The mac power-on flow consists of three steps:
1. pre_sys_cfg (Before switching power state)
2. power_switch (Switching power state)
3. init_sys_cfg (Settings after swtiching power state)
When switching power state, driver will load and parse the power sequence
tables. For 8723D devices, the logics for parsing are most same except for
the polling function. 8723D devices need to toggle BIT_PFM_WOWL twice.
The settings after power state is switched for 8723D devices are quite
different with other devices, extract a legacy function for them.
For power-off flow, 8723D devices have the same logic with existing chips.
But warning printed if we run power-off sequence in power-off state:
rtw_pci 0000:03:00.0: failed to poll offset=0x5f8 mask=0xff value=0x0
The scenario is user do 'ifconfig up' that will run power-on sequence to
bring up and then run power-off sequence to enter idle
(IEEE80211_CONF_IDLE). Then, user do 'ifconfig down' that will run
power-off sequence again, and the warning is shown. Original code check
power-on state to avoid to run power-on sequence twice, and this commit
extends to check both power-on and power-off states.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422034607.28747-4-yhchuang@realtek.com
The WLAN CPU of 8723D device is different from others, add legacy
firmware download function for it. A new variable wlan_cpu is used to
decide which firmware download function we should use.
Legacy firmware file contains 32 bytes header including version and
subversion. When downloading to wlan cpu, header is excluded.
Firmware is downloaded via beacon queue to reserved page that is a part of
TX buffer. Since 11N WLAN CPU uses different control registers, this patch
introduces related control registers.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422034607.28747-2-yhchuang@realtek.com
8723D use SIPI to indirectly read RF register instead of directly read,
so introduce a new struct rtw_rf_sipi_addr and new function
rtw_phy_read_rf_sipi(). Since other chips don't use the new function,
only 8723D needs to fill struct rtw_rf_sipi_addr in rtw_chip_info.
Because there are two kinds of functions for reading RF registers now,
change rtw_phy_read_rf() to chip->ops->read_rf() in
rtw_phy_write_rf_reg_sipi() so that we can switch tp proper RF read
functions depends on the type of the chip.
Though 8723D is an 1x1 chip, it has two RF PHY and we can switch to
one of them, and that should be configured properly. Hence, add a
fix_rf_phy_num to struct rtw_chip_info to allow driver to set one of
the PHY's registers for 8723D, even it is only 1x1. Another variable
rf_phy_num is introduced to keep the constraint number of RF path we
can access, and its value is:
rf_phy_num = (fix_rf_phy_num ? fix_rf_phy_num : rf_path_num)
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420055054.14592-5-yhchuang@realtek.com
8723D doesn't support beamform because rtw88 only supports VHT beamform
but 8723d doesn't have VHT capability. Though 8723d doesn't support
beamform, BSS_CHANGED_MU_GROUPS is still marked as changed when doing
disassociation. So, add wrapper functions for all beamform ops to make
sure they aren't NULL before calling.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420055054.14592-3-yhchuang@realtek.com
Fix the following coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hw.c:617:14-20: WARNING:
Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hw.c:622:13-19: WARNING:
Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hw.c:627:14-20: WARNING:
Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hw.c:632:13-19: WARNING:
Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hw.c:937:5-13: WARNING:
Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420042658.18733-1-yanaijie@huawei.com
This function actually needs no return value. So remove the unneeded
variable 'ret' and make it void.
This also fixes the following coccicheck warning:
drivers/net/wireless/intel/ipw2x00/ipw2200.c:10648:5-8: Unneeded
variable: "ret". Return "0" on line 10684
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200414120251.35869-1-yanaijie@huawei.com
Sparse reports warnings at prism2_bss_list_proc_start() and prism2_bss_list_proc_stop()
warning: context imbalance in prism2_wds_proc_stop() - unexpected unlock
warning: context imbalance in prism2_bss_list_proc_start() - wrong count at exit
The root cause is the missing annotations at prism2_bss_list_proc_start()
Add the missing __acquires(&local->lock) annotation
Add the missing __releases(&local->lock) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200411001933.10072-4-jbi.octave@gmail.com
To support ieee80211_ops::set_antenna, the driver can decide if the
antenna mask is accepted, otherwise it can return an error code.
Because each chip could have different limitations, let the chip
check the mask and return.
Also the antenna mask for TRX from upper space is 32-bit long.
Change the antenna mask for rtw_chip_ops::set_antenna from u8 to u32.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200410100950.3199-2-yhchuang@realtek.com
This patch fixes commit 75388acd0c ("add mac80211-based driver for
legacy BCM43xx devices")
In https://bugzilla.kernel.org/show_bug.cgi?id=207093, a defect in
b43legacy is reported. Upon testing, thus problem exists on PPC and
X86 platforms, is present in the oldest kernel tested (3.2), and
has been present in the driver since it was first added to the kernel.
The problem is a corrupted channel status received from the device.
Both the internal card in a PowerBook G4 and the PCMCIA version
(Broadcom BCM4306 with PCI ID 14e4:4320) have the problem. Only Rev, 2
(revision 4 of the 802.11 core) of the chip has been tested. No other
devices using b43legacy are available for testing.
Various sources of the problem were considered. Buffer overrun and
other sources of corruption within the driver were rejected because
the faulty channel status is always the same, not a random value.
It was concluded that the faulty data is coming from the device, probably
due to a firmware bug. As that source is not available, the driver
must take appropriate action to recover.
At present, the driver reports the error, and them continues to process
the bad packet. This is believed that to be a mistake, and the correct
action is to drop the correpted packet.
Fixes: 75388acd0c ("add mac80211-based driver for legacy BCM43xx devices")
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-and-tested by: F. Erhard <erhard_f@mailbox.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200407190043.1686-1-Larry.Finger@lwfinger.net
Fix sparse warnings:
drivers/net/wireless/realtek/rtw88/fw.c:633:4: warning:
symbol 'rtw_get_rsvd_page_probe_req_location' was not declared. Should it be static?
drivers/net/wireless/realtek/rtw88/fw.c:650:5: warning:
symbol 'rtw_get_rsvd_page_probe_req_size' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200328030524.16032-1-yuehaibing@huawei.com
During RX, accessing the reo dest ring descriptor directly is consuming
a lot of CPU cycles. Accessing the descriptor after copying it locally
has improved CPU usage by around ~10-15% while measuring throughput
in RX DBTC test cases(all radios are involved in the throughput
measurement).
HW tested: IPQ8074
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586421797-885-1-git-send-email-mpubbise@codeaurora.org
Add the pdev index information in the peer object to validate
the peer creation. Ignore the peer creation request, if the given
MAC address is already present in the peer list with same radio.
If we allow the peer creation in above scenario, FW assert will happen.
Above scenario occurred in two cases, where Multiple AP VAP created in
the same radio.
1. when testing tool sends association request to two AP with same
MAC address
2. when a station do roaming from one AP VAP to another AP VAP.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586343795-21422-1-git-send-email-periyasa@codeaurora.org
This sorts the actual field names too, potentially causing even more
chaos and confusion at merge time if you have edited the MAINTAINERS
file. But the end result is a more consistent layout, and hopefully
it's a one-time pain minimized by doing this just before the -rc1
release.
This was entirely scripted:
./scripts/parse-maintainers.pl --input=MAINTAINERS --output=MAINTAINERS --order
Requested-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
