commit 639fa43d59 upstream.
When a BRx is provided by a pipeline, the WPF must determine the master
layer. Currently the condition to check this identifies pipe->bru ||
pipe->num_inputs > 1.
The code then moves on to dereference pipe->bru, thus the check fails
static analysers on the possibility that pipe->num_inputs could be
greater than 1 without pipe->bru being set.
The reality is that the pipeline must have a BRx to support more than
one input, thus this could never cause a fault - however it also
identifies that the num_inputs > 1 check is redundant.
Remove the redundant check - and always configure the master layer
appropriately when we have a BRx configured in our pipeline.
Fixes: 6134148f60 ("v4l: vsp1: Add support for the BRS entity")
Cc: stable@vger.kernel.org
Suggested-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 613928e853 upstream.
To allow dual pipelines utilising two WPF entities when available, the
VSP was updated to support header-mode display list in continuous
pipelines.
A small bug in the status check of the command register causes the
second pipeline to be directly afflicted by the running of the first;
appearing as a perceived performance issue with stuttering display.
Fix the vsp1_dl_list_hw_update_pending() call to ensure that the read
comparison corresponds to the correct pipeline.
Fixes: eaf4bfad6a ("v4l: vsp1: Add support for header display lists in continuous mode")
Cc: "Stable v4.14+" <stable@vger.kernel.org>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f6c11044f ]
Two orthogonal changesets caused a breakage at a printk
inside davinci. Commit a2d17962c9
("[media] davinci: Switch from V4L2 OF to V4L2 fwnode")
made davinci to use struct fwnode_handle instead of
struct device_node. Commit 68d9c47b16
("media: Convert to using %pOF instead of full_name")
changed the printk to not use ->full_name, but, instead,
to rely on %pOF.
With both patches applied, the Kernel will do the wrong
thing, as warned by smatch:
drivers/media/platform/davinci/vpif_capture.c:1399 vpif_async_bound() error: '%pOF' expects argument of type 'struct device_node*', argument 5 has type 'void*'
So, change the logic to actually print the device name
that was obtained before the print logic.
Fixes: 68d9c47b16 ("media: Convert to using %pOF instead of full_name")
Fixes: a2d17962c9 ("[media] davinci: Switch from V4L2 OF to V4L2 fwnode")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f45ce98775 ]
Driver calls request_firmware() whenever the device is opened for the
first time. As the device gets opened and closed, dev->num_inst == 1
is true several times. This is not necessary since the firmware is saved
in the fw_buf. s5p_mfc_load_firmware() copies the buffer returned by
the request_firmware() to dev->fw_buf.
fw_buf sticks around until it gets released from s5p_mfc_remove(), hence
there is no need to keep requesting firmware and copying it to fw_buf.
This might have been overlooked when changes are made to free fw_buf from
the device release interface s5p_mfc_release().
Fix s5p_mfc_load_firmware() to call request_firmware() once and keep state.
Change _probe() to load firmware once fw_buf has been allocated.
s5p_mfc_open() and it continues to call s5p_mfc_load_firmware() and init
hardware which is the step where firmware is written to the device.
This addresses the mfc_mutex contention due to repeated request_firmware()
calls from open() in the following circular locking warning:
[ 552.194115] qtdemux0:sink/2710 is trying to acquire lock:
[ 552.199488] (&dev->mfc_mutex){+.+.}, at: [<bf145544>] s5p_mfc_mmap+0x28/0xd4 [s5p_mfc]
[ 552.207459]
but task is already holding lock:
[ 552.213264] (&mm->mmap_sem){++++}, at: [<c01df2e4>] vm_mmap_pgoff+0x44/0xb8
[ 552.220284]
which lock already depends on the new lock.
[ 552.228429]
the existing dependency chain (in reverse order) is:
[ 552.235881]
-> #2 (&mm->mmap_sem){++++}:
[ 552.241259] __might_fault+0x80/0xb0
[ 552.245331] filldir64+0xc0/0x2f8
[ 552.249144] call_filldir+0xb0/0x14c
[ 552.253214] ext4_readdir+0x768/0x90c
[ 552.257374] iterate_dir+0x74/0x168
[ 552.261360] SyS_getdents64+0x7c/0x1a0
[ 552.265608] ret_fast_syscall+0x0/0x28
[ 552.269850]
-> #1 (&type->i_mutex_dir_key#2){++++}:
[ 552.276180] down_read+0x48/0x90
[ 552.279904] lookup_slow+0x74/0x178
[ 552.283889] walk_component+0x1a4/0x2e4
[ 552.288222] link_path_walk+0x174/0x4a0
[ 552.292555] path_openat+0x68/0x944
[ 552.296541] do_filp_open+0x60/0xc4
[ 552.300528] file_open_name+0xe4/0x114
[ 552.304772] filp_open+0x28/0x48
[ 552.308499] kernel_read_file_from_path+0x30/0x78
[ 552.313700] _request_firmware+0x3ec/0x78c
[ 552.318291] request_firmware+0x3c/0x54
[ 552.322642] s5p_mfc_load_firmware+0x54/0x150 [s5p_mfc]
[ 552.328358] s5p_mfc_open+0x4e4/0x550 [s5p_mfc]
[ 552.333394] v4l2_open+0xa0/0x104 [videodev]
[ 552.338137] chrdev_open+0xa4/0x18c
[ 552.342121] do_dentry_open+0x208/0x310
[ 552.346454] path_openat+0x28c/0x944
[ 552.350526] do_filp_open+0x60/0xc4
[ 552.354512] do_sys_open+0x118/0x1c8
[ 552.358586] ret_fast_syscall+0x0/0x28
[ 552.362830]
-> #0 (&dev->mfc_mutex){+.+.}:
-> #0 (&dev->mfc_mutex){+.+.}:
[ 552.368379] lock_acquire+0x6c/0x88
[ 552.372364] __mutex_lock+0x68/0xa34
[ 552.376437] mutex_lock_interruptible_nested+0x1c/0x24
[ 552.382086] s5p_mfc_mmap+0x28/0xd4 [s5p_mfc]
[ 552.386939] v4l2_mmap+0x54/0x88 [videodev]
[ 552.391601] mmap_region+0x3a8/0x638
[ 552.395673] do_mmap+0x330/0x3a4
[ 552.399400] vm_mmap_pgoff+0x90/0xb8
[ 552.403472] SyS_mmap_pgoff+0x90/0xc0
[ 552.407632] ret_fast_syscall+0x0/0x28
[ 552.411876]
other info that might help us debug this:
[ 552.419848] Chain exists of:
&dev->mfc_mutex --> &type->i_mutex_dir_key#2 --> &mm->mmap_sem
[ 552.431200] Possible unsafe locking scenario:
[ 552.437092] CPU0 CPU1
[ 552.441598] ---- ----
[ 552.446104] lock(&mm->mmap_sem);
[ 552.449484] lock(&type->i_mutex_dir_key#2);
[ 552.456329] lock(&mm->mmap_sem);
[ 552.462222] lock(&dev->mfc_mutex);
[ 552.465775]
*** DEADLOCK ***
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit baed3c4bc4 ]
_channel_ is being dereferenced before it is null checked, hence there is a
potential null pointer dereference. Fix this by moving the pointer dereference
after _channel_ has been null checked.
This issue was detected with the help of Coccinelle.
Fixes: c5f5d0f997 ("[media] c8sectpfe: STiH407/10 Linux DVB demux support")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a17d2d6cd9 ]
When used as part of a display pipeline, the VSP is stopped and
restarted explicitly by the DU from its suspend and resume handlers.
There is thus no need to stop or restart pipelines in the VSP suspend
and resume handlers, and doing so would cause the hardware to be
left in a misconfigured state.
Ensure that the VSP suspend and resume handlers do not affect DRM-based
pipelines.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5331aec1bf upstream.
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/media/platform/soc_camera/soc_scale_crop.o
see include/linux/module.h for more information
This adds the license as "GPL", which matches the header of the file.
MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ccbc1e3876 upstream.
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/media/platform/mtk-vcodec/mtk-vcodec-common.o
see include/linux/module.h for more information
This adds the license as "GPL v2", which matches the header of the file.
MODULE_DESCRIPTION is also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9917fbcfa2 ]
if output->wm_num is bigger than 2, the value for reg is
not initialized, as warned by smatch:
drivers/media/platform/qcom/camss-8x16/camss-vfe.c:633 vfe_set_xbar_cfg() error: uninitialized symbol 'reg'.
drivers/media/platform/qcom/camss-8x16/camss-vfe.c:637 vfe_set_xbar_cfg() error: uninitialized symbol 'reg'.
That shouldn't happen in practice, so add a logic that will
break the loop if i > 1, fixing the warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e69b987a97 upstream.
This addresses the wrong behavior of decoder stop command by
rewriting it. These new implementation enqueue an empty buffer
on the decoder input buffer queue to signal end-of-stream. The
client should stop queuing buffers on the V4L2 Output queue
and continue queuing/dequeuing buffers on Capture queue. This
process will continue until the client receives a buffer with
V4L2_BUF_FLAG_LAST flag raised, which means that this is last
decoded buffer with data.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5232c37ce2 upstream.
This fixes wrongly filled bytesused field of v4l2_plane structure
by include data_offset in the plane, Also fill data_offset and
bytesused for capture type of buffers only.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull media fixes from Mauro Carvalho Chehab:
"Core fixes:
- cec: Respond to unregistered initiators, when applicable
- dvb_frontend: only use kref after initialized
Driver-specific fixes:
- qcom, camss: Make function vfe_set_selection static
- qcom: VIDEO_QCOM_CAMSS should depend on HAS_DMA
- s5p-cec: add NACK detection support
- media: staging/imx: Fix uninitialized variable warning
- dib3000mc: i2c transfers over usb cannot be done from stack
- venus: init registered list on streamoff"
* tag 'media/v4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: dvb_frontend: only use kref after initialized
media: platform: VIDEO_QCOM_CAMSS should depend on HAS_DMA
media: cec: Respond to unregistered initiators, when applicable
media: s5p-cec: add NACK detection support
media: staging/imx: Fix uninitialized variable warning
media: qcom: camss: Make function vfe_set_selection static
media: venus: init registered list on streamoff
media: dvb: i2c transfers over usb cannot be done from stack
The s5p-cec driver returned CEC_TX_STATUS_ERROR for the NACK condition.
Some digging into the datasheet uncovered the S5P_CEC_TX_STAT1 register where
bit 0 indicates if the transmit was nacked or not.
Use this to return the correct CEC_TX_STATUS_NACK status to userspace.
This was the only driver that couldn't tell a NACK from another error, and
that was very unusual. And a potential problem for applications as well.
Tested with my Odroid-U3.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: <stable@vger.kernel.org> # for v4.12 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The function vfe_set_selection is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
warning: symbol 'vfe_set_selection' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pull dma-mapping updates from Christoph Hellwig:
- removal of the old dma_alloc_noncoherent interface
- remove unused flags to dma_declare_coherent_memory
- restrict OF DMA configuration to specific physical busses
- use the iommu mailing list for dma-mapping questions and patches
* tag 'dma-mapping-4.14' of git://git.infradead.org/users/hch/dma-mapping:
dma-coherent: fix dma_declare_coherent_memory() logic error
ARM: imx: mx31moboard: Remove unused 'dma' variable
dma-coherent: remove an unused variable
MAINTAINERS: use the iommu list for the dma-mapping subsystem
dma-coherent: remove the DMA_MEMORY_MAP and DMA_MEMORY_IO flags
dma-coherent: remove the DMA_MEMORY_INCLUDES_CHILDREN flag
of: restrict DMA configuration
dma-mapping: remove dma_alloc_noncoherent and dma_free_noncoherent
i825xx: switch to switch to dma_alloc_attrs
au1000_eth: switch to dma_alloc_attrs
sgiseeq: switch to dma_alloc_attrs
dma-mapping: reduce dma_mapping_error inline bloat
Pull media updates from Mauro Carvalho Chehab:
"Brazil's Independence Day pull request :-)
This is one of the biggest media pull requests, with 625 patches
affecting almost all parts of media (RC, DVB, V4L2, CEC, docs).
This contains:
- A lot of new drivers:
* DVB frontends: mxl5xx, stv0910, stv6111;
* camera flash: as3645a led driver;
* HDMI receiver: adv748X;
* camera sensor: Omnivision 6650 5M driver (ov6650);
* HDMI CEC: ao-cec meson driver;
* V4L2: Qualcom camss driver;
* Remote controller: gpio-ir-tx, pwm-ir-tx and zx-irdec drivers.
- The DDbridge DVB driver got a massive update, with makes it in sync
with modern hardware from that vendor;
- There's an important milestone on this series: the DVB
documentation was written in 2003, but only started to be updated
in 2007. It also used to contain several gaps from the time it was
kept out of tree, mentioning error codes and device nodes that
never existed upstream. On this series, it received a massive
update: all non-deprecated digital TV APIs are now in sync with the
current implementation;
- Some DVB APIs that aren't used by any upstream driver got removed;
- Other parts of the media documentation algo got updated, fixing
some bugs on its PDF output and making it compatible with Sphinx
version 1.6.
As the number of hacks required to build PDF output reduced, I hope
we'll have less troubles as newer versions of our documentation
toolchain are released (famous last words);
- As usual, lots of driver cleanups and improvements"
* tag 'media/v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (624 commits)
media: leds: as3645a: add V4L2_FLASH_LED_CLASS dependency
media: get rid of removed DMX_GET_CAPS and DMX_SET_SOURCE leftovers
media: Revert "[media] v4l: async: make v4l2 coexist with devicetree nodes in a dt overlay"
media: staging: atomisp: sh_css_calloc shall return a pointer to the allocated space
media: Revert "[media] lirc_dev: remove superfluous get/put_device() calls"
media: add qcom_camss.rst to v4l-drivers rst file
media: dvb headers: make checkpatch happier
media: dvb uapi: move frontend legacy API to another part of the book
media: pixfmt-srggb12p.rst: better format the table for PDF output
media: docs-rst: media: Don't use \small for V4L2_PIX_FMT_SRGGB10 documentation
media: index.rst: don't write "Contents:" on PDF output
media: pixfmt*.rst: replace a two dots by a comma
media: vidioc-g-fmt.rst: adjust table format
media: vivid.rst: add a blank line to correct ReST format
media: v4l2 uapi book: get rid of driver programming's chapter
media: format.rst: use the right markup for important notes
media: docs-rst: cardlists: change their format to flat-tables
media: em28xx-cardlist.rst: update to reflect last changes
media: v4l2-event.rst: adjust table to fit on PDF output
media: docs: don't show ToC for each part on PDF output
...
DMA_MEMORY_IO was never used in the tree, so remove it. That means there is
no need for the DMA_MEMORY_MAP flag either now, so remove it as well and
change dma_declare_coherent_memory to return a normal errno value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
platform_get_irq() may fail, so we should better check its return
value and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A debug printk statement was copied incorrectly into the new
csi1 parser code and causes a warning there:
drivers/media/platform/omap3isp/isp.c: In function 'isp_probe':
include/linux/dynamic_debug.h:134:3: error: 'i' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Since there is only one lane, the index is never set. This
changes the debug print to always print a zero instead,
keeping the original format of the message.
Fixes: 9211434bad ("media: omap3isp: Parse CSI1 configuration from the device tree")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix those warnings when building on i386:
drivers/media/platform/qcom/camss-8x16/camss-csiphy.c:333:22: warning: constant 1000000000000 is so big it is long long
drivers/media/platform/qcom/camss-8x16/camss-csiphy.c:339:32: warning: constant 1000000000000 is so big it is long long
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use standard V4L2 control to get pixel clock rate from a sensor
linked in the media controller pipeline. Then calculate clock
rates on CSIPHY, CSID and VFE to use the lowest possible.
If the currnet pixel clock rate of the sensor cannot be read then
use the highest possible. This case covers also the CSID test
generator usage.
If VFE is already powered on by another pipeline, check that the
current VFE clock rate is high enough for the new pipeline.
If not return busy error code as VFE clock rate cannot be changed
while VFE is running.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use VFE PIX input interface and do format conversion in VFE.
Supported input format is UYVY (single plane YUV 4:2:2) and
its different sample order variations.
Supported output formats are:
- NV12/NV21 (two plane YUV 4:2:0)
- NV16/NV61 (two plane YUV 4:2:2)
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add Makefile and update platform/Kconfig and platform/Makefile
to enable building of the QCom CAMSS driver.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These files control the VFE module. The VFE has different input
interfaces. The PIX input interface feeds the input data to an image
processing pipeline. Three RDI input interfaces bypass the image
processing pipeline. The VFE also contains the AXI bus interface which
writes the output data to memory.
RDI interfaces are supported in this version. PIX interface is not
supported.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These files control the ISPIF module which handles the routing of the data
streams from the CSIDs to the inputs of the VFE.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These files control the CSID modules which handle the protocol and
application layer of the CSI2 receivers.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These files control the CSIPHY modules which are responsible for the
physical layer of the CSI2 receivers.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
videobuf_queue_ops are not supposed to change at runtime. All functions
working with videobuf_queue_ops provided by <media/videobuf-core.h> work
with const videobuf_queue_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This change the alignment restriction for output type of buffers
only, also set corect input resolution and fill bidirectional
vb2 queue flag in order to map output type buffers read/write.
The last is needed by encoder firmware to add padding at the
bottom of output (input buffers).
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implements g_/s_selection crop support by using DCMI crop
hardware feature.
User can first get the maximum supported resolution of the sensor
by calling g_selection(V4L2_SEL_TGT_CROP_BOUNDS).
Then user call to s_selection(V4L2_SEL_TGT_CROP) will reset sensor
to its maximum resolution and crop request is saved for later usage
in s_fmt().
Next call to s_fmt() will check if sensor can do frame size request
with crop request. If sensor supports only discrete frame sizes,
the frame size which is larger than user request is selected in
order to be able to match the crop request. Then s_fmt() resolution
user request is adjusted to match crop request resolution.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
