[ Upstream commit 0edd6b64d1 ]
Unless the very next line is schedule(), or implies it, one must not use
preempt_enable_no_resched(). It can cause a preemption to go missing and
thereby cause arbitrary delays, breaking the PREEMPT=y invariant.
Cc: Roman Gushchin <guro@fb.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 349ced9984 ]
Fix a similar endless event loop as was done in commit
8dcf32175b ("i2c: prevent endless uevent loop with
CONFIG_I2C_DEBUG_CORE"):
The culprit is the dev_dbg printk in the i2c uevent handler. If
this is activated (for instance by CONFIG_I2C_DEBUG_CORE) it results
in an endless loop with systemd-journald.
This happens if user-space scans the system log and reads the uevent
file to get information about a newly created device, which seems
fair use to me. Unfortunately reading the "uevent" file uses the
same function that runs for creating the uevent for a new device,
generating the next syslog entry
Both CONFIG_I2C_DEBUG_CORE and CONFIG_POWER_SUPPLY_DEBUG were reported
in https://bugs.freedesktop.org/show_bug.cgi?id=76886 but only former
seems to have been fixed. Drop debug prints as it was done in I2C
subsystem to resolve the issue.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 811328fc32 ]
A failed KVM_ARM_VCPU_INIT should not set the vcpu target,
as the vcpu target is used by kvm_vcpu_initialized() to
determine if other vcpu ioctls may proceed. We need to set
the target before calling kvm_reset_vcpu(), but if that call
fails, we should then unset it and clear the feature bitmap
while we're at it.
Signed-off-by: Andrew Jones <drjones@redhat.com>
[maz: Simplified patch, completed commit message]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22e8860cf8 ]
regmap_update_bits could fail and deserves a check.
The patch adds the checks and if it fails, returns its error
code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1267cf3c0 ]
The txq of vif is added to active_txqs list for ATF TXQ scheduling
in the function ieee80211_queue_skb(), but it was not properly removed
before freeing the txq object. It was causing use after free of the txq
objects from the active_txqs list, result was kernel panic
due to invalid memory access.
Fix kernel invalid memory access by properly removing txq object
from active_txqs list before free the object.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da66761c2d ]
It was reported that with some special Multi Processor Group configuration,
e.g:
bcdedit.exe /set groupsize 1
bcdedit.exe /set maxgroup on
bcdedit.exe /set groupaware on
for a 16-vCPU guest WS2012 shows BSOD on boot when PV TLB flush mechanism
is in use.
Tracing kvm_hv_flush_tlb immediately reveals the issue:
kvm_hv_flush_tlb: processor_mask 0x0 address_space 0x0 flags 0x2
The only flag set in this request is HV_FLUSH_ALL_VIRTUAL_ADDRESS_SPACES,
however, processor_mask is 0x0 and no HV_FLUSH_ALL_PROCESSORS is specified.
We don't flush anything and apparently it's not what Windows expects.
TLFS doesn't say anything about such requests and newer Windows versions
seem to be unaffected. This all feels like a WS2012 bug, which is, however,
easy to workaround in KVM: let's flush everything when we see an empty
flush request, over-flushing doesn't hurt.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5bc73f34c ]
In most cases, kmalloc() will not be available early in boot when
pci_setup() is called. Thus, the kstrdup() call that was added to fix the
__initdata bug with the disable_acs_redir parameter usually returns NULL,
so the parameter is discarded and has no effect.
To fix this, store the string that's in initdata until an initcall function
can allocate the memory appropriately. This way we don't need any
additional static memory.
Fixes: d2fd6e8191 ("PCI: Fix __initdata issue with "pci=disable_acs_redir" parameter")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f51dcd0f62 ]
symlink body shouldn't be freed without an RCU delay. Switch apparmorfs
to ->destroy_inode() and use of call_rcu(); free both the inode and symlink
body in the callback.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46c8744196 ]
symlink body shouldn't be freed without an RCU delay. Switch securityfs
to ->destroy_inode() and use of call_rcu(); free both the inode and symlink
body in the callback.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbe7208c6c ]
If called fast enough so samples do not increment, we can get
division by zero in kernel:
__div0
cpcap_battery_cc_raw_div
cpcap_battery_get_property
power_supply_get_property.part.1
power_supply_get_property
power_supply_show_property
power_supply_uevent
Fixes: 874b2adbed ("power: supply: cpcap-battery: Add a battery driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2abc330c51 ]
Sometimes one of the nkmp factors is unused. This means that one of the
factors shift and width values are set to 0. Current nkmp clock code
generates a mask for each factor with GENMASK(width + shift - 1, shift).
For unused factor this translates to GENMASK(-1, 0). This code is
further expanded by C preprocessor to final version:
(((~0UL) - (1UL << (0)) + 1) & (~0UL >> (BITS_PER_LONG - 1 - (-1))))
or a bit simplified:
(~0UL & (~0UL >> BITS_PER_LONG))
It turns out that result of the second part (~0UL >> BITS_PER_LONG) is
actually undefined by C standard, which clearly specifies:
"If the value of the right operand is negative or is greater than or
equal to the width of the promoted left operand, the behavior is
undefined."
Additionally, compiling kernel with aarch64-linux-gnu-gcc 8.3.0 gave
different results whether literals or variables with same values as
literals were used. GENMASK with literals -1 and 0 gives zero and with
variables gives 0xFFFFFFFFFFFFFFF (~0UL). Because nkmp driver uses
GENMASK with variables as parameter, expression calculates mask as ~0UL
instead of 0. This has further consequences that LSB in register is
always set to 1 (1 is neutral value for a factor and shift is 0).
For example, H6 pll-de clock is set to 600 MHz by sun4i-drm driver, but
due to this bug ends up being 300 MHz. Additionally, 300 MHz seems to be
too low because following warning can be found in dmesg:
[ 1.752763] WARNING: CPU: 2 PID: 41 at drivers/clk/sunxi-ng/ccu_common.c:41 ccu_helper_wait_for_lock.part.0+0x6c/0x90
[ 1.763378] Modules linked in:
[ 1.766441] CPU: 2 PID: 41 Comm: kworker/2:1 Not tainted 5.1.0-rc2-next-20190401 #138
[ 1.774269] Hardware name: Pine H64 (DT)
[ 1.778200] Workqueue: events deferred_probe_work_func
[ 1.783341] pstate: 40000005 (nZcv daif -PAN -UAO)
[ 1.788135] pc : ccu_helper_wait_for_lock.part.0+0x6c/0x90
[ 1.793623] lr : ccu_helper_wait_for_lock.part.0+0x48/0x90
[ 1.799107] sp : ffff000010f93840
[ 1.802422] x29: ffff000010f93840 x28: 0000000000000000
[ 1.807735] x27: ffff800073ce9d80 x26: ffff000010afd1b8
[ 1.813049] x25: ffffffffffffffff x24: 00000000ffffffff
[ 1.818362] x23: 0000000000000001 x22: ffff000010abd5c8
[ 1.823675] x21: 0000000010000000 x20: 00000000685f367e
[ 1.828987] x19: 0000000000001801 x18: 0000000000000001
[ 1.834300] x17: 0000000000000001 x16: 0000000000000000
[ 1.839613] x15: 0000000000000000 x14: ffff000010789858
[ 1.844926] x13: 0000000000000000 x12: 0000000000000001
[ 1.850239] x11: 0000000000000000 x10: 0000000000000970
[ 1.855551] x9 : ffff000010f936c0 x8 : ffff800074cec0d0
[ 1.860864] x7 : 0000800067117000 x6 : 0000000115c30b41
[ 1.866177] x5 : 00ffffffffffffff x4 : 002c959300bfe500
[ 1.871490] x3 : 0000000000000018 x2 : 0000000029aaaaab
[ 1.876802] x1 : 00000000000002e6 x0 : 00000000686072bc
[ 1.882114] Call trace:
[ 1.884565] ccu_helper_wait_for_lock.part.0+0x6c/0x90
[ 1.889705] ccu_helper_wait_for_lock+0x10/0x20
[ 1.894236] ccu_nkmp_set_rate+0x244/0x2a8
[ 1.898334] clk_change_rate+0x144/0x290
[ 1.902258] clk_core_set_rate_nolock+0x180/0x1b8
[ 1.906963] clk_set_rate+0x34/0xa0
[ 1.910455] sun8i_mixer_bind+0x484/0x558
[ 1.914466] component_bind_all+0x10c/0x230
[ 1.918651] sun4i_drv_bind+0xc4/0x1a0
[ 1.922401] try_to_bring_up_master+0x164/0x1c0
[ 1.926932] __component_add+0xa0/0x168
[ 1.930769] component_add+0x10/0x18
[ 1.934346] sun8i_dw_hdmi_probe+0x18/0x20
[ 1.938443] platform_drv_probe+0x50/0xa0
[ 1.942455] really_probe+0xcc/0x280
[ 1.946032] driver_probe_device+0x54/0xe8
[ 1.950130] __device_attach_driver+0x80/0xb8
[ 1.954488] bus_for_each_drv+0x78/0xc8
[ 1.958326] __device_attach+0xd4/0x130
[ 1.962163] device_initial_probe+0x10/0x18
[ 1.966348] bus_probe_device+0x90/0x98
[ 1.970185] deferred_probe_work_func+0x6c/0xa0
[ 1.974720] process_one_work+0x1e0/0x320
[ 1.978732] worker_thread+0x228/0x428
[ 1.982484] kthread+0x120/0x128
[ 1.985714] ret_from_fork+0x10/0x18
[ 1.989290] ---[ end trace 9babd42e1ca4b84f ]---
This commit solves the issue by first checking value of the factor
width. If it is equal to 0 (unused factor), mask is set to 0, otherwise
GENMASK() macro is used as before.
Fixes: d897ef56fa ("clk: sunxi-ng: Mask nkmp factors when setting register")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8742dc86d0 ]
We currently don't reload pointers pointing into skb header
after doing pskb_may_pull() in _decode_session4(). So in case
pskb_may_pull() changed the pointers, we read from random
memory. Fix this by putting all the needed infos on the
stack, so that we don't need to access the header pointers
after doing pskb_may_pull().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 025c65e119 ]
If an xfrmi is associated to a vrf layer 3 master device,
xfrm_policy_check() fails after traffic decapsulation. The input
interface is replaced by the layer 3 master device, and hence
xfrmi_decode_session() can't match the xfrmi anymore to satisfy
policy checking.
Extend ingress xfrmi lookup to honor the original layer 3 slave
device, allowing xfrm interfaces to operate within a vrf domain.
Fixes: f203b76d78 ("xfrm: Add virtual xfrm interfaces")
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8dfb4eba41 ]
esp_output_udp_encap can produce a length that doesn't fit in the 16
bits of a UDP header's length field. In that case, we'll send a
fragmented packet whose length is larger than IP_MAX_MTU (resulting in
"Oversized IP packet" warnings on receive) and with a bogus UDP
length.
To prevent this, add a length check to esp_output_udp_encap and return
-EMSGSIZE on failure.
This seems to be older than git history.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbb2483b2a ]
In commit 6a53b75932 ("xfrm: check id proto in validate_tmpl()")
I introduced a check for xfrm protocol, but according to Herbert
IPSEC_PROTO_ANY should only be used as a wildcard for lookup, so
it should be removed from validate_tmpl().
And, IPSEC_PROTO_ANY is expected to only match 3 IPSec-specific
protocols, this is why xfrm_state_flush() could still miss
IPPROTO_ROUTING, which leads that those entries are left in
net->xfrm.state_all before exit net. Fix this by replacing
IPSEC_PROTO_ANY with zero.
This patch also extracts the check from validate_tmpl() to
xfrm_id_proto_valid() and uses it in parse_ipsecrequest().
With this, no other protocols should be added into xfrm.
Fixes: 6a53b75932 ("xfrm: check id proto in validate_tmpl()")
Reported-by: syzbot+0bf0519d6e0de15914fe@syzkaller.appspotmail.com
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5483844c3f ]
If tunnel registration failed during module initialization, the module
would fail to deregister the IPPROTO_COMP protocol and would attempt to
deregister the tunnel.
The tunnel was not deregistered during module-exit.
Fixes: dd9ee34440 ("vti4: Fix a ipip packet processing bug in 'IPCOMP' virtual tunnel")
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ee02a54ef ]
When unloading xfrm6_tunnel module, xfrm6_tunnel_fini directly
frees the xfrm6_tunnel_spi_kmem. Maybe someone has gotten the
xfrm6_tunnel_spi, so need to wait it.
Fixes: 91cc3bb0b04ff("xfrm6_tunnel: RCU conversion")
Signed-off-by: Su Yanjun <suyj.fnst@cn.fujitsu.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b805d78d30 ]
UBSAN report this:
UBSAN: Undefined behaviour in net/xfrm/xfrm_policy.c:1289:24
index 6 is out of range for type 'unsigned int [6]'
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.4.162-514.55.6.9.x86_64+ #13
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
0000000000000000 1466cf39b41b23c9 ffff8801f6b07a58 ffffffff81cb35f4
0000000041b58ab3 ffffffff83230f9c ffffffff81cb34e0 ffff8801f6b07a80
ffff8801f6b07a20 1466cf39b41b23c9 ffffffff851706e0 ffff8801f6b07ae8
Call Trace:
<IRQ> [<ffffffff81cb35f4>] __dump_stack lib/dump_stack.c:15 [inline]
<IRQ> [<ffffffff81cb35f4>] dump_stack+0x114/0x1a0 lib/dump_stack.c:51
[<ffffffff81d94225>] ubsan_epilogue+0x12/0x8f lib/ubsan.c:164
[<ffffffff81d954db>] __ubsan_handle_out_of_bounds+0x16e/0x1b2 lib/ubsan.c:382
[<ffffffff82a25acd>] __xfrm_policy_unlink+0x3dd/0x5b0 net/xfrm/xfrm_policy.c:1289
[<ffffffff82a2e572>] xfrm_policy_delete+0x52/0xb0 net/xfrm/xfrm_policy.c:1309
[<ffffffff82a3319b>] xfrm_policy_timer+0x30b/0x590 net/xfrm/xfrm_policy.c:243
[<ffffffff813d3927>] call_timer_fn+0x237/0x990 kernel/time/timer.c:1144
[<ffffffff813d8e7e>] __run_timers kernel/time/timer.c:1218 [inline]
[<ffffffff813d8e7e>] run_timer_softirq+0x6ce/0xb80 kernel/time/timer.c:1401
[<ffffffff8120d6f9>] __do_softirq+0x299/0xe10 kernel/softirq.c:273
[<ffffffff8120e676>] invoke_softirq kernel/softirq.c:350 [inline]
[<ffffffff8120e676>] irq_exit+0x216/0x2c0 kernel/softirq.c:391
[<ffffffff82c5edab>] exiting_irq arch/x86/include/asm/apic.h:652 [inline]
[<ffffffff82c5edab>] smp_apic_timer_interrupt+0x8b/0xc0 arch/x86/kernel/apic/apic.c:926
[<ffffffff82c5c985>] apic_timer_interrupt+0xa5/0xb0 arch/x86/entry/entry_64.S:735
<EOI> [<ffffffff81188096>] ? native_safe_halt+0x6/0x10 arch/x86/include/asm/irqflags.h:52
[<ffffffff810834d7>] arch_safe_halt arch/x86/include/asm/paravirt.h:111 [inline]
[<ffffffff810834d7>] default_idle+0x27/0x430 arch/x86/kernel/process.c:446
[<ffffffff81085f05>] arch_cpu_idle+0x15/0x20 arch/x86/kernel/process.c:437
[<ffffffff8132abc3>] default_idle_call+0x53/0x90 kernel/sched/idle.c:92
[<ffffffff8132b32d>] cpuidle_idle_call kernel/sched/idle.c:156 [inline]
[<ffffffff8132b32d>] cpu_idle_loop kernel/sched/idle.c:251 [inline]
[<ffffffff8132b32d>] cpu_startup_entry+0x60d/0x9a0 kernel/sched/idle.c:299
[<ffffffff8113e119>] start_secondary+0x3c9/0x560 arch/x86/kernel/smpboot.c:245
The issue is triggered as this:
xfrm_add_policy
-->verify_newpolicy_info //check the index provided by user with XFRM_POLICY_MAX
//In my case, the index is 0x6E6BB6, so it pass the check.
-->xfrm_policy_construct //copy the user's policy and set xfrm_policy_timer
-->xfrm_policy_insert
--> __xfrm_policy_link //use the orgin dir, in my case is 2
--> xfrm_gen_index //generate policy index, there is 0x6E6BB6
then xfrm_policy_timer be fired
xfrm_policy_timer
--> xfrm_policy_id2dir //get dir from (policy index & 7), in my case is 6
--> xfrm_policy_delete
--> __xfrm_policy_unlink //access policy_count[dir], trigger out of range access
Add xfrm_policy_id2dir check in verify_newpolicy_info, make sure the computed dir is
valid, to fix the issue.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e682adf021 ("xfrm: Try to honor policy index if it's supplied by user")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bbd84f3365 upstream.
Starting from commit 9c225f2655 ("vfs: atomic f_pos accesses as per
POSIX") files opened even via nonseekable_open gate read and write via lock
and do not allow them to be run simultaneously. This can create read vs
write deadlock if a filesystem is trying to implement a socket-like file
which is intended to be simultaneously used for both read and write from
filesystem client. See commit 10dce8af34 ("fs: stream_open - opener for
stream-like files so that read and write can run simultaneously without
deadlock") for details and e.g. commit 581d21a2d0 ("xenbus: fix deadlock
on writes to /proc/xen/xenbus") for a similar deadlock example on
/proc/xen/xenbus.
To avoid such deadlock it was tempting to adjust fuse_finish_open to use
stream_open instead of nonseekable_open on just FOPEN_NONSEEKABLE flags,
but grepping through Debian codesearch shows users of FOPEN_NONSEEKABLE,
and in particular GVFS which actually uses offset in its read and write
handlers
https://codesearch.debian.net/search?q=-%3Enonseekable+%3Dhttps://gitlab.gnome.org/GNOME/gvfs/blob/1.40.0-6-gcbc54396/client/gvfsfusedaemon.c#L1080https://gitlab.gnome.org/GNOME/gvfs/blob/1.40.0-6-gcbc54396/client/gvfsfusedaemon.c#L1247-1346https://gitlab.gnome.org/GNOME/gvfs/blob/1.40.0-6-gcbc54396/client/gvfsfusedaemon.c#L1399-1481
so if we would do such a change it will break a real user.
Add another flag (FOPEN_STREAM) for filesystem servers to indicate that the
opened handler is having stream-like semantics; does not use file position
and thus the kernel is free to issue simultaneous read and write request on
opened file handle.
This patch together with stream_open() should be added to stable kernels
starting from v3.14+. This will allow to patch OSSPD and other FUSE
filesystems that provide stream-like files to return FOPEN_STREAM |
FOPEN_NONSEEKABLE in open handler and this way avoid the deadlock on all
kernel versions. This should work because fuse_finish_open ignores unknown
open flags returned from a filesystem and so passing FOPEN_STREAM to a
kernel that is not aware of this flag cannot hurt. In turn the kernel that
is not aware of FOPEN_STREAM will be < v3.14 where just FOPEN_NONSEEKABLE
is sufficient to implement streams without read vs write deadlock.
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: Kirill Smelkov <kirr@nexedi.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 940bc47178 upstream.
Commit b592211c33 ("dm mpath: fix attached_handler_name leak and
dangling hw_handler_name pointer") fixed a memory leak for the case
where setup_scsi_dh() returns failure. But setup_scsi_dh may return
success and not "use" attached_handler_name if the
retain_attached_hwhandler flag is not set on the map. As setup_scsi_sh
properly "steals" the pointer by nullifying it, freeing it
unconditionally in parse_path() is safe.
Fixes: b592211c33 ("dm mpath: fix attached_handler_name leak and dangling hw_handler_name pointer")
Cc: stable@vger.kernel.org
Reported-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30bba430dd upstream.
When we use separate devices for data and metadata, dm-integrity would
incorrectly calculate the size of the metadata device as if it had
512-byte block size - and it would refuse activation with larger block
size and smaller metadata device.
Fix this so that it takes actual block size into account, which fixes
the following reported issue:
https://gitlab.com/cryptsetup/cryptsetup/issues/450
Fixes: 356d9d52e1 ("dm integrity: allow separate metadata device")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81bc6d150a upstream.
When the target line contains an invalid device, delay_ctr() will call
delay_dtr() with NULL workqueue. Attempting to destroy the NULL
workqueue causes a crash.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7aedf75ff7 upstream.
The function blkdev_report_zones() returns success even if no zone
information is reported (empty report). Empty zone reports can only
happen if the report start sector passed exceeds the device capacity.
The conditions for this to happen are either a bug in the caller code,
or, a change in the device that forced the low level driver to change
the device capacity to a value that is lower than the report start
sector. This situation includes a failed disk revalidation resulting in
the disk capacity being changed to 0.
If this change happens while dm-zoned is in its initialization phase
executing dmz_init_zones(), this function may enter an infinite loop
and hang the system. To avoid this, add a check to disallow empty zone
reports and bail out early. Also fix the function dmz_update_zone() to
make sure that the report for the requested zone was correctly obtained.
Fixes: 3b1a94c88b ("dm zoned: drive-managed zoned block device target")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Shaun Tancheff <shaun@tancheff.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e28adc3bf3 upstream.
Add missing dm_bitset_cursor_next() to properly advance the bitset
cursor.
Otherwise, the discarded state of all blocks is set according to the
discarded state of the first block.
Fixes: ae4a46a1f6 ("dm cache metadata: use bitset cursor api to load discard bitset")
Cc: stable@vger.kernel.org
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ec73791a6 upstream.
Due to an erratum in some Pericom PCIe-to-PCI bridges in reverse mode
(conventional PCI on primary side, PCIe on downstream side), the Retrain
Link bit needs to be cleared manually to allow the link training to
complete successfully.
If it is not cleared manually, the link training is continuously restarted
and no devices below the PCI-to-PCIe bridge can be accessed. That means
drivers for devices below the bridge will be loaded but won't work and may
even crash because the driver is only reading 0xffff.
See the Pericom Errata Sheet PI7C9X111SLB_errata_rev1.2_102711.pdf for
details. Devices known as affected so far are: PI7C9X110, PI7C9X111SL,
PI7C9X130.
Add a new flag, clear_retrain_link, in struct pci_dev. Quirks for affected
devices set this bit.
Note that pcie_retrain_link() lives in aspm.c because that's currently the
only place we use it, but this erratum is not specific to ASPM, and we may
retrain links for other reasons in the future.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
[bhelgaas: apply regardless of CONFIG_PCIEASPM]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be20bbcb0a upstream.
Reestablish the PCIe link very early in the resume process in case it
went down to prevent PCI accesses from hanging the bus. Such accesses
can happen early in the PCI resume process, as early as the
SUSPEND_RESUME_NOIRQ step, thus the link must be reestablished in the
driver resume_noirq() callback.
Fixes: e015f88c36 ("PCI: rcar: Add support for R-Car H3 to pcie-rcar")
Signed-off-by: Kazufumi Ikeda <kaz-ikeda@xc.jp.nec.com>
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
[lorenzo.pieralisi@arm.com: reformatted commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@vger.kernel.org
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6302bf3ef7 upstream.
Two functions allocate a host bridge: devm_pci_alloc_host_bridge() and
pci_alloc_host_bridge(). At the moment, only the unmanaged one initializes
the PCIe feature bits, which prevents from using features such as hotplug
or AER on some systems, when booting with device tree. Make the
initialization code common.
Fixes: 02bfeb4842 ("PCI/portdrv: Simplify PCIe feature permission checking")
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.17+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f627caf55b upstream.
On a Thinkpad s30 (Pentium III / i440MX, Lynx3DM), blanking the display
or starting the X server will crash and freeze the system, or garble the
display.
Experiments showed this problem can mostly be solved by adjusting the
order of register writes. Also, sm712fb failed to consider the difference
of clock frequency when unblanking the display, and programs the clock for
SM712 to SM720.
Fix them by adjusting the order of register writes, and adding an
additional check for SM720 for programming the clock frequency.
Signed-off-by: Yifeng Li <tomli@tomli.me>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Teddy Wang <teddy.wang@siliconmotion.com>
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ed7d2ccb7 upstream.
Loongson MIPS netbooks use 1024x600 LCD panels, which is the original
target platform of this driver, but nearly all old x86 laptops have
1024x768. Lighting 768 panels using 600's timings would partially
garble the display. Since it's not possible to distinguish them reliably,
we change the default to 768, but keep 600 as-is on MIPS.
Further, earlier laptops, such as IBM Thinkpad 240X, has a 800x600 LCD
panel, this driver would probably garbled those display. As we don't
have one for testing, the original behavior of the driver is kept as-is,
but the problem has been documented is the comments.
Signed-off-by: Yifeng Li <tomli@tomli.me>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Teddy Wang <teddy.wang@siliconmotion.com>
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6053d3a479 upstream.
In order to support the 1024x600 panel on Yeeloong Loongson MIPS
laptop, the original 1024x768-16 table was modified to 1024x600-16,
without leaving the original. It causes problem on x86 laptop as
the 1024x768-16 support was still claimed but not working.
Fix it by introducing the 1024x768-16 mode.
Signed-off-by: Yifeng Li <tomli@tomli.me>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Teddy Wang <teddy.wang@siliconmotion.com>
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e0e59993d upstream.
On a Thinkpad s30 (Pentium III / i440MX, Lynx3DM), running fbtest or X
will crash the machine instantly, because the VRAM/framebuffer is not
mapped correctly.
On SM712, the framebuffer starts at the beginning of address space, but
SM720's framebuffer starts at the 1 MiB offset from the beginning. However,
sm712fb fails to take this into account, as a result, writing to the
framebuffer will destroy all the registers and kill the system immediately.
Another problem is the driver assumes 8 MiB of VRAM for SM720, but some
SM720 system, such as this IBM Thinkpad, only has 4 MiB of VRAM.
Fix this problem by removing the hardcoded VRAM size, adding a function to
query the amount of VRAM from register MCR76 on SM720, and adding proper
framebuffer offset.
Please note that the memory map may have additional problems on Big-Endian
system, which is not available for testing by myself. But I highly suspect
that the original code is also broken on Big-Endian machines for SM720, so
at least we are not making the problem worse. More, the driver also assumed
SM710/SM712 has 4 MiB of VRAM, but it has a 2 MiB version as well, and used
in earlier laptops, such as IBM Thinkpad 240X, the driver would probably
crash on them. I've never seen one of those machines and cannot fix it, but
I have documented these problems in the comments.
Signed-off-by: Yifeng Li <tomli@tomli.me>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Teddy Wang <teddy.wang@siliconmotion.com>
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec1587d507 upstream.
When the machine is booted in VGA mode, loading sm712fb would cause
a glitch of random pixels shown on the screen. To prevent it from
happening, we first clear the entire framebuffer, and we also need
to stop calling smtcfb_setmode() during initialization, the fbdev
layer will call it for us later when it's ready.
Signed-off-by: Yifeng Li <tomli@tomli.me>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Teddy Wang <teddy.wang@siliconmotion.com>
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8069053880 upstream.
On a Thinkpad s30 (Pentium III / i440MX, Lynx3DM), rebooting with
sm712fb framebuffer driver would cause a white screen of death on
the next POST, presumably the proper timings for the LCD panel was
not reprogrammed properly by the BIOS.
Experiments showed a few CRTC Scratch Registers, including CRT3D,
CRT3E and CRT3F may be used internally by BIOS as some flags. CRT3B is
a hardware testing register, we shouldn't mess with it. CRT3C has
blanking signal and line compare control, which is not needed for this
driver.
Stop writing to CR3B-CR3F (a.k.a CRT3B-CRT3F) registers. Even if these
registers don't have side-effect on other systems, writing to them is
also highly questionable.
Signed-off-by: Yifeng Li <tomli@tomli.me>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Teddy Wang <teddy.wang@siliconmotion.com>
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcf9070595 upstream.
On a Thinkpad s30 (Pentium III / i440MX, Lynx3DM), the amount of Video
RAM is not detected correctly by the xf86-video-siliconmotion driver.
This is because sm712fb overwrites the GPR71 Scratch Pad Register, which
is set by BIOS on x86 and used to indicate amount of VRAM.
Other Scratch Pad Registers, including GPR70/74/75, don't have the same
side-effect, but overwriting to them is still questionable, as they are
not related to modesetting.
Stop writing to SR70/71/74/75 (a.k.a GPR70/71/74/75).
Signed-off-by: Yifeng Li <tomli@tomli.me>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Teddy Wang <teddy.wang@siliconmotion.com>
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5481115e25 upstream.
On a Thinkpad s30 (Pentium III / i440MX, Lynx3DM), rebooting with
sm712fb framebuffer driver would cause the role of brightness up/down
button to swap.
Experiments showed the FPR30 register caused this behavior. Moreover,
even if this register don't have side-effect on other systems, over-
writing it is also highly questionable, since it was originally
configurated by the motherboard manufacturer by hardwiring pull-down
resistors to indicate the type of LCD panel. We should not mess with
it.
Stop writing to the SR30 (a.k.a FPR30) register.
Signed-off-by: Yifeng Li <tomli@tomli.me>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Teddy Wang <teddy.wang@siliconmotion.com>
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8585539df upstream.
The following commit:
38ac0287b7 ("fbdev/efifb: Honour UEFI memory map attributes when mapping the FB")
updated the EFI framebuffer code to use memory mappings for the linear
framebuffer that are permitted by the memory attributes described by the
EFI memory map for the particular region, if the framebuffer happens to
be covered by the EFI memory map (which is typically only the case for
framebuffers in shared memory). This is required since non-x86 systems
may require cacheable attributes for memory mappings that are shared
with other masters (such as GPUs), and this information cannot be
described by the Graphics Output Protocol (GOP) EFI protocol itself,
and so we rely on the EFI memory map for this.
As reported by James, this breaks some x86 systems:
[ 1.173368] efifb: probing for efifb
[ 1.173386] efifb: abort, cannot remap video memory 0x1d5000 @ 0xcf800000
[ 1.173395] Trying to free nonexistent resource <00000000cf800000-00000000cf9d4bff>
[ 1.173413] efi-framebuffer: probe of efi-framebuffer.0 failed with error -5
The problem turns out to be that the memory map entry that describes the
framebuffer has no memory attributes listed at all, and so we end up with
a mem_flags value of 0x0.
So work around this by ensuring that the memory map entry's attribute field
has a sane value before using it to mask the set of usable attributes.
Reported-by: James Hilliard <james.hilliard1@gmail.com>
Tested-by: James Hilliard <james.hilliard1@gmail.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org> # v4.19+
Cc: Borislav Petkov <bp@alien8.de>
Cc: James Morse <james.morse@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 38ac0287b7 ("fbdev/efifb: Honour UEFI memory map attributes when ...")
Link: http://lkml.kernel.org/r/20190516213159.3530-2-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b6599a9d8 upstream.
The sample timestamp is updated to ensure that the timestamp represents
the time of the sample and not a branch that the decoder is still
walking towards. The sample timestamp is updated when the decoder
returns, but the decoder does not return for non-taken branches. Update
the sample timestamp then also.
Note that commit 3f04d98e97 ("perf intel-pt: Improve sample
timestamp") was also a stable fix and appears, for example, in v4.4
stable tree as commit a4ebb58fd1 ("perf intel-pt: Improve sample
timestamp").
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org # v4.4+
Fixes: 3f04d98e97 ("perf intel-pt: Improve sample timestamp")
Link: http://lkml.kernel.org/r/20190510124143.27054-4-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61b6e08dc8 upstream.
The decoder uses its current timestamp in samples. Usually that is a
timestamp that has already passed, but in some cases it is a timestamp
for a branch that the decoder is walking towards, and consequently
hasn't reached.
The intel_pt_sample_time() function decides which is which, but was not
handling TNT packets exactly correctly.
In the case of TNT, the timestamp applies to the first branch, so the
decoder must first walk to that branch.
That means intel_pt_sample_time() should return true for TNT, and this
patch makes that change. However, if the first branch is a non-taken
branch (i.e. a 'N'), then intel_pt_sample_time() needs to return false
for subsequent taken branches in the same TNT packet.
To handle that, introduce a new state INTEL_PT_STATE_TNT_CONT to
distinguish the cases.
Note that commit 3f04d98e97 ("perf intel-pt: Improve sample
timestamp") was also a stable fix and appears, for example, in v4.4
stable tree as commit a4ebb58fd1 ("perf intel-pt: Improve sample
timestamp").
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org # v4.4+
Fixes: 3f04d98e97 ("perf intel-pt: Improve sample timestamp")
Link: http://lkml.kernel.org/r/20190510124143.27054-3-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ba8fa20e2 upstream.
The timestamp used to determine if an instruction sample is made, is an
estimate based on the number of instructions since the last known
timestamp. A consequence is that it might go backwards, which results in
extra samples. Change it so that a sample is only made when the
timestamp goes forwards.
Note this does not affect a sampling period of 0 or sampling periods
specified as a count of instructions.
Example:
Before:
$ perf script --itrace=i10us
ls 13812 [003] 2167315.222583: 3270 instructions:u: 7fac71e2e494 __GI___tunables_init+0xf4 (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 30902 instructions:u: 7fac71e2da0f _dl_cache_libcmp+0x2f (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 10 instructions:u: 7fac71e2d9ff _dl_cache_libcmp+0x1f (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 8 instructions:u: 7fac71e2d9ea _dl_cache_libcmp+0xa (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 14 instructions:u: 7fac71e2d9ea _dl_cache_libcmp+0xa (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 6 instructions:u: 7fac71e2d9ff _dl_cache_libcmp+0x1f (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 14 instructions:u: 7fac71e2d9ff _dl_cache_libcmp+0x1f (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 4 instructions:u: 7fac71e2dab2 _dl_cache_libcmp+0xd2 (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222728: 16423 instructions:u: 7fac71e2477a _dl_map_object_deps+0x1ba (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222734: 12731 instructions:u: 7fac71e27938 _dl_name_match_p+0x68 (/lib/x86_64-linux-gnu/ld-2.28.so)
...
After:
$ perf script --itrace=i10us
ls 13812 [003] 2167315.222583: 3270 instructions:u: 7fac71e2e494 __GI___tunables_init+0xf4 (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 30902 instructions:u: 7fac71e2da0f _dl_cache_libcmp+0x2f (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222728: 16479 instructions:u: 7fac71e2477a _dl_map_object_deps+0x1ba (/lib/x86_64-linux-gnu/ld-2.28.so)
...
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org
Fixes: f4aa081949 ("perf tools: Add Intel PT decoder")
Link: http://lkml.kernel.org/r/20190510124143.27054-2-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b906c056b6 upstream.
Multiplying the Memory Controller clock rate by the tick count results
in an integer overflow and in result the truncated tick value is being
programmed into hardware, such that the GR3D memory client performance is
reduced by two times.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbe08bcbbe upstream.
When reading only part of the id file, the ppos isn't tracked correctly.
This is taken care by simple_read_from_buffer.
Reading a single byte, and then the next byte would result EOF.
While this seems like not a big deal, this breaks abstractions that
reads information from files unbuffered. See for example
https://github.com/golang/go/issues/29399
This code was mentioned as problematic in
commit cd458ba9d5
("tracing: Do not (ab)use trace_seq in event_id_read()")
An example C code that show this bug is:
#include <stdio.h>
#include <stdint.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <unistd.h>
int main(int argc, char **argv) {
if (argc < 2)
return 1;
int fd = open(argv[1], O_RDONLY);
char c;
read(fd, &c, 1);
printf("First %c\n", c);
read(fd, &c, 1);
printf("Second %c\n", c);
}
Then run with, e.g.
sudo ./a.out /sys/kernel/debug/tracing/events/tcp/tcp_set_state/id
You'll notice you're getting the first character twice, instead of the
first two characters in the id file.
Link: http://lkml.kernel.org/r/20181231115837.4932-1-elazar@lightbitslabs.com
Cc: Orit Wasserman <orit.was@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 23725aeeab ("ftrace: provide an id file for each event")
Signed-off-by: Elazar Leibovich <elazar@lightbitslabs.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
