Just hook get_link to standard ethtool_op_get_link,
nothing special needed at this point.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fact that the Tx SG flag is fixed to 'on' is only
an oversight. Non-SG mode is also supported. Fix this
by allowing to turn SG off.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the unlikely case of TxBD extensions (i.e. ptp)
the driver tries to unmap the tx_swbd corresponding
to the extension, which is bogus as it has no buffer
attached.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Errors are negative numbers. Using %u shows them as very large positive
numbers such as 4294967277 that don't make sense. Use the %d format
instead, and get a much nicer -19.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Fixes: b48e0bab14 ("net: macb: Migrate to devm clock interface")
Fixes: 93b31f48b3 ("net/macb: unify clock management")
Fixes: 421d9df062 ("net/macb: merge at91_ether driver into macb driver")
Fixes: aead88bd0e ("net: ethernet: macb: Add support for rx_clk")
Fixes: f5473d1d44 ("net: macb: Support clock management for tsu_clk")
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error print within mlx4_flow_steer_promisc_add() should
be a info print.
Fixes: 592e49dda8 ('net/mlx4: Implement promiscuous mode with device managed flow-steering')
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri reported that with a kernel built with CONFIG_FIXED_PHY=y,
CONFIG_NET_DSA=m and CONFIG_NET_DSA_LOOP=m, we would not get to a
functional state where the mock-up driver is registered. Turns out that
we are not descending into drivers/net/dsa/ unconditionally, and we
won't be able to link-in dsa_loop_bdinfo.o which does the actual mock-up
mdio device registration.
Reported-by: Jiri Pirko <jiri@resnulli.us>
Fixes: 40013ff20b ("net: dsa: Fix functional dsa-loop dependency on FIXED_PHY")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Tested-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull virtio updates from Michael Tsirkin:
- enable packed ring support for s390
- several fixes
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio/s390: enable packed ring
virtio/s390: DMA support for virtio-ccw
virtio/s390: use vring_create_virtqueue
virtio/virtio_ring: do some comment fixes
vhost-scsi: remove incorrect memory barrier
tools/virtio/ringtest: Remove bogus definition of BUG_ON()
virtio_ring: Fix potential mem leak in virtqueue_add_indirect_packed
Merge misc updates from Andrew Morton:
- a few misc things and hotfixes
- ocfs2
- almost all of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (139 commits)
kernel/memremap.c: remove the unused device_private_entry_fault() export
mm: delete find_get_entries_tag
mm/huge_memory.c: make __thp_get_unmapped_area static
mm/mprotect.c: fix compilation warning because of unused 'mm' variable
mm/page-writeback: introduce tracepoint for wait_on_page_writeback()
mm/vmscan: simplify trace_reclaim_flags and trace_shrink_flags
mm/Kconfig: update "Memory Model" help text
mm/vmscan.c: don't disable irq again when count pgrefill for memcg
mm: memblock: make keeping memblock memory opt-in rather than opt-out
hugetlbfs: always use address space in inode for resv_map pointer
mm/z3fold.c: support page migration
mm/z3fold.c: add structure for buddy handles
mm/z3fold.c: improve compression by extending search
mm/z3fold.c: introduce helper functions
mm/page_alloc.c: remove unnecessary parameter in rmqueue_pcplist
mm/hmm: add ARCH_HAS_HMM_MIRROR ARCH_HAS_HMM_DEVICE Kconfig
mm/vmscan.c: simplify shrink_inactive_list()
fs/sync.c: sync_file_range(2) may use WB_SYNC_ALL writeback
xen/privcmd-buf.c: convert to use vm_map_pages_zero()
xen/gntdev.c: convert to use vm_map_pages()
...
Pach series "Add FOLL_LONGTERM to GUP fast and use it".
HFI1, qib, and mthca, use get_user_pages_fast() due to its performance
advantages. These pages can be held for a significant time. But
get_user_pages_fast() does not protect against mapping FS DAX pages.
Introduce FOLL_LONGTERM and use this flag in get_user_pages_fast() which
retains the performance while also adding the FS DAX checks. XDP has also
shown interest in using this functionality.[1]
In addition we change get_user_pages() to use the new FOLL_LONGTERM flag
and remove the specialized get_user_pages_longterm call.
[1] https://lkml.org/lkml/2019/3/19/939
"longterm" is a relative thing and at this point is probably a misnomer.
This is really flagging a pin which is going to be given to hardware and
can't move. I've thought of a couple of alternative names but I think we
have to settle on if we are going to use FL_LAYOUT or something else to
solve the "longterm" problem. Then I think we can change the flag to a
better name.
Secondly, it depends on how often you are registering memory. I have
spoken with some RDMA users who consider MR in the performance path...
For the overall application performance. I don't have the numbers as the
tests for HFI1 were done a long time ago. But there was a significant
advantage. Some of which is probably due to the fact that you don't have
to hold mmap_sem.
Finally, architecturally I think it would be good for everyone to use
*_fast. There are patches submitted to the RDMA list which would allow
the use of *_fast (they reworking the use of mmap_sem) and as soon as they
are accepted I'll submit a patch to convert the RDMA core as well. Also
to this point others are looking to use *_fast.
As an aside, Jasons pointed out in my previous submission that *_fast and
*_unlocked look very much the same. I agree and I think further cleanup
will be coming. But I'm focused on getting the final solution for DAX at
the moment.
This patch (of 7):
This patch starts a series which aims to support FOLL_LONGTERM in
get_user_pages_fast(). Some callers who would like to do a longterm (user
controlled pin) of pages with the fast variant of GUP for performance
purposes.
Rather than have a separate get_user_pages_longterm() call, introduce
FOLL_LONGTERM and change the longterm callers to use it.
This patch does not change any functionality. In the short term
"longterm" or user controlled pins are unsafe for Filesystems and FS DAX
in particular has been blocked. However, callers of get_user_pages_fast()
were not "protected".
FOLL_LONGTERM can _only_ be supported with get_user_pages[_fast]() as it
requires vmas to determine if DAX is in use.
NOTE: In merging with the CMA changes we opt to change the
get_user_pages() call in check_and_migrate_cma_pages() to a call of
__get_user_pages_locked() on the newly migrated pages. This makes the
code read better in that we are calling __get_user_pages_locked() on the
pages before and after a potential migration.
As a side affect some of the interfaces are cleaned up but this is not the
primary purpose of the series.
In review[1] it was asked:
<quote>
> This I don't get - if you do lock down long term mappings performance
> of the actual get_user_pages call shouldn't matter to start with.
>
> What do I miss?
A couple of points.
First "longterm" is a relative thing and at this point is probably a
misnomer. This is really flagging a pin which is going to be given to
hardware and can't move. I've thought of a couple of alternative names
but I think we have to settle on if we are going to use FL_LAYOUT or
something else to solve the "longterm" problem. Then I think we can
change the flag to a better name.
Second, It depends on how often you are registering memory. I have spoken
with some RDMA users who consider MR in the performance path... For the
overall application performance. I don't have the numbers as the tests
for HFI1 were done a long time ago. But there was a significant
advantage. Some of which is probably due to the fact that you don't have
to hold mmap_sem.
Finally, architecturally I think it would be good for everyone to use
*_fast. There are patches submitted to the RDMA list which would allow
the use of *_fast (they reworking the use of mmap_sem) and as soon as they
are accepted I'll submit a patch to convert the RDMA core as well. Also
to this point others are looking to use *_fast.
As an asside, Jasons pointed out in my previous submission that *_fast and
*_unlocked look very much the same. I agree and I think further cleanup
will be coming. But I'm focused on getting the final solution for DAX at
the moment.
</quote>
[1] https://lore.kernel.org/lkml/20190220180255.GA12020@iweiny-DESK2.sc.intel.com/T/#md6abad2569f3bf6c1f03686c8097ab6563e94965
[ira.weiny@intel.com: v3]
Link: http://lkml.kernel.org/r/20190328084422.29911-2-ira.weiny@intel.com
Link: http://lkml.kernel.org/r/20190328084422.29911-2-ira.weiny@intel.com
Link: http://lkml.kernel.org/r/20190317183438.2057-2-ira.weiny@intel.com
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Rich Felker <dalias@libc.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 MDS mitigations from Thomas Gleixner:
"Microarchitectural Data Sampling (MDS) is a hardware vulnerability
which allows unprivileged speculative access to data which is
available in various CPU internal buffers. This new set of misfeatures
has the following CVEs assigned:
CVE-2018-12126 MSBDS Microarchitectural Store Buffer Data Sampling
CVE-2018-12130 MFBDS Microarchitectural Fill Buffer Data Sampling
CVE-2018-12127 MLPDS Microarchitectural Load Port Data Sampling
CVE-2019-11091 MDSUM Microarchitectural Data Sampling Uncacheable Memory
MDS attacks target microarchitectural buffers which speculatively
forward data under certain conditions. Disclosure gadgets can expose
this data via cache side channels.
Contrary to other speculation based vulnerabilities the MDS
vulnerability does not allow the attacker to control the memory target
address. As a consequence the attacks are purely sampling based, but
as demonstrated with the TLBleed attack samples can be postprocessed
successfully.
The mitigation is to flush the microarchitectural buffers on return to
user space and before entering a VM. It's bolted on the VERW
instruction and requires a microcode update. As some of the attacks
exploit data structures shared between hyperthreads, full protection
requires to disable hyperthreading. The kernel does not do that by
default to avoid breaking unattended updates.
The mitigation set comes with documentation for administrators and a
deeper technical view"
* 'x86-mds-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
x86/speculation/mds: Fix documentation typo
Documentation: Correct the possible MDS sysfs values
x86/mds: Add MDSUM variant to the MDS documentation
x86/speculation/mds: Add 'mitigations=' support for MDS
x86/speculation/mds: Print SMT vulnerable on MSBDS with mitigations off
x86/speculation/mds: Fix comment
x86/speculation/mds: Add SMT warning message
x86/speculation: Move arch_smt_update() call to after mitigation decisions
x86/speculation/mds: Add mds=full,nosmt cmdline option
Documentation: Add MDS vulnerability documentation
Documentation: Move L1TF to separate directory
x86/speculation/mds: Add mitigation mode VMWERV
x86/speculation/mds: Add sysfs reporting for MDS
x86/speculation/mds: Add mitigation control for MDS
x86/speculation/mds: Conditionally clear CPU buffers on idle entry
x86/kvm/vmx: Add MDS protection when L1D Flush is not active
x86/speculation/mds: Clear CPU buffers on exit to user
x86/speculation/mds: Add mds_clear_cpu_buffers()
x86/kvm: Expose X86_FEATURE_MD_CLEAR to guests
x86/speculation/mds: Add BUG_MSBDS_ONLY
...
Add fwnode support to the lm3630a driver and optionally allow
configuring the label, default brightness level, and maximum brightness
level. The two outputs can be controlled by bank A and B independently
or bank A can control both outputs.
If the platform data was not configured, then the driver defaults to
enabling both banks. This patch changes the default value to disable
both banks before parsing the firmware node so that just a single bank
can be enabled if desired. There are no in-tree users of this driver.
Driver was tested on a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
lm3630a_bank_a_update_status() and lm3630a_bank_b_update_status()
both return the brightness value if the brightness was successfully
updated. Writing to these attributes via sysfs would cause a 'Bad
address' error to be returned. These functions should return 0 on
success, so let's change it to correct that error.
Fixes: 28e64a68a2 ("backlight: lm3630: apply chip revision")
Signed-off-by: Brian Masney <masneyb@onstation.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Support Touchpad MCU as a special of CrOS EC devices. The current
Touchpad MCU is used on Eve Chromebook and used the same protocol as
other CrOS EC devices.
When a MCU has touchpad support (aka EC_FEATURE_TOUCHPAD), it is
instantiated as a special CrOS EC device with device name 'cros_tp'. So
regardless of the probing order between the actual cros_ec and cros_tp,
the userspace and other kernel drivers should not confuse them.
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Support Fingerprint MCU as a special of CrOS EC devices. The current FP
MCU uses the same EC SPI protocol v3 as other CrOS EC devices on a SPI
bus.
When a MCU has fingerprint support (aka EC_FEATURE_FINGERPRINT), it is
instantiated as a special CrOS EC device with device name 'cros_fp'. So
regardless of the probing order between the actual cros_ec and cros_fp,
the userspace and other kernel drivers should not confuse them.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since there are more IOT2040 variants with identical hardware but
different asset tags, the asset tag matching should be adjusted to
support them.
For the board name "SIMATIC IOT2000", currently there are 2 types of
hardware, IOT2020 and IOT2040. Both are identical regarding the
intel_quark_i2c_gpio. In the future there will be no other devices with
the "SIMATIC IOT2000" DMI board name but different hardware. So remove
the asset tag matching from this driver.
Signed-off-by: Su Bao Cheng <baocheng.su@siemens.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MODULE_DEVICE_TABLE(of, <of_match_table> should be called to complete DT
OF mathing mechanism and register it.
Before this patch:
modinfo drivers/mfd/tps65912-spi.ko | grep alias
alias: spi:tps65912
After this patch:
modinfo drivers/mfd/tps65912-spi.ko | grep alias
alias: of:N*T*Cti,tps65912C*
alias: of:N*T*Cti,tps65912
alias: spi:tps65912
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP803 has a VBUS power input. Its functionality is the same as the
one found in the AXP813. Now that the axp20x_usb_power driver supports
this variant, we can add an mfd cell for it to use it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When CONFIG_OF is disabled, we get a harmless warning about an
unused variable:
drivers/mfd/sun6i-prcm.c: In function 'sun6i_prcm_probe':
drivers/mfd/sun6i-prcm.c:151:22: error: unused variable 'np' [-Werror=unused-variable]
Remove the variable and open-code the value in the only place
it is used, so it can get left out as well without CONFIG_OF.
Fixes: a05a2e7998 ("mfd: sun6i-prcm: Allow to compile with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support in code for the new forms of the host sleep event.
Detects the presence of this version of the command at runtime,
and use whichever form the EC supports. At this time, always
request the default timeout, and only report the failing response
via a WARN_ONCE(). Future versions could accept the sleep parameter
from outside the driver, and return the response information to
usermode or elsewhere.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Rajat Jain <rajatja@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the cros-usbpd-logger driver for logging event data for the USB PD
charger available in the Embedded Controller on ChromeOS systems. The
logging feature is logically separate functionality from charge manager,
hence is instantiated as a different driver.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenetr Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP223 can be used both using the RSB proprietary bus, or a more
traditional I2C bus. The RSB is a faster bus and provides more features
(like some integrity checks on the messages), so it's usually preferrable
to use it, but since it's proprietary, when we want to use the PMIC in a
multi-master setup, the i2c might make sense as well.
Let's add that possibility.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
