[ Upstream commit 3bb23421a5 ]
We need to update lastuse to to the most updated value between what
is already set and the new value.
If HW matching fails, i.e. because of an issue, the stats are not updated
but it could be that software did match and updated lastuse.
Fixes: 5712bf9c5c ("net/sched: act_mirred: Use passed lastuse argument")
Fixes: 9fea47d93b ("net/sched: act_gact: Update statistics when offloaded to hardware")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 71891e2dab ]
In kernel log ths message appears on every boot:
"warning: `NetworkChangeNo' uses legacy ethtool link settings API,
link modes are only partially reported"
When ethtool link settings API changed, it started complaining about
usages of old API. Ironically, the original patch was from google but
the application using the legacy API is chrome.
Linux ABI is fixed as much as possible. The kernel must not break it
and should not complain about applications using legacy API's.
This patch just removes the warning since using legacy API's
in Linux is perfectly acceptable.
Fixes: 3f1ac7a700 ("net: ethtool: add new ETHTOOL_xLINKSETTINGS API")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c095508770 ]
When args->nr_local is 0, nr_pages gets also 0 due some size
calculation via rds_rm_size(), which is later used to allocate
pages for DMA, this bug produces a heap Out-Of-Bound write access
to a specific memory region.
Signed-off-by: Mohamed Ghannam <simo.ghannam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 23263ec86a ]
When an ip6_tunnel is in mode 'any', where the transport layer
protocol can be either 4 or 41, dst_cache must be disabled.
This is because xfrm policies might apply to only one of the two
protocols. Caching dst would cause xfrm policies for one protocol
incorrectly used for the other.
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 78bbb15f22 ]
A vlan device with vid 0 is allow to creat by not able to be fully
cleaned up by unregister_vlan_dev() which checks for vlan_id!=0.
Also, VLAN 0 is probably not a valid number and it is kinda
"reserved" for HW accelerating devices, but it is probably too
late to reject it from creation even if makes sense. Instead,
just remove the check in unregister_vlan_dev().
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Fixes: ad1afb0039 ("vlan_dev: VLAN 0 should be treated as "no vlan tag" (802.1p packet)")
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 600647d467 upstream.
Fix BBR so that upon notification of a loss recovery undo BBR resets
long-term bandwidth sampling.
Under high reordering, reordering events can be interpreted as loss.
If the reordering and spurious loss estimates are high enough, this
can cause BBR to spuriously estimate that we are seeing loss rates
high enough to trigger long-term bandwidth estimation. To avoid that
problem, this commit resets long-term bandwidth sampling on loss
recovery undo events.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f6c498e4f upstream.
Fix BBR so that upon notification of a loss recovery undo BBR resets
the full pipe detection (STARTUP exit) state machine.
Under high reordering, reordering events can be interpreted as loss.
If the reordering and spurious loss estimates are high enough, this
could previously cause BBR to spuriously estimate that the pipe is
full.
Since spurious loss recovery means that our overall sending will have
slowed down spuriously, this commit gives a flow more time to probe
robustly for bandwidth and decide the pipe is really full.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d4761754b4 ]
Mark tcp_sock during a SACK reneging event and invalidate rate samples
while marked. Such rate samples may overestimate bw by including packets
that were SACKed before reneging.
< ack 6001 win 10000 sack 7001:38001
< ack 7001 win 0 sack 8001:38001 // Reneg detected
> seq 7001:8001 // RTO, SACK cleared.
< ack 38001 win 10000
In above example the rate sample taken after the last ack will count
7001-38001 as delivered while the actual delivery rate likely could
be much lower i.e. 7001-8001.
This patch adds a new field tcp_sock.sack_reneg and marks it when we
declare SACK reneging and entering TCP_CA_Loss, and unmarks it after
the last rate sample was taken before moving back to TCP_CA_Open. This
patch also invalidates rate samples taken while tcp_sock.is_sack_reneg
is set.
Fixes: b9f64820fb ("tcp: track data delivery rate for a TCP connection")
Signed-off-by: Yousuk Seung <ysseung@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 35b99dffc3 ]
skb_complete_tx_timestamp must ingest the skb it is passed. Call
kfree_skb if the skb cannot be enqueued.
Fixes: b245be1f4d ("net-timestamp: no-payload only sysctl")
Fixes: 9ac25fc063 ("net: fix socket refcounting in skb_complete_tx_timestamp()")
Reported-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 21b5944350 ]
(I can trivially verify that that idr_remove in cleanup_net happens
after the network namespace count has dropped to zero --EWB)
Function get_net_ns_by_id() does not check for net::count
after it has found a peer in netns_ids idr.
It may dereference a peer, after its count has already been
finaly decremented. This leads to double free and memory
corruption:
put_net(peer) rtnl_lock()
atomic_dec_and_test(&peer->count) [count=0] ...
__put_net(peer) get_net_ns_by_id(net, id)
spin_lock(&cleanup_list_lock)
list_add(&net->cleanup_list, &cleanup_list)
spin_unlock(&cleanup_list_lock)
queue_work() peer = idr_find(&net->netns_ids, id)
| get_net(peer) [count=1]
| ...
| (use after final put)
v ...
cleanup_net() ...
spin_lock(&cleanup_list_lock) ...
list_replace_init(&cleanup_list, ..) ...
spin_unlock(&cleanup_list_lock) ...
... ...
... put_net(peer)
... atomic_dec_and_test(&peer->count) [count=0]
... spin_lock(&cleanup_list_lock)
... list_add(&net->cleanup_list, &cleanup_list)
... spin_unlock(&cleanup_list_lock)
... queue_work()
... rtnl_unlock()
rtnl_lock() ...
for_each_net(tmp) { ...
id = __peernet2id(tmp, peer) ...
spin_lock_irq(&tmp->nsid_lock) ...
idr_remove(&tmp->netns_ids, id) ...
... ...
net_drop_ns() ...
net_free(peer) ...
} ...
|
v
cleanup_net()
...
(Second free of peer)
Also, put_net() on the right cpu may reorder with left's cpu
list_replace_init(&cleanup_list, ..), and then cleanup_list
will be corrupted.
Since cleanup_net() is executed in worker thread, while
put_net(peer) can happen everywhere, there should be
enough time for concurrent get_net_ns_by_id() to pick
the peer up, and the race does not seem to be unlikely.
The patch fixes the problem in standard way.
(Also, there is possible problem in peernet2id_alloc(), which requires
check for net::count under nsid_lock and maybe_get_net(peer), but
in current stable kernel it's used under rtnl_lock() and it has to be
safe. Openswitch begun to use peernet2id_alloc(), and possibly it should
be fixed too. While this is not in stable kernel yet, so I'll send
a separate message to netdev@ later).
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Fixes: 0c7aecd4bd "netns: add rtnl cmd to add and get peer netns ids"
Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 84aeb437ab ]
The early call to br_stp_change_bridge_id in bridge's newlink can cause
a memory leak if an error occurs during the newlink because the fdb
entries are not cleaned up if a different lladdr was specified, also
another minor issue is that it generates fdb notifications with
ifindex = 0. Another unrelated memory leak is the bridge sysfs entries
which get added on NETDEV_REGISTER event, but are not cleaned up in the
newlink error path. To remove this special case the call to
br_stp_change_bridge_id is done after netdev register and we cleanup the
bridge on changelink error via br_dev_delete to plug all leaks.
This patch makes netlink bridge destruction on newlink error the same as
dellink and ioctl del which is necessary since at that point we have a
fully initialized bridge device.
To reproduce the issue:
$ ip l add br0 address 00:11:22:33:44:55 type bridge group_fwd_mask 1
RTNETLINK answers: Invalid argument
$ rmmod bridge
[ 1822.142525] =============================================================================
[ 1822.143640] BUG bridge_fdb_cache (Tainted: G O ): Objects remaining in bridge_fdb_cache on __kmem_cache_shutdown()
[ 1822.144821] -----------------------------------------------------------------------------
[ 1822.145990] Disabling lock debugging due to kernel taint
[ 1822.146732] INFO: Slab 0x0000000092a844b2 objects=32 used=2 fp=0x00000000fef011b0 flags=0x1ffff8000000100
[ 1822.147700] CPU: 2 PID: 13584 Comm: rmmod Tainted: G B O 4.15.0-rc2+ #87
[ 1822.148578] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[ 1822.150008] Call Trace:
[ 1822.150510] dump_stack+0x78/0xa9
[ 1822.151156] slab_err+0xb1/0xd3
[ 1822.151834] ? __kmalloc+0x1bb/0x1ce
[ 1822.152546] __kmem_cache_shutdown+0x151/0x28b
[ 1822.153395] shutdown_cache+0x13/0x144
[ 1822.154126] kmem_cache_destroy+0x1c0/0x1fb
[ 1822.154669] SyS_delete_module+0x194/0x244
[ 1822.155199] ? trace_hardirqs_on_thunk+0x1a/0x1c
[ 1822.155773] entry_SYSCALL_64_fastpath+0x23/0x9a
[ 1822.156343] RIP: 0033:0x7f929bd38b17
[ 1822.156859] RSP: 002b:00007ffd160e9a98 EFLAGS: 00000202 ORIG_RAX: 00000000000000b0
[ 1822.157728] RAX: ffffffffffffffda RBX: 00005578316ba090 RCX: 00007f929bd38b17
[ 1822.158422] RDX: 00007f929bd9ec60 RSI: 0000000000000800 RDI: 00005578316ba0f0
[ 1822.159114] RBP: 0000000000000003 R08: 00007f929bff5f20 R09: 00007ffd160e8a11
[ 1822.159808] R10: 00007ffd160e9860 R11: 0000000000000202 R12: 00007ffd160e8a80
[ 1822.160513] R13: 0000000000000000 R14: 0000000000000000 R15: 00005578316ba090
[ 1822.161278] INFO: Object 0x000000007645de29 @offset=0
[ 1822.161666] INFO: Object 0x00000000d5df2ab5 @offset=128
Fixes: 30313a3d57 ("bridge: Handle IFLA_ADDRESS correctly when creating bridge device")
Fixes: 5b8d5429da ("bridge: netlink: register netdevice before executing changelink")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b4681c2829 ]
Since commit 0ddcf43d5d ("ipv4: FIB Local/MAIN table collapse") the
local table uses the same trie allocated for the main table when custom
rules are not in use.
When a net namespace is dismantled, the main table is flushed and freed
(via an RCU callback) before the local table. In case the callback is
invoked before the local table is iterated, a use-after-free can occur.
Fix this by iterating over the FIB tables in reverse order, so that the
main table is always freed after the local table.
v3: Reworded comment according to Alex's suggestion.
v2: Add a comment to make the fix more explicit per Dave's and Alex's
feedback.
Fixes: 0ddcf43d5d ("ipv4: FIB Local/MAIN table collapse")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 74c4b656c3 ]
commit 8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
introduced new exit point in ipxip6_rcv. however rcu_read_unlock is
missing there. this diff is fixing this
v1->v2:
instead of doing rcu_read_unlock in place, we are going to "drop"
section (to prevent skb leakage)
Fixes: 8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
Signed-off-by: Nikita V. Shirokov <tehnerd@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8cb38a6024 ]
The patch(180d8cd942) replaces all uses of struct sock fields'
memory_pressure, memory_allocated, sockets_allocated, and sysctl_mem
to accessor macros. But the sockets_allocated field of sctp sock is
not replaced at all. Then replace it now for unifying the code.
Fixes: 180d8cd942 ("foundations of per-cgroup memory pressure controlling.")
Cc: Glauber Costa <glommer@parallels.com>
Signed-off-by: Tonghao Zhang <zhangtonghao@didichuxing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8f659a03a0 ]
inet->hdrincl is racy, and could lead to uninitialized stack pointer
usage, so its value should be read only once.
Fixes: c008ba5bdc ("ipv4: Avoid reading user iov twice after raw_probe_proto_opt")
Signed-off-by: Mohamed Ghannam <simo.ghannam@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 30791ac419 ]
The MD5-key that belongs to a connection is identified by the peer's
IP-address. When we are in tcp_v4(6)_reqsk_send_ack(), we are replying
to an incoming segment from tcp_check_req() that failed the seq-number
checks.
Thus, to find the correct key, we need to use the skb's saddr and not
the daddr.
This bug seems to have been there since quite a while, but probably got
unnoticed because the consequences are not catastrophic. We will call
tcp_v4_reqsk_send_ack only to send a challenge-ACK back to the peer,
thus the connection doesn't really fail.
Fixes: 9501f97229 ("tcp md5sig: Let the caller pass appropriate key for tcp_v{4,6}_do_calc_md5_hash().")
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c589e69b50 ]
This commit records the "full bw reached" decision in a new
full_bw_reached bit. This is a pure refactor that does not change the
current behavior, but enables subsequent fixes and improvements.
In particular, this enables simple and clean fixes because the full_bw
and full_bw_cnt can be unconditionally zeroed without worrying about
forgetting that we estimated we filled the pipe in Startup. And it
enables future improvements because multiple code paths can be used
for estimating that we filled the pipe in Startup; any new code paths
only need to set this bit when they think the pipe is full.
Note that this fix intentionally reduces the width of the full_bw_cnt
counter, since we have never used the most significant bit.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 14e138a86f ]
RDS currently doesn't check if the length of the control message is
large enough to hold the required data, before dereferencing the control
message data. This results in following crash:
BUG: KASAN: stack-out-of-bounds in rds_rdma_bytes net/rds/send.c:1013
[inline]
BUG: KASAN: stack-out-of-bounds in rds_sendmsg+0x1f02/0x1f90
net/rds/send.c:1066
Read of size 8 at addr ffff8801c928fb70 by task syzkaller455006/3157
CPU: 0 PID: 3157 Comm: syzkaller455006 Not tainted 4.15.0-rc3+ #161
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:53
print_address_description+0x73/0x250 mm/kasan/report.c:252
kasan_report_error mm/kasan/report.c:351 [inline]
kasan_report+0x25b/0x340 mm/kasan/report.c:409
__asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:430
rds_rdma_bytes net/rds/send.c:1013 [inline]
rds_sendmsg+0x1f02/0x1f90 net/rds/send.c:1066
sock_sendmsg_nosec net/socket.c:628 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:638
___sys_sendmsg+0x320/0x8b0 net/socket.c:2018
__sys_sendmmsg+0x1ee/0x620 net/socket.c:2108
SYSC_sendmmsg net/socket.c:2139 [inline]
SyS_sendmmsg+0x35/0x60 net/socket.c:2134
entry_SYSCALL_64_fastpath+0x1f/0x96
RIP: 0033:0x43fe49
RSP: 002b:00007fffbe244ad8 EFLAGS: 00000217 ORIG_RAX: 0000000000000133
RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 000000000043fe49
RDX: 0000000000000001 RSI: 000000002020c000 RDI: 0000000000000003
RBP: 00000000006ca018 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000217 R12: 00000000004017b0
R13: 0000000000401840 R14: 0000000000000000 R15: 0000000000000000
To fix this, we verify that the cmsg_len is large enough to hold the
data to be read, before proceeding further.
Reported-by: syzbot <syzkaller-bugs@googlegroups.com>
Signed-off-by: Avinash Repaka <avinash.repaka@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 513674b5a2 ]
sysctl.ip6.auto_flowlabels is default 1. In our hosts, we set it to 2.
If sockopt doesn't set autoflowlabel, outcome packets from the hosts are
supposed to not include flowlabel. This is true for normal packet, but
not for reset packet.
The reason is ipv6_pinfo.autoflowlabel is set in sock creation. Later if
we change sysctl.ip6.auto_flowlabels, the ipv6_pinfo.autoflowlabel isn't
changed, so the sock will keep the old behavior in terms of auto
flowlabel. Reset packet is suffering from this problem, because reset
packet is sent from a special control socket, which is created at boot
time. Since sysctl.ipv6.auto_flowlabels is 1 by default, the control
socket will always have its ipv6_pinfo.autoflowlabel set, even after
user set sysctl.ipv6.auto_flowlabels to 1, so reset packset will always
have flowlabel. Normal sock created before sysctl setting suffers from
the same issue. We can't even turn off autoflowlabel unless we kill all
socks in the hosts.
To fix this, if IPV6_AUTOFLOWLABEL sockopt is used, we use the
autoflowlabel setting from user, otherwise we always call
ip6_default_np_autolabel() which has the new settings of sysctl.
Note, this changes behavior a little bit. Before commit 42240901f7
(ipv6: Implement different admin modes for automatic flow labels), the
autoflowlabel behavior of a sock isn't sticky, eg, if sysctl changes,
existing connection will change autoflowlabel behavior. After that
commit, autoflowlabel behavior is sticky in the whole life of the sock.
With this patch, the behavior isn't sticky again.
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Tom Herbert <tom@quantonium.net>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 93c647643b ]
Currently, a nlmon link inside a child namespace can observe systemwide
netlink activity. Filter the traffic so that nlmon can only sniff
netlink messages from its own netns.
Test case:
vpnns -- bash -c "ip link add nlmon0 type nlmon; \
ip link set nlmon0 up; \
tcpdump -i nlmon0 -q -w /tmp/nlmon.pcap -U" &
sudo ip xfrm state add src 10.1.1.1 dst 10.1.1.2 proto esp \
spi 0x1 mode transport \
auth sha1 0x6162633132330000000000000000000000000000 \
enc aes 0x00000000000000000000000000000000
grep --binary abc123 /tmp/nlmon.pcap
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a46182b002 ]
Closing a multicast socket after the final IPv4 address is deleted
from an interface can generate a membership report that uses the
source IP from a different interface. The following test script, run
from an isolated netns, reproduces the issue:
#!/bin/bash
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link set dummy0 up
ip link set dummy1 up
ip addr add 10.1.1.1/24 dev dummy0
ip addr add 192.168.99.99/24 dev dummy1
tcpdump -U -i dummy0 &
socat EXEC:"sleep 2" \
UDP4-DATAGRAM:239.101.1.68:8889,ip-add-membership=239.0.1.68:10.1.1.1 &
sleep 1
ip addr del 10.1.1.1/24 dev dummy0
sleep 5
kill %tcpdump
RFC 3376 specifies that the report must be sent with a valid IP source
address from the destination subnet, or from address 0.0.0.0. Add an
extra check to make sure this is the case.
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b5476022bb ]
IPv4 stack reacts to changes to small MTU, by disabling itself under
RTNL.
But there is a window where threads not using RTNL can see a wrong
device mtu. This can lead to surprises, in igmp code where it is
assumed the mtu is suitable.
Fix this by reading device mtu once and checking IPv4 minimal MTU.
This patch adds missing IPV4_MIN_MTU define, to not abuse
ETH_MIN_MTU anymore.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f372c7bfb ]
The NS for DAD are sent on admin up as long as a valid qdisc is found.
A race condition exists by which these packets will not egress the
interface if the operational state of the lower device is not yet up.
The solution is to delay DAD until the link is operationally up
according to RFC2863. Rather than only doing this, follow the existing
code checks by deferring IPv6 device initialization altogether. The fix
allows DAD on devices like tunnels that are controlled by userspace
control plane. The fix has no impact on regular deployments, but means
that there is no IPv6 connectivity until the port has been opened in
the case of port-based network access control, which should be
desirable.
Signed-off-by: Mike Manning <mmanning@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ffefb6f4d6 ]
Our chosen ic_dev may be anywhere in our list of ic_devs, and we may
free it before attempting to close others. When we compare d->dev and
ic_dev->dev, we're potentially dereferencing memory returned to the
allocator. This causes KASAN to scream for each subsequent ic_dev we
check.
As there's a 1-1 mapping between ic_devs and netdevs, we can instead
compare d and ic_dev directly, which implicitly handles the !ic_dev
case, and avoids the use-after-free. The ic_dev pointer may be stale,
but we will not dereference it.
Original splat:
[ 6.487446] ==================================================================
[ 6.494693] BUG: KASAN: use-after-free in ic_close_devs+0xc4/0x154 at addr ffff800367efa708
[ 6.503013] Read of size 8 by task swapper/0/1
[ 6.507452] CPU: 5 PID: 1 Comm: swapper/0 Not tainted 4.11.0-rc3-00002-gda42158 #8
[ 6.514993] Hardware name: AppliedMicro Mustang/Mustang, BIOS 3.05.05-beta_rc Jan 27 2016
[ 6.523138] Call trace:
[ 6.525590] [<ffff200008094778>] dump_backtrace+0x0/0x570
[ 6.530976] [<ffff200008094d08>] show_stack+0x20/0x30
[ 6.536017] [<ffff200008bee928>] dump_stack+0x120/0x188
[ 6.541231] [<ffff20000856d5e4>] kasan_object_err+0x24/0xa0
[ 6.546790] [<ffff20000856d924>] kasan_report_error+0x244/0x738
[ 6.552695] [<ffff20000856dfec>] __asan_report_load8_noabort+0x54/0x80
[ 6.559204] [<ffff20000aae86ac>] ic_close_devs+0xc4/0x154
[ 6.564590] [<ffff20000aaedbac>] ip_auto_config+0x2ed4/0x2f1c
[ 6.570321] [<ffff200008084b04>] do_one_initcall+0xcc/0x370
[ 6.575882] [<ffff20000aa31de8>] kernel_init_freeable+0x5f8/0x6c4
[ 6.581959] [<ffff20000a16df00>] kernel_init+0x18/0x190
[ 6.587171] [<ffff200008084710>] ret_from_fork+0x10/0x40
[ 6.592468] Object at ffff800367efa700, in cache kmalloc-128 size: 128
[ 6.598969] Allocated:
[ 6.601324] PID = 1
[ 6.603427] save_stack_trace_tsk+0x0/0x418
[ 6.607603] save_stack_trace+0x20/0x30
[ 6.611430] kasan_kmalloc+0xd8/0x188
[ 6.615087] ip_auto_config+0x8c4/0x2f1c
[ 6.619002] do_one_initcall+0xcc/0x370
[ 6.622832] kernel_init_freeable+0x5f8/0x6c4
[ 6.627178] kernel_init+0x18/0x190
[ 6.630660] ret_from_fork+0x10/0x40
[ 6.634223] Freed:
[ 6.636233] PID = 1
[ 6.638334] save_stack_trace_tsk+0x0/0x418
[ 6.642510] save_stack_trace+0x20/0x30
[ 6.646337] kasan_slab_free+0x88/0x178
[ 6.650167] kfree+0xb8/0x478
[ 6.653131] ic_close_devs+0x130/0x154
[ 6.656875] ip_auto_config+0x2ed4/0x2f1c
[ 6.660875] do_one_initcall+0xcc/0x370
[ 6.664705] kernel_init_freeable+0x5f8/0x6c4
[ 6.669051] kernel_init+0x18/0x190
[ 6.672534] ret_from_fork+0x10/0x40
[ 6.676098] Memory state around the buggy address:
[ 6.680880] ffff800367efa600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 6.688078] ffff800367efa680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 6.695276] >ffff800367efa700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 6.702469] ^
[ 6.705952] ffff800367efa780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 6.713149] ffff800367efa800: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 6.720343] ==================================================================
[ 6.727536] Disabling lock debugging due to kernel taint
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: David S. Miller <davem@davemloft.net>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 75c689dca9 ]
In the commit 93557f53e1 ("netfilter: nf_conntrack: nf_conntrack snmp
helper"), the snmp_helper is replaced by nf_nat_snmp_hook. So the
snmp_helper is never registered. But it still tries to unregister the
snmp_helper, it could cause the panic.
Now remove the useless snmp_helper and the unregister call in the
error handler.
Fixes: 93557f53e1 ("netfilter: nf_conntrack: nf_conntrack snmp helper")
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 83d90219a5 ]
The nf_ct_helper_hash table is protected by nf_ct_helper_mutex, while
nfct_helper operation is protected by nfnl_lock(NFNL_SUBSYS_CTHELPER).
So it's possible that one CPU is walking the nf_ct_helper_hash for
cthelper add/get/del, another cpu is doing nf_conntrack_helpers_unregister
at the same time. This is dangrous, and may cause use after free error.
Note, delete operation will flush all cthelpers added via nfnetlink, so
using rcu to do protect is not easy.
Now introduce a dummy list to record all the cthelpers added via
nfnetlink, then we can walk the dummy list instead of walking the
nf_ct_helper_hash. Also, keep nfnl_cthelper_dump_table unchanged, it
may be invoked without nfnl_lock(NFNL_SUBSYS_CTHELPER) held.
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 95f2552113 ]
This change basically codifies what I think was already the limitations on
the busy_poll and busy_read sysctl interfaces. We weren't checking the
lower bounds and as such could input negative values. The behavior when
that was used was dependent on the architecture. In order to prevent any
issues with that I am just disabling support for values less than 0 since
this way we don't have to worry about any odd behaviors.
By limiting the sysctl values this way it also makes it consistent with how
we handle the SO_BUSY_POLL socket option since the value appears to be
reported as a signed integer value and negative values are rejected.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 557d054c01 ]
Until now, tipc_nametbl_unsubscribe() is called at subscriptions
reference count cleanup. Usually the subscriptions cleanup is
called at subscription timeout or at subscription cancel or at
subscriber delete.
We have ignored the possibility of this being called from other
locations, which causes deadlock as we try to grab the
tn->nametbl_lock while holding it already.
CPU1: CPU2:
---------- ----------------
tipc_nametbl_publish
spin_lock_bh(&tn->nametbl_lock)
tipc_nametbl_insert_publ
tipc_nameseq_insert_publ
tipc_subscrp_report_overlap
tipc_subscrp_get
tipc_subscrp_send_event
tipc_close_conn
tipc_subscrb_release_cb
tipc_subscrb_delete
tipc_subscrp_put
tipc_subscrp_put
tipc_subscrp_kref_release
tipc_nametbl_unsubscribe
spin_lock_bh(&tn->nametbl_lock)
<<grab nametbl_lock again>>
CPU1: CPU2:
---------- ----------------
tipc_nametbl_stop
spin_lock_bh(&tn->nametbl_lock)
tipc_purge_publications
tipc_nameseq_remove_publ
tipc_subscrp_report_overlap
tipc_subscrp_get
tipc_subscrp_send_event
tipc_close_conn
tipc_subscrb_release_cb
tipc_subscrb_delete
tipc_subscrp_put
tipc_subscrp_put
tipc_subscrp_kref_release
tipc_nametbl_unsubscribe
spin_lock_bh(&tn->nametbl_lock)
<<grab nametbl_lock again>>
In this commit, we advance the calling of tipc_nametbl_unsubscribe()
from the refcount cleanup to the intended callers.
Fixes: d094c4d5f5 ("tipc: add subscription refcount to avoid invalid delete")
Reported-by: John Thompson <thompa.atl@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit aea92fb2e0 ]
skb_cow(skb, sizeof(ip header)) is not very helpful in this context.
First we need to use pskb_may_pull() to make sure the ip header
is in skb linear part, then use skb_try_make_writable() to
address clones issues.
Fixes: 4c30719f4f ("[PKT_SCHED] dsmark: handle cloned and non-linear skb's")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 380feae0de ]
Otherwise we'll leave the packets queued until releasing vsock device.
E.g., if guest is slow to start up, resulting ETIMEDOUT on connect, guest
will get the connect requests from failed host sockets.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Peng Tao <bergwolf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8a0f5ccfb3 ]
On Tue, Mar 14, 2017 at 10:44:10AM +0100, Dmitry Vyukov wrote:
>
> Yes, please.
> Disregarding some reports is not a good way long term.
Please try this patch.
---8<---
Subject: netlink: Annotate nlk cb_mutex by protocol
Currently all occurences of nlk->cb_mutex are annotated by lockdep
as a single class. This causes a false lcokdep cycle involving
genl and crypto_user.
This patch fixes it by dividing cb_mutex into individual classes
based on the netlink protocol. As genl and crypto_user do not
use the same netlink protocol this breaks the false dependency
loop.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 258bbb1b0e ]
The ICMP implementation currently replies to an ICMP time exceeded message
(type 11) with an ICMP host unreachable message (type 3, code 1).
However, time exceeded messages can either represent "time to live exceeded
in transit" (code 0) or "fragment reassembly time exceeded" (code 1).
Unconditionally replying to "fragment reassembly time exceeded" with
host unreachable messages might cause unjustified connection resets
which are now easily triggered as UFO has been removed, because, in turn,
sending large buffers triggers IP fragmentation.
The issue can be easily reproduced by running a lot of UDP streams
which is likely to trigger IP fragmentation:
# start netserver in the test namespace
ip netns add test
ip netns exec test netserver
# create a VETH pair
ip link add name veth0 type veth peer name veth0 netns test
ip link set veth0 up
ip -n test link set veth0 up
for i in $(seq 20 29); do
# assign addresses to both ends
ip addr add dev veth0 192.168.$i.1/24
ip -n test addr add dev veth0 192.168.$i.2/24
# start the traffic
netperf -L 192.168.$i.1 -H 192.168.$i.2 -t UDP_STREAM -l 0 &
done
# wait
send_data: data send error: No route to host (errno 113)
netperf: send_omni: send_data failed: No route to host
We need to differentiate instead: if fragment reassembly time exceeded
is reported, we need to silently drop the packet,
if time to live exceeded is reported, maintain the current behaviour.
In both cases increment the related error count "icmpInTimeExcds".
While at it, fix a typo in a comment, and convert the if statement
into a switch to mate it more readable.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c5504f724c ]
Information about ipvs in different network namespace can be seen via procfs.
How to reproduce:
# ip netns add ns01
# ip netns add ns02
# ip netns exec ns01 ip a add dev lo 127.0.0.1/8
# ip netns exec ns02 ip a add dev lo 127.0.0.1/8
# ip netns exec ns01 ipvsadm -A -t 10.1.1.1:80
# ip netns exec ns02 ipvsadm -A -t 10.1.1.2:80
The ipvsadm displays information about its own network namespace only.
# ip netns exec ns01 ipvsadm -Ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 10.1.1.1:80 wlc
# ip netns exec ns02 ipvsadm -Ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 10.1.1.2:80 wlc
But I can see information about other network namespace via procfs.
# ip netns exec ns01 cat /proc/net/ip_vs
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 0A010101:0050 wlc
TCP 0A010102:0050 wlc
# ip netns exec ns02 cat /proc/net/ip_vs
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 0A010102:0050 wlc
Signed-off-by: KUWAZAWA Takuya <albatross0@gmail.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4d4a6ac73e ]
If we receive a BUSY packet for a call we think we've just completed, the
packet is handed off to the connection processor to deal with - but the
connection processor doesn't expect a BUSY packet and so flags a protocol
error.
Fix this by simply ignoring the BUSY packet for the moment.
The symptom of this may appear as a system call failing with EPROTO. This
may be triggered by pressing ctrl-C under some circumstances.
This comes about we abort calls due to interruption by a signal (which we
shouldn't do, but that's going to be a large fix and mostly in fs/afs/).
What happens is that we abort the call and may also abort follow up calls
too (this needs offloading somehoe). So we see a transmission of something
like the following sequence of packets:
DATA for call N
ABORT call N
DATA for call N+1
ABORT call N+1
in very quick succession on the same channel. However, the peer may have
deferred the processing of the ABORT from the call N to a background thread
and thus sees the DATA message from the call N+1 coming in before it has
cleared the channel. Thus it sends a BUSY packet[*].
[*] Note that some implementations (OpenAFS, for example) mark the BUSY
packet with one plus the callNumber of the call prior to call N.
Ordinarily, this would be call N, but there's no requirement for the
calls on a channel to be numbered strictly sequentially (the number is
required to increase).
This is wrong and means that the callNumber in the BUSY packet should
be ignored (it really ought to be N+1 since that's what it's in
response to).
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 61733c91c4 ]
Alive tracking of nexthops can account for a link twice if the carrier
goes down followed by an admin down of the same link rendering multipath
routes useless. This is similar to 79099aab38 for UNREGISTER events and
DOWN events.
Fix by tracking number of alive nexthops in mpls_ifdown similar to the
logic in mpls_ifup. Checking the flags per nexthop once after all events
have been processed is simpler than trying to maintian a running count
through all event combinations.
Also, WRITE_ONCE is used instead of ACCESS_ONCE to set rt_nhn_alive
per a comment from checkpatch:
WARNING: Prefer WRITE_ONCE(<FOO>, <BAR>) over ACCESS_ONCE(<FOO>) = <BAR>
Fixes: c89359a42e ("mpls: support for dead routes")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 37c343b4f4 ]
When we notify peers of potential changes, it's also good to update
IGMP memberships. For example, during VM migration, updating IGMP
memberships will redirect existing multicast streams to the VM at the
new location.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
