[ Upstream commit 4d378f2ae5 ]
There is a deadlock in oxu_bus_suspend(), which is shown below:
(Thread 1) | (Thread 2)
| timer_action()
oxu_bus_suspend() | mod_timer()
spin_lock_irq() //(1) | (wait a time)
... | oxu_watchdog()
del_timer_sync() | spin_lock_irq() //(2)
(wait timer to stop) | ...
We hold oxu->lock in position (1) of thread 1, and use
del_timer_sync() to wait timer to stop, but timer handler
also need oxu->lock in position (2) of thread 2. As a result,
oxu_bus_suspend() will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irq(), which could let timer handler to obtain
the needed lock.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417120305.64577-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e91ac20889 ]
In some situations software handles TRB events slower than adding TRBs.
If the number of TRB events to be processed in a given interrupt is exactly
the same as the event ring size 256, then the local variable
"event_ring_deq" that holds the initial dequeue position is equal to
software_dequeue after handling all 256 interrupts.
It will cause driver to not update ERDP to hardware,
Software dequeue pointer is out of sync with ERDP on interrupt exit.
On the next interrupt, the event ring may full but driver will not
update ERDP as software_dequeue is equal to ERDP.
[ 536.377115] xhci_hcd 0000:00:12.0: ERROR unknown event type 37
[ 566.933173] sd 8:0:0:0: [sdb] tag#27 uas_eh_abort_handler 0 uas-tag 7 inflight: CMD OUT
[ 566.933181] sd 8:0:0:0: [sdb] tag#27 CDB: Write(10) 2a 00 17 71 e6 78 00 00 08 00
[ 572.041186] xhci_hcd On some situataions,the0000:00:12.0: xHCI host not responding to stop endpoint command.
[ 572.057193] xhci_hcd 0000:00:12.0: Host halt failed, -110
[ 572.057196] xhci_hcd 0000:00:12.0: xHCI host controller not responding, assume dead
[ 572.057236] sd 8:0:0:0: [sdb] tag#26 uas_eh_abort_handler 0 uas-tag 6 inflight: CMD
[ 572.057240] sd 8:0:0:0: [sdb] tag#26 CDB: Write(10) 2a 00 38 eb cc d8 00 00 08 00
[ 572.057244] sd 8:0:0:0: [sdb] tag#25 uas_eh_abort_handler 0 uas-tag 5 inflight: CMD
Hardware ERDP is updated mid event handling if there are more than 128
events in an interrupt (half of ring size).
Fix this by updating the software local variable at the same time as
hardware ERDP.
[commit message rewording -Mathias]
Fixes: dc0ffbea57 ("usb: host: xhci: update event ring dequeue pointer on purpose")
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220408134823.2527272-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 33597f0c48 upstream.
The first U3 wake signal by the host may be lost if the USB 3 connection is
tunneled over USB4, with a runtime suspended USB4 host, and firmware
implemented connection manager.
Specs state the host must wait 100ms (tU3WakeupRetryDelay) before
resending a U3 wake signal if device doesn't respond, leading to U3 -> U0
link transition times around 270ms in the tunneled case.
Fixes: 0200b9f790 ("xhci: Wait until link state trainsits to U0 after setting USB_SS_PORT_LS_U0")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220408134823.2527272-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc92944a01 upstream.
While rebooting, XHCI controller and its bus device will be shut down
in order by .shutdown callback. Stopping roothubs polling in
xhci_shutdown() can prevent XHCI driver from accessing port status
after its bus device shutdown.
Take PCIe XHCI controller as example, if XHCI driver doesn't stop roothubs
polling, XHCI driver may access PCIe BAR register for port status after
parent PCIe root port driver is shutdown and cause PCIe bus error.
[check shared hcd exist before stopping its roothub polling -Mathias]
Cc: stable@vger.kernel.org
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220408134823.2527272-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05519b8589 upstream.
xhci_decode_ctrl_ctx() returns the untouched buffer as-is if both "drop"
and "add" parameters are zero.
Fix the function to return an empty string in that case.
It was not immediately clear from the possible call chains whether this
issue is currently actually triggerable or not.
Note that before commit 4843b4b5ec ("xhci: fix even more unsafe memory
usage in xhci tracing") the result effect in the failure case was different
as a static buffer was used here, but the code still worked incorrectly.
Fixes: 90d6d5731d ("xhci: Add tracing for input control context")
Cc: stable@vger.kernel.org
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
commit 4843b4b5ec ("xhci: fix even more unsafe memory usage in xhci tracing")
Link: https://lore.kernel.org/r/20220303110903.1662404-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14073ce951 upstream.
xhci_reset() timeout was increased from 250ms to 10 seconds in order to
give Renesas 720201 xHC enough time to get ready in probe.
xhci_reset() is called with interrupts disabled in other places, and
waiting for 10 seconds there is not acceptable.
Add a timeout parameter to xhci_reset(), and adjust it back to 250ms
when called from xhci_stop() or xhci_shutdown() where interrupts are
disabled, and successful reset isn't that critical.
This solves issues when deactivating host mode on platforms like SM8450.
For now don't change the timeout if xHC is reset in xhci_resume().
No issues are reported for it, and we need the reset to succeed.
Locking around that reset needs to be revisited later.
Additionally change the signed integer timeout parameter in
xhci_handshake() to a u64 to match the timeout value we pass to
readl_poll_timeout_atomic()
Fixes: 22ceac1912 ("xhci: Increase reset timeout for Renesas 720201 host.")
Cc: stable@vger.kernel.org
Reported-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reported-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Tested-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70c05e4cf6 upstream.
A race between system resume and device-initiated resume may result in
runtime PM imbalance on USB2 root hub. If a device-initiated resume
starts and system resume xhci_bus_resume() directs U0 before hub driver
sees the resuming device in RESUME state, device-initiated resume will
not be finished in xhci_handle_usb2_port_link_resume(). In this case,
usb_hcd_end_port_resume() call is missing.
This changes calls usb_hcd_end_port_resume() if resuming device reaches
U0 to keep runtime PM balance.
Fixes: a231ec41e6 ("xhci: refactor U0 link state handling in get_port_status")
Cc: stable@vger.kernel.org
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3105bc977d upstream.
xhci_decode_usbsts() is expected to return a zero-terminated string by
its only caller, xhci_stop_endpoint_command_watchdog(), which directly
logs the return value:
xhci_warn(xhci, "USBSTS:%s\n", xhci_decode_usbsts(str, usbsts));
However, if no recognized bits are set in usbsts, the function will
return without having called any sprintf() and therefore return an
untouched non-zero-terminated caller-provided buffer, causing garbage
to be output to log.
Fix that by always including the raw value in the output.
Note that before commit 4843b4b5ec ("xhci: fix even more unsafe memory
usage in xhci tracing") the result effect in the failure case was different
as a static buffer was used here, but the code still worked incorrectly.
Fixes: 9c1aa36efd ("xhci: Show host status when watchdog triggers and host is assumed dead.")
Cc: stable@vger.kernel.org
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 243a1dd7ba upstream.
The -ENODEV return value from xhci_check_args() is incorrectly changed
to -EINVAL in a couple places before propagated further.
xhci_check_args() returns 4 types of value, -ENODEV, -EINVAL, 1 and 0.
xhci_urb_enqueue and xhci_check_streams_endpoint return -EINVAL if
the return value of xhci_check_args <= 0.
This causes problems for example r8152_submit_rx, calling usb_submit_urb
in drivers/net/usb/r8152.c.
r8152_submit_rx will never get -ENODEV after submiting an urb when xHC
is halted because xhci_urb_enqueue returns -EINVAL in the very beginning.
[commit message and header edit -Mathias]
Fixes: 203a86613f ("xhci: Avoid NULL pointer deref when host dies.")
Cc: stable@vger.kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220215123320.1253947-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e484409258 upstream.
The Fresco Logic FL1100 controller needs the TRUST_TX_LENGTH quirk like
other Fresco controllers, but should not have the BROKEN_MSI quirks set.
BROKEN_MSI quirk causes issues in detecting usb drives connected to docks
with this FL1100 controller.
The BROKEN_MSI flag was apparently accidentally set together with the
TRUST_TX_LENGTH quirk
Original patch went to stable so this should go there as well.
Fixes: ea0f69d821 ("xhci: Enable trust tx length quirk for Fresco FL11 USB controller")
Cc: stable@vger.kernel.org
cc: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211221112825.54690-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7faac1953e upstream.
Make xhci_disable_slot() synchronous, thus ensuring it, and
xhci_free_dev() calling it return after xHC controller completes
the disable slot command.
Otherwise the roothub and xHC host may runtime suspend, and clear the
command ring while the disable slot command is being processed.
This causes a command completion mismatch as the completion event can't
be mapped to the correct command.
Command ring gets out of sync and commands time out.
Driver finally assumes host is unresponsive and bails out.
usb 2-4: USB disconnect, device number 10
xhci_hcd 0000:00:0d.0: ERROR mismatched command completion event
...
xhci_hcd 0000:00:0d.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:0d.0: HC died; cleaning up
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 811ae81320 upstream.
When the xHCI is quirked with XHCI_RESET_ON_RESUME, runtime resume
routine also resets the controller.
This is bad for USB drivers without reset_resume callback, because
there's no subsequent call of usb_dev_complete() ->
usb_resume_complete() to force rebinding the driver to the device. For
instance, btusb device stops working after xHCI controller is runtime
resumed, if the controlled is quirked with XHCI_RESET_ON_RESUME.
So always take XHCI_RESET_ON_RESUME into account to solve the issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09f736aa95 upstream.
Turns out some xHC controllers require all 64 bits in the CRCR register
to be written to execute a command abort.
The lower 32 bits containing the command abort bit is written first.
In case the command ring stops before we write the upper 32 bits then
hardware may use these upper bits to set the commnd ring dequeue pointer.
Solve this by making sure the upper 32 bits contain a valid command
ring dequeue pointer.
The original patch that only wrote the first 32 to stop the ring went
to stable, so this fix should go there as well.
Fixes: ff0e50d356 ("xhci: Fix command ring pointer corruption while aborting a command")
Cc: stable@vger.kernel.org
Tested-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211126122340.1193239-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc153aba3e upstream.
Instead of maintaining a single-linked list of devices that must be
searched linearly in .remove() just use spi_set_drvdata() to remember the
link between the spi device and the driver struct. Then the global list
and the next member can be dropped.
This simplifies the driver, reduces the memory footprint and the time to
search the list. Also it makes obvious that there is always a corresponding
driver struct for a given device in .remove(), so the error path for
!max3421_hcd can be dropped, too.
As a side effect this fixes a data inconsistency when .probe() races with
itself for a second max3421 device in manipulating max3421_hcd_list. A
similar race is fixed in .remove(), too.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211018204028.2914597-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1959faf08 upstream.
Some USB 3.1 enumeration issues were reported after the hub driver removed
the minimum 100ms limit for the power-on-good delay.
Since commit 90d28fb53d ("usb: core: reduce power-on-good delay time of
root hub") the hub driver sets the power-on-delay based on the
bPwrOn2PwrGood value in the hub descriptor.
xhci driver has a 20ms bPwrOn2PwrGood value for both roothubs based
on xhci spec section 5.4.8, but it's clearly not enough for the
USB 3.1 devices, causing enumeration issues.
Tests indicate full 100ms delay is needed.
Reported-by: Walt Jr. Brake <mr.yming81@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fixes: 90d28fb53d ("usb: core: reduce power-on-good delay time of root hub")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211105160036.549516-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The command ring pointer is located at [6:63] bits of the command
ring control register (CRCR). All the control bits like command stop,
abort are located at [0:3] bits. While aborting a command, we read the
CRCR and set the abort bit and write to the CRCR. The read will always
give command ring pointer as all zeros. So we essentially write only
the control bits. Since we split the 64 bit write into two 32 bit writes,
there is a possibility of xHC command ring stopped before the upper
dword (all zeros) is written. If that happens, xHC updates the upper
dword of its internal command ring pointer with all zeros. Next time,
when the command ring is restarted, we see xHC memory access failures.
Fix this issue by only writing to the lower dword of CRCR where all
control bits are located.
Cc: stable@vger.kernel.org
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 5.15-rc5 that resolve a number of
reported issues:
- gadget driver fixes
- xhci build warning fixes
- build configuration fix
- cdc-acm tty handling fixes
- cdc-wdm fix
- typec fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: cdc-acm: fix break reporting
USB: cdc-acm: fix racy tty buffer accesses
usb: gadget: f_uac2: fixed EP-IN wMaxPacketSize
usb: cdc-wdm: Fix check for WWAN
usb: chipidea: ci_hdrc_imx: Also search for 'phys' phandle
usb: typec: tcpm: handle SRC_STARTUP state if cc changes
usb: typec: tcpci: don't handle vSafe0V event if it's not enabled
usb: typec: tipd: Remove dependency on "connector" child fwnode
Partially revert "usb: Kconfig: using select for USB_COMMON dependency"
usb: dwc3: gadget: Revert "set gadgets parent to the right controller"
usb: xhci: tegra: mark PM functions as __maybe_unused
Pull ARM SoC fixes from Arnd Bergmann:
"This is a larger than normal update for Arm SoC specific code, most of
it in device trees, but also drivers and the omap and at91/sama7
platforms:
- There are four new entries to the MAINTAINERS file: Sven Peter and
Alyssa Rosenzweig for Apple M1, Romain Perier for Mstar/sigmastar,
and Vignesh Raghavendra for TI K3
- Build fixes to address randconfig warnings in sharpsl, dove, omap1,
and qcom platforms as well as the scmi and op-tee subsystems
- Regression fixes for missing CONFIG_FB and other options for
several defconfigs
- Several bug fixes for the newly added Microchip SAMA7 platform,
mostly regarding power management
- Missing SMP barriers to protect accesses to SCMI virtio device
- Regression fixes for TI OMAP, including a boot-time hang on am335x.
- Lots of bug fixes for NXP i.MX, mostly addressing incorrect
settings in devicetree files, and one revert for broken suspend.
- Fixes for ARM Juno/Vexpress devicetree files, addressing a couple
of schema warnings.
- Regression fixes for qualcomm SoC specific drivers and devicetree
files, reverting an mdt_loader change and at least pastially
reverting some of the 5.15 DTS changes, plus some minor bugfixes"
* tag 'armsoc-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (64 commits)
MAINTAINERS: Add Sven Peter as ARM/APPLE MACHINE maintainer
MAINTAINERS: Add Alyssa Rosenzweig as M1 reviewer
firmware: arm_scmi: Add proper barriers to scmi virtio device
firmware: arm_scmi: Simplify spinlocks in virtio transport
ARM: dts: omap3430-sdp: Fix NAND device node
bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893
ARM: sharpsl_param: work around -Wstringop-overread warning
ARM: defconfig: gemini: Restore framebuffer
ARM: dove: mark 'putc' as inline
ARM: omap1: move omap15xx local bus handling to usb.c
MAINTAINERS: Add Vignesh to TI K3 platform maintainership
arm64: dts: imx8m*-venice-gw7902: fix M2_RST# gpio
ARM: imx6: disable the GIC CPU interface before calling stby-poweroff sequence
arm64: dts: ls1028a: fix eSDHC2 node
arm64: dts: imx8mm-kontron-n801x-som: do not allow to switch off buck2
ARM: dts: at91: sama7g5ek: to not touch slew-rate for SDMMC pins
ARM: dts: at91: sama7g5ek: use proper slew-rate settings for GMACs
ARM: at91: pm: preload base address of controllers in tlb
ARM: at91: pm: group constants and addresses loading
ARM: dts: at91: sama7g5ek: add suspend voltage for ddr3l rail
...
Commit 38225f2ef2 ("ARM/omap1: switch to use dma_direct_set_offset for
lbus DMA offsets") removed a lot of mach/memory.h, but left the USB
offset handling split into arch/arm/mach-omap1/usb.c and
drivers/usb/host/ohci-omap.c.
This can cause a randconfig build warning that now fails the build
with -Werror:
arch/arm/mach-omap1/usb.c:561:30: error: 'omap_1510_usb_ohci_nb' defined but not used [-Werror=unused-variable]
561 | static struct notifier_block omap_1510_usb_ohci_nb = {
| ^~~~~~~~~~~~~~~~~~~~~
Move it all into the platform file to get rid of the final
location that relies on mach/memory.h.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210927144118.2464881-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The added #ifdefs in the PM rework were almost correct, but still
cause warnings in some randconfig builds:
drivers/usb/host/xhci-tegra.c:2147:12: error: 'tegra_xusb_resume' defined but not used [-Werror=unused-function]
2147 | static int tegra_xusb_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~
drivers/usb/host/xhci-tegra.c:2105:12: error: 'tegra_xusb_suspend' defined but not used [-Werror=unused-function]
2105 | static int tegra_xusb_suspend(struct device *dev)
Replace the #ifdef checks with simpler __maybe_unused annotations to
reliably shut up these warnings.
Link: https://lore.kernel.org/all/20210421135613.3560777-2-arnd@kernel.org/
Fixes: 971ee24706 ("usb: xhci: tegra: Enable ELPG for runtime/system PM")
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211005112057.2700888-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f3de5d857b.
That commit broke USB on all routers that have USB always powered on and
don't require toggling any GPIO. It's a majority of devices actually.
The original code worked and seemed safe: vcc GPIO is optional and
bcma_hci_platform_power_gpio() takes care of checking the pointer before
using it.
This revert fixes:
[ 10.801127] bcma_hcd: probe of bcma0:11 failed with error -2
Fixes: f3de5d857b ("USB: bcma: Add a check for devm_gpiod_get")
Cc: stable <stable@vger.kernel.org>
Cc: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20210831065419.18371-1-zajec5@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use platform_register_drivers() and platform_unregister_drivers() to
register and unregister ehci platform drivers. This simplifies the code
and prevents the following build errors seen with sparc:allmodconfig.
drivers/usb/host/ehci-hcd.c:1301: error:
"PLATFORM_DRIVER" redefined
drivers/usb/host/ehci-sh.c:173:31: error:
'ehci_hcd_sh_driver' defined but not used
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210907123002.3951446-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt patches for 5.15-rc1.
Nothing huge in here, just lots of constant forward progress on a
number of different drivers and hardware support:
- more USB 4/Thunderbolt support added
- dwc3 driver updates and additions
- usb gadget fixes and addtions for new types
- udc gadget driver updates
- host controller updates
- removal of obsolete drivers
- other minor driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (148 commits)
usb: isp1760: otg control register access
usb: isp1760: use the right irq status bit
usb: isp1760: write to status and address register
usb: isp1760: fix qtd fill length
usb: isp1760: fix memory pool initialization
usb: typec: tcpm: Fix spelling mistake "atleast" -> "at least"
usb: dwc2: Fix spelling mistake "was't" -> "wasn't"
usb: renesas_usbhs: Fix spelling mistake "faile" -> "failed"
usb: host: xhci-rcar: Don't reload firmware after the completion
usb: xhci-mtk: allow bandwidth table rollover
usb: mtu3: fix random remote wakeup
usb: mtu3: return successful suspend status
usb: xhci-mtk: Do not use xhci's virt_dev in drop_endpoint
usb: xhci-mtk: modify the SOF/ITP interval for mt8195
usb: xhci-mtk: add a member of num_esit
usb: xhci-mtk: check boundary before check tt
usb: xhci-mtk: update fs bus bandwidth by bw_budget_table
usb: xhci-mtk: fix issue of out-of-bounds array access
usb: xhci-mtk: support option to disable usb2 ports
usb: xhci-mtk: fix use-after-free of mtk->hcd
...
Pull tty / serial updates from Greg KH:
"Here is the "big" set of tty/serial driver patches for 5.15-rc1
Nothing major in here at all, just some driver updates and more
cleanups on old tty apis and code that needed it that includes:
- tty.h cleanup of things that didn't belong in it
- other tty cleanups by Jiri
- driver cleanups
- rs485 support added to amba-pl011 driver
- dts updates
- stm32 serial driver updates
- other minor fixes and driver updates
All have been in linux-next for a while with no reported problems"
* tag 'tty-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (83 commits)
tty: serial: uartlite: Use read_poll_timeout for a polling loop
tty: serial: uartlite: Use constants in early_uartlite_putc
tty: Fix data race between tiocsti() and flush_to_ldisc()
serial: vt8500: Use of_device_get_match_data
serial: tegra: Use of_device_get_match_data
serial: 8250_ingenic: Use of_device_get_match_data
tty: serial: linflexuart: Remove redundant check to simplify the code
tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp
tty: serial: fsl_lpuart: enable two stop bits for lpuart32
tty: serial: fsl_lpuart: fix the wrong mapbase value
mxser: use semi-colons instead of commas
tty: moxa: use semi-colons instead of commas
tty: serial: fsl_lpuart: check dma_tx_in_progress in tx dma callback
tty: replace in_irq() with in_hardirq()
serial: sh-sci: fix break handling for sysrq
serial: stm32: use devm_platform_get_and_ioremap_resource()
serial: stm32: use the defined variable to simplify code
Revert "arm pl011 serial: support multi-irq request"
tty: serial: samsung: Add Exynos850 SoC data
tty: serial: samsung: Fix driver data macros style
...
xhci-mtk has 64 slots for periodic bandwidth calculations and each
slot represents byte budgets on a microframe. When an endpoint's
allocation sits on the boundary of the table, byte budgets' slot
can be rolled over but the current implementation doesn't.
This patch allows the microframe index rollover and prevent
out-of-bounds array access.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210827033105.26595-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent attempt to handle an unknown ROM state in the commit
d143825baf ("usb: renesas-xhci: Fix handling of unknown ROM state")
resulted in a regression and reverted later by the commit 44cf53602f
("Revert "usb: renesas-xhci: Fix handling of unknown ROM state"").
The problem of the former fix was that it treated the failure of
firmware loading as a fatal error. Since the firmware files aren't
included in the standard linux-firmware tree, most users don't have
them, hence they got the non-working system after that. The revert
fixed the regression, but also it didn't make the firmware loading
triggered even on the devices that do need it. So we need still a fix
for them.
This is another attempt to handle the unknown ROM state. Like the
previous fix, this also tries to load the firmware when ROM shows
unknown state. In this patch, however, the failure of a firmware
loading (such as a missing firmware file) isn't handled as a fatal
error any longer when ROM has been already detected, but it falls back
to the ROM mode like before. The error is returned only when no ROM
is detected and the firmware loading failed.
Along with it, for simplifying the code flow, the detection and the
check of ROM is factored out from renesas_fw_check_running() and done
in the caller side, renesas_xhci_check_request_fw(). It avoids the
redundant ROM checks.
The patch was tested on Lenovo Thinkpad T14 gen (BIOS 1.34). Also it
was confirmed that no regression is seen on another Thinkpad T14
machine that has worked without the patch, too.
Fixes: 44cf53602f ("Revert "usb: renesas-xhci: Fix handling of unknown ROM state"")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1189207
Link: https://lore.kernel.org/r/20210826124127.14789-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci-mtk depends on xhci's internal virt_dev when it retrieves its
internal data from usb_host_endpoint both in add_endpoint and
drop_endpoint callbacks. But when setup packet was retired by
transaction errors in xhci_setup_device() path, a virt_dev for the slot
is newly created with real_port 0. This leads to xhci-mtks's NULL pointer
dereference from drop_endpoint callback as xhci-mtk assumes that virt_dev's
real_port is always started from one. The similar problems were addressed
by [1] but that can't cover the failure cases from setup_device.
This patch drops the usages of xhci's virt_dev in xhci-mtk's drop_endpoint
callback by adopting hashtable for searching mtk's schedule entity
from a given usb_host_endpoint pointer instead of searching a linked list.
So mtk's drop_endpoint callback doesn't have to rely on virt_dev at all.
[1] f351f4b63d ("usb: xhci-mtk: fix oops when unbind driver")
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210826025144.51992-5-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
