commit 8b438686a0 upstream.
Commit 7383d44b added a pointer pdata which get set to the default
platform_data when non was defined in the device. But it did not
pass this pointer to the st_sensors_init_sensor call but still
used the maybe uninitialized platform_data from dev.
This breaks initialization when no platform_data is given and
the optional st,drdy-int-pin devicetree option is not set.
This commit fixes this.
Cc: stable@vger.kernel.org
Fixes: 7383d44b ("iio: st_pressure: st_accel: Initialise sensor platform data properly")
Signed-off-by: Michael Nosthoff <committed@heine.so>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b91e146c38 upstream.
CCS811 has different I2C register maps in boot and application mode. When
CCS811 is in boot mode, register APP_START (0xF4) is used to transit the
firmware state from boot to application mode. However, APP_START is not a
valid register location when CCS811 is in application mode (refer to
"CCS811 Bootloader Register Map" and "CCS811 Application Register Map" in
CCS811 datasheet). The driver should not attempt to perform a write to
APP_START while CCS811 is in application mode, as this is not a valid or
documented register location.
When prob function is being called, the driver assumes the CCS811 sensor
is in boot mode, and attempts to perform a write to APP_START. Although
CCS811 powers-up in boot mode, it may have already been transited to
application mode by previous instances, e.g. unload and reload device
driver by the system, or explicitly by user. Depending on the system
design, CCS811 sensor may be permanently connected to system power source
rather than power controlled by GPIO, hence it is possible that the sensor
is never power reset, thus the firmware could be in either boot or
application mode at any given time when driver prob function is being
called.
This patch checks the STATUS register before attempting to send a write to
APP_START. Only if the firmware is not in application mode and has valid
firmware application loaded, then it will continue to start transiting the
firmware boot to application mode.
Signed-off-by: Richard Lai <richard@richardman.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2e64438487 ]
Lower bits of the INA219/220 bus voltage register are conversion
status flags, properly shift the value.
When reading via IIO buffer, the value is passed on unaltered,
shifting is the responsibility of the user.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f027e0b3a7 upstream.
The adis_probe_trigger() creates a new IIO trigger and requests an
interrupt associated with the trigger. The interrupt uses the generic
iio_trigger_generic_data_rdy_poll() function as its interrupt handler.
Currently the driver initializes some fields of the trigger structure after
the interrupt has been requested. But an interrupt can fire as soon as it
has been requested. This opens up a race condition.
iio_trigger_generic_data_rdy_poll() will access the trigger data structure
and dereference the ops field. If the ops field is not yet initialized this
will result in a NULL pointer deref.
It is not expected that the device generates an interrupt at this point, so
typically this issue did not surface unless e.g. due to a hardware
misconfiguration (wrong interrupt number, wrong polarity, etc.).
But some newer devices from the ADIS family start to generate periodic
interrupts in their power-on reset configuration and unfortunately the
interrupt can not be masked in the device. This makes the race condition
much more visible and the following crash has been observed occasionally
when booting a system using the ADIS16460.
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = c0004000
[00000008] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.9.0-04126-gf9739f0-dirty #257
Hardware name: Xilinx Zynq Platform
task: ef04f640 task.stack: ef050000
PC is at iio_trigger_notify_done+0x30/0x68
LR is at iio_trigger_generic_data_rdy_poll+0x18/0x20
pc : [<c042d868>] lr : [<c042d924>] psr: 60000193
sp : ef051bb8 ip : 00000000 fp : ef106400
r10: c081d80a r9 : ef3bfa00 r8 : 00000087
r7 : ef051bec r6 : 00000000 r5 : ef3bfa00 r4 : ee92ab00
r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : ee97e400
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment none
Control: 18c5387d Table: 0000404a DAC: 00000051
Process swapper/0 (pid: 1, stack limit = 0xef050210)
[<c042d868>] (iio_trigger_notify_done) from [<c0065b10>] (__handle_irq_event_percpu+0x88/0x118)
[<c0065b10>] (__handle_irq_event_percpu) from [<c0065bbc>] (handle_irq_event_percpu+0x1c/0x58)
[<c0065bbc>] (handle_irq_event_percpu) from [<c0065c30>] (handle_irq_event+0x38/0x5c)
[<c0065c30>] (handle_irq_event) from [<c0068e28>] (handle_level_irq+0xa4/0x130)
[<c0068e28>] (handle_level_irq) from [<c0064e74>] (generic_handle_irq+0x24/0x34)
[<c0064e74>] (generic_handle_irq) from [<c021ab7c>] (zynq_gpio_irqhandler+0xb8/0x13c)
[<c021ab7c>] (zynq_gpio_irqhandler) from [<c0064e74>] (generic_handle_irq+0x24/0x34)
[<c0064e74>] (generic_handle_irq) from [<c0065370>] (__handle_domain_irq+0x5c/0xb4)
[<c0065370>] (__handle_domain_irq) from [<c000940c>] (gic_handle_irq+0x48/0x8c)
[<c000940c>] (gic_handle_irq) from [<c0013e8c>] (__irq_svc+0x6c/0xa8)
To fix this make sure that the trigger is fully initialized before
requesting the interrupt.
Fixes: ccd2b52f4a ("staging:iio: Add common ADIS library")
Reported-by: Robin Getz <Robin.Getz@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 511051d509 upstream.
Functions for triggered buffer support are needed by this module.
If they are not defined accidentally by another driver, there's an error
thrown out while linking.
Add a select of IIO_BUFFER and IIO_TRIGGERED_BUFFER in the Kconfig file.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Fixes: a831959371 ("iio: srf08: add triggered buffer support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3b5655ebd upstream.
Error handling in stm32h7_adc_enable routine doesn't unwind enable
sequence correctly. ADEN can only be cleared by hardware (e.g. by
writing one to ADDIS).
It's also better to clear ADRDY just after it's been set by hardware.
Fixes: 95e339b6e8 ("iio: adc: stm32: add support for STM32H7")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c175cb7cd9 ]
Fix build errors in kernel-doc notation. Symbols that end in '_'
have a special meaning, but adding a '*' makes them OK.
../drivers/iio/industrialio-core.c:635: ERROR: Unknown target name: "iio_val".
../drivers/iio/industrialio-core.c:642: ERROR: Unknown target name: "iio_val".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e53111ad5d ]
The commit 0f0796509c
("iio: remove gpio interrupt probing from drivers that use a single interrupt")
removed custom IRQ assignment for the drivers which are enumerated via
ACPI or OF. Unfortunately, some ACPI tables have IRQ line defined as
GpioIo() resource and thus automatic IRQ allocation will fail.
Partially revert the commit 0f0796509c to restore original behaviour.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f114acd4e upstream.
in_concentration_raw should report, according to sysfs-bus-iio documentation,
a "Raw (unscaled no offset etc.) percentage reading of a substance."
Modify scale to convert from ppm/ppb to percentage:
1 ppm = 0.0001%
1 ppb = 0.0000001%
There is no offset needed to convert the ppm/ppb to percentage,
so remove offset from IIO_CONCENTRATION (IIO_MOD_CO2) channel.
Cc'd stable to reduce chance of userspace breakage in the long
run as we fix this wrong bit of ABI usage.
Signed-off-by: Narcisa Ana Maria Vasile <narcisaanamaria12@gmail.com>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04e491ca9d upstream.
By default, watermark is set to '1'. Watermark is used to fine tune
cyclic dma buffer period. In case watermark is left untouched (e.g. 1)
and several channels are being scanned, buffer period is wrongly set
(e.g. to 1 sample). As a consequence, data is never pushed to upper layer.
Fix buffer period size, by taking scan channels number into account.
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e72a060151 ]
Introduce register mask for data-ready status register since
pressure sensors (e.g. LPS22HB) export just two channels
(BIT(0) and BIT(1)) and BIT(2) is marked reserved while in
st_sensors_new_samples_available() value read from status register
is masked using 0x7.
Moreover do not mask status register using active_scan_mask since
now status value is properly masked and if the result is not zero the
interrupt has to be consumed by the driver. This fix an issue on LPS25H
and LPS331AP where channel definition is swapped respect to status
register.
Furthermore that change allows to properly support new devices
(e.g LIS2DW12) that report just ZYXDA (data-ready) field in status register
to figure out if the interrupt has been generated by the device.
Fixes: 97865fe413 (iio: st_sensors: verify interrupt event to status)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96748823c4 upstream.
The Meson GXBB and newer SoCs have a few more registers than the older
Meson8 and Meson8b SoCs.
Use a separate regmap config to limit the older SoCs to the DELTA_10
register.
Fixes: 6c76ed31cd ("iio: adc: meson-saradc: add Meson8b SoC compatibility")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d85eed9f57 upstream.
Meson8 and Meson8b do not have the MESON_SAR_ADC_REG11 register. The
bandgap setting for these SoCs is configured in the
MESON_SAR_ADC_DELTA_10 register instead.
Make the driver aware of this difference and use the correct bandgap
register depending on the SoC.
This has worked fine on Meson8 and Meson8b because the bootloader is
already initializing the bandgap setting.
Fixes: 6c76ed31cd ("iio: adc: meson-saradc: add Meson8b SoC compatibility")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a6b0420d2 upstream.
Meson8 and Meson8b SoCs use the the SAR ADC gate clock provided by the
MESON_SAR_ADC_REG3 register within the SAR ADC register area.
According to the datasheet (and the existing MESON_SAR_ADC_REG3_CLK_EN
definition) the gate is on bit 30.
The fls() function returns the last set bit, which is "bit index + 1"
(fls(MESON_SAR_ADC_REG3_CLK_EN) returns 31). Fix this by switching to
__ffs() which returns the first set bit, which is bit 30 in our case.
This off by one error results in the ADC not being usable on devices
where the bootloader did not enable the clock.
Fixes: 3adbf34273 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81b039ec36 upstream.
Function platform_get_irq_byname() returns a negative error code on
failure, and a zero or positive number on success. However, in function
cpcap_adc_probe(), positive IRQ numbers are also taken as error cases.
Use "if (ddata->irq < 0)" instead of "if (!ddata->irq)" to validate the
return value of platform_get_irq_byname().
Signed-off-by: Pan Bian <bianpan2016@163.com>
Fixes: 25ec249632 ("iio: adc: cpcap: Add minimal support for CPCAP PMIC ADC")
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dd92d5ea20 ]
Check return values from call to devm_kzalloc() and devm_kmemup()
in order to prevent a NULL pointer dereference.
This issue was detected using Coccinelle and the following semantic patch:
@@
expression x;
identifier fld;
@@
* x = devm_kzalloc(...);
... when != x == NULL
x->fld
Fixes: 7ba9df54b0 ("iio: multiplexer: new iio category and iio-mux driver")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dln2-adc driver uses interface(s) that are controlled by the
IIO_TRIGGERED_BUFFER Kconfig symbol, so the driver needs to select
that symbol to prevent the build error.
drivers/iio/adc/dln2-adc.o: In function `dln2_adc_probe':
dln2-adc.c:(.text+0x528): undefined reference to `devm_iio_triggered_buffer_setup'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Cc: Jack Andersen <jackoalan@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add missing break in iio_simple_dummy_write_event_config() for the voltage
threshold event enable attribute. Without this writing to the
in_voltage0_thresh_rising_en always returns -EINVAL even though the change
was correctly applied.
Fixes: 3e34e650db ("iio: dummy: Demonstrate the usage of new channel types")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With gcc 4.1.2:
drivers/iio/pressure/zpa2326.c: In function ‘zpa2326_wait_oneshot_completion’:
drivers/iio/pressure/zpa2326.c:868: warning: ‘ret’ may be used uninitialized in this function
When testing for "timeout < 0", timeout is already guaranteed to be
strict negative, so the branch is always taken, and ret is thus always
initialized. But (some version of) gcc is not smart enough to notice.
Remove the check to fix this.
As there is no other code in between assigning the error codes and
returning them, the error codes can be returned immediately, and the
intermediate variable can be dropped.
Drop the "else" to please checkpatch.
Fixes: e7215fe4d5 ("iio: pressure: zpa2326: report interrupted case as failure")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Most applications are too noisy to allow the default noise and
watchdog settings, and thus need to be configurable via DT
properties.
Also default settings to POR defaults on a reset, and register
distuber interrupts as noise since it prevents proper usage.
Cc: devicetree@vger.kernel.org
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jonathan writes:
First round of IIO fixes for the 4.14 cycle
Note this includes fixes from recent merge window. As such the tree
is based on top of a prior staging/staging-next tree.
* iio core
- return and error for a failed read_reg debugfs call rather than
eating the error.
* ad7192
- Use the dedicated reset function in the ad_sigma_delta library
instead of an spi transfer with the data on the stack which
could cause problems with DMA.
* ad7793
- Implement a dedicate reset function in the ad_sigma_delta library
and use it to correctly reset this part.
* bme280
- ctrl_reg write must occur after any register writes
for updates to take effect.
* mcp320x
- negative voltage readout was broken.
- Fix an oops on module unload due to spi_set_drvdata not being called
in probe.
* st_magn
- Fix the data ready line configuration for the lis3mdl. It is not
configurable so the st_magn core was assuming it didn't exist
and so wasn't consuming interrupts resulting in an unhandled
interrupt.
* stm32-adc
- off by one error on max channels checking.
* stm32-timer
- preset should not be buffered - reorganising register writes avoids
this.
- fix a corner case in which write preset goes wrong when a timer is
used first as a trigger then as a counter with preset. Odd case but
you never know.
* ti-ads1015
- Fix setting of comparator polarity by fixing bitfield definition.
* twl4030
- Error path handling fix to cleanup in event of regulator
registration failure.
- Disable the vusb3v1 regulator correctly in error handling
- Don't paper over a regulator enable failure.
If an IIO device returns an error code for a read access via debugfs, it
is currently ignored by the IIO core (other than emitting an error
message). Instead, return this error code to user space, so upper layers
can detect it correctly.
Signed-off-by: Matt Fornero <matt.fornero@mathworks.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The serial interface can be reset by writing 32 consecutive 1s to the device.
'ret' was initialized correctly but its value was overwritten when
ad7793_check_platform_data() was called. Since a dedicated reset function
is present now, it should be used instead.
Fixes: 2edb769d24 ("iio:ad7793: Add support for the ad7798 and ad7799")
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since most of the SD ADCs have the option of reseting the serial
interface by sending a number of SCLKs with CS = 0 and DIN = 1,
a dedicated function that can do this is usefull.
Needed for the patch: iio: ad7793: Fix the serial interface reset
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ctrl_reg register needs to be written after any write to
the humidity registers. The value written to the ctrl_reg register
does not necessarily need to change, but a write operation must
occur.
The regmap_update_bits functions will not write to a register
if the register value matches the value to be written. This saves
unnecessary bus operations. The change in this patch forces a bus
write during the chip_config operation by switching to
regmap_write_bits.
This will fix issues where the Humidity Sensor Oversampling bits
are not updated after initialization.
Signed-off-by: Colin Parker <colin.parker@aclima.io>
Acked-by: Andreas Klinger <ak@it-klinger.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit f686a36b4b ("iio: adc: mcp320x: Add support for mcp3301")
returns a signed voltage from mcp320x_adc_conversion() but neglects that
the caller interprets a negative return value as failure. Only mcp3301
(and the upcoming mcp3550/1/3) is affected as the other chips are
incapable of measuring negative voltages.
Fix and while at it, add mcp3301 to the list of supported chips at the
top of the file.
Fixes: f686a36b4b ("iio: adc: mcp320x: Add support for mcp3301")
Cc: Andrea Galbusera <gizero@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver calls spi_get_drvdata() in its ->remove hook even though it
has never called spi_set_drvdata(). Stack trace for posterity:
Unable to handle kernel NULL pointer dereference at virtual address 00000220
Internal error: Oops: 5 [#1] SMP ARM
[<8072f564>] (mutex_lock) from [<7f1400d0>] (iio_device_unregister+0x24/0x7c [industrialio])
[<7f1400d0>] (iio_device_unregister [industrialio]) from [<7f15e020>] (mcp320x_remove+0x20/0x30 [mcp320x])
[<7f15e020>] (mcp320x_remove [mcp320x]) from [<8055a8cc>] (spi_drv_remove+0x2c/0x44)
[<8055a8cc>] (spi_drv_remove) from [<805087bc>] (__device_release_driver+0x98/0x134)
[<805087bc>] (__device_release_driver) from [<80509180>] (driver_detach+0xdc/0xe0)
[<80509180>] (driver_detach) from [<8050823c>] (bus_remove_driver+0x5c/0xb0)
[<8050823c>] (bus_remove_driver) from [<80509ab0>] (driver_unregister+0x38/0x58)
[<80509ab0>] (driver_unregister) from [<7f15e69c>] (mcp320x_driver_exit+0x14/0x1c [mcp320x])
[<7f15e69c>] (mcp320x_driver_exit [mcp320x]) from [<801a78d0>] (SyS_delete_module+0x184/0x1d0)
[<801a78d0>] (SyS_delete_module) from [<80108100>] (ret_fast_syscall+0x0/0x1c)
Fixes: f5ce4a7a92 ("iio: adc: add driver for MCP3204/08 12-bit ADC")
Cc: Oskar Andero <oskar.andero@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix a bad error check when counting 'st,adc-channels' array elements.
This is seen when all channels are in use simultaneously.
Fixes: 64ad7f643 ("iio: adc: stm32: introduce compatible data cfg")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Balance timer start routine that sets ARPE: clear it in stop routine.
This fixes a corner case, when timer is used successively as trigger
(with sampling_frequency start/stop routines), then as a counter
(with preset).
Fixes: 93fbe91b55 ("iio: Add STM32 timer trigger driver")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, setting preset value (ARR) will update directly 'Auto reload
value' only on 1st write access. But then, ARPE is set. This makes
ARR a shadow register. Preset value should be updated upon each
write request: ensure ARPE is 0. This fixes successive writes to
preset attribute.
Fixes: 4adec7da05 ("iio: stm32 trigger: Add quadrature encoder device")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If we can not enable the regulator, go through the error handling path
instead of silently continuing.
Fixes: 7cc97d77ee ("iio: adc: twl4030: Fix ADC[3:6] readings")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 7cc97d77ee has introduced a call to 'regulator_disable()' in the
.remove function.
So we should also have such a call in the .probe function in case of
error after a successful 'regulator_enable()' call.
Add a new label for that and use it.
Fixes: 7cc97d77ee ("iio: adc: twl4030: Fix ADC[3:6] readings")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If 'devm_regulator_get()' fails, we should go through the existing error
handling path instead of returning directly, as done is all the other
error handling paths in this function.
Fixes: 7cc97d77ee ("iio: adc: twl4030: Fix ADC[3:6] readings")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
Pull HID update from Jiri Kosina:
- Wacom driver fixes/updates (device name generation improvements,
touch ring status support) from Jason Gerecke
- T100 touchpad support from Hans de Goede
- support for batteries driven by HID input reports, from Dmitry
Torokhov
- Arnd pointed out that driver_lock semaphore is superfluous, as driver
core already provides all the necessary concurency protection.
Removal patch from Binoy Jayan
- logical minimum numbering improvements in sensor-hub driver, from
Srinivas Pandruvada
- support for Microsoft Win8 Wireless Radio Controls extensions from
João Paulo Rechi Vita
- assorted small fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (28 commits)
HID: prodikeys: constify snd_rawmidi_ops structures
HID: sensor: constify platform_device_id
HID: input: throttle battery uevents
HID: usbmouse: constify usb_device_id and fix space before '[' error
HID: usbkbd: constify usb_device_id and fix space before '[' error.
HID: hid-sensor-hub: Force logical minimum to 1 for power and report state
HID: wacom: Do not completely map WACOM_HID_WD_TOUCHRINGSTATUS usage
HID: asus: Add T100CHI bluetooth keyboard dock touchpad support
HID: ntrig: constify attribute_group structures.
HID: logitech-hidpp: constify attribute_group structures.
HID: sensor: constify attribute_group structures.
HID: multitouch: constify attribute_group structures.
HID: multitouch: use proper symbolic constant for 0xff310076 application
HID: multitouch: Support Asus T304UA media keys
HID: multitouch: Support HID_GD_WIRELESS_RADIO_CTLS
HID: input: optionally use device id in battery name
HID: input: map digitizer battery usage
HID: Remove the semaphore driver_lock
HID: wacom: add USB_HID dependency
HID: add ALWAYS_POLL quirk for Logitech 0xc077
...
STM32 ADC supports hardware triggers like STM32 Low-Power Timer.
For instance, STM32H7 ADC may be triggered by instances 1, 2 or 3.
Add hardware triggered mode so Low-Power Timer Trigger driver can
validate device.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for LPTIMx_OUT triggers that can be found on some STM32
devices. These triggers can be used then by ADC or DAC.
Typical usage is to configure LPTimer as PWM output (via pwm-stm32-lp)
and have synchronised analog conversions with these triggers.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Data-ready line in LIS3MDL is routed to drdy pin and it is not possible
to select a different INT pin. st_sensors_set_dataready_irq() assumes
that if drdy int address is not exported in register map, irq trigger
is not supported by the sensor and hw_irq_trigger is always false.
Based on this configuration st_sensors_irq_thread does not consume
generated interrupt causing an unhandled irq.
Fix this taking into account status register address in
st_sensors_set_dataready_irq()
Fixes: 90efe05562 (iio: st_sensors: harden interrupt handling)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
