Bit 7 of UCR3 is described in the i.MX reference manuals (with the exception
of i.MX1) as follows:
ADNIMP: Autobaud Detection Not Improved-. Disables new features of
autobaud detection (See Baud Rate Automatic Detection
Protocol, for more details).
0 Autobaud detection new features selected
1 Keep old autobaud detection mechanism
The "new features" mechanism occasionally cause the receiver to get out of sync
and continuously produce received characters of '\xff'.
In order to reproduce the problem:
$ stty -F /dev/ttymxc0 19200
- Change the terminal baudrate to 19200
- Type in the console and it should look good
- Change the terminal baudrate back to 115200
- Type 'b' in the console, then a stream of garbage characters is seen.
Also rename the bit definition as per the reference manual.
Tested on mx6q, mx6dl, mx6solo and mx53.
Based on a patch from Eric Nelson for U-boot.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This Multi-IO card has one serial 16550-like and one parallel port connector.
Here's the lspci output, after this commit is applied:
03:07.0 Serial controller: Device 4348:5053 (rev 10) (prog-if 02 [16550])
Subsystem: Device 4348:5053
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at cf00 [size=8]
Region 1: I/O ports at ce00 [size=8]
Kernel driver in use: parport_serial
Kernel modules: 8250_pci, parport_serial
This commit adds an entry with the device ID to the blacklist declared in
8250_pci to prevent the driver from taking ownership. Also, and as was done
for the 2S/1P variant, add a quirk to skip autodetection and set the correct
type to 16550A clone.
Proper entries are added to parport_serial, to support the device parallel
and serial ports.
Cc: Gianluca Anzolin <gianluca@sottospazio.it>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing specification of efm32_uart_exit as module_exit.
This fixes the following compilation warning:
drivers/tty/serial/efm32-uart.c:840:123: warning: ‘efm32_uart_exit’ defined but not used [-Wunused-function]
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Jiri Slaby <jslaby@suse.cz>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add format and argument checking and fix misuses in the dbg macro.
Add __printf
Use %pR for resource
Add #include guard to samsung.h
Move static functions from .h to .c
Use vscnprintf instead of length unguarded vsprintf
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't activate the TX Space available IRQ on startup, or a simple
$ cat /dev/ttyHSU0
will cause an endless amount of IRQs, as there is always space in
the TX FIFO available if no data is going to be sent.
Also correct comments for IRQ names (RX and TX swapped).
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On my test platform (B2020/STiH416) the serial port issues bad characters
during the initial message avalanche as the console comes up. The problem
also occurs when dense(ish) I/O is done using the polled I/O interface.
The problem is fixed for me by using the FIFO half-empty bit rather than
FIFO full bit. Note that using the half-empty bit causes the FIFO to be
managed in a similar way to interrupt based I/O (i.e. where the hardware
gets best test coverage).
Running the FIFO half full will have no impact (good or bad) on console
performance. The UART will still remain fully saturated and the busy-wait
until the FIFO is empty in asc_console_write() will complete at the same
time.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xilinx MDM (Microblaze Debug Module) also contains
uart interface via JTAG which is compatible with
uartlite driver. This interface is really slow
that's why timeout is setup to 1s.
Make this time delay not to be cpu speed dependent.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If NO_DMA=y:
drivers/built-in.o: In function `lpuart_dma_rx_free':
fsl_lpuart.c:(.text+0x7da28): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `lpuart_dma_tx_free':
fsl_lpuart.c:(.text+0x7da60): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `lpuart_dma_rx':
fsl_lpuart.c:(.text+0x7dab8): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `lpuart_dma_tx':
fsl_lpuart.c:(.text+0x7db7e): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `lpuart_copy_rx_to_tty':
fsl_lpuart.c:(.text+0x7dcd4): undefined reference to `dma_sync_single_for_cpu'
make[3]: *** [vmlinux] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb78b81142 provide a workaround for
kernel panic, but bring potential deadlock risk. that is in
sirfsoc_rx_tmo_process_tl while enter into sirfsoc_uart_pio_rx_chars
cpu hold uart_port->lock, if uart interrupt comes cpu enter into
sirfsoc_uart_isr and deadlock occurs in getting uart_port->lock.
the patch replace spin_lock version to spin_lock_irq* version to avoid
spinlock dead lock issue. let function tty_flip_buffer_push in tasklet
outof spin_lock_irq* protect area to avoid add the pair of spin_lock and
spin_unlock for tty_flip_buffer_push.
BTW drop self defined unused spinlock protect of tx_lock/rx_lock.
56274.220464] BUG: spinlock lockup suspected on CPU#0, swapper/0/0
[56274.223648] lock: 0xc05d9db0, .magic: dead4ead, .owner: swapper/0/0,
.owner_cpu: 0
[56274.231278] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G
O 3.10.35 #1
[56274.238241] [<c0015530>] (unwind_backtrace+0x0/0xf4) from
[<c00120d8>] (show_stack+0x10/0x14)
[56274.246742] [<c00120d8>] (show_stack+0x10/0x14) from
[<c01b11b0>] (do_raw_spin_lock+0x110/0x184)
[56274.255501] [<c01b11b0>] (do_raw_spin_lock+0x110/0x184) from
[<c02124c8>] (sirfsoc_uart_isr+0x20/0x42c)
[56274.264874] [<c02124c8>] (sirfsoc_uart_isr+0x20/0x42c) from
[<c0075790>] (handle_irq_event_percpu+0x54/0x17c)
[56274.274758] [<c0075790>] (handle_irq_event_percpu+0x54/0x17c)
from [<c00758f4>] (handle_irq_event+0x3c/0x5c)
[56274.284561] [<c00758f4>] (handle_irq_event+0x3c/0x5c) from
[<c0077fa0>] (handle_level_irq+0x98/0xfc)
[56274.293670] [<c0077fa0>] (handle_level_irq+0x98/0xfc) from
[<c0074f44>] (generic_handle_irq+0x2c/0x3c)
[56274.302952] [<c0074f44>] (generic_handle_irq+0x2c/0x3c) from
[<c000ef80>] (handle_IRQ+0x40/0x90)
[56274.311706] [<c000ef80>] (handle_IRQ+0x40/0x90) from
[<c000dc80>] (__irq_svc+0x40/0x70)
[56274.319697] [<c000dc80>] (__irq_svc+0x40/0x70) from
[<c038113c>] (_raw_spin_unlock_irqrestore+0x10/0x48)
[56274.329158] [<c038113c>]
(_raw_spin_unlock_irqrestore+0x10/0x48) from [<c0200034>]
(tty_port_tty_get+0x58/0x90)
[56274.339213] [<c0200034>] (tty_port_tty_get+0x58/0x90) from
[<c0212008>] (sirfsoc_uart_pio_rx_chars+0x1c/0xc8)
[56274.349097] [<c0212008>]
(sirfsoc_uart_pio_rx_chars+0x1c/0xc8) from [<c0212ef8>]
(sirfsoc_rx_tmo_process_tl+0xe4/0x1fc)
[56274.359853] [<c0212ef8>]
(sirfsoc_rx_tmo_process_tl+0xe4/0x1fc) from [<c0027c04>]
(tasklet_action+0x84/0x114)
[56274.369739] [<c0027c04>] (tasklet_action+0x84/0x114) from
[<c0027db4>] (__do_softirq+0x120/0x200)
[56274.378585] [<c0027db4>] (__do_softirq+0x120/0x200) from
[<c0027f44>] (do_softirq+0x54/0x5c)
[56274.386998] [<c0027f44>] (do_softirq+0x54/0x5c) from
[<c00281ec>] (irq_exit+0x9c/0xd0)
[56274.394899] [<c00281ec>] (irq_exit+0x9c/0xd0) from
[<c000ef84>] (handle_IRQ+0x44/0x90)
[56274.402790] [<c000ef84>] (handle_IRQ+0x44/0x90) from
[<c000dc80>] (__irq_svc+0x40/0x70)
[56274.410774] [<c000dc80>] (__irq_svc+0x40/0x70) from
[<c0288af4>] (cpuidle_enter_state+0x50/0xe0)
[56274.419532] [<c0288af4>] (cpuidle_enter_state+0x50/0xe0) from
[<c0288c34>] (cpuidle_idle_call+0xb0/0x148)
[56274.429080] [<c0288c34>] (cpuidle_idle_call+0xb0/0x148) from
[<c000f3ac>] (arch_cpu_idle+0x8/0x38)
[56274.438016] [<c000f3ac>] (arch_cpu_idle+0x8/0x38) from
[<c0059344>] (cpu_startup_entry+0xfc/0x140)
[56274.446956] [<c0059344>] (cpu_startup_entry+0xfc/0x140) from
[<c04a3a54>] (start_kernel+0x2d8/0x2e4)
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All SiRFSoC UART registers are in 32-bits. If we use writeb for
TXFIFO, actually all of 32-bits are still written, for TXTIFO,
only low 8-bits are valid, so in prima2&atlas6, this causes no
problem.
But in the new atlas7, using writeb to write UART registers will
cause an imprecise data abort as HW does check the "wrong" writeb.
So move to writel and this also makes the code consistent with
sirfsoc_uart_pio_tx_chars() in which we use writel.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two new drivers have been added since 3.14, the MEN 16z135 uart, and
the ARM semihosting console. Both are missing an explicit 'select
SERIAL_CORE', which can leads build errors when no other driver
selects the core, as found during ARM randconfig testing.
In case of the ARM semihosting console, we also have to select
SERIAL_CORE_CONSOLE.
This adds the missing 'select' statements.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the warnings:
drivers/tty/serial/sc16is7xx.c: In function 'sc16is7xx_handle_rx':
>> drivers/tty/serial/sc16is7xx.c:548:1: warning: 'sc16is7xx_handle_rx' uses dynamic stack allocation [enabled by default]
drivers/tty/serial/sc16is7xx.c: In function 'sc16is7xx_handle_tx':
>> drivers/tty/serial/sc16is7xx.c:589:1: warning: 'sc16is7xx_handle_tx' uses dynamic stack allocation [enabled by default]
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/tty/serial/sc16is7xx.c:1060:12: warning: 'sc16is7xx_probe' defined but not used [-Wunused-function]
static int sc16is7xx_probe(struct device *dev,
^
drivers/tty/serial/sc16is7xx.c:1176:12: warning: 'sc16is7xx_remove' defined but not used [-Wunused-function]
static int sc16is7xx_remove(struct device *dev)
^
drivers/tty/serial/sc16is7xx.c:1215:29: warning: 'regcfg' defined but not used [-Wunused-variable]
static struct regmap_config regcfg = {
^
Fixed these warnings by removing the `#ifdef CONFIG_REGMAP_I2C' around their
calls as this driver selects REGMAP_I2C in Kconfig. This part of driver just
didn't compile at all when REGMAP_I2C configured as module (CONFIG_REGMAP_I2C
is not defined, just CONFIG_REGMAP_I2C_MODULE).
Signed-off-by: Jan Moskyto Matejka <mq@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Failure to terminate this match table can lead to boot failures
depending on where the compiler places the match table.
Cc: Gabriel FERNANDEZ <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
xdr_reserve_space should now be calculating the length correctly as we
go, so there's no longer any need to fix it up here.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
This is a cosmetic change for now; no change in behavior.
Note we're just depending on xdr_reserve_space to do the bounds checking
for us, we're not really depending on its adjustment of iovec or xdr_buf
lengths yet, as those are fixed up by as necessary after the fact by
read-link operations and by nfs4svc_encode_compoundres. However we do
have to update xdr->iov on read-like operations to prevent
xdr_reserve_space from messing with the already-fixed-up length of the
the head.
When the attribute encoding fails partway through we have to undo the
length adjustments made so far. We do it manually for now, but later
patches will add an xdr_truncate_encode() helper to handle cases like
this.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Konrad writes:
Please git pull the following branch:
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip.git stable/for-jens-3.16
which has a bunch of fixes to the Xen block frontend and backend driver
and a new parameter for Xen backend driver - an override (set by the toolstack)
whether to expose the discard support (if disk of course supports it) or not.
* Move SoC peripherals into an SoC container node
* Move serial enabling into board file (qcom-apq8074-dragonboard.dts)
* Move spi pinctrl into board file
* Cleanup cpu node to match binding spec, enable-method and compatible
should be per cpu, not part of the container
* Drop interrupts property from l2-cache node as its not part of the
binding spec
* Move timer node out of SoC container
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Pull sound fixes from Takashi Iwai:
"Just two small stable fixes: an HD-audio fix for the new Intel
chipsets and a PM handling fix in PCM dmaengine core"
* tag 'sound-3.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix onboard audio on Intel H97/Z97 chipsets
ALSA: pcm_dmaengine: Add check during device suspend
Currently xenwatch blocks in VBD disconnect, waiting for all pending I/O
requests to finish. If the VBD is attached to a hot-swappable disk, then
xenwatch can hang for a long period of time, stalling other watches.
INFO: task xenwatch:39 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
ffff880057f01bd0 0000000000000246 ffff880057f01ac0 ffffffff810b0782
ffff880057f01ad0 00000000000131c0 0000000000000004 ffff880057edb040
ffff8800344c6080 0000000000000000 ffff880058c00ba0 ffff880057edb040
Call Trace:
[<ffffffff810b0782>] ? irq_to_desc+0x12/0x20
[<ffffffff8128f761>] ? list_del+0x11/0x40
[<ffffffff8147a080>] ? wait_for_common+0x60/0x160
[<ffffffff8147bcef>] ? _raw_spin_lock_irqsave+0x2f/0x50
[<ffffffff8147bd49>] ? _raw_spin_unlock_irqrestore+0x19/0x20
[<ffffffff8147a26a>] schedule+0x3a/0x60
[<ffffffffa018fe6a>] xen_blkif_disconnect+0x8a/0x100 [xen_blkback]
[<ffffffff81079f70>] ? wake_up_bit+0x40/0x40
[<ffffffffa018ffce>] xen_blkbk_remove+0xae/0x1e0 [xen_blkback]
[<ffffffff8130b254>] xenbus_dev_remove+0x44/0x90
[<ffffffff81345cb7>] __device_release_driver+0x77/0xd0
[<ffffffff81346488>] device_release_driver+0x28/0x40
[<ffffffff813456e8>] bus_remove_device+0x78/0xe0
[<ffffffff81342c9f>] device_del+0x12f/0x1a0
[<ffffffff81342d2d>] device_unregister+0x1d/0x60
[<ffffffffa0190826>] frontend_changed+0xa6/0x4d0 [xen_blkback]
[<ffffffffa019c252>] ? frontend_changed+0x192/0x650 [xen_netback]
[<ffffffff8130ae50>] ? cmp_dev+0x60/0x60
[<ffffffff81344fe4>] ? bus_for_each_dev+0x94/0xa0
[<ffffffff8130b06e>] xenbus_otherend_changed+0xbe/0x120
[<ffffffff8130b4cb>] frontend_changed+0xb/0x10
[<ffffffff81309c82>] xenwatch_thread+0xf2/0x130
[<ffffffff81079f70>] ? wake_up_bit+0x40/0x40
[<ffffffff81309b90>] ? xenbus_directory+0x80/0x80
[<ffffffff810799d6>] kthread+0x96/0xa0
[<ffffffff81485934>] kernel_thread_helper+0x4/0x10
[<ffffffff814839f3>] ? int_ret_from_sys_call+0x7/0x1b
[<ffffffff8147c17c>] ? retint_restore_args+0x5/0x6
[<ffffffff81485930>] ? gs_change+0x13/0x13
With this patch, when there is still pending I/O, the actual disconnect
is done by the last reference holder (last pending I/O request). In this
case, xenwatch doesn't block indefinitely.
Signed-off-by: Valentin Priescu <priescuv@amazon.com>
Reviewed-by: Steven Kady <stevkady@amazon.com>
Reviewed-by: Steven Noonan <snoonan@amazon.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Newer toolstacks may provide a boolean property "discard-enable" in the
backend node. Its purpose is to disable discard for file backed storage
to avoid fragmentation. Recognize this setting also for physical
storage. If that property exists and is false, do not advertise
"feature-discard" to the frontend.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In its initial implementation a check for "type" was added, but only phy
and file are handled. This breaks advertised discard support for other
type values such as qdisk.
Fix and simplify this function: If the backend advertises discard
support it is supposed to implement it properly, so enable
feature_discard unconditionally. If the backend advertises the need for
a certain granularity and alignment then propagate both properties to
the blocklayer. The discard-secure property is a boolean, update the code
to reflect that.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Pull vfs fix from Al Viro:
"Oh, well... Still nothing useful on that livelock (I had something
that looked kinda-sorta like a non-invasive solution, but it
deadlocks), so it's just Miklos' vmsplice fix for now"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: fix vmplice_to_user()
We already have dummy implementation for most of the regulators APIs for
!CONFIG_REGULATOR case and were missing it for regulator_set_voltage_time().
Found this issue while compiling cpufreq-cpu0 driver without regulators support
in kernel.
drivers/cpufreq/cpufreq-cpu0.c: In function ‘cpu0_cpufreq_probe’:
drivers/cpufreq/cpufreq-cpu0.c:186:3: error: implicit declaration of function ‘regulator_set_voltage_time’ [-Werror=implicit-function-declaration]
Fix this by adding dummy definition for regulator_set_voltage_time().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In a mixed PCI/PCI-X/PCIe topology, bridges can take ownership of
transactions, replacing the original requester ID with their own.
Sometimes we just want to know the resulting device or resulting alias;
other times we want each step in the chain. This iterator allows either
usage. When an endpoint is connected via an unbroken chain of PCIe
switches and root ports, it has no alias and its requester ID is visible to
the root bus. When PCI/X get in the way, we pick up aliases for bridges.
The reason why we potentially care about each step in the path is because
of PCI-X. PCI-X has the concept of a requester ID, but bridges may or may
not take ownership of various types of transactions. We therefore leave it
to the consumer of this function to prune out what they don't care about
rather than attempt to flatten the alias ourselves.
Tested-by: George Spelvin <linux@horizon.com>
Tested-by: Pat Erley <pat-lkml@erley.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We know that "reset_tpt_entry" is false on this side of the if else
statement so there is no need to check again.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 297e0dad72 ("IB/mlx4: Handle Ethernet L2 parameters for IP
based GID addressing") introduced a bug where is_mcast is now no
longer initialized on the non-multicast condition and so it can be
any random value from the stack. This issue was detected by cppcheck:
[drivers/infiniband/hw/mlx4/ah.c:103]: (error) Uninitialized
variable: is_mcast
Simple fix is to initialise is_mcast to zero.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Time comparisons must use time_after / time_before to avoid problems
when jiffies wraps.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Signed-off-by: Roland Dreier <roland@purestorage.com>
As the config option is gone, it's a bit hard to enable it so remove the
reference to it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that CONFIG_USB_DEBUG is gone, remove it from a number of defconfig
files that were enabling it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to e1000, e1000e, ixgbe and i40evf.
Emil provides a fix for ixgbe so that non-fiber devices with MNG FW enabled
are able to link at 100Mbps.
Jacob provides several changes for ixgbe, most of which are PTP related.
Renames ixgbe_ptp_enable() to ixgbe_ptp_feature_enable() to better reflect
the functions purpose. Extracts the hardware setup logic for the PTP
hardware bits from the ixgbe_ptp_set_ts_config() to enable future work for
the ixgbe_ptp_reset(). Maintain the hwstamp configuration through a reset
and extracts the creation of the PTP clock device from ptp_init() in order
to properly handle a suspend/resume cycle and only calls it if we don't
already have a ptp_clock pointer.
David provides a patch to expend the e1000e driver to turn on unicast
PROMISC when there is failure to write to a shared receive address register.
The fix update_phy_task() for 82579 is expanded to include newer PHYs as well
so that the dev_spec->eee_lp_ability has the correct value when going into
SX states.
Todd provides a e1000e fix an errata for 82574/82583 where it is possible
bad bits are read from SYSTIMH/L so check to see that the time is
incrementing at a reasonable rate and is a multiple of the time incremental
value. Removes a redundant igb PHY power down register write.
Andi Kleen out of lines two write functions for e1000e to save 30k text size.
Tobias Klauser converts the e1000 and i40evf drivers to use the
is_broadcast_ether_addr() and is_multicast_ether_addr().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to cast wr_id to unsigned long before casting to a pointer.
This fixes:
drivers/infiniband/hw/mlx5/mr.c: In function 'mlx5_umr_cq_handler':
>> drivers/infiniband/hw/mlx5/mr.c:724:13: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
context = (struct mlx5_ib_umr_context *)wc.wr_id;
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Pull in core changes (again), since we got rid of the alloc/free
hctx mq_ops hooks and mtip32xx then needed updating again.
Signed-off-by: Jens Axboe <axboe@fb.com>
There is no need for drivers to control hardware context allocation
now that we do the context to node mapping in common code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
There's one existing use of 'micrel' in the documentation so use
'micrel' instead of the company's ticker symbol 'mcrl'.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rob Herring <robh@kernel.org>
"7408484 usb: gadget: s3c-hsotg: enable generic phy support" introduces
generic phy support to the dwc2.txt binding and the s3c-hsotg driver
which implements support for the binding. The binding documentation
incorrectly states that the phy-names property will be "device". The
binding example, driver, and one dts user all implement the phy-names
property as requiring "usb2-phy".
Fix the dwc2.txt binding documentation to correctly specify "usb2-phy"
as the appropriate value for phy-names.
Reported-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
None of the blk-mq files have an explanatory comment at the top
for what that particular file does. Add that and add appropriate
copyright notices as well.
Signed-off-by: Jens Axboe <axboe@fb.com>
Hi,
without this patch the istwiRWRequest->MsgContext is always set to zero,
this patch saves the MsgContext in a msgcontext variable and then restores
the value.
Thanks to David Jeffery who found the issue and did the analysis.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Desai, Kashyap <Kashyap.Desai@lsi.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The acornscsi driver was added in v2.1.88. It has always #undef-ed
CONFIG_SCSI_ACORNSCSI_LINK near the top of acornscsi.c. And, just to be
sure, it has also always triggered a preprocessor error if
CONFIG_SCSI_ACORNSCSI_LINK was still defined. But, as far as I can see,
it has never even been possible to set SCSI_ACORNSCSI_LINK through
kconfig, or its predecessors, in the first place.
Let's remove the code involved.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This is the delta between the two submissions:
[PATCH 00/12] scsi/NCR5380: fix debugging macros and #include structure
and
[PATCH v2 00/12] scsi/NCR5380: fix debugging macros and #include structure
The macro definition changes were discussed on the mailing list during
review. The idea is to get the compiler to check the parameters of
disabled printk() calls so that the debugging code doesn't rot again.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
