
RDX: 000000000000011c RSI: 00007fff75bb5b90 RDI: 0000000000000003
RBP: 00007fff75bb5b90 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00005614b1b89160
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
Fixes: 5e6d243587 ("bridge: netlink dump interface at par with brctl")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 024a8168b7 ]
We observed two panics involving races with igb_reset_task.
The first panic is caused by this race condition:
kworker reboot -f
igb_reset_task
igb_reinit_locked
igb_down
napi_synchronize
__igb_shutdown
igb_clear_interrupt_scheme
igb_free_q_vectors
igb_free_q_vector
adapter->q_vector[v_idx] = NULL;
napi_disable
Panics trying to access
adapter->q_vector[v_idx].napi_state
The second panic (a divide error) is caused by this race:
kworker reboot -f tx packet
igb_reset_task
__igb_shutdown
rtnl_lock()
...
igb_clear_interrupt_scheme
igb_free_q_vectors
adapter->num_tx_queues = 0
...
rtnl_unlock()
rtnl_lock()
igb_reinit_locked
igb_down
igb_up
netif_tx_start_all_queues
dev_hard_start_xmit
igb_xmit_frame
igb_tx_queue_mapping
Panics on
r_idx % adapter->num_tx_queues
This commit applies to igb_reset_task the same changes that
were applied to ixgbe in commit 2f90b8657e ("ixgbe: this patch
adds support for DCB to the kernel and ixgbe driver"),
commit 8f4c5c9fb8 ("ixgbe: reinit_locked() should be called with
rtnl_lock") and commit 88adce4ea8 ("ixgbe: fix possible race in
reset subtask").
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Support for phys switch id ndo added for representors and if
we do not have representors there is no need to support it.
Since each port return different switch id supporting this
block support for creating bond over PFs and attaching to bridge
in legacy mode.
This bug doesn't exist upstream as the code got refactored and the
netdev api is totally different.
Fixes: cb67b83292 ("net/mlx5e: Introduce SRIOV VF representors")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c2c6331064 ]
There's a potential race in xennet_remove(); this is what the driver is
doing upon unregistering a network device:
1. state = read bus state
2. if state is not "Closed":
3. request to set state to "Closing"
4. wait for state to be set to "Closing"
5. request to set state to "Closed"
6. wait for state to be set to "Closed"
If the state changes to "Closed" immediately after step 1 we are stuck
forever in step 4, because the state will never go back from "Closed" to
"Closing".
Make sure to check also for state == "Closed" in step 4 to prevent the
deadlock.
Also add a 5 sec timeout any time we wait for the bus state to change,
to avoid getting stuck forever in wait_event().
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 015c5d5e6a ]
According to the report of [1], this driver is possible to cause
the following error in ravb_tx_timeout_work().
ravb e6800000.ethernet ethernet: failed to switch device to config mode
This error means that the hardware could not change the state
from "Operation" to "Configuration" while some tx and/or rx queue
are operating. After that, ravb_config() in ravb_dmac_init() will fail,
and then any descriptors will be not allocaled anymore so that NULL
pointer dereference happens after that on ravb_start_xmit().
To fix the issue, the ravb_tx_timeout_work() should check
the return values of ravb_stop_dma() and ravb_dmac_init().
If ravb_stop_dma() fails, ravb_tx_timeout_work() re-enables TX and RX
and just exits. If ravb_dmac_init() fails, just exits.
[1]
https://lore.kernel.org/linux-renesas-soc/20200518045452.2390-1-dirk.behme@de.bosch.com/
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d61e21852 ]
This is likely firmware causing this but its starting to annoy customers.
Change the message level to verbose to prevent the spam.
Note that this seems to only show up with ISCSI enabled on the HBA via the
qedi driver.
Signed-off-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0484010ec ]
On sparc32, tcflag_t is "unsigned long", unlike on all other
architectures, where it is "unsigned int":
drivers/net/usb/hso.c: In function ‘hso_serial_set_termios’:
include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 4 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=]
drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’
hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n",
^~~~~~~
include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 5 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=]
drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’
hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n",
^~~~~~~
As "unsigned long" is 32-bit on sparc32, fix this by casting all tcflag_t
parameters to "unsigned int".
While at it, use "%u" to format unsigned numbers.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27a2145d6f ]
RX queue IRQ mappings are disposed in both the TX IRQ and RX IRQ
error paths. Fix this and dispose of TX IRQ mappings correctly in
case of an error.
Fixes: ea22d51a78 ("ibmvnic: simplify and improve driver probe function")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d8e8f3433 ]
The lifetime of the Rx listener item ('rxl_item') is managed using RCU,
but is dereferenced outside of RCU read-side critical section, which can
lead to a use-after-free.
Fix this by increasing the scope of the RCU read-side critical section.
Fixes: 93c1edb27f ("mlxsw: Introduce Mellanox switch driver core")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d8e95fd6d ]
Add the missing endpoint sanity check to prevent a NULL-pointer
dereference should a malicious device lack the expected endpoints.
Note that the driver has a broken endpoint-lookup helper,
lan78xx_get_endpoints(), which can end up accepting interfaces in an
altsetting without endpoints as long as *some* altsetting has a bulk-in
and a bulk-out endpoint.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 728c1e2a05 ]
In ath9k_wmi_cmd, the allocated network buffer needs to be released
if timeout happens. Otherwise memory will be leaked.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 853acf7caf ]
In htc_config_pipe_credits, htc_setup_complete, and htc_connect_service
if time out happens, the allocated buffer needs to be released.
Otherwise there will be memory leak.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 297a6961ff ]
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fdcabeac3 ]
This driver is not working because of problems of its receiving code.
This patch fixes it to make it work.
When the driver receives an LAPB frame, it should first pass the frame
to the LAPB module to process. After processing, the LAPB module passes
the data (the packet) back to the driver, the driver should then add a
one-byte pseudo header and pass the data to upper layers.
The changes to the "x25_asy_bump" function and the
"x25_asy_data_indication" function are to correctly implement this
procedure.
Also, the "x25_asy_unesc" function ignores any frame that is shorter
than 3 bytes. However the shortest frames are 2-byte long. So we need
to change it to allow 2-byte frames to pass.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Reviewed-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bbcaaee1f upstream.
In ath9k_hif_usb_rx_cb interface number is assumed to be 0.
usb_ifnum_to_if(urb->dev, 0)
But it isn't always true.
The case reported by syzbot:
https://lore.kernel.org/linux-usb/000000000000666c9c05a1c05d12@google.com
usb 2-1: new high-speed USB device number 2 using dummy_hcd
usb 2-1: config 1 has an invalid interface number: 2 but max is 0
usb 2-1: config 1 has no interface number 0
usb 2-1: New USB device found, idVendor=0cf3, idProduct=9271, bcdDevice=
1.08
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
general protection fault, probably for non-canonical address
0xdffffc0000000015: 0000 [#1] SMP KASAN
KASAN: null-ptr-deref in range [0x00000000000000a8-0x00000000000000af]
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.0-rc5-syzkaller #0
Call Trace
__usb_hcd_giveback_urb+0x29a/0x550 drivers/usb/core/hcd.c:1650
usb_hcd_giveback_urb+0x368/0x420 drivers/usb/core/hcd.c:1716
dummy_timer+0x1258/0x32ae drivers/usb/gadget/udc/dummy_hcd.c:1966
call_timer_fn+0x195/0x6f0 kernel/time/timer.c:1404
expire_timers kernel/time/timer.c:1449 [inline]
__run_timers kernel/time/timer.c:1773 [inline]
__run_timers kernel/time/timer.c:1740 [inline]
run_timer_softirq+0x5f9/0x1500 kernel/time/timer.c:1786
__do_softirq+0x21e/0x950 kernel/softirq.c:292
invoke_softirq kernel/softirq.c:373 [inline]
irq_exit+0x178/0x1a0 kernel/softirq.c:413
exiting_irq arch/x86/include/asm/apic.h:546 [inline]
smp_apic_timer_interrupt+0x141/0x540 arch/x86/kernel/apic/apic.c:1146
apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:829
Reported-and-tested-by: syzbot+40d5d2e8a4680952f042@syzkaller.appspotmail.com
Signed-off-by: Qiujun Huang <hqjagain@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200404041838.10426-6-hqjagain@gmail.com
Cc: Viktor Jägersküpper <viktor_jaegerskuepper@freenet.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bca9749b1a ]
If try_toggle_control_gpio() failed in smc_drv_probe(), free_netdev(ndev)
should be called to free the ndev created earlier. Otherwise, a memleak
will occur.
Fixes: 7d2911c438 ("net: smc91x: Fix gpios for device tree based booting")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 473309fb83 ]
From Documentation/networking/timestamping.txt:
A driver which supports hardware time stamping shall update the
struct with the actual, possibly more permissive configuration.
Do update the struct passed when we upscale the requested time
stamping mode.
Fixes: cb646e2b02 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3195c4706b ]
The size used when calling 'pci_alloc_consistent()' and
'pci_free_consistent()' should match.
Fix it and have it consistent with the corresponding call in 'rr_close()'.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 163e9ef636 ]
The driver was modified to not rely on rtnl lock to protect link
settings about 2 years ago. The pause setting was missed when
making that change. Fix it by acquiring link_lock mutex before
calling bnxt_hwrm_set_pause().
Fixes: e2dc9b6e38 ("bnxt_en: Don't use rtnl lock to protect link change logic in workqueue.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28b18e4eb5 ]
clang static analysis flags this garbage return
drivers/net/ethernet/marvell/sky2.c:208:2: warning: Undefined or garbage value returned to caller [core.uninitialized.UndefReturn]
return v;
^~~~~~~~
static inline u16 gm_phy_read( ...
{
u16 v;
__gm_phy_read(hw, port, reg, &v);
return v;
}
__gm_phy_read can return without setting v.
So handle similar to skge.c's gm_phy_read, initialize v.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9dc829a135 ]
When this driver transmits data,
first this driver will remove a pseudo header of 1 byte,
then the lapb module will prepend the LAPB header of 2 or 3 bytes,
then this driver will prepend a length field of 2 bytes,
then the underlying Ethernet device will prepend its own header.
So, the header length required should be:
-1 + 3 + 2 + "the header length needed by the underlying device".
This patch fixes kernel panic when this driver is used with AF_PACKET
SOCK_DGRAM sockets.
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ced4799d06 ]
Change the way the "magic-packet" DT property is handled in the
macb_probe() function, matching DT binding documentation.
Now we mark the device as "wakeup capable" instead of calling the
device_init_wakeup() function that would enable the wakeup source.
For Ethernet WoL, enabling the wakeup_source is done by
using ethtool and associated macb_set_wol() function that
already calls device_set_wakeup_enable() for this purpose.
That would reduce power consumption by cutting more clocks if
"magic-packet" property is set but WoL is not configured by ethtool.
Fixes: 3e2a5e1539 ("net: macb: add wake-on-lan support via magic packet")
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Harini Katakam <harini.katakam@xilinx.com>
Cc: Sergio Prado <sergio.prado@e-labworks.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ed58f96a7 ]
In a case where the ID_REV register read is failed, the memory for a
private data structure has to be freed before returning error from the
function smsc95xx_bind.
Fixes: bbd9f9ee69 ("smsc95xx: add wol support for more frame types")
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c8b1e855f ]
The return value of the function smsc95xx_reset() must be checked
to avoid returning false success from the function smsc95xx_bind().
Fixes: 2f7ca802bd ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
