Currently we are trying to enable/disable the clk of irq's gpio bank when
unmask/mask irq. But the kernel's "lazy disable approach" will skip masking
irq when the irq chip doesn't support irq_disable ops.
So we may hit this case:
irq_enable-> enable clk
irq_disable-> noop
irq_enable-> enable clk again
irq_disable-> noop
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit d468289a02)
Change-Id: Ibe2f5c4ef48425300355a46312215984d8f4e1bc
when the work clock is the same as the bus clock.drop
the "clock-names" property as the PWM uses only one
clock (the driver now needs to call devm_clk_get with NULL).
Change-Id: I7fcdd9635f81778a3dc522d99d0fc081408d6fea
Signed-off-by: Xinhuang Li <buluess.li@rock-chips.com>
Introduce status node in debugfs to show HDMI output status,
such as phy status, color and eotf.
Here is a sample log:
PHY enabled Mode: HDMI
Pixel Clk: 594000000Hz TMDS Clk: 594000000Hz
Color Format: YUV422 Color Depth: 10 bit
Colorimetry: ITU.BT2020 EOTF: ST2084
x0: 0 y0: 0
x1: 0 y1: 0
x2: 0 y2: 0
white x: 0 white y: 0
max lum: 0 min lum: 0
max cll: 0 max fall: 0
Change-Id: I5d458b633dd3bd9aab67cc91f1695621937e58f5
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>
* linux-linaro-lsk-v4.4-android: (510 commits)
Linux 4.4.103
Revert "sctp: do not peel off an assoc from one netns to another one"
xen: xenbus driver must not accept invalid transaction ids
s390/kbuild: enable modversions for symbols exported from asm
ASoC: wm_adsp: Don't overrun firmware file buffer when reading region data
btrfs: return the actual error value from from btrfs_uuid_tree_iterate
ASoC: rsnd: don't double free kctrl
netfilter: nf_tables: fix oob access
netfilter: nft_queue: use raw_smp_processor_id()
spi: SPI_FSL_DSPI should depend on HAS_DMA
staging: iio: cdc: fix improper return value
iio: light: fix improper return value
mac80211: Suppress NEW_PEER_CANDIDATE event if no room
mac80211: Remove invalid flag operations in mesh TSF synchronization
drm: Apply range restriction after color adjustment when allocation
ALSA: hda - Apply ALC269_FIXUP_NO_SHUTUP on HDA_FIXUP_ACT_PROBE
ath10k: set CTS protection VDEV param only if VDEV is up
ath10k: fix potential memory leak in ath10k_wmi_tlv_op_pull_fw_stats()
ath10k: ignore configuring the incorrect board_id
ath10k: fix incorrect txpower set by P2P_DEVICE interface
...
Conflicts:
drivers/media/v4l2-core/v4l2-ctrls.c
kernel/sched/fair.c
Change-Id: I48152b2a0ab1f9f07e1da7823119b94f9b9e1751
[ Upstream commit 639b08810d ]
When accessing Xenstore in a transaction the user is specifying a
transaction id which he normally obtained from Xenstore when starting
the transaction. Xenstore is validating a transaction id against all
known transaction ids of the connection the request came in. As all
requests of a domain not being the one where Xenstore lives share
one connection, validation of transaction ids of different users of
Xenstore in that domain should be done by the kernel of that domain
being the multiplexer between the Xenstore users in that domain and
Xenstore.
In order to prohibit one Xenstore user "hijacking" a transaction from
another user the xenbus driver has to verify a given transaction id
against all known transaction ids of the user before forwarding it to
Xenstore.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 91ca1a8c58 ]
At the end of function ad7150_write_event_config(), directly returns 0.
As a result, the errors will be ignored by the callers. It may be better
to return variable "ret".
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit db4e5376d0 ]
In function cm3232_reg_init(), it returns 0 even if the last call to
i2c_smbus_write_byte_data() returns a negative value (indicates error).
As a result, the return value may be inconsistent with the execution
status, and the caller of cm3232_reg_init() will not be able to detect
the error. This patch fixes the bug.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188641
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 097e46d2ae ]
ath10k_wmi_tlv_op_pull_fw_stats() uses tb = ath10k_wmi_tlv_parse_alloc(...)
function, which allocates memory. If any of the three error-paths are
taken, this tb needs to be freed.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d2e202c06c ]
With command to get board_id from otp, in the case of following
boot get otp board id result 0x00000000 board_id 0 chip_id 0
boot using board name 'bus=pci,bmi-chip-id=0,bmi-board-id=0"
...
failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=0 from
ath10k/QCA6174/hw3.0/board-2.bin
The invalid board_id=0 will be used as index to search in the board-2.bin.
Ignore the case with board_id=0, as it means the otp is not carrying
the board id information.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 88407beb1b ]
Ath10k reports the phy capability that supports P2P_DEVICE interface.
When we use the P2P supported wpa_supplicant to start connection, it'll
create two interfaces, one is wlan0 (vdev_id=0) and one is P2P_DEVICE
p2p-dev-wlan0 which is for p2p control channel (vdev_id=1).
ath10k_pci mac vdev create 0 (add interface) type 2 subtype 0
ath10k_add_interface: vdev_id: 0, txpower: 0, bss_power: 0
...
ath10k_pci mac vdev create 1 (add interface) type 2 subtype 1
ath10k_add_interface: vdev_id: 1, txpower: 0, bss_power: 0
And the txpower in per vif bss_conf will only be set to valid tx power when
the interface is assigned with channel_ctx.
But this P2P_DEVICE interface will never be used for any connection, so
that the uninitialized bss_conf.txpower=0 is assinged to the
arvif->txpower when interface created.
Since the txpower configuration is firmware per physical interface.
So the smallest txpower of all vifs will be the one limit the tx power
of the physical device, that causing the low txpower issue on other
active interfaces.
wlan0: Limiting TX power to 21 (24 - 3) dBm
ath10k_pci mac vdev_id 0 txpower 21
ath10k_mac_txpower_recalc: vdev_id: 1, txpower: 0
ath10k_mac_txpower_recalc: vdev_id: 0, txpower: 21
ath10k_pci mac txpower 0
This issue only happens when we use the wpa_supplicant that supports
P2P or if we use the iw tool to create the control P2P_DEVICE interface.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fc318d64f3 ]
The zx_dma driver supports cyclic transfer mode. Let's set DMA_CYCLIC
cap_mask bit to make that clear, and avoid unnecessary failure when
clients request channel via dma_request_chan_by_mask() with DMA_CYCLIC
bit set in mask.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 977509f7c5 ]
Previously we didn't check the type of device before trying to apply Type 1
(PCI-X) or Type 2 (PCIe) Setting Records from _HPX.
We don't support PCI-X Setting Records, so this was harmless, but the
warning was useless.
We do support PCIe Setting Records, and we didn't check whether a device
was PCIe before applying settings. I don't think anything bad happened on
non-PCIe devices because pcie_capability_clear_and_set_word(),
pcie_cap_has_lnkctl(), etc., would fail before doing any harm. But it's
ugly to depend on those internals.
Check the device type before attempting to apply Type 1 and Type 2 Setting
Records (Type 0 records are applicable to PCI, PCI-X, and PCIe devices).
A side benefit is that this prevents useless "not supported" warnings when
a BIOS supplies a Type 1 (PCI-X) Setting Record and we try to apply it to
every single device:
pci 0000:00:00.0: PCI-X settings not supported
After this patch, we'll get the warning only when a BIOS supplies a Type 1
record and we have a PCI-X device to which it should be applied.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=187731
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19110cfbb3 upstream.
Lennart reported the following race condition:
\ e1000_watchdog_task
\ e1000e_has_link
\ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link
/* link is up */
mac->get_link_status = false;
/* interrupt */
\ e1000_msix_other
hw->mac.get_link_status = true;
link_active = !hw->mac.get_link_status
/* link_active is false, wrongly */
This problem arises because the single flag get_link_status is used to
signal two different states: link status needs checking and link status is
down.
Avoid the problem by using the return value of .check_for_link to signal
the link status to e1000e_has_link().
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cac9d2fb2 upstream.
VIDIOC_DQEVENT and VIDIOC_QUERY_EXT_CTRL should give the same output for
the control flags field.
This patch creates a new function user_flags(), that calculates the user
exported flags value (which is different than the kernel internal flags
structure). This function is then used by all the code that exports the
internal flags to userspace.
Reported-by: Dimitrios Katsaros <patcherwork@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e45067f94 upstream.
The ioctl LIRC_SET_REC_TIMEOUT would set a timeout of 704ns if called
with a timeout of 4294968us.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a9a17e3bb upstream.
This patch fixes an issue seen on Power systems with ixgbe which results
in skb list corruption and an eventual kernel oops. The following is what
was observed:
CPU 1 CPU2
============================ ============================
1: ixgbe_xmit_frame_ring ixgbe_clean_tx_irq
2: first->skb = skb eop_desc = tx_buffer->next_to_watch
3: ixgbe_tx_map read_barrier_depends()
4: wmb check adapter written status bit
5: first->next_to_watch = tx_desc napi_consume_skb(tx_buffer->skb ..);
6: writel(i, tx_ring->tail);
The read_barrier_depends is insufficient to ensure that tx_buffer->skb does not
get loaded prior to tx_buffer->next_to_watch, which then results in loading
a stale skb pointer. This patch replaces the read_barrier_depends with
smp_rmb to ensure loads are ordered with respect to the load of
tx_buffer->next_to_watch.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b8edcc685 upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with fm10k as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f72271e2a0 upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40evf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae0c585d93 upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with ixgbevf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e1f9ca546 upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igbvf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4cb99185b upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igb as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52c6912fde upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40e as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1fb354207 upstream.
For the same reason that /proc/iomem returns 0's for non-root readers
and acpi tables are root-only, make the 'resource' attribute for
namespace devices only readable by root. Otherwise we disclose physical
address information.
Fixes: bf9bccc14c ("libnvdimm: pmem label sets and namespace instantiation")
Reported-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b18d4b8a25 upstream.
The set of valid sequence numbers is {1,2,3}. The specification
indicates that an implementation should consider 0 a sign of a critical
error:
UEFI 2.7: 13.19 NVDIMM Label Protocol
Software never writes the sequence number 00, so a correctly
check-summed Index Block with this sequence number probably indicates a
critical error. When software discovers this case it treats it as an
invalid Index Block indication.
While the expectation is that the invalid block is just thrown away, the
Robustness Principle says we should fix this to make both sequence
numbers valid.
Fixes: f524bf271a ("libnvdimm: write pmem label set")
Reported-by: Juston Li <juston.li@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33ec6dbc5a upstream.
Fix child node-lookup during probe, which ended up searching the whole
device tree depth-first starting at parent rather than just matching on
its children.
Note that the original premature free of the parent node has already
been fixed separately, but that fix was apparently never backported to
stable.
Fixes: 9ac33b0ce8 ("CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)")
Fixes: 660e155193 ("clk: ti: dra7-atl-clock: Fix of_node reference counting")
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 660e155193 upstream.
of_find_node_by_name() will call of_node_put() on the node so we need to
get it first to avoid warnings.
The cfg_node needs to be put after we have finished processing the
properties.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
