We refer to TCP et al. symbols so have to use INET as
the dependency.
ERROR: "tcp_prot" [net/tls/tls.ko] undefined!
>> ERROR: "tcp_rate_check_app_limited" [net/tls/tls.ko] undefined!
ERROR: "tcp_register_ulp" [net/tls/tls.ko] undefined!
ERROR: "tcp_unregister_ulp" [net/tls/tls.ko] undefined!
ERROR: "do_tcp_sendpages" [net/tls/tls.ko] undefined!
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A 2 pixel wide pink strip was observed on the left end of some HDMI
monitors configured in a HDMI mode.
It turned out that we were missing out on configuring AVI infoframes, and
unlike APQ8064, the 8x96 HDMI H/W seems to be sensitive to that.
Add configuration of AVI infoframes. While at it, make sure that
hdmi_audio_update is only called when we've detected that the monitor
supports HDMI.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Without doing anything in unprepare, the HDMI driver isn't able to
switch modes successfully. Calling set_rate with a new rate results
in an un-locked PLL.
If we reset the PLL in unprepare, the PLL is able to lock with the
new rate.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Commit c0c0d9eeeb ("drm/msm: hdmi audio support") uses logical
OR operators to build up a value to be written in the
REG_HDMI_AUDIO_INFO0 and REG_HDMI_AUDIO_INFO1 registers when it
should have used bitwise operators.
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Fixes: c0c0d9eeeb ("drm/msm: hdmi audio support")
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that the msm_gem supports an arbitrary number of vma's, we no longer
need to assign an id (index) to each address space. So rip out the
associated code.
Signed-off-by: Rob Clark <robdclark@gmail.com>
It means we have to do a list traversal where we once had an index into
a table. But the list will normally have one or two entries.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Pull some of the logic out into msm_gem_new() (since we don't need to
care about the imported-bo case), and don't defer allocating pages. The
latter is generally a good idea, since if we are using VRAM carveout to
allocate contiguous buffers (ie. no IOMMU), the allocation is more
likely to fail. So failing at allocation time is a more sane option.
Plus this simplifies things in the next patch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
No functional change, that will come later. But this will make it
easier to deal with dynamically created address spaces (ie. per-
process pagetables for gpu).
Signed-off-by: Rob Clark <robdclark@gmail.com>
Before we can shift to passing the address-space object to _get_iova(),
we need to fix a few places (dsi+fbdev) that were hard-coding the adress
space id. That gets somewhat easier if we just move these to the kms
base class.
Prep work for next patch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
It serves no purpose, things should be sufficiently synchronized already
by atomic framework. And it is somewhat awkward to be holding a spinlock
when msm_gem_iova() is going to start needing to grab a mutex.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Most, but not all, paths where calling the with struct_mutex held. The
fast-path in msm_gem_get_iova() (plus some sub-code-paths that only run
the first time) was masking this issue.
So lets just always hold struct_mutex for hw_init(). And sprinkle some
WARN_ON()'s and might_lock() to avoid this sort of problem in the
future.
Signed-off-by: Rob Clark <robdclark@gmail.com>
memptrs->wptr seems to be unused. Remove it to avoid
confusing the upcoming preemption code.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The amount of information that we need to pass into msm_gpu_init()
is steadily increasing, so add a new struct to stabilize the function
call and make it easier to add new configuration down the line.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Modify the 'pad' member of struct drm_msm_gem_info to 'flags'. If the
user sets 'flags' to non-zero it means that they want a IOVA for the
GEM object instead of a mmap() offset. Return the iova in the 'offset'
member.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
[robclark: s/hint/flags in commit msg]
Signed-off-by: Rob Clark <robdclark@gmail.com>
The ioctl array is sparsely populated but the compiler will make sure
that it is sufficiently sized for all the values that we have so we
can safely use ARRAY_SIZE() instead of having a constantly changing
#define in the uapi header.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The A5XX GPU powers on in "secure" mode. In secure mode the GPU can
only render to buffers that are marked as secure and inaccessible
to the kernel and user through a series of hardware protections. In
practice secure mode is used to draw things like a UI on a secure
video frame.
In order to switch out of secure mode the GPU executes a special
shader that clears out the GMEM and other sensitve registers and
then writes a register. Because the kernel can't be trusted the
shader binary is signed and verified and programmed by the
secure world. To do this we need to read the MDT header and the
segments from the firmware location and put them in memory and
present them for approval.
For targets without secure support there is an out: if the
secure world doesn't support secure then there are no hardware
protections and we can freely write the SECVID_TRUST register from
the CPU. We don't have 100% confidence that we can query the
secure capabilities at run time but we have enough calls that
need to go right to give us some confidence that we're at least doing
something useful.
Of course if we guess wrong you trigger a permissions violation
which usually ends up in a system crash but thats a problem
that shows up immediately.
[v2: use child device per Bjorn]
[v3: use generic MDT loader per Bjorn]
[v4: use managed dma functions and ifdefs for the MDT loader]
[v5: Add depends for QCOM_MDT_LOADER]
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[robclark: fix Kconfig to use select instead of depends + #if IS_ENABLED()]
Signed-off-by: Rob Clark <robdclark@gmail.com>
Just a tidy up to follow the standard EXPORT_SYMBOL*() declarations
in order to improve grep-ability.
- Move EXPORT_SYMBOL*() to the position right after its definition
- Remove superfluous blank line before EXPORT_SYMBOL*() lines
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just a tidy up to follow the standard EXPORT_SYMBOL*() declarations
in order to improve grep-ability.
- Move EXPORT_SYMBOL*() to the position right after its definition
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just a tidy up to follow the standard EXPORT_SYMBOL*() declarations
in order to improve grep-ability.
- Move EXPORT_SYMBOL*() to the position right after its definition
- Remove superfluous blank line before EXPORT_SYMBOL*() lines
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just a tidy up to follow the standard EXPORT_SYMBOL*() declarations
in order to improve grep-ability.
- Remove superfluous blank line before EXPORT_SYMBOL*() lines
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, we only mark the CPU cache as dirty if we skip a clflush.
This leads to some confusion where we have to ask if the object is in
the write domain or missed a clflush. If we always mark the cache as
dirty, this becomes a much simply question to answer.
The goal remains to do as few clflushes as required and to do them as
late as possible, in the hope of deferring the work to a kthread and not
block the caller (e.g. execbuf, flips).
v2: Always call clflush before GPU execution when the cache_dirty flag
is set. This may cause some extra work on llc systems that migrate dirty
buffers back and forth - but we do try to limit that by only setting
cache_dirty at the end of the gpu sequence.
v3: Always mark the cache as dirty upon a level change, as we need to
invalidate any stale cachelines due to external writes.
Reported-by: Dongwon Kim <dongwon.kim@intel.com>
Fixes: a6a7cc4b7d ("drm/i915: Always flush the dirty CPU cache when pinning the scanout")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dongwon Kim <dongwon.kim@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Dongwon Kim <dongwon.kim@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615123850.26843-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Kishon writes:
phy: for 4.13
*) Group phy drivers into vendor specific directories
*) Add USB3 PHY driver for Renesas R-Car Gen3
*) Add USB2 PHY driver for Meson GXL and GXM SoCs
*) Add USB DRD PHY driver for Broadcom Northstar2
*) Add USB PHY driver for CPCAP PMIC USB
*) Make phy-meson8b-usb2 driver support USB PHY on Meson8
*) Make phy-tusb1210 driver support TUSB1211
*) Make phy-rockchip-inno-usb2 driver support usb2-phy in rk3228 SoCs
*) Make phy-brcm-sata driver support for stingray SATA phy
*) Make bcm-ns-usb3 as a MDIO driver
*) Make rockchip-inno-usb2 support two host ports
*) Implement ->set_mode() callback in phy-tusb1210
*) Minor fixes in phy drivers
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When a kthread calls call_usermodehelper() the steps are:
1. allocate current->mm
2. load_elf_binary()
3. populate current->thread.regs
While doing this, interrupts are not disabled. If there is a perf
interrupt in the middle of this process (i.e. step 1 has completed
but not yet reached to step 3) and if perf tries to read userspace
regs, kernel oops with following log:
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc0000000000da0fc
...
Call Trace:
perf_output_sample_regs+0x6c/0xd0
perf_output_sample+0x4e4/0x830
perf_event_output_forward+0x64/0x90
__perf_event_overflow+0x8c/0x1e0
record_and_restart+0x220/0x5c0
perf_event_interrupt+0x2d8/0x4d0
performance_monitor_exception+0x54/0x70
performance_monitor_common+0x158/0x160
--- interrupt: f01 at avtab_search_node+0x150/0x1a0
LR = avtab_search_node+0x100/0x1a0
...
load_elf_binary+0x6e8/0x15a0
search_binary_handler+0xe8/0x290
do_execveat_common.isra.14+0x5f4/0x840
call_usermodehelper_exec_async+0x170/0x210
ret_from_kernel_thread+0x5c/0x7c
Fix it by setting abi to PERF_SAMPLE_REGS_ABI_NONE when userspace
pt_regs are not set.
Fixes: ed4a4ef85c ("powerpc/perf: Add support for sampling interrupt register state")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CMA has gained a recent helper function for calculating the start
of a plane buffer's physical address. Use that instead of the
hand rolled version.
Cc: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
If an instance of Mali DP hardware shares the interrupt line with
another hardware (usually another instance of the Mali DP) its
interrupt handler can get called when the device is suspended.
Check the PM status before making access to the hardware registers
to avoid deadlocks.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Intel SST driver allocates lots of pages at suspend for saving the
firmware states, and this may occasionally lead to the allocation
error due to the high order, ending up with the suspend failure.
Use kvzalloc() so that it can fall back to vmalloc() gracefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Power9, trying to use data breakpoints throws the splat shown
below. This is because the check for a data breakpoint in DSISR is in
do_hash_page(), which is not called when in Radix mode.
Unable to handle kernel paging request for data at address 0xc000000000e19218
Faulting instruction address: 0xc0000000001155e8
cpu 0x0: Vector: 300 (Data Access) at [c0000000ef1e7b20]
pc: c0000000001155e8: find_pid_ns+0x48/0xe0
lr: c000000000116ac4: find_task_by_vpid+0x44/0x90
sp: c0000000ef1e7da0
msr: 9000000000009033
dar: c000000000e19218
dsisr: 400000
Move the check to handle_page_fault() so as to catch data breakpoints
in both Hash and Radix MMU modes.
We have to change the check in do_hash_page() against 0xa410 to use
0xa450, so as to include the value of (DSISR_DABRMATCH << 16).
There are two sites that call handle_page_fault() when in Radix, both
already pass DSISR in r4.
Fixes: caca285e5a ("powerpc/mm/radix: Use STD_MMU_64 to properly isolate hash related code")
Cc: stable@vger.kernel.org # v4.7+
Reported-by: Shriya R. Kulkarni <shriykul@in.ibm.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
[mpe: Fix the fall-through case on hash, we need to reload DSISR]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
ftrace_caller() depends on a modified regs->nip to detect if a certain
function has been livepatched. However, with KPROBES_ON_FTRACE, it is
possible for regs->nip to have been modified by the kprobes pre_handler
(jprobes, for instance). In this case, we do not want to invoke the
livepatch_handler so as not to consume the livepatch stack.
To distinguish between the two (kprobes and livepatch), we check if
there is an active kprobe on the current function. If there is, then we
know for sure that it must have modified the NIP as we don't support
livepatching a kprobe'd function. In this case, we simply skip the
livepatch_handler and branch to the new NIP. Otherwise, the
livepatch_handler is invoked.
Fixes: ead514d5fb ("powerpc/kprobes: Add support for KPROBES_ON_FTRACE")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For DYNAMIC_FTRACE_WITH_REGS, we should be passing-in the original set
of registers in pt_regs, to capture the state _before_ ftrace_caller.
However, we are instead passing the stack pointer *after* allocating a
stack frame in ftrace_caller. Fix this by saving the proper value of r1
in pt_regs. Also, use SAVE_10GPRS() to simplify the code.
Fixes: 153086644f ("powerpc/ftrace: Add support for -mprofile-kernel ftrace ABI")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This fixes a crash when function_graph and jprobes are used together.
This is essentially commit 237d28db03 ("ftrace/jprobes/x86: Fix
conflict between jprobes and function graph tracing"), but for powerpc.
Jprobes breaks function_graph tracing since the jprobe hook needs to use
jprobe_return(), which never returns back to the hook, but instead to
the original jprobe'd function. The solution is to momentarily pause
function_graph tracing before invoking the jprobe hook and re-enable it
when returning back to the original jprobe'd function.
Fixes: 6794c78243 ("powerpc64: port of the function graph tracer")
Cc: stable@vger.kernel.org # v2.6.30+
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull configfs updates from Christoph Hellwig:
"A fix from Nic for a race seen in production (including a stable tag).
And while I'm sending you this I'm also sneaking in a trivial new
helper from Bart so that we don't need inter-tree dependencies for the
next merge window"
* tag 'configfs-for-4.12' of git://git.infradead.org/users/hch/configfs:
configfs: Introduce config_item_get_unless_zero()
configfs: Fix race between create_link and configfs_rmdir
The Armada 7K and 8K SoCs use the same gpio controller as most of the
other mvebu SoCs. However, the main difference is that the GPIO
controller is part of a bigger system controller, and a syscon is used to
control the overall system controller. Therefore, the driver needs to be
adjusted to retrieve the regmap of the syscon to access registers, and
account for the fact that registers are located at a certain offset
within the regmap.
This commit add the support of the syscon and introduce a new variant for
this case.
It was based on the preliminary work of Thomas Petazzoni.
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds a pinctrl driver for the CP110 part of the Marvell
Armada 7K and 8K SoCs. The Armada 7K has a single CP110, where almost all
the MPP pins are available. On the other side, the Armada 8K has two
CP110, and the available MPPs are split between the master CP110 (MPPs 32
to 62) and the slave CP110 (MPPs 0 to 31).
The register interface to control the MPPs is however the same as all
other mvebu SoCs, so we can reuse the common pinctrl-mvebu.c logic.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Reviewed-by: Shadi Ammouri <shadi@marvell.com>
[updated for mvebu pinctrl and 4.9 changes:
- converted to simple_mmio
- converted to syscon/regmap
- removed unimplemented .remove function
- dropped DTS changes
- defered gpio ranges to DT
- fixed warning
- properly set soc->nmodes
-- rmk]
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[ add missing MPP[61:56] function 14 (SDIO)
-- Konstantin Porotchkin]
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
[ allow to properly register more then one instance of this driver
-- Grzegorz Jaszczyk]
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[ - rebased on 4.12-rc1
- fixed the 80 character limit for mvebu_mpp_mode array
- aligned the compatible name on the ones already used
- fixed the MPP table for CP110: some MPP are not available on Armada 7K
-- Gregory CLEMENT]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
