commit de3004c874 upstream.
In preparation for removing security_old_inode_init_security(), switch to
security_inode_init_security().
Extend the existing ocfs2_initxattrs() to take the
ocfs2_security_xattr_info structure from fs_info, and populate the
name/value/len triple with the first xattr provided by LSMs.
As fs_info was not used before, ocfs2_initxattrs() can now handle the case
of replicating the behavior of security_old_inode_init_security(), i.e.
just obtaining the xattr, in addition to setting all xattrs provided by
LSMs.
Supporting multiple xattrs is not currently supported where
security_old_inode_init_security() was called (mknod, symlink), as it
requires non-trivial changes that can be done at a later time. Like for
reiserfs, even if EVM is invoked, it will not provide an xattr (if it is
not the first to set it, its xattr will be discarded; if it is the first,
it does not have xattrs to calculate the HMAC on).
Finally, since security_inode_init_security(), unlike
security_old_inode_init_security(), returns zero instead of -EOPNOTSUPP if
no xattrs were provided by LSMs or if inodes are private, additionally
check in ocfs2_init_security_get() if the xattr name is set.
If not, act as if security_old_inode_init_security() returned -EOPNOTSUPP,
and set si->enable to zero to notify to the functions following
ocfs2_init_security_get() that no xattrs are available.
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Casey Schaufler <casey@schaufler-ca.com>
Acked-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from upstream fc96ec826b)
On CPM, the RISC core is a lot more efficiant when doing transfers
in 16-bits chunks than in 8-bits chunks, but unfortunately the
words need to be byte swapped as seen in a previous commit.
So, for large tranfers with an even size, allocate a temporary tx
buffer and byte-swap data before and after transfer.
This change allows setting higher speed for transfer. For instance
on an MPC 8xx (CPM1 comms RISC processor), the documentation tells
that transfer in byte mode at 1 kbit/s uses 0.200% of CPM load
at 25 MHz while a word transfer at the same speed uses 0.032%
of CPM load. This means the speed can be 6 times higher in
word mode for the same CPM load.
For the time being, only do it on CPM1 as there must be a
trade-off between the CPM load reduction and the CPU load required
to byte swap the data.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/f2e981f20f92dd28983c3949702a09248c23845c.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(backported from upstream 8a5299a127)
For different reasons, fsl-spi driver performs bits_per_word
modifications for different reasons:
- On CPU mode, to minimise amount of interrupts
- On CPM/QE mode to work around controller byte order
For CPU mode that's done in fsl_spi_prepare_message() while
for CPM mode that's done in fsl_spi_setup_transfer().
Reunify all of it in fsl_spi_prepare_message(), and catch
impossible cases early through master's bits_per_word_mask
instead of returning EINVAL later.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/0ce96fe96e8b07cba0613e4097cfd94d09b8919a.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ca22da2fbd ]
William reports kernel soft-lockups on some OVS topologies when TC mirred
egress->ingress action is hit by local TCP traffic [1].
The same can also be reproduced with SCTP (thanks Xin for verifying), when
client and server reach themselves through mirred egress to ingress, and
one of the two peers sends a "heartbeat" packet (from within a timer).
Enqueueing to backlog proved to fix this soft lockup; however, as Cong
noticed [2], we should preserve - when possible - the current mirred
behavior that counts as "overlimits" any eventual packet drop subsequent to
the mirred forwarding action [3]. A compromise solution might use the
backlog only when tcf_mirred_act() has a nest level greater than one:
change tcf_mirred_forward() accordingly.
Also, add a kselftest that can reproduce the lockup and verifies TC mirred
ability to account for further packet drops after TC mirred egress->ingress
(when the nest level is 1).
[1] https://lore.kernel.org/netdev/33dc43f587ec1388ba456b4915c75f02a8aae226.1663945716.git.dcaratti@redhat.com/
[2] https://lore.kernel.org/netdev/Y0w%2FWWY60gqrtGLp@pop-os.localdomain/
[3] such behavior is not guaranteed: for example, if RPS or skb RX
timestamping is enabled on the mirred target device, the kernel
can defer receiving the skb and return NET_RX_SUCCESS inside
tcf_mirred_forward().
Reported-by: William Zhao <wizhao@redhat.com>
CC: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
[DP: adjusted context for linux-5.10.y]
Signed-off-by: Dragos-Marian Panait <dragos.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 78dcdffe04 ]
with commit e2ca070f89 ("net: sched: protect against stack overflow in
TC act_mirred"), act_mirred protected itself against excessive stack growth
using per_cpu counter of nested calls to tcf_mirred_act(), and capping it
to MIRRED_RECURSION_LIMIT. However, such protection does not detect
recursion/loops in case the packet is enqueued to the backlog (for example,
when the mirred target device has RPS or skb timestamping enabled). Change
the wording from "recursion" to "nesting" to make it more clear to readers.
CC: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: ca22da2fbd ("act_mirred: use the backlog for nested calls to mirred ingress")
Signed-off-by: Dragos-Marian Panait <dragos.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
5.10 stable commit 2b00b2a0e6 ("writeback, cgroup: fix null-ptr-deref
write in bdi_split_work_to_wbs") is a backport of upstream 6.3 commit
1ba1199ec5.
In the 5.10 stable commit backport percpu_ref_exit() is called twice:
first in cgwb_release_workfn() and then in cgwb_free_rcu(). The 2nd call
is benign as percpu_ref_exit() internally detects there's nothing to do.
This fixes an non-upstream issue that only applies to 5.10.y.
Fixes: 2b00b2a0e6 ("writeback, cgroup: fix null-ptr-deref write in bdi_split_work_to_wbs")
Signed-off-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4eda19cc8a upstream.
The watchdog countdown is supposed to begin when the device file is
opened. Instead, it would begin countdown upon the first write to or
close of the device file. Now, the ping operation is called within the
start operation which ensures the countdown begins. From experimenation,
it does not appear possible to do this with a single write including
both the start bit and the trigger bit. So, it is done as two distinct
writes.
Signed-off-by: Gregory Oakes <gregory.oakes@amd.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230316201312.17538-1-gregory.oakes@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2862a2fdfa ]
Use "a" constraint instead of "d" constraint to pass the state parameter to
the do_sqbs() inline assembly. This prevents that general purpose register
zero is used for the state parameter.
If the compiler would select general purpose register zero this would be
problematic for the used instruction in rsy format: the register used for
the state parameter is a base register. If the base register is general
purpose register zero the contents of the register are unexpectedly ignored
when the instruction is executed.
This only applies to z/VM guests using QIOASSIST with dedicated (pass through)
QDIO-based devices such as FCP [zfcp driver] as well as real OSA or
HiperSockets [qeth driver].
A possible symptom for this case using zfcp is the following repeating kernel
message pattern:
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: qdio: ZFCP on SC <sc> using AI:1 QEBSM:1 PRI:1 TDD:1 SIGA: W
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: A QDIO problem occurred
Each of the qdio problem message can be accompanied by the following entries
for the affected subchannel <sc> in
/sys/kernel/debug/s390dbf/qdio_error/hex_ascii for zfcp or qeth:
<sc> ccq: 69....
<sc> SQBS ERROR.
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Cc: Steffen Maier <maier@linux.ibm.com>
Fixes: 8129ee1642 ("[PATCH] s390: qdio V=V pass-through")
Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95d698869b ]
Possibly the last PCI controller-based (i.e. not a soft/winmodem)
dial-up modem one can still buy.
Looks to have a stock XR17C154 PCI UART chip for communication, but for
some reason when provisioning the PCI IDs they swapped the vendor and
subvendor IDs. Otherwise this card would have worked out of the box.
Searching online, some folks seem to not have this issue and others do,
so it is possible only some batches of cards have this error.
Create a new macro to handle the switched IDs and add support here.
Signed-off-by: Andrew Davis <afd@ti.com>
Cc: stable <stable@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230420160209.28221-1-afd@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 94b179052f upstream.
Prox-out events may not be reliably sent by some AES firmware. This can
cause problems for users, particularly due to arbitration logic disabling
touch input while the pen is in prox.
This commit adds a timer which is reset every time a new prox event is
received. When the timer expires we check to see if the pen is still in
prox and force it out if necessary. This is patterend off of the same
solution used by 'hid-letsketch' driver which has a similar problem.
Link: https://github.com/linuxwacom/input-wacom/issues/310
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66b2ca0862 upstream.
It was reported that soft dirty tracking doesn't work when using the
Radix MMU.
The tracking is supposed to work by clearing the soft dirty bit for a
mapping and then write protecting the PTE. If/when the page is written
to, a page fault occurs and the soft dirty bit is added back via
pte_mkdirty(). For example in wp_page_reuse():
entry = maybe_mkwrite(pte_mkdirty(entry), vma);
if (ptep_set_access_flags(vma, vmf->address, vmf->pte, entry, 1))
update_mmu_cache(vma, vmf->address, vmf->pte);
Unfortunately on radix _PAGE_SOFTDIRTY is being dropped by
radix__ptep_set_access_flags(), called from ptep_set_access_flags(),
meaning the soft dirty bit is not set even though the page has been
written to.
Fix it by adding _PAGE_SOFTDIRTY to the set of bits that are able to be
changed in radix__ptep_set_access_flags().
Fixes: b0b5e9b130 ("powerpc/mm/radix: Add radix pte #defines")
Cc: stable@vger.kernel.org # v4.7+
Reported-by: Dan Horák <dan@danny.cz>
Link: https://lore.kernel.org/r/20230511095558.56663a50f86bdc4cd97700b7@danny.cz
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230511114224.977423-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed40866ec7 upstream.
s390's struct statfs and struct statfs64 contain padding, which
field-by-field copying does not set. Initialize the respective structs
with zeros before filling them and copying them to userspace, like it's
already done for the compat versions of these structs.
Found by KMSAN.
[agordeev@linux.ibm.com: fixed typo in patch description]
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Link: https://lore.kernel.org/r/20230504144021.808932-2-iii@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 262d7a52ba upstream.
Under certain circumstances we send two EFLUSH commands, resulting in two
EFLUSH ack packets, while only expecting a single EFLUSH ack.
This can cause the driver Tx flush completion to get out of sync.
To avoid this problem, don't enable the "Transmit buffer flush done" (TFD)
interrupt and remove the code handling it.
Now we only send EFLUSH command after receiving status packet with
"Init detected" (IDET) bit set.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20230516134318.104279-6-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c0f4f09c0 upstream.
The CDC-ECM specification [1] requires to send the host MAC address as
an uppercase hexadecimal string in chapter "5.4 Ethernet Networking
Functional Descriptor":
The Unicode character is chosen from the set of values 30h through
39h and 41h through 46h (0-9 and A-F).
However, snprintf(.., "%pm", ..) generates a lowercase MAC address
string. While most host drivers are tolerant to this, UsbNcm.sys on
Windows 10 is not. Instead it uses a different MAC address with all
bytes set to zero including and after the first byte containing a
lowercase letter. On Windows 11 Microsoft fixed it, but apparently they
did not backport the fix.
This change fixes the issue by upper-casing the MAC to comply with the
specification.
[1]: https://www.usb.org/document-library/class-definitions-communication-devices-12, file ECM120.pdf
Fixes: bcd4a1c40b ("usb: gadget: u_ether: construct with default values and add setters/getters")
Cc: stable@vger.kernel.org
Signed-off-by: Konrad Gräfe <k.graefe@gateware.de>
Link: https://lore.kernel.org/r/20230505143640.443014-1-k.graefe@gateware.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a398d5eac6 upstream.
With faulty usb-storage devices, read/write can timeout, in that case
the SCSI layer will abort and re-issue the command. USB storage has no
internal timeout, it relies on SCSI layer aborting commands via
.eh_abort_handler() for non those responsive devices.
After two consecutive timeouts of the same command, SCSI layer calls
.eh_device_reset_handler(), without calling .eh_abort_handler() first.
With usb-storage, this causes a deadlock:
-> .eh_device_reset_handler
-> device_reset
-> mutex_lock(&(us->dev_mutex));
mutex already by usb_stor_control_thread(), which is waiting for
command completion:
-> usb_stor_control_thread (mutex taken here)
-> usb_stor_invoke_transport
-> usb_stor_Bulk_transport
-> usb_stor_bulk_srb
-> usb_stor_bulk_transfer_sglist
-> usb_sg_wait
Make sure we cancel any pending command in .eh_device_reset_handler()
to avoid this.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Cc: linux-usb@vger.kernel.org
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/all/ZEllnjMKT8ulZbJh@sakura/
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230505114759.1189741-1-mbizon@freebox.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 89dcd87ce5 ]
When CONFIG_BRIDGE_VLAN_FILTERING is disabled, two functions are still
defined but have no prototype or caller. This causes a W=1 warning for
the missing prototypes:
net/bridge/br_netlink_tunnel.c:29:6: error: no previous prototype for 'vlan_tunid_inrange' [-Werror=missing-prototypes]
net/bridge/br_netlink_tunnel.c:199:5: error: no previous prototype for 'br_vlan_tunnel_info' [-Werror=missing-prototypes]
The functions are already contitional on CONFIG_BRIDGE_VLAN_FILTERING,
and I coulnd't easily figure out the right set of #ifdefs, so just
move the declarations out of the #ifdef to avoid the warning,
at a small cost in code size over a more elaborate fix.
Fixes: 188c67dd19 ("net: bridge: vlan options: add support for tunnel id dumping")
Fixes: 569da08228 ("net: bridge: vlan options: add support for tunnel mapping set/del")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230516194625.549249-3-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61ae320a29 ]
There is no guarantee that rb_prev() will not return NULL in nft_rbtree_gc_elem():
general protection fault, probably for non-canonical address 0xdffffc0000000003: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000018-0x000000000000001f]
nft_add_set_elem+0x14b0/0x2990
nf_tables_newsetelem+0x528/0xb30
Furthermore, there is a possible use-after-free while iterating,
'node' can be free'd so we need to cache the next value to use.
Fixes: c9e6978e27 ("netfilter: nft_set_rbtree: Switch to node list walk for overlap detection")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60d758659f ]
In igb_hash_mc_addr() the expression:
"mc_addr[4] >> 8 - bit_shift", right shifting "mc_addr[4]"
shift by more than 7 bits always yields zero, so hash becomes not so different.
Add initialization with bit_shift = 1 and add a loop condition to ensure
bit_shift will be always in [1..8] range.
Fixes: 9d5c824399 ("igb: PCI-Express 82575 Gigabit Ethernet driver")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
