This field is not used.
Treat PPPIOC*MRU the same way as PPPIOC*FLAGS: "get" requests return 0,
while "set" requests vadidate the user supplied pointer but discard its
value.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ingress, a network device such as a switch assigns to packets
priority based on various criteria. Common options include interpreting
PCP and DSCP fields according to user configuration. When a packet
egresses the switch, a reverse process may rewrite PCP and/or DSCP
values according to packet priority.
The following three functions support a) obtaining a DSCP-to-priority
map or vice versa, and b) finding default-priority entries in APP
database.
The DCB subsystem supports for APP entries a very generous M:N mapping
between priorities and protocol identifiers. Understandably,
several (say) DSCP values can map to the same priority. But this
asymmetry holds the other way around as well--one priority can map to
several DSCP values. For this reason, the following functions operate in
terms of bitmaps, with ones in positions that match some APP entry.
- dcb_ieee_getapp_dscp_prio_mask_map() to compute for a given netdevice
a map of DSCP-to-priority-mask, which gives for each DSCP value a
bitmap of priorities related to that DSCP value by APP, along the
lines of dcb_ieee_getapp_mask().
- dcb_ieee_getapp_prio_dscp_mask_map() similarly to compute for a given
netdevice a map from priorities to a bitmap of DSCPs.
- dcb_ieee_getapp_default_prio_mask() which finds all default-priority
rules for a given port in APP database, and returns a mask of
priorities allowed by these default-priority rules.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case a chain is empty and not explicitly created by a user,
such chain should not exist. The only exception is if there is
an action "goto chain" pointing to it. In that case, don't show the
chain in the dump. Track the chain references held by actions and
use them to find out if a chain should or should not be shown
in chain dump.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2018-07-27
1) Extend the output_mark to also support the input direction
and masking the mark values before applying to the skb.
2) Add a new lookup key for the upcomming xfrm interfaces.
3) Extend the xfrm lookups to match xfrm interface IDs.
4) Add virtual xfrm interfaces. The purpose of these interfaces
is to overcome the design limitations that the existing
VTI devices have.
The main limitations that we see with the current VTI are the
following:
VTI interfaces are L3 tunnels with configurable endpoints.
For xfrm, the tunnel endpoint are already determined by the SA.
So the VTI tunnel endpoints must be either the same as on the
SA or wildcards. In case VTI tunnel endpoints are same as on
the SA, we get a one to one correlation between the SA and
the tunnel. So each SA needs its own tunnel interface.
On the other hand, we can have only one VTI tunnel with
wildcard src/dst tunnel endpoints in the system because the
lookup is based on the tunnel endpoints. The existing tunnel
lookup won't work with multiple tunnels with wildcard
tunnel endpoints. Some usecases require more than on
VTI tunnel of this type, for example if somebody has multiple
namespaces and every namespace requires such a VTI.
VTI needs separate interfaces for IPv4 and IPv6 tunnels.
So when routing to a VTI, we have to know to which address
family this traffic class is going to be encapsulated.
This is a lmitation because it makes routing more complex
and it is not always possible to know what happens behind the
VTI, e.g. when the VTI is move to some namespace.
VTI works just with tunnel mode SAs. We need generic interfaces
that ensures transfomation, regardless of the xfrm mode and
the encapsulated address family.
VTI is configured with a combination GRE keys and xfrm marks.
With this we have to deal with some extra cases in the generic
tunnel lookup because the GRE keys on the VTI are actually
not GRE keys, the GRE keys were just reused for something else.
All extensions to the VTI interfaces would require to add
even more complexity to the generic tunnel lookup.
So to overcome this, we developed xfrm interfaces with the
following design goal:
It should be possible to tunnel IPv4 and IPv6 through the same
interface.
No limitation on xfrm mode (tunnel, transport and beet).
Should be a generic virtual interface that ensures IPsec
transformation, no need to know what happens behind the
interface.
Interfaces should be configured with a new key that must match a
new policy/SA lookup key.
The lookup logic should stay in the xfrm codebase, no need to
change or extend generic routing and tunnel lookups.
Should be possible to use IPsec hardware offloads of the underlying
interface.
5) Remove xfrm pcpu policy cache. This was added after the flowcache
removal, but it turned out to make things even worse.
From Florian Westphal.
6) Allow to update the set mark on SA updates.
From Nathan Harold.
7) Convert some timestamps to time64_t.
From Arnd Bergmann.
8) Don't check the offload_handle in xfrm code,
it is an opaque data cookie for the driver.
From Shannon Nelson.
9) Remove xfrmi interface ID from flowi. After this pach
no generic code is touched anymore to do xfrm interface
lookups. From Benedict Wong.
10) Allow to update the xfrm interface ID on SA updates.
From Nathan Harold.
11) Don't pass zero to ERR_PTR() in xfrm_resolve_and_create_bundle.
From YueHaibing.
12) Return more detailed errors on xfrm interface creation.
From Benedict Wong.
13) Use PTR_ERR_OR_ZERO instead of IS_ERR + PTR_ERR.
From the kbuild test robot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remember the fallback reason code and the peer diagnosis code for
smc sockets, and provide them in smc_diag.c to the netlink interface.
And add more detailed reason codes.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for checking whether polling is used to detect PHY status
changes.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Handle stations tied to AP_VLANs properly during mac80211 hw
reconfig. From Manikanta Pubbisetty.
2) Fix jump stack depth validation in nf_tables, from Taehee Yoo.
3) Fix quota handling in aRFS flow expiration of mlx5 driver, from Eran
Ben Elisha.
4) Exit path handling fix in powerpc64 BPF JIT, from Daniel Borkmann.
5) Use ptr_ring_consume_bh() in page pool code, from Tariq Toukan.
6) Fix cached netdev name leak in nf_tables, from Florian Westphal.
7) Fix memory leaks on chain rename, also from Florian Westphal.
8) Several fixes to DCTCP congestion control ACK handling, from Yuchunk
Cheng.
9) Missing rcu_read_unlock() in CAIF protocol code, from Yue Haibing.
10) Fix link local address handling with VRF, from David Ahern.
11) Don't clobber 'err' on a successful call to __skb_linearize() in
skb_segment(). From Eric Dumazet.
12) Fix vxlan fdb notification races, from Roopa Prabhu.
13) Hash UDP fragments consistently, from Paolo Abeni.
14) If TCP receives lots of out of order tiny packets, we do really
silly stuff. Make the out-of-order queue ending more robust to this
kind of behavior, from Eric Dumazet.
15) Don't leak netlink dump state in nf_tables, from Florian Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
net: axienet: Fix double deregister of mdio
qmi_wwan: fix interface number for DW5821e production firmware
ip: in cmsg IP(V6)_ORIGDSTADDR call pskb_may_pull
bnx2x: Fix invalid memory access in rss hash config path.
net/mlx4_core: Save the qpn from the input modifier in RST2INIT wrapper
r8169: restore previous behavior to accept BIOS WoL settings
cfg80211: never ignore user regulatory hint
sock: fix sg page frag coalescing in sk_alloc_sg
netfilter: nf_tables: move dumper state allocation into ->start
tcp: add tcp_ooo_try_coalesce() helper
tcp: call tcp_drop() from tcp_data_queue_ofo()
tcp: detect malicious patterns in tcp_collapse_ofo_queue()
tcp: avoid collapses in tcp_prune_queue() if possible
tcp: free batches of packets in tcp_prune_ofo_queue()
ip: hash fragments consistently
ipv6: use fib6_info_hold_safe() when necessary
can: xilinx_can: fix power management handling
can: xilinx_can: fix incorrect clear of non-processed interrupts
can: xilinx_can: fix RX overflow interrupt not being enabled
can: xilinx_can: keep only 1-2 frames in TX FIFO to fix TX accounting
...
Skbprio (SKB Priority Queue) is a queueing discipline that prioritizes packets
according to their skb->priority field. Under congestion, already-enqueued lower
priority packets will be dropped to make space available for higher priority
packets. Skbprio was conceived as a solution for denial-of-service defenses that
need to route packets with different priorities as a means to overcome DoS
attacks.
v5
*Do not reference qdisc_dev(sch)->tx_queue_len for setting limit. Instead set
default sch->limit to 64.
v4
*Drop Documentation/networking/sch_skbprio.txt doc file to move it to tc man
page for Skbprio, in iproute2.
v3
*Drop max_limit parameter in struct skbprio_sched_data and instead use
sch->limit.
*Reference qdisc_dev(sch)->tx_queue_len only once, during initialisation for
qdisc (previously being referenced every time qdisc changes).
*Move qdisc's detailed description from in-code to Documentation/networking.
*When qdisc is saturated, enqueue incoming packet first before dequeueing
lowest priority packet in queue - improves usage of call stack registers.
*Introduce and use overlimit stat to keep track of number of dropped packets.
v2
*Use skb->priority field rather than DS field. Rename queueing discipline as
SKB Priority Queue (previously Gatekeeper Priority Queue).
*Queueing discipline is made classful to expose Skbprio's internal priority
queues.
Signed-off-by: Nishanth Devarajan <ndev2021@gmail.com>
Reviewed-by: Sachin Paryani <sachin.paryani@gmail.com>
Reviewed-by: Cody Doucette <doucette@bu.edu>
Reviewed-by: Michel Machado <michel@digirati.com.br>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain PHY's have issues when operating in GBit slave mode and can
be forced to master mode. Examples are RTL8211C, also the Micrel PHY
driver has a DT setting to force master mode.
If two such chips are link partners the autonegotiation will fail.
Standard defines a self-clearing on read, latched-high bit to
indicate this error. Check this bit to inform the user.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
->start() is called once when dump is being initialized, there is no
need to store it in netlink_cb.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Make sure we don't go over the maximum jump stack boundary,
from Taehee Yoo.
2) Missing rcu_barrier() in hash and rbtree sets, also from Taehee.
3) Missing check to nul-node in rbtree timeout routine, from Taehee.
4) Use dev->name from flowtable to fix a memleak, from Florian.
5) Oneliner to free flowtable object on removal, from Florian.
6) Memleak in chain rename transaction, again from Florian.
7) Don't allow two chains to use the same name in the same
transaction, from Florian.
8) handle DCCP SYNC/SYNCACK as invalid, this triggers an
uninitialized timer in conntrack reported by syzbot, from Florian.
9) Fix leak in case netlink_dump_start() fails, from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
Only a few fixes:
* always keep regulatory user hint
* add missing break statement in station flags parsing
* fix non-linear SKBs in port-control-over-nl80211
* reconfigure VLAN stations during HW restart
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers-next patches for 4.19
The first set of patches for 4.19. Only smaller features and bug
fixes, not really anything major. Also included are changes to
include/linux/bitfield.h, we agreed with Johannes that it makes sense
to apply them via wireless-drivers-next.
Major changes:
ath10k
* support channel 173
* fix spectral scan for QCA9984 and QCA9888 chipsets
ath6kl
* add support for Dell Wireless 1537
ti wlcore
* add support for runtime PM
* enable runtime PM autosuspend support
qtnfmac
* support changing MAC address
* enable source MAC address randomization support
libertas
* fix suspend and resume for SDIO cards
mt76
* add software DFS radar pattern detector for mt76x2 based devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many data structures (RDS socket options) used by RDS apps
which use a 32 bit integer to store IP address. To support IPv6,
struct in6_addr needs to be used. To ensure backward compatibility, a
new data structure is introduced for each of those data structures
which use a 32 bit integer to represent an IP address. And new socket
options are introduced to use those new structures. This means that
existing apps should work without a problem with the new RDS module.
For apps which want to use IPv6, those new data structures and socket
options can be used. IPv4 mapped address is used to represent IPv4
address in the new data structures.
v4: Revert changes to SO_RDS_TRANSPORT
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a couple of flower offload commands in order to propagate
template creation/destruction events down to device drivers.
Drivers may use this information to prepare HW in an optimal way
for future filter insertions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow user to set a template for newly created chains. Template lock
down the chain for particular classifier type/options combinations.
The classifier needs to support templates, otherwise kernel would
reply with error.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow user to create, destroy, get and dump chain objects. Do that by
extending rtnl commands by the chain-specific ones. User will now be
able to explicitly create or destroy chains (so far this was done only
automatically according the filter/act needs and refcounting). Also, the
user will receive notification about any chain creation or destuction.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, chain 0 is implicitly created during block creation. However
that does not align with chain object exposure, creation and destruction
api introduced later on. So make the chain 0 behave the same way as any
other chain and only create it when it is needed. Since chain 0 is
somehow special as the qdiscs need to hold pointer to the first chain
tp, this requires to move the chain head change callback infra to the
block structure.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tracer has one event, event 0x26, with two subtypes:
- Subtype 0: Ownership change
- Subtype 1: Traces available
An ownership change occurs in the following cases:
1- Owner releases his ownership, in this case, an event will be
sent to inform others to reattempt acquire ownership.
2- Ownership was taken by a higher priority tool, in this case
the owner should understand that it lost ownership, and go through
tear down flow.
The second subtype indicates that there are traces in the trace buffer,
in this case, the driver polls the tracer buffer for new traces, parse
them and prepares the messages for printing.
The HW starts tracing from the first address in the tracer buffer.
Driver receives an event notifying that new trace block exists.
HW posts a timestamp event at the last 8B of every 256B block.
Comparing the timestamp to the last handled timestamp would indicate
that this is a new trace block. Once the new timestamp is detected,
the entire block is considered valid.
Block validation and parsing, should be done after copying the current
block to a different location, in order to avoid block overwritten
during processing.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Implement FW tracer logic and registers access, initialization and
cleanup flows.
Initializing the tracer will be part of load one flow, as multiple
PFs will try to acquire ownership but only one will succeed and will
be the tracer owner.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5 core infrastructure updates and fixes.
From Eran:
- Add MPEGC (Management PCIe General Configuration) registers and btis
- Fix tristate and description for MLX5 module
rom Feras:
- Add hardware structures for the firmware tracer
From Jainbo:
- Core support for double vlan push/pop steering action
From Max:
- Add XRQ commands definitions
From Noa:
- Add missing SET_DRIVER_VERSION command translation
From Roi:
- Use ERR_CAST() instead of coding it
From Tariq:
- Better return types for CQE API
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Rename field diag_fallback into diag_mode and set the smc mode of a
connection explicitly.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new port attribute - IFLA_BRPORT_BACKUP_PORT, which
allows to set a backup port to be used for known unicast traffic if the
port has gone carrier down. The backup pointer is rcu protected and set
only under RTNL, a counter is maintained so when deleting a port we know
how many other ports reference it as a backup and we remove it from all.
Also the pointer is in the first cache line which is hot at the time of
the check and thus in the common case we only add one more test.
The backup port will be used only for the non-flooding case since
it's a part of the bridge and the flooded packets will be forwarded to it
anyway. To remove the forwarding just send a 0/non-existing backup port.
This is used to avoid numerous scalability problems when using MLAG most
notably if we have thousands of fdbs one would need to change all of them
on port carrier going down which takes too long and causes a storm of fdb
notifications (and again when the port comes back up). In a Multi-chassis
Link Aggregation setup usually hosts are connected to two different
switches which act as a single logical switch. Those switches usually have
a control and backup link between them called peerlink which might be used
for communication in case a host loses connectivity to one of them.
We need a fast way to failover in case a host port goes down and currently
none of the solutions (like bond) cannot fulfill the requirements because
the participating ports are actually the "master" devices and must have the
same peerlink as their backup interface and at the same time all of them
must participate in the bridge device. As Roopa noted it's normal practice
in routing called fast re-route where a precalculated backup path is used
when the main one is down.
Another use case of this is with EVPN, having a single vxlan device which
is backup of every port. Due to the nature of master devices it's not
currently possible to use one device as a backup for many and still have
all of them participate in the bridge (which is master itself).
More detailed information about MLAG is available at the link below.
https://docs.cumulusnetworks.com/display/DOCS/Multi-Chassis+Link+Aggregation+-+MLAG
Further explanation and a diagram by Roopa:
Two switches acting in a MLAG pair are connected by the peerlink
interface which is a bridge port.
the config on one of the switches looks like the below. The other
switch also has a similar config.
eth0 is connected to one port on the server. And the server is
connected to both switches.
br0 -- team0---eth0
|
-- switch-peerlink
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull vfs fixes from Al Viro:
"Fix several places that screw up cleanups after failures halfway
through opening a file (one open-coding filp_clone_open() and getting
it wrong, two misusing alloc_file()). That part is -stable fodder from
the 'work.open' branch.
And Christoph's regression fix for uapi breakage in aio series;
include/uapi/linux/aio_abi.h shouldn't be pulling in the kernel
definition of sigset_t, the reason for doing so in the first place had
been bogus - there's no need to expose struct __aio_sigset in
aio_abi.h at all"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
aio: don't expose __aio_sigset in uapi
ocxlflash_getfile(): fix double-iput() on alloc_file() failures
cxl_getfile(): fix double-iput() on alloc_file() failures
drm_mode_create_lease_ioctl(): fix open-coded filp_clone_open()
kernel_wait4() expects a userland address for status - it's only
rusage that goes as a kernel one (and needs a copyout afterwards)
[ Also, fix the prototype of kernel_wait4() to have that __user
annotation - Linus ]
Fixes: 92ebce5ac5 ("osf_wait4: switch to kernel_wait4()")
Cc: stable@kernel.org # v4.13+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we have offload replay infrastructure added by
commit 326367427c ("net: sched: call reoffload op on block callback reg")
and flows are guaranteed to be removed correctly, we can revert
commit 951a8ee6de ("nfp: reject binding to shared blocks").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Example setup:
host: ip -6 addr add dev eth1 2001:db8:104::4
where eth1 is enslaved to a VRF
switch: ip -6 ro add 2001:db8:104::4/128 dev br1
where br1 only has an LLA
ping6 2001:db8:104::4
ssh 2001:db8:104::4
(NOTE: UDP works fine if the PKTINFO has the address set to the global
address and ifindex is set to the index of eth1 with a destination an
LLA).
For ICMP, icmp6_iif needs to be updated to check if skb->dev is an
L3 master. If it is then return the ifindex from rt6i_idev similar
to what is done for loopback.
For TCP, restore the original tcp_v6_iif definition which is needed in
most places and add a new tcp_v6_iif_l3_slave that considers the
l3_slave variability. This latter check is only needed for socket
lookups.
Fixes: 9ff7438460 ("net: vrf: Handle ipv6 multicast and link-local addresses")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following warning:
net/ipv4/bpfilter/sockopt.c:28:5: error: symbol 'bpfilter_ip_set_sockopt' redeclared with different type
net/ipv4/bpfilter/sockopt.c:34:5: error: symbol 'bpfilter_ip_get_sockopt' redeclared with different type
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like vm_area_dup(), it initializes the anon_vma_chain head, and the
basic mm pointer.
The rest of the fields end up being different for different users,
although the plan is to also initialize the 'vm_ops' field to a dummy
entry.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The vm_area_struct is one of the most fundamental memory management
objects, but the management of it is entirely open-coded evertwhere,
ranging from allocation and freeing (using kmem_cache_[z]alloc and
kmem_cache_free) to initializing all the fields.
We want to unify this in order to end up having some unified
initialization of the vmas, and the first step to this is to at least
have basic allocation functions.
Right now those functions are literally just wrappers around the
kmem_cache_*() calls. This is a purely mechanical conversion:
# new vma:
kmem_cache_zalloc(vm_area_cachep, GFP_KERNEL) -> vm_area_alloc()
# copy old vma
kmem_cache_alloc(vm_area_cachep, GFP_KERNEL) -> vm_area_dup(old)
# free vma
kmem_cache_free(vm_area_cachep, vma) -> vm_area_free(vma)
to the point where the old vma passed in to the vm_area_dup() function
isn't even used yet (because I've left all the old manual initialization
alone).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-07-18
The following series provides fixes to mlx5 core and net device driver.
Please pull and let me know if there's any problem.
For -stable v4.7
net/mlx5e: Don't allow aRFS for encapsulated packets
net/mlx5e: Fix quota counting in aRFS expire flow
For -stable v4.15
net/mlx5e: Only allow offloading decap egress (egdev) flows
net/mlx5e: Refine ets validation function
net/mlx5: Adjust clock overflow work period
For -stable v4.17
net/mlx5: E-Switch, UBSAN fix undefined behavior in mlx5_eswitch_mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-07-20
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add sharing of BPF objects within one ASIC: this allows for reuse of
the same program on multiple ports of a device, and therefore gains
better code store utilization. On top of that, this now also enables
sharing of maps between programs attached to different ports of a
device, from Jakub.
2) Cleanup in libbpf and bpftool's Makefile to reduce unneeded feature
detections and unused variable exports, also from Jakub.
3) First batch of RCU annotation fixes in prog array handling, i.e.
there are several __rcu markers which are not correct as well as
some of the RCU handling, from Roman.
4) Two fixes in BPF sample files related to checking of the prog_cnt
upper limit from sample loader, from Dan.
5) Minor cleanup in sockmap to remove a set but not used variable,
from Colin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-07-20
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix in BPF Makefile to detect llvm-objcopy in a more robust way which is
needed for pahole's BTF converter and minor UAPI tweaks in BTF_INT_BITS()
to shrink the mask before eventual UAPI freeze, from Martin.
2) Fix a segfault in bpftool when prog pin id has no further arguments such
as id value or file specified, from Taeung.
3) Fix powerpc JIT handling of XADD which has jumps to exit path that would
potentially bypass verifier expectations e.g. with subprog calls. Also add
a test case to make sure XADD is not mangling src/dst register, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make net_ns_get_ownership() reusable by networking code outside of core.
This is useful, for example, to allow bridge related sysfs files to be
owned by container root.
Add a function comment since this is a potentially dangerous function to
use given the way that kobject_get_ownership() works by initializing uid
and gid before calling .get_ownership().
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Plumb in get_ownership() callback for devices belonging to a class so that
they can be created with uid/gid different from global root. This will
allow network devices in a container to belong to container's root and not
global root.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normally kobjects and their sysfs representation belong to global root,
however it is not necessarily the case for objects in separate namespaces.
For example, objects in separate network namespace logically belong to the
container's root and not global root.
This change lays groundwork for allowing network namespace objects
ownership to be transferred to container's root user by defining
get_ownership() callback in ktype structure and using it in sysfs code to
retrieve desired uid/gid when creating sysfs objects for given kobject.
Co-Developed-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows creating kernfs files and directories with arbitrary
uid/gid instead of always using GLOBAL_ROOT_UID/GID by extending
kernfs_create_dir_ns() and kernfs_create_file_ns() with uid/gid arguments.
The "simple" kernfs_create_file() and kernfs_create_dir() are left alone
and always create objects belonging to the global root.
When creating symlinks ownership (uid/gid) is taken from the target kernfs
object.
Co-Developed-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree:
1) No need to set ttl from reject action for the bridge family, from
Taehee Yoo.
2) Use a fixed timeout for flow that are passed up from the flowtable
to conntrack, from Florian Westphal.
3) More preparation patches for tproxy support for nf_tables, from Mate
Eckl.
4) Remove unnecessary indirection in core IPv6 checksum function, from
Florian Westphal.
5) Use nf_ct_get_tuplepr() from openvswitch, instead of opencoding it.
From Florian Westphal.
6) socket match now selects socket infrastructure, instead of depending
on it. From Mate Eckl.
7) Patch series to simplify conntrack tuple building/parsing from packet
path and ctnetlink, from Florian Westphal.
8) Fetch timeout policy from protocol helpers, instead of doing it from
core, from Florian Westphal.
9) Merge IPv4 and IPv6 protocol trackers into conntrack core, from
Florian Westphal.
10) Depend on CONFIG_NF_TABLES_IPV6 and CONFIG_IP6_NF_IPTABLES
respectively, instead of IPV6. Patch from Mate Eckl.
11) Add specific function for garbage collection in conncount,
from Yi-Hung Wei.
12) Catch number of elements in the connlimit list, from Yi-Hung Wei.
13) Move locking to nf_conncount, from Yi-Hung Wei.
14) Series of patches to add lockless tree traversal in nf_conncount,
from Yi-Hung Wei.
15) Resolve clash in matching conntracks when race happens, from
Martynas Pumputis.
16) If connection entry times out, remove template entry from the
ip_vs_conn_tab table to improve behaviour under flood, from
Julian Anastasov.
17) Remove useless parameter from nf_ct_helper_ext_add(), from Gao feng.
18) Call abort from 2-phase commit protocol before requesting modules,
make sure this is done under the mutex, from Florian Westphal.
19) Grab module reference when starting transaction, also from Florian.
20) Dynamically allocate expression info array for pre-parsing, from
Florian.
21) Add per netns mutex for nf_tables, from Florian Westphal.
22) A couple of patches to simplify and refactor nf_osf code to prepare
for nft_osf support.
23) Break evaluation on missing socket, from Mate Eckl.
24) Allow to match socket mark from nft_socket, from Mate Eckl.
25) Remove dependency on nf_defrag_ipv6, now that IPv6 tracker is
built-in into nf_conntrack. From Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Per DCTCP RFC8257 (Section 3.2) the ACK reflecting the CE status change
has to be sent immediately so the sender can respond quickly:
""" When receiving packets, the CE codepoint MUST be processed as follows:
1. If the CE codepoint is set and DCTCP.CE is false, set DCTCP.CE to
true and send an immediate ACK.
2. If the CE codepoint is not set and DCTCP.CE is true, set DCTCP.CE
to false and send an immediate ACK.
"""
Previously DCTCP implementation may continue to delay the ACK. This
patch fixes that to implement the RFC by forcing an immediate ACK.
Tested with this packetdrill script provided by Larry Brakmo
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
0.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
0.000 setsockopt(3, SOL_TCP, TCP_CONGESTION, "dctcp", 5) = 0
0.000 bind(3, ..., ...) = 0
0.000 listen(3, 1) = 0
0.100 < [ect0] SEW 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
0.100 > SE. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 8>
0.110 < [ect0] . 1:1(0) ack 1 win 257
0.200 accept(3, ..., ...) = 4
+0 setsockopt(4, SOL_SOCKET, SO_DEBUG, [1], 4) = 0
0.200 < [ect0] . 1:1001(1000) ack 1 win 257
0.200 > [ect01] . 1:1(0) ack 1001
0.200 write(4, ..., 1) = 1
0.200 > [ect01] P. 1:2(1) ack 1001
0.200 < [ect0] . 1001:2001(1000) ack 2 win 257
+0.005 < [ce] . 2001:3001(1000) ack 2 win 257
+0.000 > [ect01] . 2:2(0) ack 2001
// Previously the ACK below would be delayed by 40ms
+0.000 > [ect01] E. 2:2(0) ack 3001
+0.500 < F. 9501:9501(0) ack 4 win 257
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when a DCTCP receiver delays an ACK and receive a
data packet with a different CE mark from the previous one's, it
sends two immediate ACKs acking previous and latest sequences
respectly (for ECN accounting).
Previously sending the first ACK may mark off the delayed ACK timer
(tcp_event_ack_sent). This may subsequently prevent sending the
second ACK to acknowledge the latest sequence (tcp_ack_snd_check).
The culprit is that tcp_send_ack() assumes it always acknowleges
the latest sequence, which is not true for the first special ACK.
The fix is to not make the assumption in tcp_send_ack and check the
actual ack sequence before cancelling the delayed ACK. Further it's
safer to pass the ack sequence number as a local variable into
tcp_send_ack routine, instead of intercepting tp->rcv_nxt to avoid
future bugs like this.
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull IOMMU fix from Joerg Roedel:
"Only one revert, for an an Intel VT-d patch that caused issues with
the i915 GPU driver"
* tag 'iommu-fixes-v4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
Revert "iommu/vt-d: Clean up pasid quirk for pre-production devices"
no need to store the name in separate area.
Furthermore, it uses kmalloc but not kfree and most accesses seem to treat
it as char[IFNAMSIZ] not char *.
Remove this and use dev->name instead.
In case event zeroed dev, just omit the name in the dump.
Fixes: d92191aa84 ("netfilter: nf_tables: cache device name in flowtable object")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch shrinks the BTF_INT_BITS() mask. The current
btf_int_check_meta() ensures the nr_bits of an integer
cannot exceed 64. Hence, it is mostly an uapi cleanup.
The actual btf usage (i.e. seq_show()) is also modified
to use u8 instead of u16. The verification (e.g. btf_int_check_meta())
path stays as is to deal with invalid BTF situation.
Fixes: 69b693f0ae ("bpf: btf: Introduce BPF Type Format (BTF)")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In order to remove performance impact of having the extra u32 in every
single flowi, this change removes the flowi_xfrm struct, prefering to
take the if_id as a method parameter where needed.
In the inbound direction, if_id is only needed during the
__xfrm_check_policy() function, and the if_id can be determined at that
point based on the skb. As such, xfrmi_decode_session() is only called
with the skb in __xfrm_check_policy().
In the outbound direction, the only place where if_id is needed is the
xfrm_lookup() call in xfrmi_xmit2(). With this change, the if_id is
directly passed into the xfrm_lookup_with_ifid() call. All existing
callers can still call xfrm_lookup(), which uses a default if_id of 0.
This change does not change any behavior of XFRMIs except for improving
overall system performance via flowi size reduction.
This change has been tested against the Android Kernel Networking Tests:
https://android.googlesource.com/kernel/tests/+/master/net/test
Signed-off-by: Benedict Wong <benedictwong@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
