__u16 sco_pkt_type is introduced to struct sockaddr_sco. It allows bitwise
selection of SCO/eSCO packet types. Currently those bits are:
0x0001 HV1 may be used.
0x0002 HV2 may be used.
0x0004 HV3 may be used.
0x0008 EV3 may be used.
0x0010 EV4 may be used.
0x0020 EV5 may be used.
0x0040 2-EV3 may be used.
0x0080 3-EV3 may be used.
0x0100 2-EV5 may be used.
0x0200 3-EV5 may be used.
This is similar to the Packet Type parameter in the HCI Setup Synchronous
Connection Command, except that we are not reversing the logic on the EDR bits.
This makes the use of sco_pkt_tpye forward portable for the use case of
white-listing packet types, which we expect will be the primary use case.
If sco_pkt_type is zero, or userspace uses the old struct sockaddr_sco,
then the default behavior is to allow all packet types.
Packet type selection is just a request made to the Bluetooth chipset, and
it is up to the link manager on the chipset to negiotiate and decide on the
actual packet types used. Furthermore, when a SCO/eSCO connection is eventually
made there is no way for the host stack to determine which packet type was used
(however it is possible to get the link type of SCO or eSCO).
sco_pkt_type is ignored for incoming SCO connections. It is possible
to add this in the future as a parameter to the Accept Synchronous Connection
Command, however its a little trickier because the kernel does not
currently preserve sockaddr_sco data between userspace calls to accept().
The most common use for sco_pkt_type will be to white-list only SCO packets,
which can be done with the hci.h constant SCO_ESCO_MASK.
This patch is motivated by broken Bluetooth carkits such as the Motorolo
HF850 (it claims to support eSCO, but will actually reject eSCO connections
after 5 seconds) and the 2007/2008 Infiniti G35/37 (fails to route audio
if a 2-EV5 packet type is negiotiated). With this patch userspace can maintain
a list of compatible packet types to workaround remote devices such as these.
Based on a patch by Marcel Holtmann.
Rebased to 2.6.39.
Change-Id: Ide1c89574fa4f6f1b9218282e1af17051eb86315
Signed-off-by: Nick Pelly <npelly@google.com>
PPP handles packet loss but does not work with out of order packets.
This change performs reordering of incoming data packets within a
sliding window of one second. Since sequence number is optional,
receiving a packet without it will drop all queued packets.
Currently the logic is triggered by incoming packets, so queued
packets have to wait till another packet is arrived. It is done for
simplicity since no additional locks or threads are required. For
reliable protocols, a retransmission will kick it. For unreliable
protocols, queued packets just seem like packet loss. Time-critical
protocols might be broken, but they never work with queueing anyway.
Signed-off-by: Chia-chi Yeh <chiachi@android.com>
On Linux, when an interface goes down all its IPv6
addresses are deleted, so relying on knowing the previous
IPv6 addresses on the interface is brittle. Instead,
support nuking all sockets that are bound to IP addresses
that are not configured and up on the system. This
behaviour is triggered by specifying the unspecified
address (:: or 0.0.0.0). If an IP address is specified, the
behaviour is unchanged, except the ioctl now supports IPv6
as well as IPv4.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Based on the list of enabled USB functions, we can now switch the vendor ID
as well as the product ID.
Signed-off-by: Mike Lockwood <lockwood@android.com>
This reverts commit f0b0e4bec1.
The reverted commit incorrectly calculates the size of eMMC
devices in some (all?) cases.
This revert may cause problems in cases where the bootloader was
bug-compatible and puts a GPT partition at the incorrect end of
the eMMC device.
Signed-off-by: Colin Cross <ccross@android.com>
synchronize_rcu can be very expensive, averaging 100 ms in
some cases. In cgroup_attach_task, it is used to prevent
a task->cgroups pointer dereferenced in an RCU read side
critical section from being invalidated, by delaying the
call to put_css_set until after an RCU grace period.
To avoid the call to synchronize_rcu, make the put_css_set
call rcu-safe by moving the deletion of the css_set links
into free_css_set_work, scheduled by the rcu callback
free_css_set_rcu.
The decrement of the cgroup refcount is no longer
synchronous with the call to put_css_set, which can result
in the cgroup refcount staying positive after the last call
to cgroup_attach_task returns. To allow the cgroup to be
deleted with cgroup_rmdir synchronously after
cgroup_attach_task, have rmdir check the refcount of all
associated css_sets. If cgroup_rmdir is called on a cgroup
for which the css_sets all have refcount zero but the
cgroup refcount is nonzero, reuse the rmdir waitqueue to
block the rmdir until free_css_set_work is called.
Signed-off-by: Colin Cross <ccross@android.com>
Changes the meaning of CGRP_RELEASABLE to be set on any cgroup
that has ever had a task or cgroup in it, or had css_get called
on it. The bit is set in cgroup_attach_task, cgroup_create,
and __css_get. It is not necessary to set the bit in
cgroup_fork, as the task is either in the root cgroup, in
which can never be released, or the task it was forked from
already set the bit in croup_attach_task.
Signed-off-by: Colin Cross <ccross@android.com>
This governor is designed for latency-sensitive workloads, such as
interactive user interfaces. The interactive governor aims to be
significantly more responsive to ramp CPU quickly up when CPU-intensive
activity begins.
Existing governors sample CPU load at a particular rate, typically
every X ms. This can lead to under-powering UI threads for the period of
time during which the user begins interacting with a previously-idle system
until the next sample period happens.
The 'interactive' governor uses a different approach. Instead of sampling
the CPU at a specified rate, the governor will check whether to scale the
CPU frequency up soon after coming out of idle. When the CPU comes out of
idle, a timer is configured to fire within 1-2 ticks. If the CPU is very
busy from exiting idle to when the timer fires then we assume the CPU is
underpowered and ramp to MAX speed.
If the CPU was not sufficiently busy to immediately ramp to MAX speed, then
the governor evaluates the CPU load since the last speed adjustment,
choosing the highest value between that longer-term load or the short-term
load since idle exit to determine the CPU speed to ramp to.
A realtime thread is used for scaling up, giving the remaining tasks the
CPU performance benefit, unlike existing governors which are more likely to
schedule rampup work to occur after your performance starved tasks have
completed.
The tuneables for this governor are:
/sys/devices/system/cpu/cpufreq/interactive/min_sample_time:
The minimum amount of time to spend at the current frequency before
ramping down. This is to ensure that the governor has seen enough
historic CPU load data to determine the appropriate workload.
Default is 80000 uS.
/sys/devices/system/cpu/cpufreq/interactive/go_maxspeed_load
The CPU load at which to ramp to max speed. Default is 85.
Change-Id: Ib2b362607c62f7c56d35f44a9ef3280f98c17585
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Bug: 3152864
the csd sector count reported by eMMC 4.3+ cards includes the boot
partition size; subtract this from the size reported to the disk
since the boot partition is inaccessible
Change-Id: I601b83aa0159b7aa446409ea8c945b256dd0b5b1
Signed-off-by: Gary King <gking@nvidia.com>
Platform must register cpu power function that return power in
milliWatt seconds.
Change-Id: I1caa0335e316c352eee3b1ddf326fcd4942bcbe8
Signed-off-by: Mike Chan <mike@android.com>
Introduce new platform callback hooks for cpuacct for tracking CPU frequencies
Not all platforms / architectures have a set CPU_FREQ_TABLE defined
for CPU transition speeds. In order to track time spent in at various
CPU frequencies, we enable platform callbacks from cpuacct for this accounting.
Architectures that support overclock boosting, or don't have pre-defined
frequency tables can implement their own bucketing system that makes sense
given their cpufreq scaling abilities.
New file:
cpuacct.cpufreq reports the CPU time (in nanoseconds) spent at each CPU
frequency.
Change-Id: I10a80b3162e6fff3a8a2f74dd6bb37e88b12ba96
Signed-off-by: Mike Chan <mike@android.com>
Originally written by HTC. Contributions by Motorola and AKM.
misc: Import akm8975 from Motorola
Major style and code cleanups by Praveen Bharathi <pbharathi@motorola.com>
misc: akm8975: clean up code violations in akm8975.c
misc: akm8975: Clean up coding style, add suspend and resume
Change-Id: I4196913f15aec2dfbed47506d3dc085aada8e92d
Signed-off-by: Dima Zavin <dima@android.com>
When enabled, tracks the frequency of network transmissions
(inbound and outbound) and buckets them accordingly.
Buckets are determined by time between network activity.
Each bucket represents the number of network transmisions that were
N sec or longer apart. Where N is defined as 1 << bucket index.
This network pattern tracking is particularly useful for wireless
networks (ie: 3G) where batching network activity closely together
is more power efficient than far apart.
New file: /proc/net/stat/activity
output:
Min Bucket(sec) Count
1 7
2 0
4 1
8 0
16 0
32 2
64 1
128 0
Change-Id: I4c4cd8627b872a55f326b1715c51bc3bdd6e8d92
Signed-off-by: Mike Chan <mike@android.com>
This patch adds a notifier which can be used by subsystems that may
be interested in when a task has completely died and is about to
have it's last resource freed.
The Android lowmemory killer uses this to determine when a task
it has killed has finally given up its goods.
Signed-off-by: San Mehat <san@google.com>
Legacy pairing is a bit of a problem because on the incoming end it is
impossible to know pairing has begun:
2009-09-18 18:29:24.115692 > HCI Event: Connect Request (0x04) plen 10
bdaddr 00:23:D4:04:51:7A class 0x58020c type ACL
2009-09-18 18:29:24.115966 < HCI Command: Accept Connection Request (0x01|0x0009) plen 7
bdaddr 00:23:D4:04:51:7A role 0x00
Role: Master
2009-09-18 18:29:24.117065 > HCI Event: Command Status (0x0f) plen 4
Accept Connection Request (0x01|0x0009) status 0x00 ncmd 1
2009-09-18 18:29:24.282928 > HCI Event: Role Change (0x12) plen 8
status 0x00 bdaddr 00:23:D4:04:51:7A role 0x00
Role: Master
2009-09-18 18:29:24.291534 > HCI Event: Connect Complete (0x03) plen 11
status 0x00 handle 1 bdaddr 00:23:D4:04:51:7A type ACL encrypt 0x00
2009-09-18 18:29:24.291839 < HCI Command: Read Remote Supported Features (0x01|0x001b) plen 2
handle 1
2009-09-18 18:29:24.292144 > HCI Event: Page Scan Repetition Mode Change (0x20) plen 7
bdaddr 00:23:D4:04:51:7A mode 1
2009-09-18 18:29:24.293823 > HCI Event: Command Status (0x0f) plen 4
Read Remote Supported Features (0x01|0x001b) status 0x00 ncmd 1
2009-09-18 18:29:24.303588 > HCI Event: Max Slots Change (0x1b) plen 3
handle 1 slots 5
2009-09-18 18:29:24.309448 > HCI Event: Read Remote Supported Features (0x0b) plen 11
status 0x00 handle 1
Features: 0xff 0xff 0x2d 0xfe 0x9b 0xff 0x79 0x83
2009-09-18 18:29:24.345916 < HCI Command: Remote Name Request (0x01|0x0019) plen 10
bdaddr 00:23:D4:04:51:7A mode 2 clkoffset 0x0000
2009-09-18 18:29:24.346923 > HCI Event: Command Status (0x0f) plen 4
Remote Name Request (0x01|0x0019) status 0x00 ncmd 1
2009-09-18 18:29:24.375793 > HCI Event: Remote Name Req Complete (0x07) plen 255
status 0x00 bdaddr 00:23:D4:04:51:7A name 'test'
2009-09-18 18:29:34.332190 < HCI Command: Disconnect (0x01|0x0006) plen 3
handle 1 reason 0x13
There are some mainline patches such as "Add different pairing timeout for
Legacy Pairing" but they do not address the HCI sequence above.
I think the real solution is to avoid using CreateBond(), and instead make
the profile connection immediately. This way both sides will use a longer
timeout because there is a higher level connection in progress, and we will
not end up with the useless HCI sequence above.
Signed-off-by: Nick Pelly <npelly@google.com>
This provides kernel_debugger() which can be called from an interrupt
context low level debugger wedge to execute commands that inspect
kernel state. It doesn't do much on its own.
Signed-off-by: Brian Swetland <swetland@google.com>
kernel_debugger_core: Add sysrq command.
sysrq <c> will run the sysrq command <c> and dump what
was added to the kernel log while the command ran.
Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Arve Hjønnevåg <arve@android.com>
net: Fix a bitmask in PPPoPNS and rename constants in PPPoPNS and PPPoLAC.
Signed-off-by: Chia-chi Yeh <chiachi@android.com>
net: Fix a potential deadlock while releasing PPPoLAC/PPPoPNS socket.
PPP driver guarantees that no thread will be executing start_xmit() after
returning from ppp_unregister_channel(). To achieve this, a spinlock (downl)
is used. In pppolac_release(), ppp_unregister_channel() is called after sk_udp
is locked. At the same time, another thread might be running in pppolac_xmit()
with downl. Thus a deadlock will occur if the thread tries to lock sk_udp.
The same situation might happen on sk_raw in pppopns_release().
Signed-off-by: Chia-chi Yeh <chiachi@android.com>
net: Force PPPoLAC and PPPoPNS to bind an interface before creating PPP channel.
It is common to manipulate the routing table after configuring PPP device.
Since both PPPoLAC and PPPoPNS run over IP, care must be taken to make sure
that there is no loop in the routing table.
Although this can be done by adding a host route, it might still cause
problems when the interface is down for some reason.
To solve this, this patch forces both drivers to bind an interface before
creating PPP channel, so the system will not re-route the tunneling sockets
to another interface when the original one is down. Another benefit is that
now the host route is no longer required, so there is no need to remove it
when PPP channel is closed.
Signed-off-by: Chia-chi Yeh <chiachi@android.com>
net: Avoid sleep-inside-spinlock in PPPoLAC and PPPoPNS.
Since recv() and xmit() are called with a spinlock held, routines which might
sleep cannot be used. This issue is solved by following changes:
Incoming packets are now processed in backlog handler, recv_core(), instead of
recv(). Since backlog handler is always executed with socket spinlock held, the
requirement of ppp_input() is still satisfied.
Outgoing packets are now processed in workqueue handler, xmit_core(), instead of
xmit(). Note that kernel_sendmsg() is no longer used to prevent touching dead
sockets.
In release(), lock_sock() and pppox_unbind_sock() ensure that no thread is in
recv_core() or xmit(). Then socket handlers are restored before release_sock(),
so no packets will leak in backlog queue.
Signed-off-by: Chia-chi Yeh <chiachi@android.com>
net: Fix msg_iovlen in PPPoLAC and PPPoPNS.
Although any positive value should work (which is always true in both drivers),
the correct value should be 1.
Signed-off-by: Chia-chi Yeh <chiachi@android.com>
- Added multiple ACM instance support in Android gadget
- Fixed multiple instance naming issue in ACM function
- Increased max instances from 4 to 8
Change-Id: I65f1b0be94da859bab7ec0ad7cd804b896c7c4c5
Signed-off-by: John Michelau <john.michelau@motorola.com>
For backward compatibility with PTP, MTP is limited to a 32-bit file size.
When transferring files greater than 4 gig, MTP uses 0xFFFFFFFF as the file size
and the receiver reads until it receives a short packet.
Expanded size of mtp_file_range.length to 64 bits and added support for
writing zero length packets.
Signed-off-by: Mike Lockwood <lockwood@android.com>
Use this rather than calling usb_gadget_disconnect and usb_gadget_connect
directly to avoid sending USB disconnect events to userspace when resetting
the bus.
Signed-off-by: Mike Lockwood <lockwood@android.com>
Add switch to notify current USB configuration. This can be used to detect
USB connect and disconnect events.
Broadcast a change via the usb_composite class when a USB function is
enabled or disabled.
Rename usb_function.hidden to usb_function.disabled.
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: android gadget: add remote wakeup attribute to android function
Add remote wakeup attribute to configuration descriptor of android
function to advertise remote wakeup capability to host
Acked-by: Allam, Suresh Reddy <sallam@qualcomm.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: gadget: android: Allow functions to handle setup requests.
Signed-off-by: Mike Lockwood <lockwood@android.com>
Support for specifying the list of USB functions from platform data.
The main android.c gadget driver no longer has hard coded references
to the mass_storage and adb functions.
Support for computing the product ID based on tables in platform data
and the currently enabled functions.
Moved the adb enable/disable logic from android.c to f_adb.c.
Change-Id: I6259d3fb1473ed973f700e55d17744956f3527bb
Signed-off-by: Mike Lockwood <lockwood@android.com>
Change-Id: I4101540916b73a5f4e48684727ff782f98b969c7
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: android gadget: add remote wakeup attribute to android function
Add remote wakeup attribute to configuration descriptor of android
function to advertise remote wakeup capability to host
Acked-by: Allam, Suresh Reddy <sallam@qualcomm.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb gadget: link fixes for android composite gadget
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb gadget: Fix null pointer errors in android composite driver
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: android: Allow usb charging to draw up to 500mA instead of 250.
Signed-off-by: Rebecca Schultz Zavin <rebecca@android.com>
usb gadget: android: Add helper function for usb_gadget_connect and disconnect.
Signed-off-by: Mike Lockwood <lockwood@android.com>
drivers: usb: gadget: call switch_dev_unregister in mass storage unbind callback
This fixes a problem unloading the android gadget driver when built as a module
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: android: Add dependency on switch driver.
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: gadget: android: Fix USB WHQL Certification Issues
Submitted on behalf of RaviKumar Vembu <ravi.v@motorola.com>
Signed-off-by: Jared Suttles <jared.suttles@motorola.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
drivers: usb: gadget: Add "usb_mass_storage" platform driver.
This will be used for configuring vendor, product and release from board file.
Submitted on behalf of RaviKumar Vembu <ravi.v@motorola.com>
Signed-off-by: Jared Suttles <jared.suttles@motorola.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
drivers: usb: gadget: Use usb_mass_storage platform device as parent for lun
If a platform device is specified for the f_mass_storage function, use it as the
parent driver for the lun files in sysfs.
This allows a platform independent file path for controlling USB mass storage
from user space.
Signed-off-by: Mike Lockwood <lockwood@android.com>
drivers: usb: gadget: Add platform data struct for usb_mass_storage device
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: mass_storage: Fix Mass Storage Panic during PC reboot
Submitted on behalf of RaviKumar Vembu <ravi.v@motorola.com>
Signed-off-by: Jared Suttles <jared.suttles@motorola.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: f_mass_storage: Handle setup request correctly
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: f_mass_storage: Clean up wakelocks on error paths
Signed-off-by: Rebecca Schultz Zavin <rebecca@android.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
A card driver can now specify that the underlying bus should *not*
auto-resume with the rest of the system. This is useful for reducing resume
latency as well as saving power when the card driver is not using the
bus. In the future, we'll add support for manual suspend
Signed-off-by: San Mehat <san@google.com>
This is required to support chips which use SDIO for signaling/
communication but do not implement the various card enumeration registers
as required for full SD / SDIO cards.
mmc: sdio: Fix bug where we're freeing the CIS tables we never allocated when using EMBEDDED_SDIO
mmc: Add max_blksize to embedded SDIO data
Signed-off-by: San Mehat <san@google.com>
