Besides other potential problems, if MPIC_NO_RESET is not set,
the error interrupt will be masked after it is requested.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add support for T104x board in board file t104x_qds.c, It is common for
both T1040 and T1042 as they share same QDS board.
T1040QDS board Overview
-----------------------
- SERDES Connections, 8 lanes supporting:
— PCI Express: supporting Gen 1 and Gen 2;
— SGMII
— QSGMII
— SATA 2.0
— Aurora debug with dedicated connectors (T1040 only)
- DDR Controller
- Supports rates of up to 1600 MHz data-rate
- Supports one DDR3LP UDIMM/RDIMMs, of single-, dual- or quad-rank types.
-IFC/Local Bus
- NAND flash: 8-bit, async, up to 2GB.
- NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
- GASIC: Simple (minimal) target within Qixis FPGA
- PromJET rapid memory download support
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep (T1040 only)
- QIXIS System Logic FPGA
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- Video
- DIU supports video at up to 1280x1024x32bpp
- USB
- Supports two USB 2.0 ports with integrated PHYs
— Two type A ports with 5V@1.5A per port.
— Second port can be converted to OTG mini-AB
- SDHC
- SDHC port connects directly to an adapter card slot, featuring:
- Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC
— Supporting eMMC memory devices
- SPI
- On-board support of 3 different devices and sizes
- Other IO
- Two Serial ports
- ProfiBus port
- Four I2C ports
Add T104xQDS support in Kconfig and Makefile. Also create device tree.
Following features are currently not implmented.
- SerDes: Aurora
- IFC: GASIC, Promjet
- QIXIS
- Ethernet
- DIU
- power supplies management
- ProfiBus
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA
processor cores with high-performance data path acceleration architecture
and network peripheral interfaces required for networking & telecommunications.
T1042 personality is a reduced personality of T1040 without Integrated 8-port
Gigabit Ethernet switch.
The T1040/T1042 SoC includes the following function and features:
- Four e5500 cores, each with a private 256 KB L2 cache
- 256 KB shared L3 CoreNet platform cache (CPC)
- Interconnect CoreNet platform
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
for the following functions:
- Packet parsing, classification, and distribution
- Queue management for scheduling, packet sequencing, and congestion
management
- Cryptography Acceleration (SEC 5.0)
- RegEx Pattern Matching Acceleration (PME 2.2)
- IEEE Std 1588 support
- Hardware buffer management for buffer allocation and deallocation
- Ethernet interfaces
- Integrated 8-port Gigabit Ethernet switch (T1040 only)
- Four 1 Gbps Ethernet controllers
- Two RGMII interfaces or one RGMII and one MII interfaces
- High speed peripheral interfaces
- Four PCI Express 2.0 controllers running at up to 5 GHz
- Two SATA controllers supporting 1.5 and 3.0 Gb/s operation
- Upto two QSGMII interface
- Upto six SGMII interface supporting 1000 Mbps
- One SGMII interface supporting upto 2500 Mbps
- Additional peripheral interfaces
- Two USB 2.0 controllers with integrated PHY
- SD/eSDHC/eMMC
- eSPI controller
- Four I2C controllers
- Four UARTs
- Four GPIO controllers
- Integrated flash controller (IFC)
- Change this to LCD/ HDMI interface (DIU) with 12 bit dual data rate
- TDM interface
- Multicore programmable interrupt controller (PIC)
- Two 8-channel DMA engines
- Single source clocking implementation
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The CoreNet coherency fabric is a fabric-oriented, conectivity
infrastructure that enables the implementation of coherent, multicore
systems. The CCF acts as a central interconnect for cores,
platform-level caches, memory subsystem, peripheral devices and I/O host
bridges in the system.
Signed-off-by: Diana Craciun <Diana.Craciun@freescale.com>
[scottwood@freescale.com: formatting and minor changes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
This warning can be seen in allyesconfig, and was introduced by commit
f9eb581c63b2acce827570e105205c0789360650 "powerpc: fix build of
epapr_paravirt on 64-bit book3s".
Signed-off-by: Scott Wood <scottwood@freescale.com>
This fixes an allyesconfig build break introduced by commit
7762b1ed7aaee223230793fcee80672e2e3aa7a8 "powerpc: move epapr paravirt
init of power_save to an initcall".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Stuart Yoder <stuart.yoder@freescale.com>
Main changs include:
- Clarified the clock nodes' version number
- Fixed a issue in example
Singed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
some restructuring of epapr paravirt init resulted in
ppc_md.power_save being set, and then overwritten to
NULL during machine_init. This patch splits the
initialization of ppc_md.power_save out into a postcore
init call.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch introduces the support for Keymile's kmcoge4 board which is
the internal reference design for boards based on Freescale's
P2040/P2041 SoCs. This internal reference design is named kmp204x.
The peripherals used on this board are:
- SPI NOR Flash as bootloader medium
- NAND Flash with a ubi partition
- 2 PCIe busses (hosts 1 and 3)
- 3 FMAN Ethernet devices (FMAN1 DTSEC1/2/5)
- 4 Local Bus windows, with one dedicated to the QRIO reset/power mgmt
CPLD
- 2 I2C busses
- last but not least, the mandatory serial port
The patch also adds a defconfig file for this reference design that is
necessary because of the lowmem option that must be set higher due to
the number of PCIe devices with big ioremapped mem ranges on the boad.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
These are the bindings for 2 MFD devices used on some of the Keymile boards.
The first one is the chassis managmenet bfticu FPGA.
The second one is the board controller (reset, LEDs, GPIOs) QRIO CPDL.
These FPGAs are used in the kmcoge4 board.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Even though the company belongs to Microsemi, many chips are still
labeled as Zarlink. Among them is the family of network clock generators,
the zl3034x.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
PCI controller disable PME message report feature, that shouldn't
have happened. Fix it and enable PME message report feature.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
There are error parameters should be corrected when
calling dma_free_coherent to free rmu rx-ring buffers
in fsl_open_inb_mbox() function.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The only way Freescale booke chips support mappings larger than 4K
is via TLB1. The only way we support (direct) TLB1 entries is via
hugetlb, which is not what map_kernel_page() does when given a large
page size.
Without this, a kernel with CONFIG_SPARSEMEM_VMEMMAP enabled crashes on
boot with messages such as:
PID hash table entries: 4096 (order: 3, 32768 bytes)
Sorting __ex_table...
BUG: Bad page state in process swapper pfn:00a2f
page:8000040000023a48 count:0 mapcount:0 mapping:0000040000ffce48 index:0x40000ffbe50
page flags: 0x40000ffda40(active|arch_1|private|private_2|head|tail|swapcache|mappedtodisk|reclaim|swapbacked|unevictable|mlocked)
page dumped because: PAGE_FLAGS_CHECK_AT_FREE flag(s) set
bad because of flags:
page flags: 0x311840(active|private|private_2|swapcache|unevictable|mlocked)
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 3.15.0-rc1-00003-g7fa250c #299
Call Trace:
[c00000000098ba20] [c000000000008b3c] .show_stack+0x7c/0x1cc (unreliable)
[c00000000098baf0] [c00000000060aa50] .dump_stack+0x88/0xb4
[c00000000098bb70] [c0000000000c0468] .bad_page+0x144/0x1a0
[c00000000098bc10] [c0000000000c0628] .free_pages_prepare+0x164/0x17c
[c00000000098bcc0] [c0000000000c24cc] .free_hot_cold_page+0x48/0x214
[c00000000098bd60] [c00000000086c318] .free_all_bootmem+0x1fc/0x354
[c00000000098be70] [c00000000085da84] .mem_init+0xac/0xdc
[c00000000098bef0] [c0000000008547b0] .start_kernel+0x21c/0x4d4
[c00000000098bf90] [c000000000000448] .start_here_common+0x20/0x58
Signed-off-by: Scott Wood <scottwood@freescale.com>
Two issues:
o For beql_op, beql_op, bne_op, bnel_op, blez_op, blezl_op, bgtz_op and
bgtzl_op the wrong field was being checked for the instruction opcode.
o For blez_op / blezl_op and bgtz_op / bgtzl_op the test was testing
for the wrong opcode.
This bug got introduced by d8d4e3ae0b [MIPS
Kprobes: Refactor branch emulation].
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Acked-by: Victor Kamensky <kamensky@cisco.com>
The way the driver core is implemented, every device using the same bus
type is required to have a unique name because a symlink to each device
is created in the appropriate /sys/bus/*/devices directory, and two
identical names causes a collision.
The current code handles the requirement by using an globally
incremented counter that is appended to the device name. It works, but
it means any change to device registration will change the assigned
numbers. Instead, if we build up the name by using information from the
parent nodes, then it can be guaranteed to be unique without adding a
random number to the end of it.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Cc: Rob Herring <robh@kernel.org>
This patch adds of_clk_get_by_clkspec() helper function, which does only
a struct clk lookup from the clock providers. It is used in the subsequent
patch where parsing of a clock from device tree and the lookup from
providers needed to be split.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The recent change in sysfs, bcdde7e221
"sysfs: make __sysfs_remove_dir() recursive" revealed an asymmetric
rphy device creation/deletion sequence in scsi_transport_sas:
modprobe mpt2sas
sas_rphy_add
device_add A rphy->dev
device_add B sas_device transport class
device_add C sas_end_device transport class
device_add D bsg class
rmmod mpt2sas
sas_rphy_delete
sas_rphy_remove
device_del B
device_del C
device_del A
sysfs_remove_group recursive sysfs dir removal
sas_rphy_free
device_del D warning
where device A is the parent of B, C, and D.
When sas_rphy_free tries to unregister the bsg request queue (device D
above), the ensuing sysfs cleanup discovers that its sysfs group has
already been removed and emits a warning, "sysfs group... not found for
kobject 'end_device-X:0'".
Since bsg creation is a side effect of sas_rphy_add, move its
complementary removal call into sas_rphy_remove. This imposes the
following tear-down order for the devices above: D, B, C, A.
Note the sas_device and sas_end_device transport class devices (B and C
above) are created and destroyed both via the list match traversal in
attribute_container_device_trigger, so the order in which they are
handled is fixed. This is fine as long as they are deleted before their
parent device.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the support for the PRCM muxer on the A31 has been added, the global
static pinctl_desc definition has been left as is. Unfortunately, this
structure is used to register the pinctrl device, and prior to this
registration, we set the name and pins field.
Since this structure is shared across instances, that means that the latest
registered pinctrl device wins in setting the name, pins and pins numbers,
which is not really a good thing.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the following configuration error:
drivers/pinctrl/sunxi/Kconfig:3:error: recursive dependency detected!
drivers/pinctrl/sunxi/Kconfig:3: symbol PINCTRL_SUNXI is selected by PINCTRL_SUN4I_A10
drivers/pinctrl/sunxi/Kconfig:9: symbol PINCTRL_SUN4I_A10 default value contains PINCTRL_SUNXI
Add a new intermedia PINCTRL_SUNXI_COMMON, that superseeds the PINCTRL_SUNXI
one.
We still need to keep PINCTRL_SUNXI at the moment in order to preserve
bisectability. Indeed, during that merge window, we also introduced the
MACH_SUN* symbols. Since it's going through different trees, we can't rely on
the fact that the options will be there, while ARCH_SUNXI still select
PINCTRL_SUNXI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pin-controller driver for the Berlin BG2Q SoC, with definition
of its groups and functions. Pin control registers are part of chip/
system control registers, which will be represented by a single node.
Until a proper driver for the chip/system control is available,
register the corresponding regmap in pinctrl driver probe.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pin-controller driver for the Berlin BG2 SoC, with definition
of its groups and functions. Pin control registers are part of chip/
system control registers, which will be represented by a single node.
Until a proper driver for the chip/system control is available,
register the corresponding regmap in pinctrl driver probe.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pin-controller driver for the Berlin BG2Q SoC, with definition
of its groups and functions. Pin control registers are part of chip/
system control registers, which will be represented by a single node.
Until a proper driver for the chip/system control is available,
register the corresponding regmap in pinctrl driver probe.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Marvell Berlin boards have a group based pinmuxing mechanism. This
adds the core driver support. We actually do not need any information
about the pins here and only have the definition of the groups.
Let's take the example of the uart0 pinmuxing on the BG2Q. Balls BK4 and
BH6 are muxed to respectively UART0 RX and TX if the group GSM12 is set
to mode 0:
Group Modes Offset Base Offset LSB Bit Width
GSM12 3 sm_base 0x40 0x10 0x2
Ball Group Mode 0 Mode 1 Mode 2
BK4 GSM12 UART0_RX IrDA0_RX GPIO9
BH6 GSM12 UART0_TX IrDA0_TX GPIO10
So in order to configure BK4 -> UART0_TX and BH6 -> UART0_RX, we need
to set (sm_base + 0x40 + 0x10) &= ff3fffff.
As pin control registers are part of either chip control or system
control registers, that deal with a bunch of other functions we rely
on a regmap instead of exclusively remapping any resources.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If chip->to_irq is NULL ACPI GPIO helpers don't register GPIO event
handlers thus preventing any ACPI GPIO triggered events. Solve this by
calling gpiochip_add() after we have set up drivers chip->to_irq hook.
Signed-off-by: Jin Yao <yao.jin@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the multiplatform kernel case the IRQs associated with the PFC GPIOs
are specified through DT. The pinmux_irq irq field is thus ignored by
the code, and doesn't need to be set.
This will allow removing the mach/irq.h include from pfc-*.c files that
was required for the irq_pin() macro used to initialize the irq field.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Enable the freshly introduced Kconfig options whenever their matching
architecture is enabled.
Since the Kconfig symbols for these machines are going through a different
tree, keep PINCTRL_SUNXI around for the moment to avoid breaking the defconfig.
It should be removed eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the 2 SDHC controllers on the DB8074 board. The first
controller (at 0xf9824900) is connected to an on board soldered eMMC.
The second controller (at 0xf98a4900) is connected to a uSD card slot.
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Current code only touches the direction register when setting direction
to output, which breaks logic like
echo high > /sys/class/gpio/gpio0/direction
which is expected to also set the value. This patch also adds a call
to update the value register when setting direction to output.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SoCFPGA has two watchdog timers. Add them to the dtsi.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
[dinh: modified patch to have correct irq flag]
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Up until now, contexts had one (and only one) backing object that was
used by the hardware to save/restore render ring contexts (via the
MI_SET_CONTEXT command). Other rings did not have or need this, so
our i915_hw_context struct had a 1:1 relationship with a a real HW
context.
With Logical Ring Contexts and Execlists, this is not possible anymore:
all rings need a backing object, and it cannot be reused. To prepare
for that, rename our contexts to the more generic term intel_context.
No functional changes.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The cycloneV has three gpio controllers, each one with 29 gpios. This patch
adds the three controller with the gpio driver which is now sitting the
gpio tree.
Cc: devicetree@vger.kernel.org
Acked-by: Alan Tull <atull@altera.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Manual cleanup after the previous Coccinelle script.
Yes, I could write another Coccinelle script to do this but I
don't want labor-replacing robots making an honest programmer's
work obsolete (also, I'm lazy).
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Amir Vadai says:
====================
net/mlx4_core: Deprecate module parameter use_prio
This small patchset deprecates the mlx4_core module paramater 'use_prio', as
suggested by Carol Soto from IBM in [1].
Also, replaced some calls to the prefered pr_warn/info/devel macro's.
Patchset was applied and tested on commit b6052af: "Merge tag
'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge"
[1] - http://marc.info/?l=linux-netdev&m=139871350103432&w=2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As checkpatch suggests. Also changed some printk's into pr_*
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use_prio was added as part of an infrastructure for running FCoE in A0 mode.
FCoE didn't get into Mellanox Upstream driver, and when it will, it won't be
using A0 steering mode.
Therefore we can safely deprecate this module parameter without hurting any
existing user.
CC: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As advanced by the previous patch, the ringbuffers and the engine
command streamers belong in different structs. This is so because,
while they used to be tightly coupled together, the new Logical
Ring Contexts (LRC for short) have a ringbuffer each.
In legacy code, we will use the buffer* pointer inside each ring
to get to the pertaining ringbuffer (the actual switch will be
done in the next patch). In the new Execlists code, this pointer
will be NULL and we will use instead the one inside the context
instead.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
