There is a race and a buffer overflow corrupting a kernel memory while
reading an EFI variable with a size more than 1024 bytes via the older
sysfs method. This happens because accessing struct efi_variable in
efivar_{attr,size,data}_read() and friends is not protected from
a concurrent access leading to a kernel memory corruption and, at best,
to a crash. The race scenario is the following:
CPU0: CPU1:
efivar_attr_read()
var->DataSize = 1024;
efivar_entry_get(... &var->DataSize)
down_interruptible(&efivars_lock)
efivar_attr_read() // same EFI var
var->DataSize = 1024;
efivar_entry_get(... &var->DataSize)
down_interruptible(&efivars_lock)
virt_efi_get_variable()
// returns EFI_BUFFER_TOO_SMALL but
// var->DataSize is set to a real
// var size more than 1024 bytes
up(&efivars_lock)
virt_efi_get_variable()
// called with var->DataSize set
// to a real var size, returns
// successfully and overwrites
// a 1024-bytes kernel buffer
up(&efivars_lock)
This can be reproduced by concurrent reading of an EFI variable which size
is more than 1024 bytes:
ts# for cpu in $(seq 0 $(nproc --ignore=1)); do ( taskset -c $cpu \
cat /sys/firmware/efi/vars/KEKDefault*/size & ) ; done
Fix this by using a local variable for a var's data buffer size so it
does not get overwritten.
Fixes: e14ab23dde ("efivars: efivar_entry API")
Reported-by: Bob Sanders <bob.sanders@hpe.com> and the LTP testsuite
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200305084041.24053-2-vdronov@redhat.com
Link: https://lore.kernel.org/r/20200308080859.21568-24-ardb@kernel.org
After FS_IOC_REMOVE_ENCRYPTION_KEY removes a key, it syncs the
filesystem and tries to get and put all inodes that were unlocked by the
key so that unused inodes get evicted via fscrypt_drop_inode().
Normally, the inodes are all clean due to the sync.
However, after the filesystem is sync'ed, userspace can modify and close
one of the files. (Userspace is *supposed* to close the files before
removing the key. But it doesn't always happen, and the kernel can't
assume it.) This causes the inode to be dirtied and have i_count == 0.
Then, fscrypt_drop_inode() failed to consider this case and indicated
that the inode can be dropped, causing the write to be lost.
On f2fs, other problems such as a filesystem freeze could occur due to
the inode being freed while still on f2fs's dirty inode list.
Fix this bug by making fscrypt_drop_inode() only drop clean inodes.
I've written an xfstest which detects this bug on ext4, f2fs, and ubifs.
Fixes: b1c0ec3599 ("fscrypt: add FS_IOC_REMOVE_ENCRYPTION_KEY ioctl")
Cc: <stable@vger.kernel.org> # v5.4+
Link: https://lore.kernel.org/r/20200305084138.653498-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Pull rdma fixes from Jason Gunthorpe:
"Nothing particularly exciting, some small ODP regressions from the mmu
notifier rework, another bunch of syzkaller fixes, and a bug fix for a
botched syzkaller fix in the first rc pull request.
- Fix busted syzkaller fix in 'get_new_pps' - this turned out to
crash on certain HW configurations
- Bug fixes for various missed things in error unwinds
- Add a missing rcu_read_lock annotation in hfi/qib
- Fix two ODP related regressions from the recent mmu notifier
changes
- Several more syzkaller bugs in siw, RDMA netlink, verbs and iwcm
- Revert an old patch in CMA as it is now shown to not be allocating
port numbers properly"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/iwcm: Fix iwcm work deallocation
RDMA/siw: Fix failure handling during device creation
RDMA/nldev: Fix crash when set a QP to a new counter but QPN is missing
RDMA/odp: Ensure the mm is still alive before creating an implicit child
RDMA/core: Fix protection fault in ib_mr_pool_destroy
IB/mlx5: Fix implicit ODP race
IB/hfi1, qib: Ensure RCU is locked when accessing list
RDMA/core: Fix pkey and port assignment in get_new_pps
RMDA/cm: Fix missing ib_cm_destroy_id() in ib_cm_insert_listen()
RDMA/rw: Fix error flow during RDMA context initialization
RDMA/core: Fix use of logical OR in get_new_pps
Revert "RDMA/cma: Simplify rdma_resolve_addr() error flow"
Pull io_uring fixes from Jens Axboe:
"Here are a few io_uring fixes that should go into this release. This
contains:
- Removal of (now) unused io_wq_flush() and associated flag (Pavel)
- Fix cancelation lockup with linked timeouts (Pavel)
- Fix for potential use-after-free when freeing percpu ref for fixed
file sets
- io-wq cancelation fixups (Pavel)"
* tag 'io_uring-5.6-2020-03-07' of git://git.kernel.dk/linux-block:
io_uring: fix lockup with timeouts
io_uring: free fixed_file_data after RCU grace period
io-wq: remove io_wq_flush and IO_WQ_WORK_INTERNAL
io-wq: fix IO_WQ_WORK_NO_CANCEL cancellation
Pull block fixes from Jens Axboe:
"Here are a few fixes that should go into this release. This contains:
- Revert of a bad bcache patch from this merge window
- Removed unused function (Daniel)
- Fixup for the blktrace fix from Jan from this release (Cengiz)
- Fix of deeper level bfqq overwrite in BFQ (Carlo)"
* tag 'block-5.6-2020-03-07' of git://git.kernel.dk/linux-block:
block, bfq: fix overwrite of bfq_group pointer in bfq_find_set_group()
blktrace: fix dereference after null check
Revert "bcache: ignore pending signals when creating gc and allocator thread"
block: Remove used kblockd_schedule_work_on()
Pull media fixes from Mauro Carvalho Chehab:
- a fix for the media controller links in both hantro driver and in
v4l2-mem2mem core
- some fixes for the pulse8-cec driver
- vicodec: handle alpha channel for RGB32 formats, as it may be used
- mc-entity.c: fix handling of pad flags
* tag 'media/v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: hantro: Fix broken media controller links
media: mc-entity.c: use & to check pad flags, not ==
media: v4l2-mem2mem.c: fix broken links
media: vicodec: process all 4 components for RGB32 formats
media: pulse8-cec: close serio in disconnect, not adap_free
media: pulse8-cec: INIT_DELAYED_WORK was called too late
There is a recipe to deadlock the kernel: submit a timeout sqe with a
linked_timeout (e.g. test_single_link_timeout_ception() from liburing),
and SIGKILL the process.
Then, io_kill_timeouts() takes @ctx->completion_lock, but the timeout
isn't flagged with REQ_F_COMP_LOCKED, and will try to double grab it
during io_put_free() to cancel the linked timeout. Probably, the same
can happen with another io_kill_timeout() call site, that is
io_commit_cqring().
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull s390 fixes from Vasily Gorbik:
- Fix panic in gup_fast on large pud by providing an implementation of
pud_write. This has been overlooked during migration to common gup
code.
- Fix unexpected write combining on PCI stores.
* tag 's390-5.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: Fix unexpected write combine on resource
s390/mm: fix panic in gup_fast on large pud
Pull powerpc fixes from Michael Ellerman:
"Some more powerpc fixes for 5.6:
- One fix for a recent regression to our breakpoint/watchpoint code.
- Another fix for our KUAP support, this time a missing annotation in
a rarely used path in signal handling.
- A fix for our handling of a CPU feature that effects the PMU, when
booting guests in some configurations.
- A minor fix to our linker script to explicitly include the .BTF
section.
Thanks to: Christophe Leroy, Desnes A. Nunes do Rosario, Leonardo
Bras, Naveen N. Rao, Ravi Bangoria, Stefan Berger"
* tag 'powerpc-5.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fix missing KUAP disable in flush_coherent_icache()
powerpc: fix hardware PMU exception bug on PowerVM compatibility mode systems
powerpc: Include .BTF section
powerpc/watchpoint: Don't call dar_within_range() for Book3S
Pull xen fixes from Juergen Gross:
"Four fixes and a small cleanup patch:
- two fixes by Dongli Zhang fixing races in the xenbus driver
- two fixes by me fixing issues introduced in 5.6
- a small cleanup by Gustavo Silva replacing a zero-length array with
a flexible-array"
* tag 'for-linus-5.6b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/blkfront: fix ring info addressing
xen/xenbus: fix locking
xenbus: req->err should be updated before req->state
xenbus: req->body should be updated before req->state
xen: Replace zero-length array with flexible-array member
Pull thread fixes from Christian Brauner:
"Here are a few hopefully uncontroversial fixes:
- Use RCU_INIT_POINTER() when initializing rcu protected members in
task_struct to fix sparse warnings.
- Add pidfd_fdinfo_test binary to .gitignore file"
* tag 'for-linus-2020-03-07' of gitolite.kernel.org:pub/scm/linux/kernel/git/brauner/linux:
selftests: pidfd: Add pidfd_fdinfo_test in .gitignore
exit: Fix Sparse errors and warnings
fork: Use RCU_INIT_POINTER() instead of rcu_access_pointer()
Pull sound fixes from Takashi Iwai:
"The regular "bump-in-the-middle" updates, containing mostly ASoC-
related fixes at this time. All changes are reasonably small.
A few entries are for ASoC and ALSA core parts (DAPM, PCM, topology)
for followups of the recent changes and potential buffer overflow by
snprintf(), while the rest are (both new and old) device-specific
fixes for Intel, meson, tas2562, rt1015, as well as the usual HD-audio
quirks"
* tag 'sound-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (25 commits)
ALSA: sgio2audio: Remove usage of dropped hw_params/hw_free functions
ALSA: hda/realtek - Enable the headset of ASUS B9450FA with ALC294
ALSA: hda/realtek - Fix silent output on Gigabyte X570 Aorus Master
ALSA: hda/realtek - Add Headset Button supported for ThinkPad X1
ALSA: hda/realtek - Add Headset Mic supported
ASoC: wm8741: Fix typo in Kconfig prompt
ASoC: stm32: sai: manage rebind issue
ASoC: SOF: Fix snd_sof_ipc_stream_posn()
ASoC: rt1015: modify pre-divider for sysclk
ASoC: rt1015: add operation callback function for rt1015_dai[]
ASoC: soc-component: tidyup snd_soc_pcm_component_sync_stop()
ASoC: dapm: Correct DAPM handling of active widgets during shutdown
ASoC: tas2562: Fix sample rate error message
ASoC: Intel: Skylake: Fix available clock counter incrementation
ASoC: soc-pcm/soc-compress: don't use snd_soc_dapm_stream_stop()
ASoC: meson: g12a: add tohdmitx reset
ASoC: pcm512x: Fix unbalanced regulator enable call in probe error path
ASoC: soc-core: fix for_rtd_codec_dai_rollback() macro
ASoC: topology: Fix memleak in soc_tplg_manifest_load()
ASoC: topology: Fix memleak in soc_tplg_link_elems_load()
...
There is a ACT8600 on the CI20 board and the bindings of the
ACT8865 driver have changed without updating the CI20 device
tree. Therefore the PMU can not be probed successfully and
is running in power-on reset state.
Fix DT to match the latest act8865-regulator bindings.
Fixes: 73f2b94047 ("MIPS: CI20: DTS: Add I2C nodes")
Cc: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
rhashtable_lookup_get_insert_key doesn't have a parameter `data`. It
does have a parameter `key`, however.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
ASoC: Fixes for v5.6
More fixes that have arrived since the merge window, spread out all
over. There's a few things like the operation callback addition for
rt1015 and the meson reset addition which add small new bits of
functionality to fix non-working systems, they're all very small and for
parts of newly added functionality.
These are a couple of read locks that should be write locks.
Fixes: fbb39807e9 ("ionic: support sr-iov operations")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur says:
====================
QorIQ DPAA FMan erratum A050385 workaround
Changes in v2:
- added CONFIG_DPAA_ERRATUM_A050385
- removed unnecessary parenthesis
- changed alignment defines to use only decimal values
The patch set implements the workaround for FMan erratum A050385:
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak; thus stopping further packet processing.
To reproduce this issue when the workaround is not applied, one
needs to ensure the FMan DMA transaction queue is already full
when a transaction split occurs so the system must be under high
traffic load (i.e. multiple ports at line rate). After the errata
occurs, the traffic stops. The only SoC impacted by this is the
LS1043A, the other ARM DPAA 1 SoC or the PPC DPAA 1 SoCs do not
have this erratum.
The FMAN internal queue can overflow when FMAN splits single
read or write transactions into multiple smaller transactions
such that more than 17 AXI transactions are in flight from FMAN
to interconnect. When the FMAN internal queue overflows, it can
stall further packet processing. The issue can occur with any one
of the following three conditions:
1. FMAN AXI transaction crosses 4K address boundary (Errata
A010022)
2. FMAN DMA address for an AXI transaction is not 16 byte
aligned, i.e. the last 4 bits of an address are non-zero
3. Scatter Gather (SG) frames have more than one SG buffer in
the SG list and any one of the buffers, except the last
buffer in the SG list has data size that is not a multiple
of 16 bytes, i.e., other than 16, 32, 48, 64, etc.
With any one of the above three conditions present, there is
likelihood of stalled FMAN packet processing, especially under
stress with multiple ports injecting line-rate traffic.
To avoid situations that stall FMAN packet processing, all of the
above three conditions must be avoided; therefore, configure the
system with the following rules:
1. Frame buffers must not span a 4KB address boundary, unless
the frame start address is 256 byte aligned
2. All FMAN DMA start addresses (for example, BMAN buffer
address, FD[address] + FD[offset]) are 16B aligned
3. SG table and buffer addresses are 16B aligned and the size
of SG buffers are multiple of 16 bytes, except for the last
SG buffer that can be of any size.
Additional workaround notes:
- Address alignment of 64 bytes is recommended for maximally
efficient system bus transactions (although 16 byte alignment is
sufficient to avoid the stall condition)
- To support frame sizes that are larger than 4K bytes, there are
two options:
1. Large single buffer frames that span a 4KB page boundary can
be converted into SG frames to avoid transaction splits at
the 4KB boundary,
2. Align the large single buffer to 256B address boundaries,
ensure that the frame address plus offset is 256B aligned.
- If software generated SG frames have buffers that are unaligned
and with random non-multiple of 16 byte lengths, before
transmitting such frames via FMAN, frames will need to be copied
into a new single buffer or multiple buffer SG frame that is
compliant with the three rules listed above.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Align buffers, data start, SG fragment length to avoid DMA splits.
These changes prevent the A050385 erratum to manifest itself:
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak; thus stopping further packet processing.
The FMAN internal queue can overflow when FMAN splits single
read or write transactions into multiple smaller transactions
such that more than 17 AXI transactions are in flight from FMAN
to interconnect. When the FMAN internal queue overflows, it can
stall further packet processing. The issue can occur with any one
of the following three conditions:
1. FMAN AXI transaction crosses 4K address boundary (Errata
A010022)
2. FMAN DMA address for an AXI transaction is not 16 byte
aligned, i.e. the last 4 bits of an address are non-zero
3. Scatter Gather (SG) frames have more than one SG buffer in
the SG list and any one of the buffers, except the last
buffer in the SG list has data size that is not a multiple
of 16 bytes, i.e., other than 16, 32, 48, 64, etc.
With any one of the above three conditions present, there is
likelihood of stalled FMAN packet processing, especially under
stress with multiple ports injecting line-rate traffic.
To avoid situations that stall FMAN packet processing, all of the
above three conditions must be avoided; therefore, configure the
system with the following rules:
1. Frame buffers must not span a 4KB address boundary, unless
the frame start address is 256 byte aligned
2. All FMAN DMA start addresses (for example, BMAN buffer
address, FD[address] + FD[offset]) are 16B aligned
3. SG table and buffer addresses are 16B aligned and the size
of SG buffers are multiple of 16 bytes, except for the last
SG buffer that can be of any size.
Additional workaround notes:
- Address alignment of 64 bytes is recommended for maximally
efficient system bus transactions (although 16 byte alignment is
sufficient to avoid the stall condition)
- To support frame sizes that are larger than 4K bytes, there are
two options:
1. Large single buffer frames that span a 4KB page boundary can
be converted into SG frames to avoid transaction splits at
the 4KB boundary,
2. Align the large single buffer to 256B address boundaries,
ensure that the frame address plus offset is 256B aligned.
- If software generated SG frames have buffers that are unaligned
and with random non-multiple of 16 byte lengths, before
transmitting such frames via FMAN, frames will need to be copied
into a new single buffer or multiple buffer SG frame that is
compliant with the three rules listed above.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LS1043A SoC is affected by the A050385 erratum stating that
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak thus stopping further packet processing.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak; thus stopping further packet processing.
The FMAN internal queue can overflow when FMAN splits single
read or write transactions into multiple smaller transactions
such that more than 17 AXI transactions are in flight from FMAN
to interconnect. When the FMAN internal queue overflows, it can
stall further packet processing. The issue can occur with any one
of the following three conditions:
1. FMAN AXI transaction crosses 4K address boundary (Errata
A010022)
2. FMAN DMA address for an AXI transaction is not 16 byte
aligned, i.e. the last 4 bits of an address are non-zero
3. Scatter Gather (SG) frames have more than one SG buffer in
the SG list and any one of the buffers, except the last
buffer in the SG list has data size that is not a multiple
of 16 bytes, i.e., other than 16, 32, 48, 64, etc.
With any one of the above three conditions present, there is
likelihood of stalled FMAN packet processing, especially under
stress with multiple ports injecting line-rate traffic.
To avoid situations that stall FMAN packet processing, all of the
above three conditions must be avoided; therefore, configure the
system with the following rules:
1. Frame buffers must not span a 4KB address boundary, unless
the frame start address is 256 byte aligned
2. All FMAN DMA start addresses (for example, BMAN buffer
address, FD[address] + FD[offset]) are 16B aligned
3. SG table and buffer addresses are 16B aligned and the size
of SG buffers are multiple of 16 bytes, except for the last
SG buffer that can be of any size.
Additional workaround notes:
- Address alignment of 64 bytes is recommended for maximally
efficient system bus transactions (although 16 byte alignment is
sufficient to avoid the stall condition)
- To support frame sizes that are larger than 4K bytes, there are
two options:
1. Large single buffer frames that span a 4KB page boundary can
be converted into SG frames to avoid transaction splits at
the 4KB boundary,
2. Align the large single buffer to 256B address boundaries,
ensure that the frame address plus offset is 256B aligned.
- If software generated SG frames have buffers that are unaligned
and with random non-multiple of 16 byte lengths, before
transmitting such frames via FMAN, frames will need to be copied
into a new single buffer or multiple buffer SG frame that is
compliant with the three rules listed above.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Patches to bump position index from sysctl seq_next,
from Vasilin Averin.
2) Release flowtable hook from error path, from Florian Westphal.
3) Patches to add missing netlink attribute validation,
from Jakub Kicinski.
4) Missing NFTA_CHAIN_FLAGS in nf_tables_fill_chain_info().
5) Infinite loop in module autoload if extension is not available,
from Florian Westphal.
6) Missing module ownership in inet/nat chain type definition.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull kselftest update from Shuah Khan:
"This consists of a cleanup patch to undo changes to global .gitignore
that added selftests/lkdtm objects and add them to a local
selftests/lkdtm/.gitignore.
Summary of Linus's comments on local vs. global gitignore scope:
- Keep local gitignore patterns in local files.
- Put only global gitignore patterns in the top-level gitignore file.
Local scope keeps things much better separated. It also incidentally
means that if a directory gets renamed, the gitignore file continues
to work unless in the case of renaming the actual files themselves
that are named in the gitignore"
* tag 'linux-kselftest-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftest/lkdtm: Use local .gitignore
Pull RISC-V fixes from Palmer Dabbelt:
"This contains a handful of fixes that I would like to target for 5.6:
- A pair of fixes to module loading, which we hope solve the last of
the issues with module text being loaded too sparsely for our call
relocations.
- A Kconfig fix that disallows selecting memory models not supported
by NOMMU.
- A series of Kconfig updates to ease selecting the drivers necessary
to run on QEMU's virt platform.
- DTS updates for SiFive's HiFive Unleashed.
- A fix to our seccomp support that avoids mangling restartable
syscalls"
* tag 'riscv-for-linus-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: fix seccomp reject syscall code path
riscv: dts: Add GPIO reboot method to HiFive Unleashed DTS file
RISC-V: Select Goldfish RTC driver for QEMU virt machine
RISC-V: Select SYSCON Reboot and Poweroff for QEMU virt machine
RISC-V: Enable QEMU virt machine support in defconfigs
RISC-V: Add kconfig option for QEMU virt machine
riscv: Fix range looking for kernel image memblock
riscv: Force flat memory model with no-mmu
riscv: Change code model of module to medany to improve data accessing
riscv: avoid the PIC offset of static percpu data in module beyond 2G limits
Pull devicetree fixes from Rob Herring:
"Another batch of DT fixes. I think this should be the last of it, but
sending pull requests seems to cause people to send more fixes.
Summary:
- Fixes for warnings introduced by hierarchical PSCI binding changes
- Fixes for broken doc references due to DT schema conversions
- Several grammar and typo fixes
- Fix a bunch of dtc warnings in examples"
* tag 'devicetree-fixes-for-5.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: arm: Fixup the DT bindings for hierarchical PSCI states
dt-bindings: power: Extend nodename pattern for power-domain providers
MAINTAINERS: update ALLWINNER CPUFREQ DRIVER entry
dt-bindings: bus: Drop empty compatible string in example
dt-bindings: power: Convert domain-idle-states bindings to json-schema
dt-bindings: arm: Fix cpu compatibles in the hierarchical example for PSCI
dt-bindings: arm: Correct links to idle states definitions
dt-bindings: mfd: Fix typo in file name of twl-familly.txt
dt-bindings: mfd: tps65910: Improve grammar
dt-bindings: mfd: zii,rave-sp: Fix a typo ("onborad")
dt-bindings: arm: fsl: fix APF6Dev compatible
dt-bindings: Fix dtc warnings in examples
docs: dt: fix several broken doc references
docs: dt: fix several broken references due to renames
MAINTAINERS: clean up PCIE DRIVER FOR CAVIUM THUNDERX
Pull vgacon fix from Daniel Vetter:
"One vgacon input check for stable"
* tag 'drm-fixes-2020-03-06-1' of git://anongit.freedesktop.org/drm/drm:
vgacon: Fix a UAF in vgacon_invert_region
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Pull btrfs fix from David Sterba:
"One fixup for DIO when in use with the new checksums, a missed case
where the checksum size was still assuming u32"
* tag 'for-5.6-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix RAID direct I/O reads with alternate csums
Pull file locking fixes from Jeff Layton:
"Just a couple of late-breaking patches for the file locking code. The
second patch (from yangerkun) fixes a rather nasty looking potential
use-after-free that should go to stable.
The other patch could technically wait for 5.7, but it's fairly
innocuous so I figured we might as well take it"
* tag 'filelock-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
locks: fix a potential use-after-free problem when wakeup a waiter
fcntl: Distribute switch variables for initialization
Pull spi fixes from Mark Brown:
"A selection of small fixes, mostly for drivers, that have arrived
since the merge window. None of them are earth shattering in
themselves but all useful for affected systems"
* tag 'spi-fix-v5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi_register_controller(): free bus id on error paths
spi: bcm63xx-hsspi: Really keep pll clk enabled
spi: atmel-quadspi: fix possible MMIO window size overrun
spi/zynqmp: remove entry that causes a cs glitch
spi: pxa2xx: Add CS control clock quirk
spi: spidev: Fix CS polarity if GPIO descriptors are used
spi: qup: call spi_qup_pm_resume_runtime before suspending
spi: spi-omap2-mcspi: Support probe deferral for DMA channels
spi: spi-omap2-mcspi: Handle DMA size restriction on AM65x
Pull regulator fixes from Mark Brown:
"A couple of small fixes, one for a minor issue in the stm32-vrefbuf
driver and a documentation fix in the Qualcomm code"
* tag 'regulator-fix-v5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: stm32-vrefbuf: fix a possible overshoot when re-enabling
regulator: qcom_spmi: Fix docs for PM8004
Pull hwmon fixes from Guenter Roeck:
"Fix an error return in the adt7462 driver, bad voltage limits reported
by the xdpe12284 driver, and a broken documentation reference in the
adm1177 driver documentation"
* tag 'hwmon-for-v5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (adt7462) Fix an error return in ADT7462_REG_VOLT()
hwmon: (pmbus/xdpe12284) Add callback for vout limits conversion
docs: adm1177: fix a broken reference
Pull arm64 fixes from Will Deacon:
"Here are another three arm64 fixes for 5.6, all pretty minor. Main
thing is fixing a silly bug in the fsl_imx8_ddr PMU driver where we
would zero the counters when disabling them.
- Fix misreporting of ASID limit when KPTI is enabled
- Fix busted NULL pointer checks for GICC structure in ACPI PMU code
- Avoid nobbling the "fsl_imx8_ddr" PMU counters when disabling them"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: context: Fix ASID limit in boot messages
drivers/perf: arm_pmu_acpi: Fix incorrect checking of gicc pointer
drivers/perf: fsl_imx8_ddr: Correct the CLEAR bit definition
When I tried to compile tools/perf from the top directory with the -C
option, the O= option didn't work correctly if I passed a relative path:
$ make O=BUILD -C tools/perf/
make: Entering directory '/home/mhiramat/ksrc/linux/tools/perf'
BUILD: Doing 'make -j8' parallel build
../scripts/Makefile.include:4: *** O=/home/mhiramat/ksrc/linux/tools/perf/BUILD does not exist. Stop.
make: *** [Makefile:70: all] Error 2
make: Leaving directory '/home/mhiramat/ksrc/linux/tools/perf'
The O= directory existence check failed because the check script ran in
the build target directory instead of the directory where I ran the make
command.
To fix that, once change directory to $(PWD) and check O= directory,
since the PWD is set to where the make command runs.
Fixes: c883122acc ("perf tools: Let O= makes handle relative paths")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sasha Levin <sashal@kernel.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/158351957799.3363.15269768530697526765.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When syzkaller tests, there is a UAF:
BUG: KASan: use after free in vgacon_invert_region+0x9d/0x110 at addr
ffff880000100000
Read of size 2 by task syz-executor.1/16489
page:ffffea0000004000 count:0 mapcount:-127 mapping: (null)
index:0x0
page flags: 0xfffff00000000()
page dumped because: kasan: bad access detected
CPU: 1 PID: 16489 Comm: syz-executor.1 Not tainted
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014
Call Trace:
[<ffffffffb119f309>] dump_stack+0x1e/0x20
[<ffffffffb04af957>] kasan_report+0x577/0x950
[<ffffffffb04ae652>] __asan_load2+0x62/0x80
[<ffffffffb090f26d>] vgacon_invert_region+0x9d/0x110
[<ffffffffb0a39d95>] invert_screen+0xe5/0x470
[<ffffffffb0a21dcb>] set_selection+0x44b/0x12f0
[<ffffffffb0a3bfae>] tioclinux+0xee/0x490
[<ffffffffb0a1d114>] vt_ioctl+0xff4/0x2670
[<ffffffffb0a0089a>] tty_ioctl+0x46a/0x1a10
[<ffffffffb052db3d>] do_vfs_ioctl+0x5bd/0xc40
[<ffffffffb052e2f2>] SyS_ioctl+0x132/0x170
[<ffffffffb11c9b1b>] system_call_fastpath+0x22/0x27
Memory state around the buggy address:
ffff8800000fff00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00
ffff8800000fff80: 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00
>ffff880000100000: ff ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff
It can be reproduce in the linux mainline by the program:
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <fcntl.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <sys/ioctl.h>
#include <linux/vt.h>
struct tiocl_selection {
unsigned short xs; /* X start */
unsigned short ys; /* Y start */
unsigned short xe; /* X end */
unsigned short ye; /* Y end */
unsigned short sel_mode; /* selection mode */
};
#define TIOCL_SETSEL 2
struct tiocl {
unsigned char type;
unsigned char pad;
struct tiocl_selection sel;
};
int main()
{
int fd = 0;
const char *dev = "/dev/char/4:1";
struct vt_consize v = {0};
struct tiocl tioc = {0};
fd = open(dev, O_RDWR, 0);
v.v_rows = 3346;
ioctl(fd, VT_RESIZEX, &v);
tioc.type = TIOCL_SETSEL;
ioctl(fd, TIOCLINUX, &tioc);
return 0;
}
When resize the screen, update the 'vc->vc_size_row' to the new_row_size,
but when 'set_origin' in 'vgacon_set_origin', vgacon use 'vga_vram_base'
for 'vc_origin' and 'vc_visible_origin', not 'vc_screenbuf'. It maybe
smaller than 'vc_screenbuf'. When TIOCLINUX, use the new_row_size to calc
the offset, it maybe larger than the vga_vram_size in vgacon driver, then
bad access.
Also, if set an larger screenbuf firstly, then set an more larger
screenbuf, when copy old_origin to new_origin, a bad access may happen.
So, If the screen size larger than vga_vram, resize screen should be
failed. This alse fix CVE-2020-8649 and CVE-2020-8647.
Linus pointed out that overflow checking seems absent. We're saved by
the existing bounds checks in vc_do_resize() with rather strict
limits:
if (cols > VC_RESIZE_MAXCOL || lines > VC_RESIZE_MAXROW)
return -EINVAL;
Fixes: 0aec4867dc ("[PATCH] SVGATextMode fix")
Reference: CVE-2020-8647 and CVE-2020-8649
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
[danvet: augment commit message to point out overflow safety]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304022429.37738-1-zhangxiaoxu5@huawei.com
The hierarchical topology with power-domain should be described through
child nodes, rather than as currently described in the PSCI root node. Fix
this by adding a patternProperties with a corresponding reference to the
power-domain DT binding.
Additionally, update the example to conform to the new pattern, but also to
the adjusted domain-idle-state DT binding.
Fixes: a3f048b542 ("dt: psci: Update DT bindings to support hierarchical PSCI states")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[robh: Add missing allOf, tweak power-domain node name]
Signed-off-by: Rob Herring <robh@kernel.org>
The existing binding requires the nodename to have a '@', which is a bit
limiting for the wider use case. Therefore, let's extend the pattern to
allow either '@' or '-'.
Fixes: a3f048b542 ("dt: psci: Update DT bindings to support hierarchical PSCI states")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[robh: drop example change]
Signed-off-by: Rob Herring <robh@kernel.org>
The percpu refcount protects this structure, and we can have an atomic
switch in progress when exiting. This makes it unsafe to just free the
struct normally, and can trigger the following KASAN warning:
BUG: KASAN: use-after-free in percpu_ref_switch_to_atomic_rcu+0xfa/0x1b0
Read of size 1 at addr ffff888181a19a30 by task swapper/0/0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.0-rc4+ #5747
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
<IRQ>
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x3b/0x60
? percpu_ref_switch_to_atomic_rcu+0xfa/0x1b0
? percpu_ref_switch_to_atomic_rcu+0xfa/0x1b0
__kasan_report.cold+0x1a/0x3d
? percpu_ref_switch_to_atomic_rcu+0xfa/0x1b0
percpu_ref_switch_to_atomic_rcu+0xfa/0x1b0
rcu_core+0x370/0x830
? percpu_ref_exit+0x50/0x50
? rcu_note_context_switch+0x7b0/0x7b0
? run_rebalance_domains+0x11d/0x140
__do_softirq+0x10a/0x3e9
irq_exit+0xd5/0xe0
smp_apic_timer_interrupt+0x86/0x200
apic_timer_interrupt+0xf/0x20
</IRQ>
RIP: 0010:default_idle+0x26/0x1f0
Fix this by punting the final exit and free of the struct to RCU, then
we know that it's safe to do so. Jann suggested the approach of using a
double rcu callback to achieve this. It's important that we do a nested
call_rcu() callback, as otherwise the free could be ordered before the
atomic switch, even if the latter was already queued.
Reported-by: syzbot+e017e49c39ab484ac87a@syzkaller.appspotmail.com
Suggested-by: Jann Horn <jannh@google.com>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
'16306a61d3b7 ("fs/locks: always delete_block after waiting.")' add the
logic to check waiter->fl_blocker without blocked_lock_lock. And it will
trigger a UAF when we try to wakeup some waiter：
Thread 1 has create a write flock a on file, and now thread 2 try to
unlock and delete flock a, thread 3 try to add flock b on the same file.
Thread2 Thread3
flock syscall(create flock b)
...flock_lock_inode_wait
flock_lock_inode(will insert
our fl_blocked_member list
to flock a's fl_blocked_requests)
sleep
flock syscall(unlock)
...flock_lock_inode_wait
locks_delete_lock_ctx
...__locks_wake_up_blocks
__locks_delete_blocks(
b->fl_blocker = NULL)
...
break by a signal
locks_delete_block
b->fl_blocker == NULL &&
list_empty(&b->fl_blocked_requests)
success, return directly
locks_free_lock b
wake_up(&b->fl_waiter)
trigger UAF
Fix it by remove this logic, and this patch may also fix CVE-2019-19769.
Cc: stable@vger.kernel.org
Fixes: 16306a61d3 ("fs/locks: always delete_block after waiting.")
Signed-off-by: yangerkun <yangerkun@huawei.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
The bfq_find_set_group() function takes as input a blkcg (which represents
a cgroup) and retrieves the corresponding bfq_group, then it updates the
bfq internal group hierarchy (see comments inside the function for why
this is needed) and finally it returns the bfq_group.
In the hierarchy update cycle, the pointer holding the correct bfq_group
that has to be returned is mistakenly used to traverse the hierarchy
bottom to top, meaning that in each iteration it gets overwritten with the
parent of the current group. Since the update cycle stops at root's
children (depth = 2), the overwrite becomes a problem only if the blkcg
describes a cgroup at a hierarchy level deeper than that (depth > 2). In
this case the root's child that happens to be also an ancestor of the
correct bfq_group is returned. The main consequence is that processes
contained in a cgroup at depth greater than 2 are wrongly placed in the
group described above by BFQ.
This commits fixes this problem by using a different bfq_group pointer in
the update cycle in order to avoid the overwrite of the variable holding
the original group reference.
Reported-by: Kwon Je Oh <kwonje.oh2@gmail.com>
Signed-off-by: Carlo Nonato <carlo.nonato95@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
