When guest time is reset with KVM_SET_CLOCK(0), it is possible for
'hv_clock->system_time' to become a small negative number. This happens
because in KVM_SET_CLOCK handling we set 'kvm->arch.kvmclock_offset' based
on get_kvmclock_ns(kvm) but when KVM_REQ_CLOCK_UPDATE is handled,
kvm_guest_time_update() does (masterclock in use case):
hv_clock.system_time = ka->master_kernel_ns + v->kvm->arch.kvmclock_offset;
And 'master_kernel_ns' represents the last time when masterclock
got updated, it can precede KVM_SET_CLOCK() call. Normally, this is not a
problem, the difference is very small, e.g. I'm observing
hv_clock.system_time = -70 ns. The issue comes from the fact that
'hv_clock.system_time' is stored as unsigned and 'system_time / 100' in
compute_tsc_page_parameters() becomes a very big number.
Use 'master_kernel_ns' instead of get_kvmclock_ns() when masterclock is in
use and get_kvmclock_base_ns() when it's not to prevent 'system_time' from
going negative.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210331124130.337992-2-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
pvclock_gtod_sync_lock can be taken with interrupts disabled if the
preempt notifier calls get_kvmclock_ns to update the Xen
runstate information:
spin_lock include/linux/spinlock.h:354 [inline]
get_kvmclock_ns+0x25/0x390 arch/x86/kvm/x86.c:2587
kvm_xen_update_runstate+0x3d/0x2c0 arch/x86/kvm/xen.c:69
kvm_xen_update_runstate_guest+0x74/0x320 arch/x86/kvm/xen.c:100
kvm_xen_runstate_set_preempted arch/x86/kvm/xen.h:96 [inline]
kvm_arch_vcpu_put+0x2d8/0x5a0 arch/x86/kvm/x86.c:4062
So change the users of the spinlock to spin_lock_irqsave and
spin_unlock_irqrestore.
Reported-by: syzbot+b282b65c2c68492df769@syzkaller.appspotmail.com
Fixes: 30b5c851af ("KVM: x86/xen: Add support for vCPU runstate information")
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is no need to include changes to vcpu->requests into
the pvclock_gtod_sync_lock critical section. The changes to
the shared data structures (in pvclock_update_vm_gtod_copy)
already occur under the lock.
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fixing nested_vmcb_check_save to avoid all TOC/TOU races
is a bit harder in released kernels, so do the bare minimum
by avoiding that EFER.SVME is cleared. This is problematic
because svm_set_efer frees the data structures for nested
virtualization if EFER.SVME is cleared.
Also check that EFER.SVME remains set after a nested vmexit;
clearing it could happen if the bit is zero in the save area
that is passed to KVM_SET_NESTED_STATE (the save area of the
nested state corresponds to the nested hypervisor's state
and is restored on the next nested vmexit).
Cc: stable@vger.kernel.org
Fixes: 2fcf4876ad ("KVM: nSVM: implement on demand allocation of the nested state")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Avoid races between check and use of the nested VMCB controls. This
for example ensures that the VMRUN intercept is always reflected to the
nested hypervisor, instead of being processed by the host. Without this
patch, it is possible to end up with svm->nested.hsave pointing to
the MSR permission bitmap for nested guests.
This bug is CVE-2021-29657.
Reported-by: Felix Wilhelm <fwilhelm@google.com>
Cc: stable@vger.kernel.org
Fixes: 2fcf4876ad ("KVM: nSVM: implement on demand allocation of the nested state")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The page table of AMDGPU requires an alignment to CPU page so we should
check ioctl parameters for it. Return -EINVAL if some parameter is
unaligned to CPU page, instead of corrupt the page table sliently.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Xi Ruoyao <xry111@mengyan1223.wang>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Do the same thing we do for Renoir. We can check, but since
the sbios has started DPM, it will always return true which
causes the driver to skip some of the SMU init when it shouldn't.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Amdgpu driver uses 4-byte data type as DQM fence memory,
and transmits GPU address of fence memory to microcode
through query status PM4 message. However, query status
PM4 message definition and microcode processing are all
processed according to 8 bytes. Fence memory only allocates
4 bytes of memory, but microcode does write 8 bytes of memory,
so there is a memory corruption.
Changes since v1:
* Change dqm->fence_addr as a u64 pointer to fix this issue,
also fix up query_status and amdkfd_fence_wait_timeout function
uses 64 bit fence value to make them consistent.
Signed-off-by: Qu Huang <jinsdb@126.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
For multiple split bios, if one of the bio is fail, the whole
should return error to application. But we found there is a race
between bio_integrity_verify_fn and bio complete, which return
io success to application after one of the bio fail. The race as
following:
split bio(READ) kworker
nvme_complete_rq
blk_update_request //split error=0
bio_endio
bio_integrity_endio
queue_work(kintegrityd_wq, &bip->bip_work);
bio_integrity_verify_fn
bio_endio //split bio
__bio_chain_endio
if (!parent->bi_status)
<interrupt entry>
nvme_irq
blk_update_request //parent error=7
req_bio_endio
bio->bi_status = 7 //parent bio
<interrupt exit>
parent->bi_status = 0
parent->bi_end_io() // return bi_status=0
The bio has been split as two: split and parent. When split
bio completed, it depends on kworker to do endio, while
bio_integrity_verify_fn have been interrupted by parent bio
complete irq handler. Then, parent bio->bi_status which have
been set in irq handler will overwrite by kworker.
In fact, even without the above race, we also need to conside
the concurrency beteen mulitple split bio complete and update
the same parent bi_status. Normally, multiple split bios will
be issued to the same hctx and complete from the same irq
vector. But if we have updated queue map between multiple split
bios, these bios may complete on different hw queue and different
irq vector. Then the concurrency update parent bi_status may
cause the final status error.
Suggested-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20210331115359.1125679-1-yuyufen@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
xdp_return_frame() may be called outside of NAPI context to return
xdpf back to page_pool. xdp_return_frame() calls __xdp_return() with
napi_direct = false. For page_pool memory model, __xdp_return() calls
xdp_return_frame_no_direct() unconditionally and below false negative
kernel BUG throw happened under preempt-rt build:
[ 430.450355] BUG: using smp_processor_id() in preemptible [00000000] code: modprobe/3884
[ 430.451678] caller is __xdp_return+0x1ff/0x2e0
[ 430.452111] CPU: 0 PID: 3884 Comm: modprobe Tainted: G U E 5.12.0-rc2+ #45
Changes in v2:
- This patch fixes the issue by making xdp_return_frame_no_direct() is
only called if napi_direct = true, as recommended for better by
Jesper Dangaard Brouer. Thanks!
Fixes: 2539650fad ("xdp: Helpers for disabling napi_direct of xdp_return_frame")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit f211ac1545.
We had similar attempt in the past, and we reverted it.
History:
64a146513f [NET]: Revert incorrect accept queue backlog changes.
8488df894d [NET]: Fix bugs in "Whether sock accept queue is full" checking
I am adding a fat comment so that future attempts will
be much harder.
Fixes: f211ac1545 ("net: correct sk_acceptq_is_full()")
Cc: iuyacan <yacanliu@163.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5 fixes 2021-03-31
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2021-03-31
1) Fix ipv4 pmtu checks for xfrm anf vti interfaces.
From Eyal Birger.
2) There are situations where the socket passed to
xfrm_output_resume() is not the same as the one
attached to the skb. Use the socket passed to
xfrm_output_resume() to avoid lookup failures
when xfrm is used with VRFs.
From Evan Nimmo.
3) Make the xfrm_state_hash_generation sequence counter per
network namespace because but its write serialization
lock is also per network namespace. Write protection
is insufficient otherwise.
From Ahmed S. Darwish.
4) Fixup sctp featue flags when used with esp offload.
From Xin Long.
5) xfrm BEET mode doesn't support fragments for inner packets.
This is a limitation of the protocol, so no fix possible.
Warn at least to notify the user about that situation.
From Xin Long.
6) Fix NULL pointer dereference on policy lookup when
namespaces are uses in combination with esp offload.
7) Fix incorrect transformation on esp offload when
packets get segmented at layer 3.
8) Fix some user triggered usages of WARN_ONCE in
the xfrm compat layer.
From Dmitry Safonov.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In rds_message_map_pages, the rm is freed by rds_message_put(rm).
But rm is still used by rm->data.op_sg in return value.
My patch assigns ERR_CAST(rm->data.op_sg) to err before the rm is
freed to avoid the uaf.
Fixes: 7dba92037b ("net/rds: Use ERR_PTR for rds_message_alloc_sgs()")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a short network outage, the dst_entry is timed out and put
in DST_OBSOLETE_DEAD. We are in this code because arp reply comes
from this neighbour after network recovers. There is a potential
race condition that dst_entry is still in DST_OBSOLETE_DEAD.
With that, another neighbour lookup causes more harm than good.
In best case all packets in arp_queue are lost. This is
counterproductive to the original goal of finding a better path
for those packets.
I observed a worst case with 4.x kernel where a dst_entry in
DST_OBSOLETE_DEAD state is associated with loopback net_device.
It leads to an ethernet header with all zero addresses.
A packet with all zero source MAC address is quite deadly with
mac80211, ath9k and 802.11 block ack. It fails
ieee80211_find_sta_by_ifaddr in ath9k (xmit.c). Ath9k flushes tx
queue (ath_tx_complete_aggr). BAW (block ack window) is not
updated. BAW logic is damaged and ath9k transmission is disabled.
Signed-off-by: Tong Zhu <zhutong@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XSK wakeup flow triggers an IRQ by posting a NOP WQE and hitting
the doorbell on the async ICOSQ.
It maintains its state so that it doesn't issue another NOP WQE
if it has an outstanding one already.
For this flow to work properly, the NOP post must not fail.
Make sure to reserve room for the NOP WQE in all WQE posts to the
async ICOSQ.
Fixes: 8d94b590f1 ("net/mlx5e: Turn XSK ICOSQ into a general asynchronous one")
Fixes: 1182f36593 ("net/mlx5e: kTLS, Add kTLS RX HW offload support")
Fixes: 0419d8c9d8 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Current algorithm for encap keys is legacy from initial vxlan
implementation and doesn't take into account all possible fields of a
tunnel. For example, for a Geneve tunnel, which may have additional TLV
options, they are ignored when comparing encap keys and a rule can be
attached to an incorrect encap entry.
Fix that by introducing encap_info_equal() operation in
struct mlx5e_tc_tunnel. Geneve tunnel type uses custom implementation,
which extends generic algorithm and considers options if they are set.
Fixes: 7f1a546e32 ("net/mlx5e: Consider tunnel type for encap contexts")
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Calculating the number of compeltion EQs based on the number of
available IRQ vectors doesn't work now that all async EQs share one IRQ.
Thus the max number of EQs can be exceeded on systems with more than
approximately 256 CPUs. Take this into account when calculating the
number of available completion EQs.
Fixes: 81bfa20603 ("net/mlx5: Use a single IRQ for all async EQs")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Some TLS RX counters increment per socket/connection, and are not
protected against parallel modifications from several cores.
Switch them to atomic counters by taking them out of the RQ stats into
the global atomic TLS stats.
In this patch, we touch 'rx_tls_ctx/del' that count the number of
device-offloaded RX TLS connections added/deleted.
These counters are updated in the add/del callbacks, out of the fast
data-path.
This change is not needed for counters that increment only in NAPI
context, as they are protected by the NAPI mechanism.
Keep them as tls_* counters under 'struct mlx5e_rq_stats'.
Fixes: 76c1e1ac2a ("net/mlx5e: kTLS, Add kTLS RX stats")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Some TLS TX counters increment per socket/connection, and are not
protected against parallel modifications from several cores.
Switch them to atomic counters by taking them out of the SQ stats into
the global atomic TLS stats.
In this patch, we touch a single counter 'tx_tls_ctx' that counts the
number of device-offloaded TX TLS connections added.
Now that this counter can be increased without the for having the SQ
context in hand, move it to the mlx5e_ktls_add_tx() callback where it
really belongs, out of the fast data-path.
This change is not needed for counters that increment only in NAPI
context or under the TX lock, as they are already protected.
Keep them as tls_* counters under 'struct mlx5e_sq_stats'.
Fixes: d2ead1f360 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Create send to vport miss group was added in order to support traffic
recirculation to root table with metadata source rewrite.
This group is created also in case source rewrite isn't supported.
Fixed by creating send to vport miss group only if source rewrite is
supported by FW.
Fixes: 8e404fefa5 ("net/mlx5e: Match recirculated packet miss in slow table using reg_c1")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Use connector_type read from PTYS register when it's valid, based on
corresponding capability bit.
Fixes: 5b4793f817 ("net/mlx5e: Add support for reading connector type from PTYS")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Delete auxiliary bus drivers flow deletes the eth driver
first and then the eth-reps driver but eth-reps devices resources
are depend on eth device.
Fixed by changing the delete order of auxiliary bus drivers to delete
the eth-rep driver first and after it the eth driver.
Fixes: 601c10c89c ("net/mlx5: Delete custom device management logic")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
ct_label 0 is a default label each flow has and therefore
there can be rules that match on ct_label=0 without a prior
rule that set the ct_label to this value.
The ct_label value is not used directly in the HW rules and
instead it is mapped to some id within a defined range and this
id is used to set and match the metadata register which carries
the ct_label.
If we have a rule that matches on ct_label=0, the hw rule will
perform matching on a value that is != 0 because of the mapping
from label to id. Since the metadata register default value is
0 and it was never set before to anything else by an action that
sets the ct_label, there will always be a mismatch between that
register and the value in the rule.
To support such rule, a forced mapping of ct_label 0 to id=0
is done so that it will match the metadata register default
value of 0.
Fixes: 54b154ecfb ("net/mlx5e: CT: Map 128 bits labels to 32 bit map ID")
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Pull ftrace fix from Steven Rostedt:
"Add check of order < 0 before calling free_pages()
The function addresses that are traced by ftrace are stored in pages,
and the size is held in a variable. If there's some error in creating
them, the allocate ones will be freed. In this case, it is possible
that the order of pages to be freed may end up being negative due to a
size of zero passed to get_count_order(), and then that negative
number will cause free_pages() to free a very large section.
Make sure that does not happen"
* tag 'trace-v5.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Check if pages were allocated before calling free_pages()
Pull pin control fixes from Linus Walleij:
"Some overly ripe fixes for the v5.12 kernel. I should have sent
earlier but had my head stuck in GDB.
All are driver fixes:
- Fix up some Intel GPIO base calculations.
- Fix a register offset in the Microchip driver.
- Fix suspend/resume bug in the Rockchip driver.
- Default pull up strength in the Qualcomm LPASS driver.
- Fix two pingroup offsets in the Qualcomm SC7280 driver.
- Fix SDC1 register offset in the Qualcomm SC7280 driver.
- Fix a nasty string concatenation in the Qualcomm SDX55 driver.
- Check the REVID register to see if the device is real or
virtualized during virtualization in the Intel driver"
* tag 'pinctrl-v5.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: intel: check REVID register value for device presence
pinctrl: qcom: fix unintentional string concatenation
pinctrl: qcom: sc7280: Fix SDC1_RCLK configurations
pinctrl: qcom: sc7280: Fix SDC_QDSD_PINGROUP and UFS_RESET offsets
pinctrl: qcom: lpass lpi: use default pullup/strength values
pinctrl: rockchip: fix restore error in resume
pinctrl: microchip-sgpio: Fix wrong register offset for IRQ trigger
pinctrl: intel: Show the GPIO base calculation explicitly
card->owner is a required property and since commit 81033c6b58 ("ALSA:
core: Warn on empty module") a warning is issued if it is empty. Add it.
This fixes following warning observed on Lamobo R1:
WARNING: CPU: 1 PID: 190 at sound/core/init.c:207 snd_card_new+0x430/0x480 [snd]
Modules linked in: sun4i_codec(E+) sun4i_backend(E+) snd_soc_core(E) ...
CPU: 1 PID: 190 Comm: systemd-udevd Tainted: G C E 5.10.0-1-armmp #1 Debian 5.10.4-1
Hardware name: Allwinner sun7i (A20) Family
Call trace:
(snd_card_new [snd])
(snd_soc_bind_card [snd_soc_core])
(snd_soc_register_card [snd_soc_core])
(sun4i_codec_probe [sun4i_codec])
Fixes: 45fb6b6f2a ("ASoC: sunxi: add support for the on-chip codec on early Allwinner SoCs")
Related: commit 3c27ea23ff ("ASoC: qcom: Set card->owner to avoid warnings")
Related: commit ec653df2a0 ("drm/vc4/vc4_hdmi: fill ASoC card owner")
Cc: linux-arm-kernel@lists.infradead.org
Cc: alsa-devel@alsa-project.org
Signed-off-by: Bastian Germann <bage@linutronix.de>
Link: https://lore.kernel.org/r/20210331151843.30583-1-bage@linutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
I dunno why I got added here, but I haven't been using this driver for
years. Remove me to make space for interested parties.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Only send "X1000_I2C_DC_STOP" when last byte, or it will cause
error when I2C write operation which should look like this:
device_addr + w, reg_addr, data;
But without this patch, it looks like this:
device_addr + w, reg_addr, device_addr + w, data;
Fixes: 21575a7a8d ("I2C: JZ4780: Add support for the X1000.")
Reported-by: 杨文龙 (Yang Wenlong) <ywltyut@sina.cn>
Tested-by: 杨文龙 (Yang Wenlong) <ywltyut@sina.cn>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commit 924a9bc362 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct")
added a call to dev_parse_header_protocol() but mac_header is not yet set.
This means that eth_hdr() reads complete garbage, and syzbot complained about it [1]
This patch resets mac_header earlier, to get more coverage about this change.
Audit of virtio_net_hdr_to_skb() callers shows that this change should be safe.
[1]
BUG: KASAN: use-after-free in eth_header_parse_protocol+0xdc/0xe0 net/ethernet/eth.c:282
Read of size 2 at addr ffff888017a6200b by task syz-executor313/8409
CPU: 1 PID: 8409 Comm: syz-executor313 Not tainted 5.12.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x141/0x1d7 lib/dump_stack.c:120
print_address_description.constprop.0.cold+0x5b/0x2f8 mm/kasan/report.c:232
__kasan_report mm/kasan/report.c:399 [inline]
kasan_report.cold+0x7c/0xd8 mm/kasan/report.c:416
eth_header_parse_protocol+0xdc/0xe0 net/ethernet/eth.c:282
dev_parse_header_protocol include/linux/netdevice.h:3177 [inline]
virtio_net_hdr_to_skb.constprop.0+0x99d/0xcd0 include/linux/virtio_net.h:83
packet_snd net/packet/af_packet.c:2994 [inline]
packet_sendmsg+0x2325/0x52b0 net/packet/af_packet.c:3031
sock_sendmsg_nosec net/socket.c:654 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:674
sock_no_sendpage+0xf3/0x130 net/core/sock.c:2860
kernel_sendpage.part.0+0x1ab/0x350 net/socket.c:3631
kernel_sendpage net/socket.c:3628 [inline]
sock_sendpage+0xe5/0x140 net/socket.c:947
pipe_to_sendpage+0x2ad/0x380 fs/splice.c:364
splice_from_pipe_feed fs/splice.c:418 [inline]
__splice_from_pipe+0x43e/0x8a0 fs/splice.c:562
splice_from_pipe fs/splice.c:597 [inline]
generic_splice_sendpage+0xd4/0x140 fs/splice.c:746
do_splice_from fs/splice.c:767 [inline]
do_splice+0xb7e/0x1940 fs/splice.c:1079
__do_splice+0x134/0x250 fs/splice.c:1144
__do_sys_splice fs/splice.c:1350 [inline]
__se_sys_splice fs/splice.c:1332 [inline]
__x64_sys_splice+0x198/0x250 fs/splice.c:1332
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
Fixes: 924a9bc362 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Balazs Nemeth <bnemeth@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not be advertising EEE for modes that we do not support,
correct that oversight by looking at the PHY device supported linkmodes.
Fixes: 99cec8a4dd ("net: phy: broadcom: Allow enabling or disabling of EEE")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A merge hint message needs some time to process before the merged
flow actually reaches the firmware, during which we may get duplicate
merge hints if there're more than one packet that hit the pre-merged
flow. And processing duplicate merge hints will cost extra host_ctx's
which are a limited resource.
Avoid the duplicate merge by using hash table to store the sub_flows
to be merged.
Fixes: 8af56f40e5 ("nfp: flower: offload merge flows")
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc/net/nf_conntrack shows icmpv6 as unknown.
Fixes: 09ec82f5af ("netfilter: conntrack: remove protocol name from l4proto struct")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
syzbot is reporting NULL pointer dereference at reiserfs_security_init()
[1], for commit ab17c4f021 ("reiserfs: fixup xattr_root caching")
is assuming that REISERFS_SB(s)->xattr_root != NULL in
reiserfs_xattr_jcreate_nblocks() despite that commit made
REISERFS_SB(sb)->priv_root != NULL && REISERFS_SB(s)->xattr_root == NULL
case possible.
I guess that commit 6cb4aff0a7 ("reiserfs: fix oops while creating
privroot with selinux enabled") wanted to check xattr_root != NULL
before reiserfs_xattr_jcreate_nblocks(), for the changelog is talking
about the xattr root.
The issue is that while creating the privroot during mount
reiserfs_security_init calls reiserfs_xattr_jcreate_nblocks which
dereferences the xattr root. The xattr root doesn't exist, so we get
an oops.
Therefore, update reiserfs_xattrs_initialized() to check both the
privroot and the xattr root.
Link: https://syzkaller.appspot.com/bug?id=8abaedbdeb32c861dc5340544284167dd0e46cde # [1]
Reported-and-tested-by: syzbot <syzbot+690cb1e51970435f9775@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 6cb4aff0a7 ("reiserfs: fix oops while creating privroot with selinux enabled")
Acked-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Jan Kara <jack@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the mentioned helper can end-up freeing the socket wmem
without waking-up any processes waiting for more write memory.
If the partially orphaned skb is attached to an UDP (or raw) socket,
the lack of wake-up can hang the user-space.
Even for TCP sockets not calling the sk destructor could have bad
effects on TSQ.
Address the issue using skb_orphan to release the sk wmem before
setting the new sock_efree destructor. Additionally bundle the
whole ownership update in a new helper, so that later other
potential users could avoid duplicate code.
v1 -> v2:
- use skb_orphan() instead of sort of open coding it (Eric)
- provide an helper for the ownership change (Eric)
Fixes: f6ba8d33cf ("netem: fix skb_orphan_partial()")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sch_htb: fix null pointer dereference on a null new_q
Currently if new_q is null, the null new_q pointer will be
dereference when 'q->offload' is true. Fix this by adding
a braces around htb_parent_to_leaf_offload() to avoid it.
Addresses-Coverity: ("Dereference after null check")
Fixes: d03b195b5a ("sch_htb: Hierarchical QoS hardware offload")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't call into get_signal() with the sqd mutex held, it'll fail if we're
freezing the task and we'll get complaints on locks still being held:
====================================
WARNING: iou-sqp-8386/8387 still has locks held!
5.12.0-rc4-syzkaller #0 Not tainted
------------------------------------
1 lock held by iou-sqp-8386/8387:
#0: ffff88801e1d2470 (&sqd->lock){+.+.}-{3:3}, at: io_sq_thread+0x24c/0x13a0 fs/io_uring.c:6731
stack backtrace:
CPU: 1 PID: 8387 Comm: iou-sqp-8386 Not tainted 5.12.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x141/0x1d7 lib/dump_stack.c:120
try_to_freeze include/linux/freezer.h:66 [inline]
get_signal+0x171a/0x2150 kernel/signal.c:2576
io_sq_thread+0x8d2/0x13a0 fs/io_uring.c:6748
Fold the get_signal() case in with the parking checks, as we need to drop
the lock in both cases, and since we need to be checking for parking when
juggling the lock anyway.
Reported-by: syzbot+796d767eb376810256f5@syzkaller.appspotmail.com
Fixes: dbe1bdbb39 ("io_uring: handle signals for IO threads like a normal thread")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, action creation using ACT API in replace mode is buggy.
When invoking for non-existent action index 42,
tc action replace action bpf obj foo.o sec <xyz> index 42
kernel creates the action, fills up the netlink response, and then just
deletes the action after notifying userspace.
tc action show action bpf
doesn't list the action.
This happens due to the following sequence when ovr = 1 (replace mode)
is enabled:
tcf_idr_check_alloc is used to atomically check and either obtain
reference for existing action at index, or reserve the index slot using
a dummy entry (ERR_PTR(-EBUSY)).
This is necessary as pointers to these actions will be held after
dropping the idrinfo lock, so bumping the reference count is necessary
as we need to insert the actions, and notify userspace by dumping their
attributes. Finally, we drop the reference we took using the
tcf_action_put_many call in tcf_action_add. However, for the case where
a new action is created due to free index, its refcount remains one.
This when paired with the put_many call leads to the kernel setting up
the action, notifying userspace of its creation, and then tearing it
down. For existing actions, the refcount is still held so they remain
unaffected.
Fortunately due to rtnl_lock serialization requirement, such an action
with refcount == 1 will not be concurrently deleted by anything else, at
best CLS API can move its refcount up and down by binding to it after it
has been published from tcf_idr_insert_many. Since refcount is atleast
one until put_many call, CLS API cannot delete it. Also __tcf_action_put
release path already ensures deterministic outcome (either new action
will be created or existing action will be reused in case CLS API tries
to bind to action concurrently) due to idr lock serialization.
We fix this by making refcount of newly created actions as 2 in ACT API
replace mode. A relaxed store will suffice as visibility is ensured only
after the tcf_idr_insert_many call.
Note that in case of creation or overwriting using CLS API only (i.e.
bind = 1), overwriting existing action object is not allowed, and any
such request is silently ignored (without error).
The refcount bump that occurs in tcf_idr_check_alloc call there for
existing action will pair with tcf_exts_destroy call made from the
owner module for the same action. In case of action creation, there
is no existing action, so no tcf_exts_destroy callback happens.
This means no code changes for CLS API.
Fixes: cae422f379 ("net: sched: use reference counting action init")
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
