Incorrectly shifted relocation address will cause a lower memory
corruption and likely a hang on a write or a read of an arbitrary data
in case of IOMMU absence. As of now, there is no known use for the
address shifting and adding a proper shifts / sizes validation is a much
more work. Let's forbid shifts in the firewall till a proper validation
is implemented.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Erik Faye-Lund <kusmabite@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Perform gathers coping before patching them, so that original gathers are
left untouched. That's not as bad as leaking kernel addresses, but still
doesn't feel right.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In case of relocations / waitchecks patching failure the jobs pins stay
referenced till DRM file get closed, wasting memory. Add the missed
unpinning.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Erik Faye-Lund <kusmabite@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The commands stream is prepended by the jobs class on the CDMA
submission, so that explicitly setting a module class in the commands
stream isn't necessary. The firewall initializes its class to 0 and the
command stream that doesn't explicitly specify the class effectively
bypasses the firewall.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Erik Faye-Lund <kusmabite@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra20 if plane has width or height equal to 0, it will be infinitely
wide or tall. Let's disable the plane if it is invisible on atomic state
committing to fix the issue. The Rockchip DRM driver does the same.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Erik Faye-Lund <kusmabite@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra20 an overlay plane should be clipped, otherwise its output is
distorted once plane crosses display boundary.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Erik Faye-Lund <kusmabite@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit 33a8eb8d40 ("drm/tegra: dc: Implement runtime PM") introduced
HW reset control. It causes a hang on Tegra20 if both display
controllers are utilized (RGB panel and HDMI). The TRM suggests that
each display controller has its own reset control, apparently it is not
correct.
Fixes: 33a8eb8d40 ("drm/tegra: dc: Implement runtime PM")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Erik Faye-Lund <kusmabite@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In case of invalid syncpoint ID, the host1x_syncpt_get() returns NULL and
none of its users perform a check of the returned pointer later. Let's bail
out until it's too late.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The waitchecks along with multiple syncpoints per submit are not ready
for use yet, let's forbid them for now.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If commands buffer claims a number of words that is higher than its BO can
fit, a kernel OOPS will be fired on the out-of-bounds BO access. This was
triggered by an opentegra Xorg driver that erroneously pushed too many
commands to the pushbuf.
The CDMA commands buffer address is 4 bytes aligned, so check its
alignment.
The maximum number of the CDMA gather fetches is 16383, add a check for
it.
Add a sanity check for the relocations in a same way.
[ 46.829393] Unable to handle kernel paging request at virtual address f09b2000
...
[<c04a3ba4>] (host1x_job_pin) from [<c04dfcd0>] (tegra_drm_submit+0x474/0x510)
[<c04dfcd0>] (tegra_drm_submit) from [<c04deea0>] (tegra_submit+0x50/0x6c)
[<c04deea0>] (tegra_submit) from [<c04c07c0>] (drm_ioctl+0x1e4/0x3ec)
[<c04c07c0>] (drm_ioctl) from [<c02541a0>] (do_vfs_ioctl+0x9c/0x8e4)
[<c02541a0>] (do_vfs_ioctl) from [<c0254a1c>] (SyS_ioctl+0x34/0x5c)
[<c0254a1c>] (SyS_ioctl) from [<c0107640>] (ret_fast_syscall+0x0/0x3c)
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Erik Faye-Lund <kusmabite@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Adds some driver documentation for Tegra. It provides a short overview
of the hardware and software architectures.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Improve kerneldoc for the public parts of the host1x infrastructure in
preparation for adding driver-specific part to the GPU documentation.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently they return -1 on error, which will confuse callers if
they try to interpret it as a normal negative error code.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Since version 3.0.0 of the SMBIOS specification, there can be
multiple entry points in memory, pointing to one or two DMI tables.
If both a 32-bit ("_SM_") entry point and a 64-bit ("_SM3_") entry
point are present, the specification requires that the latter points
to a table which is a super-set of the table pointed to by the
former. Therefore we should give preference to the 64-bit ("_SM3_")
entry point.
However, currently the code is picking the first valid entry point
it finds. Per specification, we should look for a 64-bit ("_SM3_")
entry point first, and if we can't find any, look for a 32-bit
("_SM_" or "_DMI_") entry point. Modify the code to do that.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
The kernel watchdog is a great debugging tool for finding tasks that
consume a disproportionate amount of CPU time in contiguous chunks. One
can imagine building a similar watchdog for arbitrary driver threads
using save_stack_trace_tsk() and print_stack_trace(). However, this is
not viable for dynamically loaded driver modules on ARM platforms
because save_stack_trace_tsk() is not exported for those architectures.
Export save_stack_trace_tsk() for the ARM64 architecture to align with
x86 and support various debugging use cases such as arbitrary driver
thread watchdog timers.
Signed-off-by: Dustin Brown <dustinb@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
It's not hard to trigger a bunch of d_invalidate() on the same
dentry in parallel. They end up fighting each other - any
dentry picked for removal by one will be skipped by the rest
and we'll go for the next iteration through the entire
subtree, even if everything is being skipped. Morevoer, we
immediately go back to scanning the subtree. The only thing
we really need is to dissolve all mounts in the subtree and
as soon as we've nothing left to do, we can just unhash the
dentry and bugger off.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The Hi3660 SoC comes with the sp804 timer in addition to the
architecture timers. These ones are shutdown when reaching a deep idle
states and a backup timer is needed. The sp804 belongs to another power
domain and can fulfill the purpose of replacing temporarily an
architecture timer when the CPU is idle.
Describe it in the device tree, so it can be enabled at boot time.
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Add spi2 and spi3 device nodes for hi3660, and enable them for hikey960.
On HiKey960:
- SPI2 is wired out through low speed expansion connector.
- SPI3 is wired out through high speed expansion connector.
Signed-off-by: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
HiKey960 has four user LEDs, and two special purpose LEDs: WiFi and BT
respectively.
All of them are implemented as GPIO.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
We use gpio_034 as power key on hikey960, and set gpio with pull-up
state, when key press the voltage on the gpio will come to lower, and
power key event will be reported.
Signed-off-by: Chen Jun <chenjun14@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
This adds the serial slave device for the WL1837 Bluetooth interface.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Add nodes uart0 to uart4 and uart6 for hi3660 SoC.
Enable uart3 and uart6, disable uart5, in hikey960 board dts.
On HiKey960:
- UART6 is used as default console, and is wired out through low speed
expansion connector.
- UART3 has RTS/CTS hardware handshake, and is wired out through low
speed expansion connector.
- UART5 is not used in commercial launched boards. So disable it.
- UART4 is connected to Bluetooth, WL1837.
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Reviewed-by: Zhangfei Gao <zhangfei.gao@hisilicon.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Commit 316ca8804e ("ACPI/IORT: Remove linker section for IORT entries
probing") removed the linker section for IORT entries probing.
Since those IORT entries were the only iort_node_match() interface
users, the iort_node_match() became obsolete and can then be removed.
Remove the ACPI IORT iort_node_match() interface from the kernel.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ACPI IORT is an ACPI addendum to describe the connection topology of
devices with IOMMUs and interrupt controllers on ARM64 ACPI systems.
Currently the ACPI IORT Kbuild symbol is selected whenever the Kbuild
symbol ARM_GIC_V3_ITS is enabled, which in turn is selected by ARM64
Kbuild defaults. This makes the logic behind ACPI_IORT selection a bit
twisted and not easy to follow. On ARM64 systems enabling ACPI the
kbuild symbol ACPI_IORT should always be selected in that it is a kernel
layer provided to the ARM64 arch code to parse and enable ACPI firmware
bindings.
Make the ACPI_IORT selection explicit in ARM64 Kbuild and remove the
selection from ARM_GIC_V3_ITS entry, making the ACPI_IORT selection
logic clearer to follow.
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The current null-pointer check in __dma_alloc_coherent and
__dma_free_coherent is not needed anymore since the
__dma_alloc/__dma_free functions won't be called if !dev (dummy ops will
be called instead).
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Olav Haugan <ohaugan@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
All PMU drivers are going to depend on PERF_EVENTS, so let's make this
dependency common and simplify the individual Kconfig entries.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The .its targets require information about the kernel binary, such as
its entry point, which is extracted from the vmlinux ELF. We therefore
require that the ELF is built before the .its files are generated.
Declare this requirement in the Makefile such that make will ensure this
is always the case, otherwise in corner cases we can hit issues as the
.its is generated with an incorrect (either invalid or stale) entry
point.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: cf2a5e0bb4 ("MIPS: Support generating Flattened Image Trees (.itb)")
Cc: linux-mips@linux-mips.org
Cc: stable <stable@vger.kernel.org> # v4.9+
Patchwork: https://patchwork.linux-mips.org/patch/16179/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code handling the pop76 opcode (ie. bnezc & jialc instructions) in
__compute_return_epc_for_insn() needs to set the value of $31 in the
jialc case, which is encoded with rs = 0. However its check to
differentiate bnezc (rs != 0) from jialc (rs = 0) was unfortunately
backwards, meaning that if we emulate a bnezc instruction we clobber $31
& if we emulate a jialc instruction it actually behaves like a jic
instruction.
Fix this by inverting the check of rs to match the way the instructions
are actually encoded.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 28d6f93d20 ("MIPS: Emulate the new MIPS R6 BNEZC and JIALC instructions")
Cc: stable <stable@vger.kernel.org> # v4.0+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16178/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If this memory allocation fail, we must disable what has been enabled.
Do not return immediately but go thrue the error handling path instead.
Also use 'devm_kmemdup' instead of 'devm_kzalloc+memcpy' to simplify code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull networking fixes from David Miller:
1) The netlink attribute passed in to dev_set_alias() is not
necessarily NULL terminated, don't use strlcpy() on it. From
Alexander Potapenko.
2) Fix implementation of atomics in arm64 bpf JIT, from Daniel
Borkmann.
3) Correct the release of netdevs and driver private data in certain
circumstances.
4) Sanitize netlink message length properly in decnet, from Mateusz
Jurczyk.
5) Don't leak kernel data in rtnl_fill_vfinfo() netlink blobs. From
Yuval Mintz.
6) Hash secret is never initialized in ipv6 ILA translation code, from
Arnd Bergmann. I guess those clang warnings about unused inline
functions are useful for something!
7) Fix endian selection in bpf_endian.h, from Daniel Borkmann.
8) Sanitize sockaddr length before dereferncing any fields in AF_UNIX
and CAIF. From Mateusz Jurczyk.
9) Fix timestamping for GMAC3 chips in stmmac driver, from Mario
Molitor.
10) Do not leak netdev on dev_alloc_name() errors in mac80211, from
Johannes Berg.
11) Fix locking in sctp_for_each_endpoint(), from Xin Long.
12) Fix wrong memset size on 32-bit in snmp6, from Christian Perle.
13) Fix use after free in ip_mc_clear_src(), from WANG Cong.
14) Fix regressions caused by ICMP rate limiting changes in 4.11, from
Jesper Dangaard Brouer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (91 commits)
i40e: Fix a sleep-in-atomic bug
net: don't global ICMP rate limit packets originating from loopback
net/act_pedit: fix an error code
net: update undefined ->ndo_change_mtu() comment
net_sched: move tcf_lock down after gen_replace_estimator()
caif: Add sockaddr length check before accessing sa_family in connect handler
qed: fix dump of context data
qmi_wwan: new Telewell and Sierra device IDs
net: phy: Fix MDIO_THUNDER dependencies
netconsole: Remove duplicate "netconsole: " logging prefix
igmp: acquire pmc lock for ip_mc_clear_src()
r8152: give the device version
net: rps: fix uninitialized symbol warning
mac80211: don't send SMPS action frame in AP mode when not needed
mac80211/wpa: use constant time memory comparison for MACs
mac80211: set bss_info data before configuring the channel
mac80211: remove 5/10 MHz rate code from station MLME
mac80211: Fix incorrect condition when checking rx timestamp
mac80211: don't look at the PM bit of BAR frames
i40e: fix handling of HW ATR eviction
...
Pull crypto fix from Herbert Xu:
"This fixes a bug on sparc where we may dereference freed stack memory"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: Work around deallocated stack frame reference gcc bug on sparc.
