Use watchdog_stop_on_reboot() to stop the watchdog on reboot instead
of registering a driver-specific notifier.
While at it, reorder remaining include files alphabetically.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Resetting the watchdog timer on CIR interrupts or on game port interrupts
is not not supported on recent chips, and doesn't really tell if the system
is stable. On top of that, at least the bit to enable resetting the
watchdog through the game port is used differently on recent chips.
Drop resetting the watchdog on CIR or game port interrupts to simplify
the code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The dw_wdt has an external reset line, that can keep the device in reset
and therefore rendering it useless and also is the only way of stopping
the watchdog once it was started.
Get the reset lines for this core from the devicetree. As these lines are
optional, use devm_reset_control_get_optional_shared. If the reset line
is not specified in the devicetree, the reset framework will just skip
deasserting and continue.
This way all users of the driver will continue to function without
any harm, even if the reset line is not specified in the devicetree.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The CDC-NCM driver can require large amounts of memory to create
skb's and this can be a problem when the memory becomes fragmented.
This especially affects embedded systems that have constrained
resources but wish to maximise the throughput of CDC-NCM with 16KiB
NTB's.
The issue is after running for a while the kernel memory can become
fragmented and it needs compacting.
If the NTB allocation is needed before the memory has been compacted
the atomic allocation can fail which can cause increased latency,
large re-transmissions or disconnections depending upon the data
being transmitted at the time.
This situation occurs for less than a second until the kernel has
compacted the memory but the failed devices can take a lot longer to
recover from the failed TX packets.
To ease this temporary situation I modified the CDC-NCM TX path to
temporarily switch into a reduced memory mode which allocates an NTB
that will fit into a USB_CDC_NCM_NTB_MIN_OUT_SIZE (default 2048 Bytes)
sized memory block and only transmit NTB's with a single network frame
until the memory situation is resolved.
Each time this issue occurs we wait for an increasing number of
reduced size allocations before requesting a full size one to not
put additional pressure on a low memory system.
Once the memory is compacted the CDC-NCM data can resume transmitting
at the normal tx_max rate once again.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch takes care of active/passive disconnect flows.
Disconnect flows can be initiated remotely, in which case a async event
will arrive from peer and indicated to qedr driver. These
are referred to as exceptions. When a QP is destroyed, it needs to check
that it's associated ep has been closed.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the active side connect.
Offload a connection, process MPA reply and send RTR.
In some of the common passive/active functions, the active side
will work in blocking mode.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the passive side connect.
It addresses pre-allocating resources, creating a connection
element upon valid SYN packet received. Calling upper layer and
implementation of the accept/reject calls.
Error handling is not part of this patch.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ability to add and remove listeners and identify
whether the SYN packet received is intended for iWARP or not. If
a listener is not found the SYN packet is posted back to the chip.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP handles incoming SYN packets using the ll2 interface. This patch
implements ll2 setup and teardown. Additional ll2 connections will
be used in the future which are not part of this patch series.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds iWARP support for flows that have common code
between RoCE and iWARP, such as initialization, teardown and
qp setup verbs: create, destroy, modify, query.
It introduces the iWARP specific files qed_iwarp.[ch] and
iwarp_common.h
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP personality introduced the need for differentiating in several
places in the code whether we are RoCE, iWARP or either. This
leads to introducing new macros for querying the personality.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements the setup of RS232 and the switch-over to RS485 or RS422
for the Siemens IOT2040. That uses an EXAR XR17V352 with external logic
to switch between the different modes. The external logic is controlled
via MPIO pins of the EXAR controller.
Only pin 10 can be exported as GPIO on the IOT2040. It is connected to
an LED.
As the XR17V352 used on the IOT2040 is not equipped with an external
EEPROM, it cannot present itself as IOT2040-variant via subvendor/
subdevice IDs. Thus, we have to check via DMI for the target platform.
Co-developed with Sascha Weisenberger.
Signed-off-by: Sascha Weisenberger <sascha.weisenberger@siemens.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the SIMATIC, IOT2040 only a single pin is exportable as GPIO, the
rest is required to operate the UART. To allow modeling this case,
expand the platform device data structure to specify a (consecutive) pin
subset for exporting by the gpio-exar driver.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Set the parent of the exar gpiochip to its platform device, like other
gpiochips are doing it. In order to keep the relationship discoverable
for ACPI systems, set the platform device companion to the PCI device.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Commtech adapters need the MPIOs for internal purposes, and the
gpio-exar driver already refused to pick them up. But there is actually
no point in even creating the underlying platform device.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current code is violating the DMA Engine API by putting the submitted
requests directly into the HW queue. This causes queued transactions
to be started by another thread as soon as the first one finishes.
The DMA Engine document clearly states this.
"dmaengine_submit() will not start the DMA operation".
Move HW queuing of the requests into the issue_pending() routine
to comply with API requirements also create a new queued state for
temporarily holding the requests.
A descriptor goes through these transitions now.
free->prepared->queued->active->completed->free
as opposed to
free->prepared->active->completed->free
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Remove check for "len > ZYNQMP_DMA_MAX_TRANS_LEN" as its not needed.
If the length is larger, the transfer is split up into multiple parts
with the max descriptor length already.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Kedareswara rao Appana <appanad@xilinx.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* pci/resource:
PCI: Work around poweroff & suspend-to-RAM issue on Macbook Pro 11
PCI: Do not disregard parent resources starting at 0x0
Conflicts:
arch/x86/pci/fixup.c
* pci/portdrv:
PCI/portdrv: Allocate MSI/MSI-X vector for Downstream Port Containment
PCI/portdrv: Support multiple interrupts for MSI as well as MSI-X
* pci/pm:
PCI/PM: Avoid using device_may_wakeup() for runtime PM
x86/PCI: Avoid AMD SB7xx EHCI USB wakeup defect
PCI/PM: Restore the status of PCI devices across hibernation
drm/radeon: make MacBook Pro d3_delay quirk more generic
drm/amdgpu: remove unnecessary save/restore of pdev->d3_delay
PCI/PM: Add needs_resume flag to avoid suspend complete optimization
PCI: imx6: Fix config read timeout handling
switchtec: Fix minor bug with partition ID register
switchtec: Use new cdev_device_add() helper function
PCI: endpoint: Make PCI_ENDPOINT depend on HAS_DMA
* pci/enumeration:
PCI: Enable ECRC only if device supports it
PCI: Add sysfs max_link_speed/width, current_link_speed/width, etc
PCI: Test INTx masking during enumeration, not at run-time
of_device_ids are not supposed to change at runtime. All functions working
with of_device_ids provided by <linux/of.h> work with const of_device_ids.
So mark the non-const structs as const.
File size before:
text data bss dec hex filename
195 600 0 795 31b drivers/pci/host/pcie-xilinx.o
File size after constify xilinx_pcie_of_match:
text data bss dec hex filename
595 184 0 779 30b drivers/pci/host/pcie-xilinx.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Add spinlock for protecting legacy mask register
- Few wifi end points which only support legacy interrupts, performs
hardware reset functionalities after disabling interrupts by invoking
disable_irq() and then re-enable using enable_irq(), they enable hardware
interrupts first and then virtual IRQ line later.
- The legacy IRQ line goes low only after DEASSERT_INTx is received. As
the legacy IRQ line is high immediately after hardware interrupts are
enabled but virq of EP is still in disabled state and EP handler is never
executed resulting no DEASSERT_INTx. If dummy IRQ chip is used,
interrupts are not masked and system hangs with CPU stall.
- Add IRQ chip functions instead of dummy IRQ chip for legacy interrupts.
- Legacy interrupts are level sensitive, so using handle_level_irq() is
more appropriate as it is masks interrupts until Endpoint handles
interrupts and unmasks interrupts after Endpoint handler is executed.
- Legacy interrupts are level triggered, virtual IRQ line of EndPoint shows
as edge in /proc/interrupts.
- Set IRQ flags of virtual IRQ line of EP to level triggered at the time of
mapping.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Recent __call_srcu() changes have exposed that we need to cleanup SRCU
structures after pci_stop_root_bus() calls into vmd_msi_free().
Fixes: 3906b91844 ("PCI: vmd: Use SRCU as a local RCU to prevent delaying global RCU")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Cc: <stable@vger.kernel.org> # 4.11
VMD domains are allocated starting at 0x10000, not 0x1000 as the comment
said. Correct the comment and add a reference to the ACPI spec for _SEG.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI host bridge found on Tegra SoCs doesn't require the MSI target
address to be backed by physical system memory. Writes are intercepted
within the controller and never make it to the memory pointed to.
Since no actual system memory is required, remove the allocation of a
single page and hardcode the MSI target address with a special address that
maps to the last 4 KiB page within the range that is reserved for system
memory and memory-mapped I/O in the FPCI address map.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
The MSI target address can reside beyond the 32-bit boundary on devices
with more than 2 GiB of system memory. The PCI host bridge on Tegra can
easily support 64-bit addresses, so make sure to pass the upper 32 bits of
the target address to endpoints when allocating MSI entries.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
We have a local "struct device *dev" in rockchip_pcie_probe(). Use it
consistently throughout the function. No functional change intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The default value of MPS for RC is 128 bytes, but actually it could support
256 bytes. So this patch fixes this issue.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe base specification (Revision 3.1a), section 7.5.3, type 1
configuration space header should be used when accessing PCIe switch. So
we need to reconfigure the header according to the bus number we are
accessing. Otherwise we could not visit the buses behind the switch.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We need to reconfigure the header type later, so split out a new function.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Configuration accesses is also part of ATU settings, so let's keep all of
them inside rockchip_pcie_cfg_atu().
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename rockchip_cfg_atu() to keep the name consistent with other functions
in pcie-rockchip.c.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
