These WWAN network interface operations (create/delete/open/close)
are already protected by RTNL lock, i.e., wwan_ops.newlink(),
wwan_ops.dellink(), net_device_ops.ndo_open() and
net_device.ndo_stop() are called with RTNL lock held.
Therefore, this patch removes the unnecessary if_mutex.
Signed-off-by: Zhaoping Shu <zhaoping.shu@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MHI driver registers network device without setting the
needs_free_netdev flag, and does NOT call free_netdev() when
unregisters network device, which causes a memory leak.
This patch sets needs_free_netdev to true when registers
network device, which makes netdev subsystem call free_netdev()
automatically after unregister_netdevice().
Fixes: aa730a9905 ("net: wwan: Add MHI MBIM network driver")
Signed-off-by: HW He <hw.he@mediatek.com>
Signed-off-by: Zhaoping Shu <zhaoping.shu@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IOSM driver registers network device without setting the
needs_free_netdev flag, and does NOT call free_netdev() when
unregisters network device, which causes a memory leak.
This patch sets needs_free_netdev to true when registers
network device, which makes netdev subsystem call free_netdev()
automatically after unregister_netdevice().
Fixes: 2a54f2c779 ("net: iosm: net driver")
Signed-off-by: HW He <hw.he@mediatek.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Zhaoping Shu <zhaoping.shu@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When following tests are performed, it will cause dev reference counting
leakage.
a)ip link add bond2 type bond mode balance-rr
b)ip link set bond2 up
c)ifenslave -f bond2 rose1
d)ip link del bond2
When new bond device is created, the default type of the bond device is
ether. And the bond device is up, bpq_device_event() receives the message
and creates a new bpq device. In this case, the reference count value of
dev is hold once. But after "ifenslave -f bond2 rose1" command is
executed, the type of the bond device is changed to rose. When the bond
device is unregistered, bpq_device_event() will not put the dev reference
count.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When following tests are performed, it will cause dev reference counting
leakage.
a)ip link add bond2 type bond mode balance-rr
b)ip link set bond2 up
c)ifenslave -f bond2 rose1
d)ip link del bond2
When new bond device is created, the default type of the bond device is
ether. And the bond device is up, lapbeth_device_event() receives the
message and creates a new lapbeth device. In this case, the reference
count value of dev is hold once. But after "ifenslave -f bond2 rose1"
command is executed, the type of the bond device is changed to rose. When
the bond device is unregistered, lapbeth_device_event() will not put the
dev reference count.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running under PV, the guest's TOD clock is under control of the
ultravisor and the hypervisor isn't allowed to change it. Hence, don't
allow userspace to change the guest's TOD clock by returning
-EOPNOTSUPP.
When userspace changes the guest's TOD clock, KVM updates its
kvm.arch.epoch field and, in addition, the epoch field in all state
descriptions of all VCPUs.
But, under PV, the ultravisor will ignore the epoch field in the state
description and simply overwrite it on next SIE exit with the actual
guest epoch. This leads to KVM having an incorrect view of the guest's
TOD clock: it has updated its internal kvm.arch.epoch field, but the
ultravisor ignores the field in the state description.
Whenever a guest is now waiting for a clock comparator, KVM will
incorrectly calculate the time when the guest should wake up, possibly
causing the guest to sleep for much longer than expected.
With this change, kvm_s390_set_tod() will now take the kvm->lock to be
able to call kvm_s390_pv_is_protected(). Since kvm_s390_set_tod_clock()
also takes kvm->lock, use __kvm_s390_set_tod_clock() instead.
The function kvm_s390_set_tod_clock is now unused, hence remove it.
Update the documentation to indicate the TOD clock attr calls can now
return -EOPNOTSUPP.
Fixes: 0f30350471 ("KVM: s390: protvirt: Do only reset registers that are accessible")
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Signed-off-by: Nico Boehr <nrb@linux.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20221011160712.928239-2-nrb@linux.ibm.com
Message-Id: <20221011160712.928239-2-nrb@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
When ethtool config rx-vlan-filter, the driver will send
control command to firmware, then set to hardware in this patch.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
HINIC has a mailbox for PF-VF communication and the VF driver
could send port control command to PF driver via mailbox.
The control command only can be set to register in PF,
so add support in PF driver for VF PMD driver control
command when VF PMD driver work with linux PF driver.
Then, no need to add handlers to nic_vf_cmd_msg_handler[],
because the host driver just forwards it to the firmware.
Actually the firmware works on a coprocessor MGMT_CPU(inside the NIC)
which will recv and deal with these commands.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
The print cmd code is in hex, so using hex cmd code intead of
decimal is easy to check the value with print info.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
'reg' without any constraints allows multiple items which is not the
intention in DSA port schema (as physical port is expected to have only
one address).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'reg' without any constraints allows multiple items which is not the
intention for Ethernet controller's port number.
Constrain the 'reg' on AX88178 and LAN95xx USB Ethernet Controllers.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support mode switch properly, which is not available before.
If SoC has two Ethernet controllers, by setting both of them into MII
mode, the first controller enters GMII mode, while the second
controller is effectively disabled. This requires configuring (and
maybe enabling) the second controller in the device tree, even though
it cannot be used.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2 improvements for the Chromebook handling in
acpi_video_get_backlight_type():
1. Also check for the "GOOG000C" ACPI HID used on some models
2. Move the Chromebook check to above the ACPI-video check normally
Chromebooks don't have ACPI video backlight support, but when
flashed with upstream coreboot builds they may have ACPI video
backlight support, but native should still be used/preferred then.
Suggested-by: Mr. Chromebox <mrchromebox@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Pull cxl fixes from Dan Williams:
"Several fixes for CXL region creation crashes, leaks and failures.
This is mainly fallout from the original implementation of dynamic CXL
region creation (instantiate new physical memory pools) that arrived
in v6.0-rc1.
Given the theme of "failures in the presence of pass-through decoders"
this also includes new regression test infrastructure for that case.
Summary:
- Fix region creation crash with pass-through decoders
- Fix region creation crash when no decoder allocation fails
- Fix region creation crash when scanning regions to enforce the
increasing physical address order constraint that CXL mandates
- Fix a memory leak for cxl_pmem_region objects, track 1:N instead of
1:1 memory-device-to-region associations.
- Fix a memory leak for cxl_region objects when regions with active
targets are deleted
- Fix assignment of NUMA nodes to CXL regions by CFMWS (CXL Window)
emulated proximity domains.
- Fix region creation failure for switch attached devices downstream
of a single-port host-bridge
- Fix false positive memory leak of cxl_region objects by recycling
recently used region ids rather than freeing them
- Add regression test infrastructure for a pass-through decoder
configuration
- Fix some mailbox payload handling corner cases"
* tag 'cxl-fixes-for-6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/region: Recycle region ids
cxl/region: Fix 'distance' calculation with passthrough ports
tools/testing/cxl: Add a single-port host-bridge regression config
tools/testing/cxl: Fix some error exits
cxl/pmem: Fix cxl_pmem_region and cxl_memdev leak
cxl/region: Fix cxl_region leak, cleanup targets at region delete
cxl/region: Fix region HPA ordering validation
cxl/pmem: Use size_add() against integer overflow
cxl/region: Fix decoder allocation crash
ACPI: NUMA: Add CXL CFMWS 'nodes' to the possible nodes set
cxl/pmem: Fix failure to account for 8 byte header for writes to the device LSA.
cxl/region: Fix null pointer dereference due to pass through decoder commit
cxl/mbox: Add a check on input payload size
Pull hwmon fixes from Guenter Roeck:
"Fix two regressions:
- Commit 54cc3dbfc1 ("hwmon: (pmbus) Add regulator supply into
macro") resulted in regulator undercount when disabling regulators.
Revert it.
- The thermal subsystem rework caused the scmi driver to no longer
register with the thermal subsystem because index values no longer
match. To fix the problem, the scmi driver now directly registers
with the thermal subsystem, no longer through the hwmon core"
* tag 'hwmon-for-v6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
Revert "hwmon: (pmbus) Add regulator supply into macro"
hwmon: (scmi) Register explicitly with Thermal Framework
Pull perf fixes from Borislav Petkov:
- Add Cooper Lake's stepping to the PEBS guest/host events isolation
fixed microcode revisions checking quirk
- Update Icelake and Sapphire Rapids events constraints
- Use the standard energy unit for Sapphire Rapids in RAPL
- Fix the hw_breakpoint test to fail more graciously on !SMP configs
* tag 'perf_urgent_for_v6.1_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Add Cooper Lake stepping to isolation_ucodes[]
perf/x86/intel: Fix pebs event constraints for SPR
perf/x86/intel: Fix pebs event constraints for ICL
perf/x86/rapl: Use standard Energy Unit for SPR Dram RAPL domain
perf/hw_breakpoint: test: Skip the test if dependencies unmet
Pull x86 fixes from Borislav Petkov:
- Add new Intel CPU models
- Enforce that TDX guests are successfully loaded only on TDX hardware
where virtualization exception (#VE) delivery on kernel memory is
disabled because handling those in all possible cases is "essentially
impossible"
- Add the proper include to the syscall wrappers so that BTF can see
the real pt_regs definition and not only the forward declaration
* tag 'x86_urgent_for_v6.1_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Add several Intel server CPU model numbers
x86/tdx: Panic on bad configs that #VE on "private" memory access
x86/tdx: Prepare for using "INFO" call for a second purpose
x86/syscall: Include asm/ptrace.h in syscall_wrapper header
Pull Kbuild fixes from Masahiro Yamada:
- Use POSIX-compatible grep options
- Document git-related tips for reproducible builds
- Fix a typo in the modpost rule
- Suppress SIGPIPE error message from gcc-ar and llvm-ar
- Fix segmentation fault in the menuconfig search
* tag 'kbuild-fixes-v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: fix segmentation fault in menuconfig search
kbuild: fix SIGPIPE error message for AR=gcc-ar and AR=llvm-ar
kbuild: fix typo in modpost
Documentation: kbuild: Add description of git for reproducible builds
kbuild: use POSIX-compatible grep option
Just a basic s/thig/this swap, fixing up a typo introduced by a commit
added in the 6.1 release.
Fixes: 9cda70f622 ("io_uring: introduce fixed buffer support for io_uring_cmd")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Fix the pKVM stage-1 walker erronously using the stage-2 accessor
- Correctly convert vcpu->kvm to a hyp pointer when generating an
exception in a nVHE+MTE configuration
- Check that KVM_CAP_DIRTY_LOG_* are valid before enabling them
- Fix SMPRI_EL1/TPIDR2_EL0 trapping on VHE
- Document the boot requirements for FGT when entering the kernel at
EL1
x86:
- Use SRCU to protect zap in __kvm_set_or_clear_apicv_inhibit()
- Make argument order consistent for kvcalloc()
- Userspace API fixes for DEBUGCTL and LBRs"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Fix a typo about the usage of kvcalloc()
KVM: x86: Use SRCU to protect zap in __kvm_set_or_clear_apicv_inhibit()
KVM: VMX: Ignore guest CPUID for host userspace writes to DEBUGCTL
KVM: VMX: Fold vmx_supported_debugctl() into vcpu_supported_debugctl()
KVM: VMX: Advertise PMU LBRs if and only if perf supports LBRs
arm64: booting: Document our requirements for fine grained traps with SME
KVM: arm64: Fix SMPRI_EL1/TPIDR2_EL0 trapping on VHE
KVM: Check KVM_CAP_DIRTY_LOG_{RING, RING_ACQ_REL} prior to enabling them
KVM: arm64: Fix bad dereference on MTE-enabled systems
KVM: arm64: Use correct accessor to parse stage-1 PTEs
Pull xen fixes from Juergen Gross:
"One fix for silencing a smatch warning, and a small cleanup patch"
* tag 'for-linus-6.1-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: simplify sysenter and syscall setup
x86/xen: silence smatch warning in pmu_msr_chk_emulated()
Pull ext4 fixes from Ted Ts'o:
"Fix a number of bugs, including some regressions, the most serious of
which was one which would cause online resizes to fail with file
systems with metadata checksums enabled.
Also fix a warning caused by the newly added fortify string checker,
plus some bugs that were found using fuzzed file systems"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix fortify warning in fs/ext4/fast_commit.c:1551
ext4: fix wrong return err in ext4_load_and_init_journal()
ext4: fix warning in 'ext4_da_release_space'
ext4: fix BUG_ON() when directory entry has invalid rec_len
ext4: update the backup superblock's at the end of the online resize
Pull cifs fixes from Steve French:
"One symlink handling fix and two fixes foir multichannel issues with
iterating channels, including for oplock breaks when leases are
disabled"
* tag '6.1-rc4-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix use-after-free on the link name
cifs: avoid unnecessary iteration of tcp sessions
cifs: always iterate smb sessions using primary channel
Pull `lTracing fixes for 6.1-rc3:
- Fixed NULL pointer dereference in the ring buffer wait-waiters code
for machines that have less CPUs than what nr_cpu_ids returns.
The buffer array is of size nr_cpu_ids, but only the online CPUs get
initialized.
- Fixed use after free call in ftrace_shutdown.
- Fix accounting of if a kprobe is enabled
- Fix NULL pointer dereference on error path of fprobe rethook_alloc().
- Fix unregistering of fprobe_kprobe_handler
- Fix memory leak in kprobe test module
* tag 'trace-v6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: kprobe: Fix memory leak in test_gen_kprobe/kretprobe_cmd()
tracing/fprobe: Fix to check whether fprobe is registered correctly
fprobe: Check rethook_alloc() return in rethook initialization
kprobe: reverse kp->flags when arm_kprobe failed
ftrace: Fix use-after-free for dynamic ftrace_ops
ring-buffer: Check for NULL cpu_buffer in ring_buffer_wake_waiters()
* Fix the pKVM stage-1 walker erronously using the stage-2 accessor
* Correctly convert vcpu->kvm to a hyp pointer when generating
an exception in a nVHE+MTE configuration
* Check that KVM_CAP_DIRTY_LOG_* are valid before enabling them
* Fix SMPRI_EL1/TPIDR2_EL0 trapping on VHE
* Document the boot requirements for FGT when entering the kernel
at EL1
x86:
* Use SRCU to protect zap in __kvm_set_or_clear_apicv_inhibit()
* Make argument order consistent for kvcalloc()
* Userspace API fixes for DEBUGCTL and LBRs
With the new fortify string system, rework the memcpy to avoid this
warning:
memcpy: detected field-spanning write (size 60) of single field "&raw_inode->i_generation" at fs/ext4/fast_commit.c:1551 (size 4)
Cc: stable@kernel.org
Fixes: 54d9469bc5 ("fortify: Add run-time WARN for cross-field memcpy()")
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The return value is wrong in ext4_load_and_init_journal(). The local
variable 'err' need to be initialized before goto out. The original code
in __ext4_fill_super() is fine because it has two return values 'ret'
and 'err' and 'ret' is initialized as -EINVAL. After we factor out
ext4_load_and_init_journal(), this code is broken. So fix it by directly
returning -EINVAL in the error handler path.
Cc: stable@kernel.org
Fixes: 9c1dd22d74 ("ext4: factor out ext4_load_and_init_journal()")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20221025040206.3134773-1-yanaijie@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The rec_len field in the directory entry has to be a multiple of 4. A
corrupted filesystem image can be used to hit a BUG() in
ext4_rec_len_to_disk(), called from make_indexed_dir().
------------[ cut here ]------------
kernel BUG at fs/ext4/ext4.h:2413!
...
RIP: 0010:make_indexed_dir+0x53f/0x5f0
...
Call Trace:
<TASK>
? add_dirent_to_buf+0x1b2/0x200
ext4_add_entry+0x36e/0x480
ext4_add_nondir+0x2b/0xc0
ext4_create+0x163/0x200
path_openat+0x635/0xe90
do_filp_open+0xb4/0x160
? __create_object.isra.0+0x1de/0x3b0
? _raw_spin_unlock+0x12/0x30
do_sys_openat2+0x91/0x150
__x64_sys_open+0x6c/0xa0
do_syscall_64+0x3c/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
The fix simply adds a call to ext4_check_dir_entry() to validate the
directory entry, returning -EFSCORRUPTED if the entry is invalid.
CC: stable@kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216540
Signed-off-by: Luís Henriques <lhenriques@suse.de>
Link: https://lore.kernel.org/r/20221012131330.32456-1-lhenriques@suse.de
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Pull ACPI fix from Rafael Wysocki:
"Add StorageD3Enable quirk for Dell Inspiron 16 5625 (Mario
Limonciello)"
* tag 'acpi-6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: x86: Add another system to quirk list for forcing StorageD3Enable
Pull block fixes from Jens Axboe:
- Fixes for the ublk driver (Ming)
- Fixes for error handling memory leaks (Chen Jun, Chen Zhongjin)
- Explicitly clear the last request in a chain when the plug is
flushed, as it may have already been issued (Al)
* tag 'block-6.1-2022-11-05' of git://git.kernel.dk/linux:
block: blk_add_rq_to_plug(): clear stale 'last' after flush
blk-mq: Fix kmemleak in blk_mq_init_allocated_queue
block: Fix possible memory leak for rq_wb on add_disk failure
ublk_drv: add ublk_queue_cmd() for cleanup
ublk_drv: avoid to touch io_uring cmd in blk_mq io path
ublk_drv: comment on ublk_driver entry of Kconfig
ublk_drv: return flag of UBLK_F_URING_CMD_COMP_IN_TASK in case of module
When we fail to insert into the hashtable with a non-retryable error,
we'll free the object and then goto out_status. If the tracepoint is
enabled, it'll end up accessing the freed object when it tries to
grab the fields out of it.
Set nf to NULL after freeing it to avoid the issue.
Fixes: 243a526301 ("nfsd: rework hashtable handling in nfsd_do_file_acquire")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Jonathan writes:
"2nd set of IIO fixes for 6.1
Another mixed bag of driver fixes.
* atmel,at91-sama5d2
- Drop a 5 degree offset as not needed for production devices.
- Missing iio_trigger_free() in error path.
* bosch,bma400
- Turn power on before trying to read chip ID.
* bosch,bno055
- Avoid uninitialized variable warning (no actual impact)
* meas,ms5611
- Fix multiple instances of driver sharing single prom array.
- Stop forcing SPI speed to max devices supports
* mps,mp2629
- Wrong structure field used to match channel.
- Missing NULL terminator.
* sysfs-trigger
- Fix memory leak in error path.
* tools
- Fix wrong read size when calling with noevents."
* tag 'iio-fixes-for-6.1b' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
tools: iio: iio_generic_buffer: Fix read size
iio: imu: bno055: uninitialized variable bug in bno055_trigger_handler()
iio: adc: at91_adc: fix possible memory leak in at91_adc_allocate_trigger()
iio: adc: mp2629: fix potential array out of bound access
iio: adc: mp2629: fix wrong comparison of channel
iio: pressure: ms5611: changed hardcoded SPI speed to value limited
iio: pressure: ms5611: fixed value compensation bug
iio: accel: bma400: Ensure VDDIO is enable defore reading the chip ID.
iio: adc: at91-sama5d2_adc: get rid of 5 degrees Celsius adjustment
iio: trigger: sysfs: fix possible memory leak in iio_sysfs_trig_init()
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. The UBSAN warning calltrace like below:
UBSAN: shift-out-of-bounds in security/commoncap.c:1252:2
left shift of 1 by 31 places cannot be represented in type 'int'
Call Trace:
<TASK>
dump_stack_lvl+0x7d/0xa5
dump_stack+0x15/0x1b
ubsan_epilogue+0xe/0x4e
__ubsan_handle_shift_out_of_bounds+0x1e7/0x20c
cap_task_prctl+0x561/0x6f0
security_task_prctl+0x5a/0xb0
__x64_sys_prctl+0x61/0x8f0
do_syscall_64+0x58/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
Fixes: e338d263a7 ("Add 64-bit capability support to the kernel")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Acked-by: Andrew G. Morgan <morgan@kernel.org>
Reviewed-by: Serge Hallyn <serge@hallyn.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
xfstests generic/011 reported use-after-free bug as follows:
BUG: KASAN: use-after-free in __d_alloc+0x269/0x859
Read of size 15 at addr ffff8880078933a0 by task dirstress/952
CPU: 1 PID: 952 Comm: dirstress Not tainted 6.1.0-rc3+ #77
Call Trace:
__dump_stack+0x23/0x29
dump_stack_lvl+0x51/0x73
print_address_description+0x67/0x27f
print_report+0x3e/0x5c
kasan_report+0x7b/0xa8
kasan_check_range+0x1b2/0x1c1
memcpy+0x22/0x5d
__d_alloc+0x269/0x859
d_alloc+0x45/0x20c
d_alloc_parallel+0xb2/0x8b2
lookup_open+0x3b8/0x9f9
open_last_lookups+0x63d/0xc26
path_openat+0x11a/0x261
do_filp_open+0xcc/0x168
do_sys_openat2+0x13b/0x3f7
do_sys_open+0x10f/0x146
__se_sys_creat+0x27/0x2e
__x64_sys_creat+0x55/0x6a
do_syscall_64+0x40/0x96
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Allocated by task 952:
kasan_save_stack+0x1f/0x42
kasan_set_track+0x21/0x2a
kasan_save_alloc_info+0x17/0x1d
__kasan_kmalloc+0x7e/0x87
__kmalloc_node_track_caller+0x59/0x155
kstrndup+0x60/0xe6
parse_mf_symlink+0x215/0x30b
check_mf_symlink+0x260/0x36a
cifs_get_inode_info+0x14e1/0x1690
cifs_revalidate_dentry_attr+0x70d/0x964
cifs_revalidate_dentry+0x36/0x62
cifs_d_revalidate+0x162/0x446
lookup_open+0x36f/0x9f9
open_last_lookups+0x63d/0xc26
path_openat+0x11a/0x261
do_filp_open+0xcc/0x168
do_sys_openat2+0x13b/0x3f7
do_sys_open+0x10f/0x146
__se_sys_creat+0x27/0x2e
__x64_sys_creat+0x55/0x6a
do_syscall_64+0x40/0x96
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Freed by task 950:
kasan_save_stack+0x1f/0x42
kasan_set_track+0x21/0x2a
kasan_save_free_info+0x1c/0x34
____kasan_slab_free+0x1c1/0x1d5
__kasan_slab_free+0xe/0x13
__kmem_cache_free+0x29a/0x387
kfree+0xd3/0x10e
cifs_fattr_to_inode+0xb6a/0xc8c
cifs_get_inode_info+0x3cb/0x1690
cifs_revalidate_dentry_attr+0x70d/0x964
cifs_revalidate_dentry+0x36/0x62
cifs_d_revalidate+0x162/0x446
lookup_open+0x36f/0x9f9
open_last_lookups+0x63d/0xc26
path_openat+0x11a/0x261
do_filp_open+0xcc/0x168
do_sys_openat2+0x13b/0x3f7
do_sys_open+0x10f/0x146
__se_sys_creat+0x27/0x2e
__x64_sys_creat+0x55/0x6a
do_syscall_64+0x40/0x96
entry_SYSCALL_64_after_hwframe+0x63/0xcd
When opened a symlink, link name is from 'inode->i_link', but it may be
reset to a new value when revalidate the dentry. If some processes get the
link name on the race scenario, then UAF will happen on link name.
Fix this by implementing 'get_link' interface to duplicate the link name.
Fixes: 76894f3e2f ("cifs: improve symlink handling for smb2+")
Signed-off-by: ChenXiaoSong <chenxiaosong2@huawei.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
In a few places, we do unnecessary iterations of
tcp sessions, even when the server struct is provided.
The change avoids it and uses the server struct provided.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
smb sessions and tcons currently hang off primary channel only.
Secondary channels have the lists as empty. Whenever there's a
need to iterate sessions or tcons, we should use the list in the
corresponding primary channel.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
