Broadcom 4377 controllers found in Apple x86 Macs with the T2 chip
claim to support extended scanning when querying supported states,
< HCI Command: LE Read Supported St.. (0x08|0x001c) plen 0
> HCI Event: Command Complete (0x0e) plen 12
LE Read Supported States (0x08|0x001c) ncmd 1
Status: Success (0x00)
States: 0x000003ffffffffff
[...]
LE Set Extended Scan Parameters (Octet 37 - Bit 5)
LE Set Extended Scan Enable (Octet 37 - Bit 6)
[...]
, but then fail to actually implement the extended scanning:
< HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8
Own address type: Random (0x01)
Filter policy: Accept all advertisement (0x00)
PHYs: 0x01
Entry 0: LE 1M
Type: Active (0x01)
Interval: 11.250 msec (0x0012)
Window: 11.250 msec (0x0012)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
Status: Unknown HCI Command (0x01)
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Broadcom controllers present on Apple Silicon devices use the upper
8 bits of the event type in the LE Extended Advertising Report for
the channel on which the frame has been received.
These bits are reserved according to the Bluetooth spec anyway such that
we can just drop them to ensure that the advertising results are parsed
correctly.
The following excerpt from a btmon trace shows a report received on
channel 37 by these controllers:
> HCI Event: LE Meta Event (0x3e) plen 55
LE Extended Advertising Report (0x0d)
Num reports: 1
Entry 0
Event type: 0x2513
Props: 0x0013
Connectable
Scannable
Use legacy advertising PDUs
Data status: Complete
Reserved (0x2500)
Legacy PDU Type: Reserved (0x2513)
Address type: Public (0x00)
Address: XX:XX:XX:XX:XX:XX (Shenzhen Jingxun Software [...])
Primary PHY: LE 1M
Secondary PHY: No packets
SID: no ADI field (0xff)
TX power: 127 dBm
RSSI: -76 dBm (0xb4)
Periodic advertising interval: 0.00 msec (0x0000)
Direct address type: Public (0x00)
Direct address: 00:00:00:00:00:00 (OUI 00-00-00)
Data length: 0x1d
[...]
Flags: 0x18
Simultaneous LE and BR/EDR (Controller)
Simultaneous LE and BR/EDR (Host)
Company: Harman International Industries, Inc. (87)
Data: [...]
Service Data (UUID 0xfddf):
Name (complete): JBL Flip 5
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The current version of the configuration structure has unaligned
16-bit fields, but according to the specification [1], access to
the configuration space must be aligned.
Add a second, aligned version of the configuration structure
and a new feature bit indicating that this version is being used.
[1] https://docs.oasis-open.org/virtio/virtio/v1.1/virtio-v1.1.pdf
Signed-off-by: Igor Skalkin <Igor.Skalkin@opensynergy.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On cmd_timeout with no reset_gpio, reset the USB port as a last
resort.
This patch changes the behavior of btusb_intel_cmd_timeout and
btusb_rtl_cmd_timeout.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@google.com>
Reviewed-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2022-12-11
We've added 74 non-merge commits during the last 11 day(s) which contain
a total of 88 files changed, 3362 insertions(+), 789 deletions(-).
The main changes are:
1) Decouple prune and jump points handling in the verifier, from Andrii.
2) Do not rely on ALLOW_ERROR_INJECTION for fmod_ret, from Benjamin.
Merged from hid tree.
3) Do not zero-extend kfunc return values. Necessary fix for 32-bit archs,
from Björn.
4) Don't use rcu_users to refcount in task kfuncs, from David.
5) Three reg_state->id fixes in the verifier, from Eduard.
6) Optimize bpf_mem_alloc by reusing elements from free_by_rcu, from Hou.
7) Refactor dynptr handling in the verifier, from Kumar.
8) Remove the "/sys" mount and umount dance in {open,close}_netns
in bpf selftests, from Martin.
9) Enable sleepable support for cgrp local storage, from Yonghong.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (74 commits)
selftests/bpf: test case for relaxed prunning of active_lock.id
selftests/bpf: Add pruning test case for bpf_spin_lock
bpf: use check_ids() for active_lock comparison
selftests/bpf: verify states_equal() maintains idmap across all frames
bpf: states_equal() must build idmap for all function frames
selftests/bpf: test cases for regsafe() bug skipping check_id()
bpf: regsafe() must not skip check_ids()
docs/bpf: Add documentation for BPF_MAP_TYPE_SK_STORAGE
selftests/bpf: Add test for dynptr reinit in user_ringbuf callback
bpf: Use memmove for bpf_dynptr_{read,write}
bpf: Move PTR_TO_STACK alignment check to process_dynptr_func
bpf: Rework check_func_arg_reg_off
bpf: Rework process_dynptr_func
bpf: Propagate errors from process_* checks in check_func_arg
bpf: Refactor ARG_PTR_TO_DYNPTR checks into process_dynptr_func
bpf: Skip rcu_barrier() if rcu_trace_implies_rcu_gp() is true
bpf: Reuse freed element in free_by_rcu during allocation
selftests/bpf: Bring test_offload.py back to life
bpf: Fix comment error in fixup_kfunc_call function
bpf: Do not zero-extend kfunc return values
...
====================
Link: https://lore.kernel.org/r/20221212024701.73809-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
linux-can-next-for-6.2-20221212
this is a pull request of 39 patches for net-next/master.
The first 2 patches are by me fix a warning and coding style in the
kvaser_usb driver.
Vivek Yadav's patch sorts the includes of the m_can driver.
Biju Das contributes 5 patches for the rcar_canfd driver improve the
support for different IP core variants.
Jean Delvare's patch for the ctucanfd drops the dependency on
COMPILE_TEST.
Vincent Mailhol's patch sorts the includes of the etas_es58x driver.
Haibo Chen's contributes 2 patches that add i.MX93 support to the
flexcan driver.
Lad Prabhakar's patch updates the dt-bindings documentation of the
rcar_canfd driver.
Minghao Chi's patch converts the c_can platform driver to
devm_platform_get_and_ioremap_resource().
In the next 7 patches Vincent Mailhol adds devlink support to the
etas_es58x driver to report firmware, bootloader and hardware version.
Xu Panda's patch converts a strncpy() -> strscpy() in the ucan driver.
Ye Bin's patch removes a useless parameter from the AF_CAN protocol.
The next 2 patches by Vincent Mailhol and remove unneeded or unused
pointers to struct usb_interface in device's priv struct in the ucan
and gs_usb driver.
Vivek Yadav's patch cleans up the usage of the RAM initialization in
the m_can driver.
A patch by me add support for SO_MARK to the AF_CAN protocol.
Geert Uytterhoeven's patch fixes the number of CAN channels in the
rcan_canfd bindings documentation.
In the last 11 patches Markus Schneider-Pargmann optimizes the
register access in the t_can driver and cleans up the tcan glue
driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two nat functions are nearly the same in both OVS and
TC code, (ovs_)ct_nat_execute() and ovs_ct_nat/tcf_ct_act_nat().
This patch creates nf_nat_ovs.c under netfilter and moves them
there then exports nf_ct_nat() so that it can be shared by both
OVS and TC, and keeps the nat (type) check and nat flag update
in OVS and TC's own place, as these parts are different between
OVS and TC.
Note that in OVS nat function it was using skb->protocol to get
the proto as it already skips vlans in key_extract(), while it
doesn't in TC, and TC has to call skb_protocol() to get proto.
So in nf_ct_nat_execute(), we keep using skb_protocol() which
works for both OVS and TC contrack.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Aaron Conole <aconole@redhat.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now, it's possible to convert USO vnet packets from/to skb.
Added support for GSO_UDP_L4 offload.
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added new GSO type for USO: VIRTIO_NET_HDR_GSO_UDP_L4.
Feature VIRTIO_NET_F_HOST_USO allows to enable NETIF_F_GSO_UDP_L4.
Separated VIRTIO_NET_F_GUEST_USO4 & VIRTIO_NET_F_GUEST_USO6 features
required for Windows guests.
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added 2 additional offlloads for USO(IPv4 & IPv6).
Separate offloads are required for Windows VM guests,
g.e. Windows may set USO rx only for IPv4.
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
verifier.c:states_equal() must maintain register ID mapping across all
function frames. Otherwise the following example might be erroneously
marked as safe:
main:
fp[-24] = map_lookup_elem(...) ; frame[0].fp[-24].id == 1
fp[-32] = map_lookup_elem(...) ; frame[0].fp[-32].id == 2
r1 = &fp[-24]
r2 = &fp[-32]
call foo()
r0 = 0
exit
foo:
0: r9 = r1
1: r8 = r2
2: r7 = ktime_get_ns()
3: r6 = ktime_get_ns()
4: if (r6 > r7) goto skip_assign
5: r9 = r8
skip_assign: ; <--- checkpoint
6: r9 = *r9 ; (a) frame[1].r9.id == 2
; (b) frame[1].r9.id == 1
7: if r9 == 0 goto exit: ; mark_ptr_or_null_regs() transfers != 0 info
; for all regs sharing ID:
; (a) r9 != 0 => &frame[0].fp[-32] != 0
; (b) r9 != 0 => &frame[0].fp[-24] != 0
8: r8 = *r8 ; (a) r8 == &frame[0].fp[-32]
; (b) r8 == &frame[0].fp[-32]
9: r0 = *r8 ; (a) safe
; (b) unsafe
exit:
10: exit
While processing call to foo() verifier considers the following
execution paths:
(a) 0-10
(b) 0-4,6-10
(There is also path 0-7,10 but it is not interesting for the issue at
hand. (a) is verified first.)
Suppose that checkpoint is created at (6) when path (a) is verified,
next path (b) is verified and (6) is reached.
If states_equal() maintains separate 'idmap' for each frame the
mapping at (6) for frame[1] would be empty and
regsafe(r9)::check_ids() would add a pair 2->1 and return true,
which is an error.
If states_equal() maintains single 'idmap' for all frames the mapping
at (6) would be { 1->1, 2->2 } and regsafe(r9)::check_ids() would
return false when trying to add a pair 2->1.
This issue was suggested in the following discussion:
https://lore.kernel.org/bpf/CAEf4BzbFB5g4oUfyxk9rHy-PJSLQ3h8q9mV=rVoXfr_JVm8+1Q@mail.gmail.com/
Suggested-by: Andrii Nakryiko <andrii.nakryiko@gmail.com>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20221209135733.28851-4-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Steffen Klassert says:
====================
ipsec-next 2022-12-09
1) Add xfrm packet offload core API.
From Leon Romanovsky.
2) Add xfrm packet offload support for mlx5.
From Leon Romanovsky and Raed Salem.
3) Fix a typto in a error message.
From Colin Ian King.
* tag 'ipsec-next-2022-12-09' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next: (38 commits)
xfrm: Fix spelling mistake "oflload" -> "offload"
net/mlx5e: Open mlx5 driver to accept IPsec packet offload
net/mlx5e: Handle ESN update events
net/mlx5e: Handle hardware IPsec limits events
net/mlx5e: Update IPsec soft and hard limits
net/mlx5e: Store all XFRM SAs in Xarray
net/mlx5e: Provide intermediate pointer to access IPsec struct
net/mlx5e: Skip IPsec encryption for TX path without matching policy
net/mlx5e: Add statistics for Rx/Tx IPsec offloaded flows
net/mlx5e: Improve IPsec flow steering autogroup
net/mlx5e: Configure IPsec packet offload flow steering
net/mlx5e: Use same coding pattern for Rx and Tx flows
net/mlx5e: Add XFRM policy offload logic
net/mlx5e: Create IPsec policy offload tables
net/mlx5e: Generalize creation of default IPsec miss group and rule
net/mlx5e: Group IPsec miss handles into separate struct
net/mlx5e: Make clear what IPsec rx_err does
net/mlx5e: Flatten the IPsec RX add rule path
net/mlx5e: Refactor FTE setup code to be more clear
net/mlx5e: Move IPsec flow table creation to separate function
...
====================
Link: https://lore.kernel.org/r/20221209093310.4018731-1-steffen.klassert@secunet.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Saeed Mahameed says:
====================
mlx5-updates-2022-12-08
1) Support range match action in SW steering
Yevgeny Kliteynik says:
=======================
The following patch series adds support for a range match action in
SW Steering.
SW steering is able to match only on the exact values of the packet fields,
as requested by the user: the user provides mask for the fields that are of
interest, and the exact values to be matched on when the traffic is handled.
The following patch series add new type of action - Range Match, where the
user provides a field to be matched on and a range of values (min to max)
that will be considered as hit.
There are several new notions that were implemented in order to support
Range Match:
- MATCH_RANGES Steering Table Entry (STE): the new STE type that allows
matching the packets' fields on the range of values instead of a specific
value.
- Match Definer: this is a general FW object that defines which fields
in the packet will be referenced by the mask and tag of each STE.
Match definer ID is part of STE fields, and it defines how the HW needs
to interpret the STE's mask/tag values.
Till now SW steering used the definers that were managed by FW and
implemented the STE layout as described by the HW spec.
Now that we're adding a new type of STE, SW steering needs to also be
able to define this new STE's layout, and this is do
=======================
2) From OZ add support for meter mtu offload
2.1: Refactor the code to allow both metering and range post actions as a
pre-step for adding police mtu offload support.
2.2: Instantiate mtu green/red flow tables with a single match-all rule.
Add the green/red actions to the hit/miss table accordingly
2.3: Initialize the meter object with the TC police mtu parameter.
Use the hardware range match action feature.
3) From MaorD, support routes with more than 2 nexthops in multipath
4) Michael and Or, improve and extend vport representor counters.
* tag 'mlx5-updates-2022-12-08' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Expose steering dropped packets counter
net/mlx5: Refactor and expand rep vport stat group
net/mlx5e: multipath, support routes with more than 2 nexthops
net/mlx5e: TC, add support for meter mtu offload
net/mlx5e: meter, add mtu post meter tables
net/mlx5e: meter, refactor to allow multiple post meter tables
net/mlx5: DR, Add support for range match action
net/mlx5: DR, Add function that tells if STE miss addr has been initialized
net/mlx5: DR, Some refactoring of miss address handling
net/mlx5: DR, Manage definers with refcounts
net/mlx5: DR, Handle FT action in a separate function
net/mlx5: DR, Rework is_fw_table function
net/mlx5: DR, Add functions to create/destroy MATCH_DEFINER general object
net/mlx5: fs, add match on ranges API
net/mlx5: mlx5_ifc updates for MATCH_DEFINER general object
====================
Link: https://lore.kernel.org/r/20221209001420.142794-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support to count upall packets, when kmod of openvswitch
upcall to count the number of packets for upcall succeed and
failed, which is a better way to see how many packets upcalled
on every interfaces.
Signed-off-by: wangchuanlei <wangchuanlei@inspur.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rhashtable currently only does bh-safe synchronization making it impossible
to use from irq-safe contexts. Switch it to use irq-safe synchronization to
remove the restriction.
v2: Update the lock functions to return the ulong flags value and unlock
functions to take the value directly instead of passing around the
pointer. Suggested by Linus.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: David Vernet <dvernet@meta.com>
Acked-by: Josh Don <joshdon@google.com>
Acked-by: Hao Luo <haoluo@google.com>
Acked-by: Barret Rhoden <brho@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On kernels using retpoline as a spectrev2 mitigation,
optimize actions and filters that are compiled as built-ins into a direct call.
On subsequent patches we expose the classifiers and actions functions
and wire up the wrapper into tc.
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an option to initialize SOF_TIMESTAMPING_OPT_ID for TCP from
write_seq sockets instead of snd_una.
This should have been the behavior from the start. Because processes
may now exist that rely on the established behavior, do not change
behavior of the existing option, but add the right behavior with a new
flag. It is encouraged to always set SOF_TIMESTAMPING_OPT_ID_TCP on
stream sockets along with the existing SOF_TIMESTAMPING_OPT_ID.
Intuitively the contract is that the counter is zero after the
setsockopt, so that the next write N results in a notification for
the last byte N - 1.
On idle sockets snd_una == write_seq and this holds for both. But on
sockets with data in transmission, snd_una records the unacked offset
in the stream. This depends on the ACK response from the peer. A
process cannot learn this in a race free manner (ioctl SIOCOUTQ is one
racy approach).
write_seq records the offset at the last byte written by the process.
This is a better starting point. It matches the intuitive contract in
all circumstances, unaffected by external behavior.
The new timestamp flag necessitates increasing sk_tsflags to 32 bits.
Move the field in struct sock to avoid growing the socket (for some
common CONFIG variants). The UAPI interface so_timestamping.flags is
already int, so 32 bits wide.
Reported-by: Sotirios Delimanolis <sotodel@meta.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20221207143701.29861-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Recently, user ringbuf support introduced a PTR_TO_DYNPTR register type
for use in callback state, because in case of user ringbuf helpers,
there is no dynptr on the stack that is passed into the callback. To
reflect such a state, a special register type was created.
However, some checks have been bypassed incorrectly during the addition
of this feature. First, for arg_type with MEM_UNINIT flag which
initialize a dynptr, they must be rejected for such register type.
Secondly, in the future, there are plans to add dynptr helpers that
operate on the dynptr itself and may change its offset and other
properties.
In all of these cases, PTR_TO_DYNPTR shouldn't be allowed to be passed
to such helpers, however the current code simply returns 0.
The rejection for helpers that release the dynptr is already handled.
For fixing this, we take a step back and rework existing code in a way
that will allow fitting in all classes of helpers and have a coherent
model for dealing with the variety of use cases in which dynptr is used.
First, for ARG_PTR_TO_DYNPTR, it can either be set alone or together
with a DYNPTR_TYPE_* constant that denotes the only type it accepts.
Next, helpers which initialize a dynptr use MEM_UNINIT to indicate this
fact. To make the distinction clear, use MEM_RDONLY flag to indicate
that the helper only operates on the memory pointed to by the dynptr,
not the dynptr itself. In C parlance, it would be equivalent to taking
the dynptr as a point to const argument.
When either of these flags are not present, the helper is allowed to
mutate both the dynptr itself and also the memory it points to.
Currently, the read only status of the memory is not tracked in the
dynptr, but it would be trivial to add this support inside dynptr state
of the register.
With these changes and renaming PTR_TO_DYNPTR to CONST_PTR_TO_DYNPTR to
better reflect its usage, it can no longer be passed to helpers that
initialize a dynptr, i.e. bpf_dynptr_from_mem, bpf_ringbuf_reserve_dynptr.
A note to reviewers is that in code that does mark_stack_slots_dynptr,
and unmark_stack_slots_dynptr, we implicitly rely on the fact that
PTR_TO_STACK reg is the only case that can reach that code path, as one
cannot pass CONST_PTR_TO_DYNPTR to helpers that don't set MEM_RDONLY. In
both cases such helpers won't be setting that flag.
The next patch will add a couple of selftest cases to make sure this
doesn't break.
Fixes: 2057156738 ("bpf: Add bpf_user_ringbuf_drain() helper")
Acked-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20221207204141.308952-4-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
ARG_PTR_TO_DYNPTR is akin to ARG_PTR_TO_TIMER, ARG_PTR_TO_KPTR, where
the underlying register type is subjected to more special checks to
determine the type of object represented by the pointer and its state
consistency.
Move dynptr checks to their own 'process_dynptr_func' function so that
is consistent and in-line with existing code. This also makes it easier
to reuse this code for kfunc handling.
Then, reuse this consolidated function in kfunc dynptr handling too.
Note that for kfuncs, the arg_type constraint of DYNPTR_TYPE_LOCAL has
been lifted.
Acked-by: David Vernet <void@manifault.com>
Acked-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20221207204141.308952-2-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Range is a new flow destination type which allows matching on
a range of values instead of matching on a specific value.
Range flow destination has the following fields:
- hit_ft: flow table to forward the traffic in case of hit
- miss_ft: flow table to forward the traffic in case of miss
- field: which packet characteristic to match on
- min: minimal value for the selected field
- max: maximal value for the selected field
Note:
- In order to match, the value in the packet should meet
the following criteria: min <= value < max
- Currently, the only supported field type is L2 packet length
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Update full structure of match definer and add an ID of
the SELECT match definer type.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth, can and netfilter.
Current release - new code bugs:
- bonding: ipv6: correct address used in Neighbour Advertisement
parsing (src vs dst typo)
- fec: properly scope IRQ coalesce setup during link up to supported
chips only
Previous releases - regressions:
- Bluetooth fixes for fake CSR clones (knockoffs):
- re-add ERR_DATA_REPORTING quirk
- fix crash when device is replugged
- Bluetooth:
- silence a user-triggerable dmesg error message
- L2CAP: fix u8 overflow, oob access
- correct vendor codec definition
- fix support for Read Local Supported Codecs V2
- ti: am65-cpsw: fix RGMII configuration at SPEED_10
- mana: fix race on per-CQ variable NAPI work_done
Previous releases - always broken:
- af_unix: diag: fetch user_ns from in_skb in unix_diag_get_exact(),
avoid null-deref
- af_can: fix NULL pointer dereference in can_rcv_filter
- can: slcan: fix UAF with a freed work
- can: can327: flush TX_work on ldisc .close()
- macsec: add missing attribute validation for offload
- ipv6: avoid use-after-free in ip6_fragment()
- nft_set_pipapo: actually validate intervals in fields after the
first one
- mvneta: prevent oob access in mvneta_config_rss()
- ipv4: fix incorrect route flushing when table ID 0 is used, or when
source address is deleted
- phy: mxl-gpy: add workaround for IRQ bug on GPY215B and GPY215C"
* tag 'net-6.1-rc9' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (77 commits)
net: dsa: sja1105: avoid out of bounds access in sja1105_init_l2_policing()
s390/qeth: fix use-after-free in hsci
macsec: add missing attribute validation for offload
net: mvneta: Fix an out of bounds check
net: thunderbolt: fix memory leak in tbnet_open()
ipv6: avoid use-after-free in ip6_fragment()
net: plip: don't call kfree_skb/dev_kfree_skb() under spin_lock_irq()
net: phy: mxl-gpy: add MDINT workaround
net: dsa: mv88e6xxx: accept phy-mode = "internal" for internal PHY ports
xen/netback: don't call kfree_skb() under spin_lock_irqsave()
dpaa2-switch: Fix memory leak in dpaa2_switch_acl_entry_add() and dpaa2_switch_acl_entry_remove()
ethernet: aeroflex: fix potential skb leak in greth_init_rings()
tipc: call tipc_lxc_xmit without holding node_read_lock
can: esd_usb: Allow REC and TEC to return to zero
can: can327: flush TX_work on ldisc .close()
can: slcan: fix freed work crash
can: af_can: fix NULL pointer dereference in can_rcv_filter
net: dsa: sja1105: fix memory leak in sja1105_setup_devlink_regions()
ipv4: Fix incorrect route flushing when table ID 0 is used
ipv4: Fix incorrect route flushing when source address is deleted
...
memcg_write_event_control() accesses the dentry->d_name of the specified
control fd to route the write call. As a cgroup interface file can't be
renamed, it's safe to access d_name as long as the specified file is a
regular cgroup file. Also, as these cgroup interface files can't be
removed before the directory, it's safe to access the parent too.
Prior to 347c4a8747 ("memcg: remove cgroup_event->cft"), there was a
call to __file_cft() which verified that the specified file is a regular
cgroupfs file before further accesses. The cftype pointer returned from
__file_cft() was no longer necessary and the commit inadvertently
dropped the file type check with it allowing any file to slip through.
With the invarients broken, the d_name and parent accesses can now race
against renames and removals of arbitrary files and cause
use-after-free's.
Fix the bug by resurrecting the file type check in __file_cft(). Now
that cgroupfs is implemented through kernfs, checking the file
operations needs to go through a layer of indirection. Instead, let's
check the superblock and dentry type.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 347c4a8747 ("memcg: remove cgroup_event->cft")
Cc: stable@kernel.org # v3.14+
Reported-by: Jann Horn <jannh@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Expose port function commands to enable / disable migratable
capability, this is used to set the port function as migratable.
Live migration is the process of transferring a live virtual machine
from one physical host to another without disrupting its normal
operation.
In order for a VM to be able to perform LM, all the VM components must
be able to perform migration. e.g.: to be migratable.
In order for VF to be migratable, VF must be bound to VFIO driver with
migration support.
When migratable capability is enabled for a function of the port, the
device is making the necessary preparations for the function to be
migratable, which might include disabling features which cannot be
migrated.
Example of LM with migratable function configuration:
Set migratable of the VF's port function.
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0
vfnum 1
function:
hw_addr 00:00:00:00:00:00 migratable disable
$ devlink port function set pci/0000:06:00.0/2 migratable enable
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0
vfnum 1
function:
hw_addr 00:00:00:00:00:00 migratable enable
Bind VF to VFIO driver with migration support:
$ echo <pci_id> > /sys/bus/pci/devices/0000:08:00.0/driver/unbind
$ echo mlx5_vfio_pci > /sys/bus/pci/devices/0000:08:00.0/driver_override
$ echo <pci_id> > /sys/bus/pci/devices/0000:08:00.0/driver/bind
Attach VF to the VM.
Start the VM.
Perform LM.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Downstream patch requires to get other function GENERAL2 caps while
mlx5_vport_get_other_func_cap() gets only one type of caps (general).
Rename it to represent this and introduce a generic implementation
of mlx5_vport_get_other_func_cap().
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Acked-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Expose port function commands to enable / disable RoCE, this is used to
control the port RoCE device capabilities.
When RoCE is disabled for a function of the port, function cannot create
any RoCE specific resources (e.g GID table).
It also saves system memory utilization. For example disabling RoCE enable a
VF/SF saves 1 Mbytes of system memory per function.
Example of a PCI VF port which supports function configuration:
Set RoCE of the VF's port function.
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0
vfnum 1
function:
hw_addr 00:00:00:00:00:00 roce enable
$ devlink port function set pci/0000:06:00.0/2 roce disable
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0
vfnum 1
function:
hw_addr 00:00:00:00:00:00 roce disable
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce IFC related capabilities to enable setting VF to be able to
perform live migration. e.g.: to be migratable.
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Acked-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stefan Schmidt says:
====================
ieee802154-next 2022-12-05
Miquel continued his work towards full scanning support. For this,
we now allow the creation of dedicated coordinator interfaces
to allow a PAN coordinator to serve in the network and set
the needed address filters with the hardware.
On top of this we have the first part to allow scanning for available
15.4 networks. A new netlink scan group, within the existing nl802154
API, was added.
In addition Miquel fixed two issues that have been introduced in the former
patches to free an skb correctly and clarifying an expression in the stack.
From David Girault we got tracing support when registering new PANs.
* tag 'ieee802154-for-net-next-2022-12-05' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan-next:
mac802154: Trace the registration of new PANs
ieee802154: Advertize coordinators discovery
mac802154: Allow the creation of coordinator interfaces
mac802154: Clarify an expression
mac802154: Move an skb free within the rx path
====================
Link: https://lore.kernel.org/r/20221205131909.1871790-1-stefan@datenfreihafen.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge commit 5b481acab4 ("bpf: do not rely on ALLOW_ERROR_INJECTION for fmod_ret")
from hid tree into bpf-next.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
If a cookie expires from the LRU and the LRU_DISCARD flag is set, but
the state machine has not run yet, it's possible another thread can call
fscache_use_cookie and begin to use it.
When the cookie_worker finally runs, it will see the LRU_DISCARD flag
set, transition the cookie->state to LRU_DISCARDING, which will then
withdraw the cookie. Once the cookie is withdrawn the object is removed
the below oops will occur because the object associated with the cookie
is now NULL.
Fix the oops by clearing the LRU_DISCARD bit if another thread uses the
cookie before the cookie_worker runs.
BUG: kernel NULL pointer dereference, address: 0000000000000008
...
CPU: 31 PID: 44773 Comm: kworker/u130:1 Tainted: G E 6.0.0-5.dneg.x86_64 #1
Hardware name: Google Compute Engine/Google Compute Engine, BIOS Google 08/26/2022
Workqueue: events_unbound netfs_rreq_write_to_cache_work [netfs]
RIP: 0010:cachefiles_prepare_write+0x28/0x90 [cachefiles]
...
Call Trace:
netfs_rreq_write_to_cache_work+0x11c/0x320 [netfs]
process_one_work+0x217/0x3e0
worker_thread+0x4a/0x3b0
kthread+0xd6/0x100
Fixes: 12bb21a29c ("fscache: Implement cookie user counting and resource pinning")
Reported-by: Daire Byrne <daire.byrne@gmail.com>
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Daire Byrne <daire@dneg.com>
Link: https://lore.kernel.org/r/20221117115023.1350181-1-dwysocha@redhat.com/ # v1
Link: https://lore.kernel.org/r/20221117142915.1366990-1-dwysocha@redhat.com/ # v2
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
BPF verifier marks some instructions as prune points. Currently these
prune points serve two purposes.
It's a point where verifier tries to find previously verified state and
check current state's equivalence to short circuit verification for
current code path.
But also currently it's a point where jump history, used for precision
backtracking, is updated. This is done so that non-linear flow of
execution could be properly backtracked.
Such coupling is coincidental and unnecessary. Some prune points are not
part of some non-linear jump path, so don't need update of jump history.
On the other hand, not all instructions which have to be recorded in
jump history necessarily are good prune points.
This patch splits prune and jump points into independent flags.
Currently all prune points are marked as jump points to minimize amount
of changes in this patch, but next patch will perform some optimization
of prune vs jmp point placement.
No functional changes are intended.
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20221206233345.438540-2-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This change adds xfrm metadata helpers using the unstable kfunc call
interface for the TC-BPF hooks. This allows steering traffic towards
different IPsec connections based on logic implemented in bpf programs.
This object is built based on the availability of BTF debug info.
When setting the xfrm metadata, percpu metadata dsts are used in order
to avoid allocating a metadata dst per packet.
In order to guarantee safe module unload, the percpu dsts are allocated
on first use and never freed. The percpu pointer is stored in
net/core/filter.c so that it can be reused on module reload.
The metadata percpu dsts take ownership of the original skb dsts so
that they may be used as part of the xfrm transmission logic - e.g.
for MTU calculations.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Link: https://lore.kernel.org/r/20221203084659.1837829-3-eyal.birger@gmail.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Add netlink based support for "ethtool -x <dev> [context x]"
command by implementing ETHTOOL_MSG_RSS_GET netlink message.
This is equivalent to functionality provided via ETHTOOL_GRSSH
in ioctl path. It sends RSS table, hash key and hash function
of an interface to user space.
This patch implements existing functionality available
in ioctl path and enables addition of new RSS context
based parameters in future.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Link: https://lore.kernel.org/r/20221202002555.241580-1-sudheer.mogilappagari@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David Howells says:
====================
rxrpc: Increasing SACK size and moving away from softirq, parts 2 & 3
Here are the second and third parts of patches in the process of moving
rxrpc from doing a lot of its stuff in softirq context to doing it in an
I/O thread in process context and thereby making it easier to support a
larger SACK table.
The full description is in the description for the first part[1] which is
already in net-next.
The second part includes some cleanups, adds some testing and overhauls
some tracing:
(1) Remove declaration of rxrpc_kernel_call_is_complete() as the
definition is no longer present.
(2) Remove the knet() and kproto() macros in favour of using tracepoints.
(3) Remove handling of duplicate packets from recvmsg. The input side
isn't now going to insert overlapping/duplicate packets into the
recvmsg queue.
(4) Don't use the rxrpc_conn_parameters struct in the rxrpc_connection or
rxrpc_bundle structs - rather put the members in directly.
(5) Extract the abort code from a received abort packet right up front
rather than doing it in multiple places later.
(6) Use enums and symbol lists rather than __builtin_return_address() to
indicate where a tracepoint was triggered for local, peer, conn, call
and skbuff tracing.
(7) Add a refcount tracepoint for the rxrpc_bundle struct.
(8) Implement an in-kernel server for the AFS rxperf testing program to
talk to (enabled by a Kconfig option).
This is tagged as rxrpc-next-20221201-a.
The third part introduces the I/O thread and switches various bits over to
running there:
(1) Fix call timers and call and connection workqueues to not hold refs on
the rxrpc_call and rxrpc_connection structs to thereby avoid messy
cleanup when the last ref is put in softirq mode.
(2) Split input.c so that the call packet processing bits are separate
from the received packet distribution bits. Call packet processing
gets bumped over to the call event handler.
(3) Create a per-local endpoint I/O thread. Barring some tiny bits that
still get done in softirq context, all packet reception, processing
and transmission is done in this thread. That will allow a load of
locking to be removed.
(4) Perform packet processing and error processing from the I/O thread.
(5) Provide a mechanism to process call event notifications in the I/O
thread rather than queuing a work item for that call.
(6) Move data and ACK transmission into the I/O thread. ACKs can then be
transmitted at the point they're generated rather than getting
delegated from softirq context to some process context somewhere.
(7) Move call and local processor event handling into the I/O thread.
(8) Move cwnd degradation to after packets have been transmitted so that
they don't shorten the window too quickly.
A bunch of simplifications can then be done:
(1) The input_lock is no longer necessary as exclusion is achieved by
running the code in the I/O thread only.
(2) Don't need to use sk->sk_receive_queue.lock to guard socket state
changes as the socket mutex should suffice.
(3) Don't take spinlocks in RCU callback functions as they get run in
softirq context and thus need _bh annotations.
(4) RCU is then no longer needed for the peer's error_targets list.
(5) Simplify the skbuff handling in the receive path by dropping the ref
in the basic I/O thread loop and getting an extra ref as and when we
need to queue the packet for recvmsg or another context.
(6) Get the peer address earlier in the input process and pass it to the
users so that we only do it once.
This is tagged as rxrpc-next-20221201-b.
Changes:
========
ver #2)
- Added a patch to change four assertions into warnings in rxrpc_read()
and fixed a checker warning from a __user annotation that should have
been removed..
- Change a min() to min_t() in rxperf as PAGE_SIZE doesn't seem to match
type size_t on i386.
- Three error handling issues in rxrpc_new_incoming_call():
- If not DATA or not seq #1, should drop the packet, not abort.
- Fix a goto that went to the wrong place, dropping a non-held lock.
- Fix an rcu_read_lock that should've been an unlock.
Tested-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: kafs-testing+fedora36_64checkkafs-build-144@auristor.com
Link: https://lore.kernel.org/r/166794587113.2389296.16484814996876530222.stgit@warthog.procyon.org.uk/ [1]
Link: https://lore.kernel.org/r/166982725699.621383.2358362793992993374.stgit@warthog.procyon.org.uk/ # v1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tegra MGBE ethernet controller requires that the SERDES link is
powered-up after the PHY link is up, otherwise the link fails to
become ready following a resume from suspend. Add a variable to indicate
that the SERDES link must be powered-up after the PHY link.
Signed-off-by: Revanth Kumar Uppala <ruppala@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both in RX and TX, the traffic that performs IPsec packet offload
transformation is accounted by HW. It is needed to properly handle
hard limits that require to drop the packet.
It means that XFRM core needs to update internal counters with the one
that accounted by the HW, so new callbacks are introduced in this patch.
In case of soft or hard limit is occurred, the driver should call to
xfrm_state_check_expire() that will perform key rekeying exactly as
done by XFRM core.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Traffic received by device with enabled IPsec packet offload should
be forwarded to the stack only after decryption, packet headers and
trailers removed.
Such packets are expected to be seen as normal (non-XFRM) ones, while
not-supported packets should be dropped by the HW.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Extend netlink interface to add and delete XFRM policy from the device.
This functionality is a first step to implement packet IPsec offload solution.
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In the next patches, the xfrm core code will be extended to support
new type of offload - packet offload. In that mode, both policy and state
should be specially configured in order to perform whole offloaded data
path.
Full offload takes care of encryption, decryption, encapsulation and
other operations with headers.
As this mode is new for XFRM policy flow, we can "start fresh" with flag
bits and release first and second bit for future use.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Martin mentioned that the verifier cannot assume arguments from
LSM hook sk_alloc_security being trusted since after the hook
is called, the sk ref_count is set to 1. This will overwrite
the ref_count changed by the bpf program and may cause ref_count
underflow later on.
I then further checked some other hooks. For example,
for bpf_lsm_file_alloc() hook in fs/file_table.c,
f->f_cred = get_cred(cred);
error = security_file_alloc(f);
if (unlikely(error)) {
file_free_rcu(&f->f_rcuhead);
return ERR_PTR(error);
}
atomic_long_set(&f->f_count, 1);
The input parameter 'f' to security_file_alloc() cannot be trusted
as well.
Specifically, I investiaged bpf_map/bpf_prog/file/sk/task alloc/free
lsm hooks. Except bpf_map_alloc and task_alloc, arguments for all other
hooks should not be considered as trusted. This may not be a complete
list, but it covers common usage for sk and task.
Fixes: 3f00c52393 ("bpf: Allow trusted pointers to be passed to KF_TRUSTED_ARGS kfuncs")
Signed-off-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/r/20221203204954.2043348-1-yhs@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
